A new HPLC method of hydrophobicity evaluation employing poly (butadiene)-coated alumina columns

Summary The limitations of the existing methods and procedures of hydrophobicity evaluation by high-performance liquid chromatography are pointed out and a new approach is described allowing convenient, fast, and reproducible hydrophobicity quantitation for diverse basic, neutral, and acidic solutes of different chemical classes. The method is based on using poly(butadiene)-coated alumina developed by Schomburg and co-workers as the stationary phase which can be operated under wide range of eluent pH and which shows no tendency for specific interactions with solutes, typical for silica-based reversed-phase materials.     

CE of poly(amidoamine) succinamic acid dendrimers using a poly(vinyl alcohol)-coated capillary

Various generations (G1-G8) of negatively charged poly(amidoamine) (PAMAM) succinamic acid dendrimers (PAMAM-SAH) were analyzed by CE using a poly(vinyl alcohol)-coated capillary. Due to its excellent stability and osmotic flow-shielding effect, highly reproducible migration times were achieved for all generations of dendrimer (e.g., RSD for the migration times of G5 dendrimer was 0.6%). We also observed a reverse trend in migration times for the PAMAM-SAH dendrimers (i.e., higher generations migrated faster than lower generation dendrimers) compared to amine-terminated PAMAM dendrimers reported in the literature. This reversal in migration times was attributed to the difference in counterion binding around these negatively charged dendrimers. This reverse trend allowed a generational separation for lower generation (G1-G3) dendrimers. However, a sufficient resolution for the migration peaks of higher generations (G4-G5) in a mixture could not be achieved. This could be due to their nearly identical charge/mass ratio and dense molecular conformations. In addition, we show that dye-functionalized PAMAM-SAH dendrimers can also be analyzed with high reproducibility using this method.     

Surface characterization of functional poly(diacetylene) and poly(butadiene) mono- and multilayers

The surface properties of Langmuir-Blodgett mono- and multilayers of a variety of amphiphilic poly(diacetylene)s and poly(butadiene)s were investigated by contact angle, streaming potential, ellipsometry, and X-ray photoelectron spectroscopic (XPS) measurements. Captive air and octane angles varied between approximately 60° and 105° for hydrophobicx-layers and 31° to 46° for hydrophilic surfaces depending on the particular head group, whereas advancing angles determined via the vertical plate method are considerably higher. Negative streaming potentials were obtained for all surfaces. Positively charged monolayers yielded less negative- potential values (–28 mV) than negatively charged (–52 mV) or hydrophobic (–50 mV) layers. Ellipsometry measurements yielded an average layer thickness of 27±6 Å for 3 to 11 layers. X-ray photoelectron spectroscopy results qualitatively confirmed the expected composition. All of the samples, which were handled and stored in air after deposition and polymerization, were surface oxidized.Dedicated to Prof. Dr. F. H. Müller.     

Studies on synthesis and properties of poly(ferrocenyldimethylsilanes) and poly(ferrocenylmethylphenylsilanes)

Poly(ferrocenyldimethylsilane) and poly(ferrocenylmethylphenylsilane) have been prepared via the thermal ring-opening polymerization of the corresponding strained, silicon-bridged ferrocenophanes. It was found that the molecular weights of resultant polymers depend on the polymerization time. Their electrochemical behavior in aqueous electrolytes was investigated by cyclic voltammetry.     

New architectures of poly(ethylene glycol) and poly(methylthiirane) in block copolymers

Two synthetic ways were experimented to prepare new architectures of block copolymers made of poly(ethylene glycol) (PEG) and poly(methylthiirane). The coupling of both blocks conveniently end-capped as well as anionic polymerization of methylthiirane initiated by PEG-thiols gave readily the copolymers. Their characterization by ¹H NMR, SEC and IR confirmed the expected structures.     

Synthesis and characterization of model diblock copolymers of poly(dimethylsiloxane) with poly(1,4‐butadiene) or poly(ethylene)

Model diblock copolymers of poly(1,4‐butadiene) (PB) and poly(dimethylsiloxane) (PDMS), PB‐b‐PDMS, were synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene and hexamethylciclotrisiloxane (D₃) in the presence of sec‐BuLi. By homogeneous hydrogenation of PB‐b‐PDMS, the corresponding poly(ethylene) and poly(dimethylsiloxane) block copolymers, PE‐b‐PDMS, were obtained. The synthesized block copolymers were characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size‐exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and rheology. SEC combined with ¹H NMR analysis indicates that the polydispersity index of the samples (M_w/M_n) is low, and that the chemical composition of the copolymers varies from low to medium PDMS content. According to DSC and TGA experiments, the thermal stability of these block copolymers depends on the PDMS content, whereas TEM analysis reveals ordered arrangements of the microphases. The morphologies observed vary from spherical and cylindrical to lamellar domains. This ordered state (even at high temperatures) was further confirmed by small‐amplitude oscillatory shear flow tests. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1579–1590, 2006     

Poly (2,6-dimethyl-1,4-phenylene oxide)/poly (butadiene) diol interpenetrating polymer networks: Phase morphological characteristics and glass transition temperature behavior

The fracture surface topography of simultaneous interpenetrating polymer networks (SIN'S) of poly (2,6-dimethyl-1,4 phenylene oxide) (PPO)/poly (butadiene) diol was examined by scanning electron microscopy (SEM). The phase morphology of the IPNs is highly dependent on PPO/poly (butadiene) diol mass ratio. A single-phase morphology of the IPNs was achieved when the content of poly (butadiene) diol is below 40 wt % in the initial composition. The SEM observations are also wholly consistent with the glass transition temperature behavior obtained in the differential scanning calorimetric (DSC) measurements. © 1994 John Wiley & Sons, Inc.     

A sol-gel immobilization of nano and micron size sorbents in poly(dimethylsiloxane) (PDMS) microchannels for microscale solid phase extraction (SPE)

Sorbent particles consisting of nano and micro silica, and micron size octadecylsilica (ODS) were immobilized using sol-gel chemistry onto poly(dimethylsiloxane) (PDMS) microfluidic channels to serve as μ-chip solid phase extraction (SPE) devices. Extraction, preconcentration and purification of biological and chemical analytes were carried out using these. Micro and nano scale silica-immobilized μ-SPE were used for the extraction/purification of DNA from recombinant Escherichia coli crude lysate. The average DNA recovery was 77 ± 9% (X ± R.S.D.) for the micron size silica particles and 70 ± 5% (X ± R.S.D.) for the nano silica particles. The extracted DNA could be amplified by polymerase chain reaction (PCR) whereas the DNA from the crude lysate solution could not be. This was a testimony to the purification capability of the μ-SPE device. ODS immobilized μ-SPE were used to study the extraction efficiency (EE) and enhancement factor (EF) for three groups of organic compounds, aromatics, phenols and carboxylic acids. They showed poor recovery and low enrichment because the analytes sorbed into the PDMS and were not quantitatively extracted.     

Determination of the glass transition temperature of polystyrene,poly(vinyl chloride) and poly(methyl methacrylate) using gas chromatography

The glass transition temperatures, Tg, of polystyrene, poly (vinyl chloride) and poly(methyI methacrylate) have been determined from gas chromatographic measurements using n-hexane, n-heptane, meta-xylene and para-xylene solvents. The glass transition temperatures were detected on the z-shaped retention diagrams which were produced from the plot of the logarithm of the specific retention volumes of the above-mentioned solvents against the reciprocal of temperature, i.e. log V${}_{\text{g}}^{\text{º}}$ vs. 1/T. The glass transition temperature is specified by the temperature where the slope of log V${}_{\text{g}}^{\text{º}}$ vs. 1/T changes abruptly. The observed glass transition temperature of polystyrene produced by this technique was found to be in good agreement with those produced by other techniques such as the differential scanning colorimeter. The industrial importance of the glass transition temperature, T_g, might be due to the dramatic changes in the physical properties of the polymer, such as hardness and elasticity, which take place in the vicinity of this temperature. However, perfectly crystalline polymers do not exhibit glass transitions, because their chains are incorporated in regions of three-dimensional order, called crystallites. Completely amorphous polymers and semi-crystalline polymers usually exhibit both glass transition and melting.     

The absorption of organic liquids in poly(aryl-ether-ether-ketone) [PEEK]

The absorption and subsequent desorption of benzene, toluene, carbon disulfide, and chloroform in amorphous and 27% crystalline poly (aryl-ether-ether-ketone) (PEEK) were determined. At 35°C, the equilibrium weight gain (solubility) of benzene, toluene, chloroform, and CS₂ are 23.5, 19.8, 51.2, and 21.2 wt%, respectively. The initial weight gain is linear with root-time and pseudodiffusion constants for absorption into amorphous PEEK ranging from 0.35 to 9.85 x 10^-12m²/s were calculated. The desorption processes are two-step and are controlled by the T_g of the penetrant-resin mixture. The rate of diffussion into the crystalline material is extremely slow; crystalline PEEK reaches saturation (12.5 wt%) after immersion in CS₂ (35°C) for several hundred hours but, even after 1300 h immersion, the other fluids do not reach saturation.     

Performance of biodegradable microcapsules of poly(butylene succinate), poly(butylene succinate-co-adipate) and poly(butylene terephthalate-co-adipate) as drug encapsulation systems

Poly(butylene succinate) (PBSu), poly(butylene succinate-co-adipate) (PBSA) and poly(butylene terephthalate-co-adipate) (PBTA) microcapsules were prepared by the double emulsion/solvent evaporation method. The effect of polymer and poly(vinyl alcohol) (PVA) concentration on the microcapsule morphologies, drug encapsulation efficiency (EE) and drug loading (DL) of bovine serum albumin (BSA) and all-trans retinoic acid (atRA) were all investigated. As a result, the sizes of PBSu, PBSA and PBTA microcapsules were increased significantly by varying polymer concentrations from 6 to 9%. atRA was encapsulated into the microcapsules with an high level of approximately 95% EE. The highest EE and DL of BSA were observed at 1% polymer concentration in values of 60 and 37%, respectively. 4% PVA was found as the optimum concentration and resulted in 75% EE and 14% DL of BSA. The BSA release from the capsules of PBSA was the longest, with 10% release in the first day and a steady release of 17% until the end of day 28. The release of atRA from PBSu microcapsules showed a zero-order profile for 2 weeks, keeping a steady release rate during 4 weeks with a 9% cumulative release. Similarly, the PBSA microcapsules showed a prolonged and a steady release of atRA during 6 weeks with 12% release. In the case of PBTA microcapsules, after a burst release of 10% in the first day, showed a parabolic release profile of atRA during 42 days, releasing 36% of atRA.     

Crystallization behavior and biodegradation of poly(3-hydroxybutyrate) and poly(ethylene glycol) multiblock copolymers

Block copolymerization by using isocyanates is an effective method for incorporating PHB and PEG because it can prepare copolymers with good properties, such as toughness, strength, and so on. In this study, we adopted soil suspension system to estimate the biodegradability of a series of PHB/PEG multiblock copolymers with different compositions and block lengths. In the degradation process, the changes in weight loss, molecular weight, and tensile strength were periodically measured to determine the biodegradability, and the surface morphology was also observed by SEM. In contrast to pure PHB, the weight loss of the copolymer was relatively lower. On the other hand, the tensile strength and molecular weight experienced apparent decrease, and for BHG1000-3-1, they reached 46.7% and 77.7% of the initial value, respectively. SEM observation showed that the surface was covered with numerous erosion pits. All these indicate that the degradation indeed took place and long-chain molecules have been hydrolyzed into shorter ones. The crystallization behavior was also investigated by DSC and WAXD. The results showed that both the segments, PEG and PHB, can form crystalline phases at lower PHB contents ranging from 29% to 44%, and when PHB component was more than 60%, only PHB phase can crystallize.     

Effects of miscible diluent of poly(ether imide) on ring-banded morphology of poly(trimethylene terephthalate)

The melting, crystallization, and self-packed ring patterns in the spherulites of miscible blends comprising poly(trimethylene terephthalate) (PTT) and poly(ether imide) (PEI) were revealed by optical, scanning electron microscopies (PLM and SEM) and differential scanning calorimetry (DSC). Morphology and melting behavior of the miscible PTT/PEI blends were compared with the neat PTT. Ringed spherulites appeared in the miscible PTT/PEI blends at all crystallization temperatures up to 220 °C, whereas at this high temperature no rings were seen in the neat PTT. A postulation was proposed, and interrelations between rings in spherulites and the multiple lamellae distributions were investigated. The specific interactions and the segregation of amorphous PEI were discussed for interpreting the morphological changes of 220 °C-melt-crystallized PTT/PEI samples. Interlamellar segregation of PEI might be associated with multiple lamellae in the spherulites of PTT/PEI blends; therefore, rings were more easily formed in the PTT/PEI blends at all crystallization temperatures. A postulated model of uneven lamellar growth, coupled with periodical spiraling, more properly describes the possible origin of ring bands from combined effects of both interactions and segregation between the amorphous PEI and PTT in blends.     

Monolithic columns based on a poly(styrene-divinylbenzene-methacrylic acid) copolymer for capillary liquid chromatography of small organic molecules

A very simple and readily performed method is described for the preparation of poly(styrene-divinylbenzene-methacrylic acid) monolithic columns for capillary liquid chromatography. The effect of the methacrylic acid content on the morphological and chromatographic properties has been investigated. Methacrylic acid is shown to be essential for isocratic separations of small organic analytes by capillary liquid chromatography. Column efficiencies of about 28,000 theoretical plates/m have been obtained for all the test compounds. The batch-to-batch and run-to-run repeatability of the retention times is better than 1.5%.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

Thermal, ozone and gamma ageing of styrene butadiene rubber and poly(ethylene-co-vinyl acetate) blends

Ageing behaviour of SBR/EVA blends due to the effects of heat, ozone, and gamma radiation was studied with reference to blend ratio, three crosslinking systems (sulfur, peroxide and mixed) and a compatibiliser (SEBS-g-MA). It was found that an increase in the EVA content of the blends enhanced the ageing characteristics. Among the different crosslinking systems, a peroxide cured system exhibited the best retention of properties even after severe ageing. Tensile strength of peroxide cured SBR/EVA blends increased slightly after ageing for three days at 70 °C due to continued crosslinking, whereas tensile strength of all blends decreased on ageing at 100 °C. Compatibilisation with SEBS-g-MA improved the thermal, gamma and water ageing resistance of SBR/EVA blends.     

Pervaporation of alcohol-toluene mixtures through polymer blend membranes of poly(acrylic acid) and poly(vinyl alcohol)

Homogeneous membranes were prepared by blending poly(acrylic acid) with poly(vinyl alcohol). These blend membranes were evaluated for the selective separation of alcohols from toluene by pervaporation. The flux and selectivity of the membranes were determined both as a function of the blend composition and of the feed mixture composition. The results showed that a polymer blending method could be very useful to develop new membranes with improved permselectivity. The pervaporation properties could be optimized by adjusting the blend composition. All the blend membranes tested showed a decrease in flux with increasing poly(vinyl alcohol) content for both methanol—toluene and ethanol—toluene liquid mixtures. The alcohols permeated preferentially through all tested blend membranes, and the selectivity values increased with increasing poly(vinyl alcohol) content. The pervaporation characteristics of the blend membranes were also strongly influenced by the feed mixture composition. The fluxes increased exponentially with increasing alcohol concentration in the feed mixtures, whereas the selectivities decreased for both liquid mixtures.     

Degradation of poly(vinyl butyral) and its stabilization by bases

This paper describes the effect of several bases, including sodium hydroxide, calcium hydroxide, barium hydroxide and hexamine ((CH₂)₆N₄) on thermal stability of poly(vinyl butyral) (PVB). The characterization techniques used were visual colour comparison, thermogravimetric analysis (TG), infra-red spectroscopy, and UV-vis absorption spectra. Visual colour comparison and TG results showed that some acids or other substances that were easily oxidised into acids caused the degradation of PVB. However, PVB could be stabilized to different degrees by adding various bases. The infra-red spectra and UV-vis absorption spectra revealed that during the thermal degradation of PVB mixed with barium hydroxide and hexamine separately, the bases prevented the opening of the cyclic acetal ring and the production of conjugated groups which could cause the colour change.     

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide),PEG-b-(PNIPAM)_2,were successfully synthesized through atom transfer radical polymerization(ATRP).A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether(PEG).The copolymers were obtained via the ATRP of N-isopropylacrylamide(NIPAM) at 30℃with CuCl/Me_6TREN as a catalyst system and DMF/H_2O(v/v = 3:1) mixture as solvent.The resulting copo...     

Crystallization kinetics and morphology of poly(vinylidene fluoride)/poly(ethylene adipate) blends

The miscibility, isothermal crystallization kinetics and morphology of the poly(vinylidene fluoride)(PVDF)/poly(ethylene adipate)(PEA) blends have been studied by differential scanning calorimetry(DSC), optical microscopy(OM) and scanning electron microscopy(SEM). A depression of the equilibrium melting point of PVDF was observed. From the melting point data of PVDF, a negative but quite small value of the interaction parameter ?PVDF-PEA is derived using the Flory-Huggins equation, implying that PVDF shows miscibility with PEA to some extent. Nonisothermal and isothermal crystallization kinetics suggest that the crystallization rate of PVDF decreases with increasing the amount of PEA, and a contrary trend was found when PEA crystallizes with the increase of the amount of PVDF. It was further disclosed that the blend ratio and crystallization temperature affect the texture of PVDF spherulites greatly, which determines the subsequent crystallization of PEA. At high temperatures, e.g. 150 ℃, the band spacing of PVDF spherulites increases with the addition of PEA content and the spherulitic structure becomes more open. In this case, spherulitic crystallization of PEA is not observed for all blend compositions. At low temperatures, e.g. 130 ℃, for the PEA-rich blends, the interpenetrated structures are eventually formed by the penetration of the spherulites of PEA growing within the pre-existing PVDF spherulites.