Synthesis and electrochemical properties of nanosized carbon-coated Li1−3x La x FePO4 composites

Nanosized carbon-coated Li_1−3x La _x FePO₄ composites were synthesized using a fast, easy, microwave assisted, room-temperature, solid-state method. A lanthanum precursor was used to improve the electronic conductivity of LiFePO₄. The particle structure of the as-synthesized samples was observed using transmission electron microscopy. The results indicated that a uniform and continuous carbon layer was formed on the surface of Li_1−3x La _x FePO₄ particles. Electrochemical techniques, such as cyclic voltammetry, charge/discharge test, and electrochemical impedance spectroscopy were used to investigate the electrochemical performance of the samples. The results of electrochemical measurements revealed that the carbon coating and lanthanum doping provided an initial discharge capacity of 145 mA h/g with excellent rate capacity and long cycling stability. These advantages, coupled with the low cost, the high thermal stability, and the environmental friendliness of the raw materials, render Li_1−3x La _x FePO₄/C composites attractive for practical and large-scale applications.     

Ca3(P x V1 − x O4)2: Eu3+ nanophosphor synthesis, controlled microstructure, and photoluminescence

In this paper, Eu³⁺-doped Ca₃(P _x V_{1 ? x} O₄)₂ (x = 0.1, 0.4, 0.7) nanophosphors were synthesized in the presence of sodium dodecyl benzene sulfonate (SDBS). The products present interesting and regular morphologies under the mild conditions. For Ca₃(P _x V_{1 ? x} O₄)₂: Eu³⁺, they have the similar phase and their morphologies vary with the content ratio of P to V. Furthermore, the luminescence behavior of Eu³⁺ has been investigated in this one kinds of matrices. In Ca₃(P _x V_{1 ? x} O₄)₂: Eu³⁺, the ⁵ D ₀-⁷ F ₂ emissions of Eu³⁺ were the strongest, indicating that the Eu³⁺ site is without inversion symmetry, the host compositions with different molar ratio of P to V have; great influence on the luminescent performance. Among those products, The value of I ₆₁₅/I ₅₉₃ for Eu³⁺ in Ca₃(P_0.7V_0.3O₄)₂ host lattice is the biggest. The substitution of PO ₄ ^3? for VO ₄ ^3? increase the ratio of surface Eu cations as well as the value of I ₆₁₅/I ₅₉₃ of Eu³⁺.     

Phosphates M 0.5(1 + x) 2+ Cr x Ti2 − x (PO4)3: Synthesis, structure, and catalytic properties

Complex phosphates of titanium, chromium, and metals(2+) of the general formula M_{0.5(1 + x} )Cr _x Ti_{2 ? x} (PO₄)₃ (M = Mg, Ca, Mn, Ni, Sr, Ba, and Pb) were synthesized. Their phase formation was studied by means of X-ray powder diffraction, electron probe microanalysis, differential thermal analysis, and IR spectroscopy. Individual phases and solid solutions crystallizing in kosnarite and langbeinite structure types were identified; their crystallographic parameters were calculated. The catalytic properties of phosphates Ca_{0.5(1 + x} )Cr _x Ti_{2 ? x} (PO₄)₃ in methanol conversion were studied.     

Synthesis and study of the properties of the solid solutions K2Y1−x Tb(Tm) x (MoO4)(PO4) and K2Y1−x Tm x (MoO4)(PO4)0.95(VO4)0.05

The solid solutions K₂Y_1?x Tb(Tm) _x (MoO₄)(PO₄) and K₂Y_1?x Tm _x (MoO₄)(PO₄)_0.95(VO₄)_0.05 were synthesized, which are isostructural and crystallize in the orthorhombic crystal system (space group Ibca). The luminescence intensity of the terbium-containing samples increases with increase in the terbium content. The thulium-containing samples are characterized by intense luminescence in the blue spectral region and concentration quenching of luminescence. The introduction of the vanadate anion adversely affects the luminescence intensity.     

Sol-gel formation and properties of nanocrystals of solid solutions Y1 − x Ca x FeO3

Nanopowders of ferrites Y_{1 ? x} Ca _x FeO₃ (x = 0.1, 0.2, and 0.3) were prepared by chemical coprecipitation of cations Y³⁺, Ca²⁺, and Fe³⁺ by an aqueous sodium carbonate solution. It was found that an increase in the calcium content leads to a decrease in the size of nanocrystals, the average size of which is 25–50 nm. Doping of yttrium orthoferrite with the doubly charged calcium ion enhances magnetization and decreases coercivity in samples.     

Synthesis and photoluminescent properties of benzodioxan β-aminoketones

A series of benzodioxan β-aminoketones with various substituents in their carbonyl and amino groups are prepared and their photoluminescence spectra are studied. Comparison of the luminescence spectra of β-amino-7-propionyl-1,4-bexodioxane and o-aminophenylethyl ketone demonstrates that the presence of an ethylendioxy fragment in the aromatic region of β-aminoketones increases the intensity of their luminescence in the blue region of the spectra. The photoluminescence intensity of the synthesized benzodioxane β-aminoketones depends on the nature of the substituent when carbonyl carbon is present and decreases in the sequence C₂H₅ > C₃H₇ > CH(CH₃)₂ > C₆H₅. Introduction of a substituent in the amino group of benzodioxane β-aminoketones reduces the intensity of luminescence.     

Modified low temperature solid state synthesis and photoluminescent properties of Y0.48Li1.5V1 ? x P x O4:Eu3+ (x = 0.2, 0.4, 0.6) nanophosphors

A modified low temperature solid state process has been proposed to systematically synthesize europium-doped yttrium phosphate-vanadates with general formula Y_0.48Li_1.5V_{1 ? x} P _x O₄:Eu³⁺ (x = 0.2, 0.4, 0.6). All the Y_0.48Li_1.5V_{1 ? x} P _x O₄:Eu³⁺ products were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The excitation and emission spectra were measured at room temperature. Y_0.48Li_1.5V_{1 ? x} P _x O₄:Eu³⁺ show the characteristic missions of Eu³⁺ (⁵ D ₀?⁷ F _{1, 2, 3, 4} transitions dominated by ⁵ D ₀?⁷ F ₂), intensities of the products were sensitive to the x value, and the x value had an obvious influence on the (⁵ D ₀?⁷ F ₂)/(⁵ D)₀?⁷ F ₁) intensity ratio of Eu³⁺. In addition, incorporation of Li⁺ ions in the phosphors reduce the amount of Y₂O₃, lower the cost of production, and cause a new phase Li₃VO₄.     

Synthesis and phase formation in M 0.5(1+x) 2+ FexTi2−x (PO4)3 phosphate series

New complex phosphates of titanium, iron, and alkaline-earth metals have been synthesized. X-ray powder diffraction, differential thermal analysis (DTA), and IR spectroscopy are used to study phase formation in the series of M_0.5(1+x)Fe_xTi_2?x (PO₄)₃ (M = Mg, Ca, Sr, Ba) phosphates. Individual compounds and solid solutions are found to crystallize in the NaZr₂(PO₄)₃ and K₂Mg₂(SO₄)₃ structure types. Their crystal parameters are calculated. CaFeTi(PO₄)₃ is studied using Mössbauer spectroscopy. Its structure is refined by the Rietveld method: space group $R\bar 3$ c, Z = 6, a = 8.5172(1), Å, c = 21.7739(4) Å, V = 1367.91(4) ų.     

Synthesis and properties of BaCe1−xYxO3−δ–BaWO4 composite protonic conductors

Barium cerate doped by trivalent rare earth metal ions is a potentially huge component of materials for electrochemical industry due to its high protonic conductivity. However, the poor chemical stability especially in the presence of CO₂, SO₂ or H₂O, resulting in decreasing the mechanical durability of obtained materials, limits their possible applications. The new approach towards stable ceramic protonic conductors with high electrical conductivity is presented. Thermal stability of yttrium doped (10 mol%) of BaCeO₃ was enhanced by forming the composite material BaCe_0.9Y_0.1O₃–BaWO₄ (10 mol% of BaWO₄). The synthesis was performed by solid-state reaction method. The detailed study of thermal decomposition of starting powders mixture was performed using thermogravimetry and differential thermal analysis (TG/DTA) techniques combined with Evolved Gas Analysis (EGA—mass spectrometry). Structure, phase composition and microstructure together with thermal stability of sintered materials were determined. The exposition tests were performed to characterise the stability of composites in carbon dioxide and water vapour-rich atmospheres. The samples were exposed to atmosphere containing CO₂/H₂O (7 % of CO₂ in air, 100 % RH) at temperature of 25 °C for 300 h. Thermal analysis supplied with mass spectrometry was applied to analyse the materials after the test. The results of this experiment showed better chemical resistance of composite material—BaCe_0.9Y_0.1O₃ with 10 mol% of BaWO₄ compared to single phase material.     

Synthesis and optical properties of quasi-2D CdS x Se1 − x nanoparticles

Colloidal 2D CdS _x Se_{1 ? x} nanoparticles have been synthesized by a solution method in octadecene using oleic acid as a stabilizer. Growth of quasi-2D nanoparticles has been promoted by the presence of cadmium acetate in the reaction mixture. The resulting nanoparticles are platelets with lateral sizes 20–30 nm. The absorption and luminescence spectra of these nanoparticles show narrow bands of lh-e and hh-e exciton transitions corresponding to 2D systems. The spectral position of the lowest energy hh-e transition monotonically changes within 382–461 nm with a change in the composition of nanoparticles. The observed absorption bands are broader than those for the individual CdSe and CdS nanoparticles. The suggested method makes it possible to vary the exciton band position for quasi-2D nanoparticles by changing their composition.     

Synthesis and characterization of a NASICON phase of variable composition Na1 − x Ni1 − x Sc1 + x (MoO4)3 (0 ≤ x ≤ 0.5)

Subsolidus phase ratios in the Na₂MoO₄-NiMoO₄-Sc₂(MoO₄)₃ system have been studied using X-ray diffraction, differential thermal analysis, and vibrational spectroscopy. A phase of variable composition Na_{1 ? x} Ni_{1 ? x} Sc_{1 + x} (MoO₄)₃ (0 ≤ x ≤ 0.5) having NASICON structure (space group \(R\bar 3c\) ) and a triple molybdate crystallizing in triclinic system (space group \(P\bar 1\) ) have been obtained. The high conductivity of Na_{1 ? x} Ni_{1 ? x} Sc_{1 + x} (MoO₄)₃ allows the phase of variable composition to be regarded as a promising sodiumion-conductive solid electrolyte.     

Electrical and electro-chemical characterisation of La0.99Fe1−x Ni x O3−δ perovskites

(LFN, 0<x<0.6) perovskites were synthesised by a solid-state route and were characterised by powder XRD, dilatometry, four-point DC conductivity measurements and electro-chemical impedance spectroscopy (EIS) on cone-shaped electrodes using a Ce_1.9Gd_0.1O_1.95 (CGO10) electrolyte. All the compounds were of single phase, and they belong to either the cubic or the hexagonal crystal system. The thermal expansion coefficient (TEC) was in the range 10.7*10⁻⁶ K⁻¹ to 13.4*10⁻⁶ K⁻¹, which continued to increase with increasing nickel content. The highest electronic conductivity was measured for the composition giving a value of 670 S/cm at 380 °C. The highest electro-chemical performance was measured for the composition giving an area specific resistance as low as 5.5 Ωcm² at 600 °C based on EIS measurements on a cone-shaped electrode. Composite cathodes made from and CGO10 revealed a rather low performance due to an un-optimised micro-structure.

---

Preparation of aqueous sols of Ce1 − x Gd x O2-δ, Y0.9Eu0.1VO4 and nanocomposites Ce1 − x Gd x O2-δ/Y0.9Eu0.1VO4 stabilized by polyacrylic acid

A method for the synthesis of stable aqueous sols of nanocrystalline solid solutions Ce_1?x Gd _x O_2-δ (x = 0.10, 0.15, 0.20) and Y_0.9Eu_0.1VO₄ and nanocomposites Ce_{1 ? x} Gd _x O_2-δ/Y_0.9Eu_0.1VO₄ stabilized by biocompatible low-molecular-weight polyacrylic acid was proposed. Polyacrylic acid was shown to be a promising matrix for the preparation of polyfunctional composite materials.     

Synthesis and Ionic Conductivity of LiZr2(VO4)x(PO4)3 – x

Russian Journal of Electrochemistry - Vanadate phosphates LiZr2(VO4)x(PO4)3 – x are synthesized by the sol-gel technique with subsequent annealing and studied using X-ray diffraction...     

Preparation and properties of highly conductive La1−x M x MnO3−y thin film showing magnetic effect from sol-gel process

The sol-gel synthesis of Sr-doped-LaMnO₃ thin film was investigated. The optimum condition was obtained when strontium, lanthanum and manganese nitrates were used as raw materials and diethylene or propylene glycol was used as solvent. An alumina plate was used as a substrate. The film thickness was about 0.2 m for one dip coating. The conductivity of Sr-substituted-LaMnO₃ increased with increasing Sr content and showed ferromagnetic properties. The conduction mechanism was a hopping conduction due to the small polaron. The metal-semiconductor transition at around room temperature was considered to be caused by the Jahn-Teller effect.     

Spectroscopic properties and luminescence concentration quenching of the Pr3+ ion in La1−xPrxOCl

Luminescence spectra ofLa_1−xPr_xOCl(0.01 ≤ x ≤ 0.3) were recorded at liquid helium and room temperature. From these spectra, the energy level diagram of Pr³⁺ in LaOCl was deduced. The decay times of the Pr³⁺ emission in La_1−xPr_xOCl were measured using a high-resolution dye laser system. The linear concentration quenching and exponential decay times are explained assuming cross relaxation and energy transfer between the Pr³⁺ ions.     

Synthesis of Calcium Phosphates by PO(OH)x(OBut)3−x and CaO2C2H4

In this work, an alkoxide solution route to synthesize Ca phosphates was developed. For the precursors, a CaO₂C₂H₄ solution was prepared by dissolving Ca metal powder into ethylene glycol, and a PO(OH)_x(OBut)_3–x solution was prepared by dissolving P₂O₅ inton -butanol under reflux conditions. In order to obtain a mixed solution of the two precursors, acetic acid was used as an additive. The experimental results show that (1) -2CaO · P₂O₅, -3CaO · P₂O₅, and hydroxyapatite can be easily synthesized by converting the corresponding mixed solutions to powder products in a hot plate, and calcining the as prepared products at 1100°C; (2) acetic acid behaves as a good agent for controlling the reactions between the two precursors by modifying the CaO₂C₂H₄ species in solution and decreasing the reactivity of the PO(OH)_x(OBut)_3–x species.