小白菜中残留虫酰肼的超临界流体萃取条件的研究

将超临界流体萃取(supercritical fluid extraction,SFE)技术与高效液相色谱分析相结合,建立了特异性杀虫剂虫酰肼的萃取分离方法。SFE对虫酰肼的萃取条件:压力48.3 MPa(7000 psi),温度60 ℃,静态萃取时间20 min,CO2体积10 mL,改性剂甲醇添加量0.04 mL/g,丙酮为收集溶剂。在此条件下,SFE对虫酰肼的萃取率为100.75%,所得样品可直接用于高效液相色谱分析。色谱条件：紫外-二极管阵列检测器(检测波长为245 nm),C18键合色谱柱,乙腈     

Orthogonal test design for optimization of supercritical fluid extraction of daphnoretin, 7-methoxy-daphnoretin and 1,5-diphenyl-1-pentanone from Stellera chamaejasme L. and subsequent isolation by high-speed counter-current chromatography

Supercritical fluid extraction (SFE) of daphnoretin, 7-methoxy-daphnoretin and 1,5-diphenyl-1- pentanone from Stellera chamaejasme L. was performed. An orthogonal L9 (3)4 test design was applied to select the optimum extraction parameters including pressure, temperature, modifier and sample particle size on yield using an analytical-scale SFE system. The process was then scaled up by 100 times using a preparative SFE system under the optimized conditions of 25 MPa of pressure, 45 degrees C of temperature, 40-60 mesh of sample particle size and modified CO2 with 20% methanol. The yield of the crude extract from preparative SFE was 2.65%, which contained daphnoretin 25.2%, 7-methoxy-daphnoretin 22.8% and 1,5-diphenyl-1-pentanone 21.1%, respectively. Then the crude extract was successfully isolated and separated by preparative high-speed counter-current chromatography (HSCCC) with a two-phase solvent system composed of n-hexane-ethyl acetate-methanol-water (10:13:13:10, v/v) by increasing the flow-rate of the mobile phase stepwise from 1.0 to 2.0 ml/min after 90 min. The target compounds isolated and purified by HSCCC were analyzed by high-performance liquid chromatography (HPLC). The separation produced total of 69.2mg of daphnoretin at 99.2% purity, 63.4 mg of 7-methoxy-daphnoretin at 98.7% purity and 58.3 mg of 1,5-diphenyl-1-pentanone at 98.1% purity from 300 mg of the crude extract in one-step separation. The recoveries of daphnoretin, 7-methoxy-daphnoretin and 1,5-diphenyl-1-pentanone were 90.8, 91.5 and 90.4%, respectively, in HSCCC isolation step and the chemical structure identification was carried out by MS, 1H NMR and 13C NMR.     

Efficient new method for extraction and isolation of three flavonoids from Patrinia villosa Juss. by supercritical fluid extraction and high-speed counter-current chromatography

Supercritical fluid extraction (SFE) of orotinin, orotinin-5-methyl ether and licoagrochalcone B from Patrinia villosa was performed. The optimization of parameters including pressure, temperature, modifier and sample particle size on yield was carried out using an analytical-scale SFE system. The process was then scaled up by 100 times using a preparative SFE system under the optimized conditions of 25 MPa, 45 degrees C, a sample particle size 40-60 mesh and modified CO2 with 20% methanol. The yield of the preparative SFE was 2.82% (crude extract I) and the combined yield of orotinin, orotinin-5-methyl ether and licoagrochalcone B was 0.82 mg/g of dry sample mass. Then the crude extract I was re-dissolved in methanol and methanol soluble fraction (crude extract II, 0.17%) was obtained, which was successfully isolated and separated by a preparative high-speed counter-current chromatography (HSCCC) with a two-phase solvent system composed of n-hexane-ethyl acetate-methanol-water (5:6:6:6, v/v/v/v) by increasing the flow-rate of the mobile phase stepwise from 1.0 to 2.0 ml/min after 3 h. The target compounds isolated and purified by HSCCC were analyzed by high performance liquid chromatography. The separation produced total of 38.2 mg of orotinin at 99.2% purity, 19.8 mg of orotinin-5-methyl ether at 98.5% purity and 21.5 mg of licoagrochalcone B at 97.6% purity from 400 mg of the crude extract in a one-step separation. The recoveries of orotinin, orotinin-5-methyl ether and licoagrochalcone B were 91.1, 91.6 and 90.3%, respectively, and the chemical structure identification was carried out by UV, IR, MS, 1H NMR and 13C NMR.     

生附子中C19型二萜生物碱的高速逆流色谱分离及其结构鉴定

应用高速逆流色谱法分离制备了生附子中的3个C19型二萜生物碱类化合物。以正己烷-乙酸乙酯-甲醇-水(3:5:4:5, v/v/v/v)为两相溶剂系统,上相为固定相,下相为流动相,在主机转速850 r/min、流动相流速2.0 mL/min、检测波长235 nm条件下进行分离制备;一次性从90 mg附子总碱粗提物中分离制备得到15.3 mg北草乌碱,35.1 mg中乌头碱和22.7 mg次乌头碱,经高效液相色谱分析,测得它们的纯度分别为97.9%、96.2%和99.2%。并应用波谱(电喷雾离子质谱、核磁共振氢谱和核磁共振13C谱)解析法确定了它们的结构。利用该方法可以对生附子中的二萜类生物碱成分进行快速的分离和纯化     

Isolation and purification of alkaloids from lotus leaves by ionic‐liquid‐modified high‐speed countercurrent chromatography

An effective high‐speed countercurrent chromatography method was successfully established by using ionic liquids as the modifier of the two‐phase solvent system. Adding a small amount of ionic liquids significantly shortens the separation time and improves the separation efficiency. The conditions of ionic‐liquid‐modified high‐speed countercurrent chromatography including solvent systems, types and content of added ionic liquids, and ionic liquids posttreatment were investigated. The established method was successfully applied to separate alkaloids from lotus leaves using a two‐phase solvent system composed of petroleum ether/ethyl acetate/methanol/water/[C₄mim][BF₄] (1:5:1:5:0.15, v/v/v/v/v). Four alkaloids pronuciferine (1.7 mg), N‐nornuciferine (4.3 mg), nuciferine (3.1 mg), and roemerine (2.1 mg) were obtained with the purities of 90.53, 92.25, 99.86, and 98.63%, respectively, from 100 mg crude extract of lotus leaves. The results indicated that the ionic‐liquid‐modified high‐speed countercurrent chromatography method was suitable for alkaloid separation from lotus leaves and would be a promising method for the separation of alkaloids from other natural products.     

Effects of different parameters on supercritical fluid extraction of steroid drugs, from spiked matrices and tablets

Feasibility of supercritical CO(2) extractions of two steroid drugs, medroxyprogesterone acetate (med) and cyproterone acetate (cyp), were evaluated. The effects of temperature (308-348 K), pressure (100-300 bar), static extraction time (5-15 min), dynamic extraction time (10-30 min) and percent methanol modifier (1-10% v/v) on the SFE recoveries of these drugs from spiked matrices (glass) and pharmaceutical dosages (tablets) were investigated. The results showed that minor structural differences between related compounds might lead to dramatically differences in extraction behaviors under the same conditions. The optimum SFE conditions to extract the drugs from spiked glass were 10 min static, 30 min dynamic, 300 bar, 348 K and 5% modifier in the case of med acetate and 10 min static, 30 min dynamic, 100 bar, 308 K, and 10% modifier in the case of cyp. Under these conditions above 90% of the total recovery was obtained for both drugs. Extractions from pharmaceutical dosages were less efficient compared to glass beads under the same conditions. Quantitative recovery of solutes from tablets were obtained upon changing extraction conditions to: 15 min static, 45 min dynamic, P=300 bar, 20% modifier (for med) and 10% (for cyp).     

An efficient combination of supercritical fluid extraction and high‐speed counter‐current chromatography to extract and purify homoisoflavonoids from Ophiopogon japonicus (Thunb.) Ker‐Gawler

Supercritical fluid extraction (SFE) was used to extract homoisoflavonoids from Ophiopogon japonicus (Thunb.) Ker‐Gawler. The optimization of parameters was carried out using an orthogonal test L₉ (3)⁴ including pressure, temperature, dynamic extraction time and the amount of modifier. The process was then scaled up by 100 times with a preparative SFE system under the optimized conditions of 25 MPa, 55°C, 4.0 h and 25% methanol as a modifier. Then crude extracts were separated and purified by high‐speed counter‐current chromatography (HSCCC) with a two‐phase solvent system composed of n‐hexane/ethyl acetate/methanol/ACN/water (1.8:1.0:1.0:1.2:1.0 v/v). There three homoisoflavonoidal compounds including methylophiopogonanone A 6‐aldehydo‐isoophiopogonone A, and 6‐formyl‐isoophiopogonanone A, were successfully isolated and purified in one step. The collected fractions were analyzed by HPLC. In each operation, 140 mg crude extracts was separated and yielded 15.3 mg of methylophiopogonanone A (96.9% purity), 4.1 mg of 6‐aldehydo‐isoophiopogonone A (98.3% purity) and 13.5 mg of 6‐formyl‐isoophiopogonanone A (97.3% purity) respectively. The chemical structure of the three homoisoflavonoids are identified by means of ESI‐MS and NMR analysis.     

Supercritical fluid extraction of aurentiamide acetate from Patrinia villosa Juss and subsequent isolation by silica gel and high-speed counter-current chromatography

Supercritical fluid extraction (SFE) of aurentiamide acetate from Patrinia villosa Juss was performed. The optimization of parameters was carried out using an analytical-scale supercritical fluid extraction (SFE) system. Then the extraction was scaled up by 100 times using a preparative SFE system under the optimized conditions of 55 degrees C, 35 MPa and modified CO2 with 10% methanol. Then, the crude extract I obtained by SFE was chromatographed on silica gel and the solvent system composed of petroleum ether-ethyl acetate (5:1, v/v) was used to produce the crude extract II, which was further isolated and purified by high-speed counter-current chromatography (HSCCC) with a two-phase solvent system composed of n-hexane-ethyl acetate-methanol-water (1:1.2:1.2:1, v/v/v/v). One hundred fifty-five milligrams of aurentiamide acetate was obtained from 400 mg crude extract II (contained 42% target) with a purity of 99.3% determined by HPLC and 92.3% recovery in one-step elution, and identification was performed by UV, MS, 1H NMR and 13C NMR. As far as we know, this is the first report of discovering aurentiamide acetate from the plant of Patrinia genius.     

Supercritical CO2 extraction of emodin and physcion from Polygonum cuspidatum and subsequent isolation by semipreparative chromatography

Emodin and physcion are abundant anthraquinone compounds found in the traditional Chinese medicinal herb Polygonum cuspidatum Sied. et Zucc. In this paper, emodin and physcion were successfully extracted with supercritical CO2 plus ethanol modifier after the extraction conditions were optimized with uniform design-sequential optimization. Results showed that the ethanol modifier concentration was the main factor for the effective extraction of the emodin. The optimal extraction condition was obtained: 20 MPa, 30 degrees C, and 95% ethanol, at which the yields of emodin and physcion were 0.616 and 0.178 g/100 g, respectively. The yield obtained by supercritical fluid extraction (SFE) was a little lower than that obtained by sonication extraction (SE). The crude extract obtained by SFE was further isolated and purified by semipreparative chromatography with the mobile phase composed of methanol-water (90:1, v/v). Emodin and physcion were obtained with purity 98.6 and 99.1%, respectively, when determined by HPLC, and identification was performed by retention time and UV spectra of the standards. The result suggested that SFE is an alternative and promising method for extraction of the two compounds from P. cuspidatum owing to its environment-friendly properties and fewer coextracts.     

Supercritical fluid extraction of amino acids from birch (Betula pendula Roth) leaves and their liquid chromatographic determination with fluorimetric detection

A method for supercritical fluid extraction (SFE) of amino acids was adapted and optimal experimental conditions were selected for a matrix consisting of dry leaves. The matrix-dependent SFE method uses a mixture of MeOH-H(2)O-acetonitrile (10:10:1 v/v/v) as a modifier (0.5 mL in situ, 300 muL on-line) at 70 degrees C and 40 MPa and no HCl is needed as an entrainer. The amino acids were quantified using high-performance liquid chromatography with fluorimetric detection (HPLC/FLD) after gradient elution on Zorbax Eclipse AAA columns (4.6x150 mm, 3.5 mum) with aqueous Na(2)HPO(4 )buffer of pH 7.8 and ACN-MeOH-water as a mobile phase. In comparison with Soxhlet extraction, SFE gave higher recovery and selectivity, but it required longer extraction time (90 min) and it was more labor-intensive (clean-up step after the pre-concentration). Both methods should be used separately or in combination according to the matrix, number of samples, and levels of ballast compounds.     

On-line coupling of supercritical CO2 extraction with reversed-phase liquid chromatography for the quantitative analysis of analytes in aqueous matrices

The first report of on-line coupled supercritical fluid extraction (SFE) with reversed-phase liquid chromatography for the quantitative analysis of analytes in aqueous matrices is described. Two commercial systems (e.g. SFE and HPLC) were connected via a single six-port injection valve. By using water to eliminate residual decompressed CO2 gas in the solid-phase extraction trap, quantitative extraction and transfer were achieved for the target analytes (progesterone, phenanthrene, and pyrene) spiked in water, as well as in real samples (urine and environmental water). During each extraction, no restrictor plugging was realized. Extraction temperature and pressure were optimized. Different amounts of salt were added to the aqueous matrix to enhance ionic strength and thus extraction efficiency. Methanol and 2-propanol were used as CO2 modifiers. Compared with dynamically mixing modifier with the CO2 extraction fluid, pre-spiking the same amount of modifier in the extraction vessel enhanced the recovery approximately 30% for progesterone, phenanthrene, and pyrene due to a "co-extraction effect".     

Efficiency of supercritical fluid extraction for determining 4-nonylphenol in municipal sewage sludge.

When the sewage sludge containing the persistent, lipophilic, metabolite 4-nonylphenol (4-NP) has been disposed of in the environment it's toxic nature can lead to serious health risks to human beings and can also affect plants and aquatic organisms. Supercritical fluid extraction (SFE) is a new and powerful technique for extracting the organic contaminants from the solid phase. The present study was conducted to investigate optimal conditions for the quantitative extraction of 4-NP by SFE and to determine the concentration of 4-NP in municipal sewage sludge. The effect of several parameters such as temperature, pressure, static extraction time, dynamic extraction time, CO2 flow-rate, sample mass and modifier on the extraction were investigated. The optimal conditions for the extraction of the spiked sample were fluid pressure 97 bar, temperature 40 degrees C, flow-rate 3.0 ml/min, static extraction time 2 min, dynamic extraction time 5 min and modifier methanol (0.5 ml). Extracts were analyzed by gas chromatography-mass spectrometry. Concentration of 4-NP in the anaerobically degraded sludge of the De-Haw Sewage Treatment Plant in Taiwan was found to be 243.9 mg/kg. The extraction efficiency of the SFE method was compared with the conventional Soxhlet extraction method. The overall recovery of the SFE method was found to be greater and the results indicate that SFE is an efficient method for extracting 4-NP from sewage sludge.     

Development of supercritical fluid extraction with a solid-phase trapping for fast estimation of toxic load of polychlorinated dibenzo-p-dioxins-dibenzofurans in sawmill soil

A method consisting of automated supercritical fluid extraction (SFE) with simultaneous cleanup by a solid-phase trap was developed for fast analysis of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) in soil. SFE was optimised to replace conventional liquid-based methods in routine analyses of PCDD/PCDFs in sawmill soil contaminated by a chlorophenol formulation. PCDD/PCDFs were quantitatively extracted in 60 min using CO2 at 400 atm and 100 degrees C without a modifier. A trap containing a small amount of activated carbon mixed with Celite efficiently collected PCDD/PCDFs after SFE. After SFE co-extracted impurities were eluted out from the trap with 4 ml of hexane and PCDD/PCDFs were eluted with 10 ml of toluene. The concentrations and TCDD-equivalent of PCDD/PCDFs corresponded to the results of traditional solvent extraction method (Soxhlet) in six sawmill soils tested. The performance of the trap was maintained over a long period of time (nearly 100 extractions).     

Supercritical fluid extraction and gas chromatography analysis of arsenic species from solid matrices

A method in combination with derivatization-supercritical fluid extraction(SFE) and gas chromatography(GC) for the speciation and quantitative determination of dimethylarsinate(DMA), monomethylarsonate(MMA) and inorganic arsenic in solid matrices was investigated. Thioglycolic acid methyl ester(TGM) and thioglycolic acid ethyl ester(TGE) were evaluated as derivatization reagents. The effects of pressure, temperature, flow rate of supercritical CO_2, extraction time, modifier and microemulsion on the efficiency of extraction were systematically investigated. The procedure was applied to the analysis of real soil and sediment samples. Results showed that TGE was more effective for arsenic speciation as a derivatization reagent. Modifying supercritical CO_2 with methanol can greatly improve the extraction efficiency. Further, the addition of microemulsion containing surfactant Triton X-100 can further enhance recoveries of arsenic species. The optimum extraction conditions were 100 ℃, 30 MPa, 10 min static and 25 min dynamic extraction with 5%(v/v) methanol, and surfactant modified supercritical CO_2. Detection limits in solid matrices were 0.15, 0.3 and 1.2 mg/kg for DMA, MMA and inorganic arsenic,respectively. The method was validated by the recovery data. The resulting method was fast, easy to perform and selective in the extraction and detection of various arsenic species in solid matrices.     

Combination of supercritical fluid extraction with counter‐current chromatography to isolate anthocyanidins from the petals of Chaenomeles sinensis based on mathematical calculations

Supercritical fluid extraction (SFE) coupled with high‐speed counter‐current chromatography (HSCCC) was successfully used for the extraction and on‐line isolation of the anthocyanidins from the petals of Chaenomeles sinensis in two stages. The SFE parameters were optimized by an orthogonal test, and the solvent systems of SFE and HSCCC were calculated and optimized with the help of a multiexponential function model. In the first stage, the lower phase of the solvent system of n‐butanol/tert‐butyl methyl ether/acetonitrile/0.1% aqueous TFA (0.715:1.0:0.134:1.592, v/v/v/v) was used as both the SFE modifier and the HSCCC stationary phase, after extraction, the extractants were pumped into HSCCC column, and then eluted with the corresponding upper phase to isolate the moderately hydrophobic compounds. In the second stage, the upper phase of the solvent system of n‐butanol/ethyl acetate/acetonitrile/0.1% aqueous TFA (1.348:1.0:0.605:2.156, v/v/v/v) was used as both the SFE modifier and the HSCCC stationary phase, followed by elution with the corresponding lower phase to separate the hydrophobic compounds. With the help of two‐stage SFE/HSCCC, six compounds including delphinidin‐3‐O‐glucoside (Dp3G), cyanidin‐3‐O‐glucoside (Cy3G), peonidin‐3‐O‐glucoside (Pn3G), delphinidin (Dp), peonidin (Pn), and malvidin (Mv) were successfully separated within 300 min. The targeted compounds were identified by UV spectrophotometry, MS, and NMR spectroscopy. This research has opened up great prospects for the industrial application of SFE–HSCCC for the automatic extraction and separation of unstable compounds.     

Comparison of supercritical fluid and Soxhlet extractions for the isolation of nitro compounds from soils

Supercritical fluid extraction (SFE) with CO(2), a clean and rapid alternative to conventional Soxhlet extraction, was investigated for the extraction of nitro compounds from soil samples. Quantitative extraction by SFE was accomplished at a pressure of 25 MPa and an extraction temperature of 60 degrees C, for 30 min in dynamic mode and using acetonitrile as modifier, and the results were comparable with those obtained by acetonitrile Soxhlet extraction (3 h) for all soil samples. Extracts from these two procedures were analyzed by gas chromatography coupled with mass spectrometry. Quantitative reproducibility for SFE extracts was acceptable (RSD 2-10%), and the quantity of solvent was reduced from 160 mL for Soxhlet extraction to 5 mL in the case of SFE.     

An efficient new method for extraction, separation and purification of psoralen and isopsoralen from Fructus Psoraleae by supercritical fluid extraction and high-speed counter-current chromatography

Psoralen and isopsoralen were extracted from Fructus Psoraleae (Psoralea corylitolia L.) by supercritical CO2. The effect of various parameters, i.e., pressure, temperature and sample particle size on yield was investigated with an analytical-scale supercritical fluid extraction (SFE) system to find the optimal conditions. The process was then scaled up by 50 times with a preparative SFE system under the optimized conditions of pressure (26 MPa), temperature (60 degrees C) and a sample particle size of 40-60 mesh. The yield of the preparative SFE was 9.1% and the combined yield of psoralen and isopsoralen was 2.5 mg/g of dry seeds. Psoralen and isopsoralen in the extract were separated and purified by high-speed counter-current chromatography with a two-phase solvent system composed of n-hexane-ethyl acetate-methanol-water (1:0.7:1:0.8, v/v), and the fractions were analyzed by HPLC, MS, 1HNMR and 13C NMR. The structures of the products were further confirmed by comparison with authentic samples (National Institute of the Control of Pharmaceutical and Biological Products, Beijing, China).     

Sub-critical fluid extraction of morphinic alkaloids in urine and other liquid matrices after adsorption on solid supports

Summary Supercritical fluid extraction (SFE) of liquid matrices is difficult and requires special instrumentation. An alternative is to load the liquid on a solid support prior to extraction. This procedure yields higher selectivity and can be used as a clean-up step when very complex liquid matrices, such as urine, are to be analyzed. This paper demonstrates the use of various solid supports in order to extract morphinic alkaloids with subcritical fluids (CO₂ + polar modifier). Optimization of the procedure with regard to loading conditions, SFE parameters such as pressure, extraction time, flow rate and eluent composition, was carried out with morphinic alkaloids in aqueous solution. As a real-life application, SFE of opiates in urine were tested with two silica bonded phase supports (C18 (polygosil 60-4063, from Macherey-Nagel) and Bond Elut Certify from Analytichem International). Recovery, variation coefficients and linearity are described for each procedure. Bond Elut Certify silica was chosen as the best solid support and SFE is compared with conventional solid phase extraction.     

Isolation and Extraction of Total Flavonoids from Epimedium Koreanum Nakai by Supercritical Fluid Extraction

In the present paper is reported the metnocl for the isolation and extraction of total flavonoids of Epimedium Koreanum Nateai by means of supercritical fluid extraction(SFE). By examining pressure, temperature, amounts of modifier and extraction time, the optimized condition of SFE is confirmed as 30 MPa and 60℃, with 70% ethanol as the modifier. The samples were statically extracted for 30 min, followed bydynamic extraction for 120 min at a flow rate of 6 mL/min. The quantitative analysis of total flavonoids was performed by UV-Vis spectrophotometry. Compared with the conventional method, the SFE method is more efficient, more rapid and more friendly environmentally.     

Supercritical fluid extraction for pesticide multiresidue analysis in honey: determination by gas chromatography with electron-capture and mass spectrometry detection

An analytical procedure using supercritical fluid extraction (SFE) and capillary gas chromatography with electron-capture detection was developed to determine simultaneously residues of different pesticides (organochlorine, organophosphorus, organonitrogen and pyrethroid) in honey samples. Fortification experiments were conducted to test conventional extraction (liquid-liquid) and optimize the extraction procedure in SFE by varying the CO2-modifier, temperature, extraction time and pressure. Best efficiency was achieved at 400 bar using acetonitrile as modifier at 90 degrees C. For the clean-up step, Florisil cartridges were used for both methods LLE and SFE. Recoveries for majority of pesticides from fortified samples of honey at fortification level of 0.01-0.10 mg/kg ranged 75-94% from both methods. Limits of detection found were less than 0.01 mg/kg for ECD and confirmation of pesticide identity was performed by gas chromatography-mass spectrometry in selected-ion monitoring mode. The multiresidue methods in real honey samples were applied and the results of developed methods were compared.