化学镀镍—高磷合金的微观结构及晶化行为研究

采用混合络合剂在酸性体系中进行化学镀镍－高磷合金,并用原子力显微镜（AFM）,透射电镜（TEM）、差热分析（DSC）、X射线衍射（XRD）等技术研究所得到的化学镀镍－高磷合金的微观结构和晶化行为。结果表明,化学镀镍－高磷合金具有胞状结构的微观形貌,镀态时呈典型的非晶态结构,300℃以下对热非常。镀层在343．8℃开始晶化,400℃时完全转化成亚稳用Ni5P2,440.4 ℃,时进一步转变成稳定的Ni和Ni3P相其晶化行为同从碱性乙二胺镀液中得到的高磷化学镀镍层有明显的差异。     

异相晶核法液相合成金红石型TiO2纳米晶

分别以SnCl₂·2H₂O和SnCl₄·5H₂O为锡源,采用胶溶晶核法,经沉淀和胶溶过程,在液相中一步合成了金红石型TiO₂.详细考察了各种胶溶条件对产物结构的影响,并通过两种锡源实验结果的比较对异相晶核法中两种锡源的成晶机理进行了分析.所合成的金红石型TiO₂晶粒度为20～50nm,两种方法获得完全金红石型TiO₂所需引入SnO₂的最低物质的量的分数分别为10%和8%.     

化学镀镍-高磷合金晶化行为的现场XRD研究

从柠檬酸-酒石酸-乳酸-EDTA混合体系中得到含P 12％(质量比)的化学镀高磷Ni-P合金，其差热曲线显示，在350和420 ℃出现两个放热过程.现场XRD分析结果显示，镀层在300 ℃以下保持非晶态结构，在320 ℃之后开始晶化，首先析出介稳的Ni5P2和Ni12P5相，在360 ℃后开始有稳定的Ni3P和Ni相的衍射峰出现， 400 ℃以上只有Ni3P和Ni相. 325 ℃恒温时，镀层在4 min内保持非晶态的衍射特征，随即析出Ni5P2和Ni12P5相, 并在2 h内基本保持不变. 350 ℃恒温时，析出的Ni5P2和Ni12P5介稳相只存在40 min.实验结果表明, DTA曲线上350 ℃的放热峰不仅有非晶相转变为介稳相的过程，也包含部分介稳相转化为稳定相的过程.     

SnCl4对纳米二氧化钛晶相结构的低温转变控制研究

采用二种方法制备了低温下晶相结构可控制转变的纳米二氧化钛。一种方法是采用乙醇作溶剂的溶胶-凝胶法,通过控制SnCl₄的添加量,便可在450℃热处理下实现纳米TiO₂从纯锐钛矿到不同比例的复合相直至纯金红石相的转变。另一种方法是采用钛酸丁酯为原料直接低温水解,通过加入不同量的SnCl₄,制备了具有晶态结构的二氧化钛复合溶胶,在120℃下干燥处理便可实现TiO₂从锐钛矿到不同比例的复合相(金红石型、锐钛矿型和板钛矿型)直至纯金红石相的转变,制备所需晶态结构的纳米TiO₂。所有样品进行了透射电镜与XRD表征,制备的纳米TiO₂及其TiO₂-SnO₂纳米复合材料颗粒小、分布均匀、分散性好,没有检测到SnO₂晶体的X-衍射特征峰。     

Fe基非晶和纳米晶合金晶化及电化学腐蚀行为

应用单辊甩带法制备非晶态Fe78Si13B9和Fe73.5Si13.5B9Nb3Cu1薄带,并以非晶晶化退火法制备出纳米晶Fe73.5Si13.5B9Nb3Cu1薄带.利用X射线衍射(XRD)仪和示差扫描量热计(DSC)对该非晶薄带的非晶特性及其晶化过程进行了研究.并用电化学极化曲线的方法和电化学阻抗技术研究了非晶态Fe78Si13B9和纳米晶Fe73.5Si13.5B9Nb3Cu1合金在1mol/LNaOH溶液里的电化学腐蚀行为,用SEM对极化测试后的试样形貌进行了观察;同时还研究了不同的热处理温度对材料结构及在1mol/LNaOH溶液里耐腐蚀性能的影响.结果表明,该非晶薄带的晶化过程分为两步;纳米晶比非晶合金的耐腐蚀性要好;且随着热处理温度的升高,非晶和纳米晶的耐腐蚀性能都得到提高.     

铒对Al-Ni-Y非晶合金微观结构及晶化行为的影响

采用单辊旋淬法制备了Al88Ni4Y8-xErx(x=0,2)非晶合金,用X射线衍射(XRD)、差示扫描量热(DSC)、 小角X射线散射(SAXS)等测试手段研究了Er元素的添加对Al-Ni-Y系非晶合金微观结构和非晶形成能力的影响. 结果表明:Er元素的添加使合金内部的微观颗粒结构的尺寸增大,导致原子扩散困难,阻碍了原子间的进一步成核与长大,延迟了非晶的晶化动力学行为,从而提高了该合金体系非晶形成能力和热稳定性.     

Y掺杂纳米TiO2的合成及晶型转变过程

溶胶-凝胶;锐钛型;金红石型;Y掺杂纳米TiO2的合成及晶型转变过程     

纳米晶Ni-Mo-Co合金镀层的结构与析氢行为

电沉积;结构;纳米晶Ni-Mo-Co合金镀层的结构与析氢行为     

纳米结构MnO2的水热合成、晶型及形貌演化

以水热合成方法制备了具有不同微观形貌的纳米结构MnO2, 并以X射线衍射(XRD), 扫描电镜(SEM)和X射线光电子能谱(XPS)等方法对其进行了表征. 跟踪考察了二氧化锰的晶型及微观形貌随水热反应时间的演变过程, 在Ostwald ripening机理作用下, MnO2晶型转化过程为γ-MnO2, α-MnO2和β-MnO2, 同时形貌由微米球转变为海胆结构、空心海胆结构和纳米线.     

Cu∶CdS纳米晶的绿色合成、结构及光谱性质研究

本文利用一种绿色合成工艺,采用巯基乙酸作为配体,在水溶液中成功合成了水溶性的Cu∶CdS纳米晶。利用X射线衍射分析(XRD)、傅里叶变换红外光谱(FT-IR)、场发射扫描电镜显微分析(FE-SEM)、能量色散X射线谱(EDX)、紫外可见(UV-Vis)吸收光谱对样品的晶体学性质、结构、形貌、成分、吸收光谱性质进行了系统的研究。着重研究了掺杂浓度对Cu∶CdS纳米晶的晶体学性质及吸收光谱的影响。结果表明:合成的Cu∶CdS纳米晶为立方相,通过谢乐公式估算的平均晶粒尺寸约为2 nm;随着掺杂浓度的增加,产物的晶胞参数也逐渐增大,表明Cu离子已经掺入到CdS纳米晶中,该发现与EDX结果相吻合。FT-IR红外光谱发现,配体巯基乙酸成功包覆在纳米晶的表面。UV-vis吸收谱表明,掺杂后的Cu∶CdS纳米晶的吸收峰向长波长方向移动。这种红移主要是Cu离子在CdS纳米晶中的掺杂而形成电子能级跃迁所致。     

微乳液法低温制备纳米金红石型二氧化钛的研究

以TiCl₄为原料、在十六烷基三甲基溴化铵/正己醇/水组成的微乳液体系中、在较低温度下,制备了球形、花状、捆绑丝和星形的金红石型二氧化钛纳米颗粒。研究了w值(水与CTAB物质的量之比)、反应物浓度、反应温度以及P值(正己醇与CTAB的物质的量之比)等因素对产品形貌的影响,并用TEM、XRD对产品进行了表征。     

Synthesis of Gray Ceramic Pigments with Rutile Structure from Alkoxides

In this study, V _x Ti_{1 – x} O₂ (0 x 0.20) rutile solid solutions have been synthesized from gels built from hydrolysis-condensation of V(IV) oxyacetilacetonate and Ti(IV) isopropoxide mixture (polymeric gel). These solid solutions are stable at high temperature (1200–1400°C) and into glazes. The colouration of the glazes together with the thermal stability of these rutile solid solutions indicates their potential usefulness as gray ceramic pigments. The results obtained are compared with those obtained from V₂O₅ and TiO₂ (anatase) mixtures (ceramic method). From alkoxides, noticeable change in coloration is obtained on glazes, when x < 0.10.     

Synthesis of novel nematic liquid crystals containing 3,3'-dimethyl-2,2'-bipyridyl

Liquid-crystalline 3,3′-dimethyl-2,2′-bipyridyl derivatives with long 4-(alkoxyphenyl)ethynyl (-C≡C-C₆H₄-OR) groups in the 5,5′-positions were synthesized by palladium-catalysed crosscoupling reactions. The compounds exhibit exclusively nematic behaviour; for example, the hexyl derivative showed a nematic phase over the temperature range 145.2–205.0°C. On increasing the length of the terminal chain, the transition temperatures were lowered; for example, the hexadecyl derivative was nematic in the range 117.0–126.8°C.     

新型偶氮苯类树状液晶的合成及表征

采用酯化反应合成端基含8个甲氧基偶氮苯介晶基元的新型树状液晶分子，并用元素分析、核磁共振(NMR)、红外光谱(IR)、差示扫描量热(DSC)和偏光显微镜(POM)表征树状液晶分子的结构与液晶性。结果表明：树枝状液晶分子在76℃表现出近晶态(S)向向列态(N)转变；在137℃表现出向列态向各相同性态转变；通过偏光显微镜观察到近晶态典型的焦锥织构，向列态典型的丝状织构。     

95 ℃水溶液体系中TiCl4溶胶水解法制备纯金红石纳米粉体(英)

Titanium dioxide (TiO2) nanoparticles of rutile phase were synthesized by hydrolysis of TiCl₄ at 95 ℃ in aqueous solution. The samples as prepared and calcined at 500 ℃ were characterized by XRD, TG-DTA and TEM. The sample as prepared was of imperfect rutile structure, and its morphology was rod-like with a diameter of 10～20 nm, a length of 20～80 nm and an aspect ratio of 2～4. The structure of the sample calcined at 500 ℃ was a perfect rutile one, and its morphology was rod-like with a diameter of 15～25 nm, a length of 25～105 nm and an aspect ratio of 2～4. These results indicate that calcination temperature has a positive effect on the structure and the size of rutile nanocrystals, and has no effect on the aspect ratio of rutile nanocrystal. A model for the formation mechnism of rutile nanocrystal in aqueous solution under hydrolysis conditions has been proposed.     

氩蒸气在球形固体颗粒上异质核化的分子动力学模拟

异质核化在大气中广泛存在, 但是其微观核化机理鲜为人知, 本文应用分子动力学方法模拟过热氩蒸气在纳米球形固体颗粒物上异质核化的动态特性, 讨论不同的冷却率对核化过程中系综温度、团簇分布、团簇大小以及核化速率的影响. 结果显示, 系综内蒸气的核化温度随着冷却率的增加而降低, 预先存在的球形固体颗粒在团簇的形成阶段起着重要的作用, 而且存在一个临界冷却率1.80×10^-9J·s^-1. 在该冷却率下, 在异质核化系综内均质核化出现, 并与异质核化共存, 但是异质核化在整个核化过程中仍然占主导地位.     

Sn-Pb合金颗粒异质成核及其冷却凝固行为预测

The Sn-5%Pb droplets with sizes of 150 and 185 μm were generated by Uniform Droplet Spray（UDS） under N2 atmosphere with 1. 36 μmol / L oxygen. The appearance of Sn-5%Pb droplets under the optical microscope showed that the droplets are uniform and spherical. The method employed non-adiabatic calorimetry to determine the nucleation point and undercooling of droplets. The fraction covered by oxide was calculated as a function of time and temperature. The model for heterogeneous nucleation catalyzed by oxidation on the droplet surface was developed,which was a reasonable expression of the heterogeneous nucleation and solidification behavior of Sn-Pb droplets. The CCT curves were computed using above experimental results under the heterogeneous surface nucleation of droplet. The same model can be applied to predict the heterogeneous nucleation behavior of the droplets for any type of cooling schedule. The calculation results are very reliable based on the experimental data.     

Synthesis of Liquid Crystalline Polymers with Side Chains

The present paper covers the synthesis and characterization of several intermediate products, monomer, and polymers. 3-{ 2-[ 4-( 4-Nitrophenylazo ) phenoxy] ethyloxycarbonyl} propanoyloxy (2-hydroxy) propyl acrylate (4) was prepared by the ring-opening reaction of glycidyl acrylate with the monoester of succinic acid (3). The polymers (5) with different molecular weights were prepared by the free-radical polymerization. The polymers (5) had liquid crystalline behavior without decomposition as revealed by DSC, optical microscope.     

Preparation of highly exfoliated epoxy/clay nanocomposites by clay grafted with liquid crystalline epoxy

Epoxy/clay nanocomposites with a high degree of exfoliation were achieved by intercalating liquid crystalline epoxy into clay intragallery as well as using a so-called ‘solution compounding’ process. In this process, clay modified was first treated with trichloromethane to form organoclay-trichloromethane suspension followed by liquid crystalline epoxy modification. The liquid crystalline epoxy grafted clay was then mixed extensively with epoxy to form epoxy/nanoclay composites. The mechanism of exfoliation was explored by monitoring the change of morphology of organoclay during each stage of processing with X-ray diffraction (XRD). The liquid crystalline epoxy grafted clay synthesised was characterised by fourier transform infrared spectroscopy (FT-IR) and polarising optical microscopy (POM). The clay platelets uniformly dispersed and highly exfoliated in the whole epoxy matrix were observed using transmission electron microscopy (TEM) and FT-IR imaging system. The epoxy nanocomposites were fabricated by incorporating different liquid crystalline epoxy grafted clay loading. The results revealed that the incorporation of liquid crystalline epoxy grafted clay resulted in a significant improvement in glass transition temperature (Tg) derived from dynamic mechanical analysis (DMA) and thermal stability measured by thermogravimetric analysis (TGA).