Human plasma protein adsorption onto dextranized surfaces: a two-dimensional electrophoresis and mass spectrometry study

Protein adsorption is fundamental to thrombosis and to the design of biocompatible materials. We report a two-dimensional electrophoresis and mass spectrometry study to characterize multiple human plasma proteins adsorbed onto four different types of model surfaces: silicon oxide, dextranized silicon, polyurethane and dextranized polyurethane. Dextran was grafted onto the surfaces of silicon and polyurethane to mimic the blood-contacting endothelial cell glycocalyx surface. Surface topography and hydrophobicity/hydrophilicity were determined and analyzed using atomic force microscopy and water contact angle measurements, respectively. Using two-dimensional electrophoresis, we show that, relative to the unmodified surfaces, dextranization significantly inhibits the adsorption of several human plasma proteins including IGHG1 protein, fibrinogen, haptoglobin, Apo A-IV, Apo A-I, immunoglobulin, serum retinal-binding protein and truncated serum albumin. We further demonstrate the selectivity of plasma protein adsorbed onto the different functionalized surfaces and the potential to control and manipulate proteins adsorption on the surfaces of medical devices, implants and microfluidic devices. This result shows that adsorption experiments using a single protein or a binary mixture of proteins are consistent with competitive protein adsorption studies. In summary, these studies indicate that coating blood-contacting biomedical applications with dextran is an effective route to reduce thrombo-inflammatory responses and to surface-direct biological activities.     

Single-particle electrophoresis for studying the adsorption of cationic polymers onto anionic particles

Understanding the adsorption of polymers onto particles is crucial for many technological and biomedical applications. Even though polymer adsorption on particles is a dynamic process, most experimental techniques can only study the adsorption indirectly, in equilibrium and on the ensemble level. New analysis methods are required to overcome these limitations. We investigated the use of single-particle electrophoresis to study the adsorption kinetics of cationic polymers onto anionic particles and compared the resulting data to a theoretical model. In this approach, the electrophoretic mobility of single polystyrene (PS) particles, exposed to different concentrations of poly(2-guanidinoethyl methacrylate), was measured as a function of time. The polymer adsorption leads to an electrophoretic mobility change of the PS particle over time, from the initial negative value to a positive value at equilibrium. By fitting the kinetics data to the Langmuir model, the adsorption rate, desorption rate and equilibrium constant were determined. Finally, the adsorption kinetics of several other polymers was investigated. This showed that the presented technique enables direct analysis and comparison of the kinetics of polymer adsorption on the single-particle level.     

Polymer adsorption onto random planar surfaces: interplay of polymer and surface correlations

We study the adsorption of homogeneous or heterogeneous polymers onto heterogeneous planar surfaces with exponentially decaying site-site correlations, using a variational reference system approach. As a main result, we derive simple equations for the adsorption-desorption transition line. We show that it is preferable to have a small amount of strongly adsorbing sites or monomers rather than a greater amount of weakly adsorbing ones. The results are discussed with respect to their implications for the physics of molecular recognition.     

Use of optical tweezers for colloid science

A space-borne optical tweezer apparatus for use with colloidal crystallization experiments has been characterized. The trapping force has been measured as a function of index mismatch between colloidal microspheres and the surrounding fluid and as a function of particle size. This work also presents a method to determine the refractive index of a colloidal microsphere, which is then used to calculate the applied trapping force for the case of an arbitrary background fluid. This is useful for work with dense colloidal suspensions when the usual (e.g., Stokes flow) trap force measurement methods do not apply, as well as microrheological studies of complex soft matter.     

Paraquat adsorption onto clays and organoclays from aqueous solution

Clays were compared with organoclays for the sorption of paraquat from aqueous solution. Sepiolite (S), bentonite (B), and illite (I) were used as clay samples. Organoclays were prepared by the modification of the clays with nonyl- and dodecylammonium chlorides, denoted as NS, DS, NB, DB, NI, and DI, respectively. Specific surface area and pore size distribution of the samples were determined by N2 adsorption-desorption at 77 K using the BET method. X-ray powder diffraction analysis of the samples was used to determine the effects of modifying agents on the layer structure of the clays. In the adsorption experiments, C(m) values increased from 0.038 mmol/g for DS to 0.223 mmol/g for NI. Kd0.3 values ranged from 0.177 for DS to 0.843 for NI. The adsorption data indicated that illite and NI are the most effective adsorbents among these clays and organoclay samples, respectively.     

Retrieval of the complex refractive index of aerosol droplets from optical tweezers measurements

The cavity enhanced Raman scattering spectrum recorded from an aerosol droplet provides a unique fingerprint of droplet radius and refractive index, assuming that the droplet is homogeneous in composition. Aerosol optical tweezers are used in this study to capture a single droplet and a Raman fingerprint is recorded using the trapping laser as the source for the Raman excitation. We report here the retrieval of the real part of the refractive index with an uncertainty of ± 0.0012 (better than ± 0.11%), simultaneously measuring the size of the micrometre sized liquid droplet with a precision of better than 1 nm (< ± 0.05% error). In addition, the equilibrium size of the droplet is shown to depend on the laser irradiance due to optical absorption, which elevates the droplet temperature above that of the ambient gas phase. Modulation of the illuminating laser power leads to a modulation in droplet size as the temperature elevation is altered. By measuring induced size changes of <1 nm, we show that the imaginary part of the refractive index can be retrieved even when less than 10 × 10(-9) with an accuracy of better than ± 0.5 × 10(-9). The combination of these measurements allows the complex refractive index of a droplet to be retrieved with high accuracy, with the possibility of making extremely sensitive optical absorption measurements on aerosol samples and the testing of frequently used mixing rules for treating aerosol optical properties. More generally, this method provides an extremely sensitive approach for measuring refractive indices, particularly under solute supersaturation conditions that cannot be accessed by simple bulk-phase measurements.     

Monolayer adsorption onto triangular lattice

A simple model of monolayer adsorption on homogeneous solid surfaces of triangular symmetry is presented. This model takes into account the effects of three-fold positional degeneracy of adsorption sites and of partial mobility of adsorbed layer. The model predicts phase transitions in adsorbed layers analogous to those found in experimental systems.

---

Einschichtadsorption auf triangularem Gitter

Zusammenfassung Es wird ein einfaches Modell für die Adsorption einer Schicht auf einer homogenen festen Oberfläche von triangularer Symmetrie präsentiert. Das Modell berücksichtigt den Effekt der dreifachen Positionsdegenierung von Adsorptionsstellen und auch den Einfluß der partiellen Mobilität der adsorbierten Schicht. Das Modell erlaubt die Voraussage von Phasenübergängen in der adsorbierten Schicht, die in Analogie zu experimentellen Systemen stehen.

     

Surfactant adsorption onto cellulose surfaces

The adsorption of the cationic surfactant, hexadecyl trimethyl ammonium bromide, C16TAB, onto model cellulose surfaces, prepared by Langmuir-Blodgett deposition as thin films, has been investigated by neutron reflectivity. Comparison between the adsorption of C16TAB onto hydrophilic silica, a hydrophobic cellulose surface, and a regenerated (hydrophilic) cellulose surface is made. Adsorption onto the hydrophilic silica and onto the hydrophilic cellulose surfaces is similar, and is in the form of surface aggregates. In contrast, the adsorption onto the hydrophobic cellulose surface is lower and in the form of a monolayer. The impact of the surfactant adsorption and the in situ surface regeneration on the structure of the cellulose thin films and the nature of solvent penetration into the cellulose films are also investigated. For the hydrophobic cellulose surface, intermixing between the cellulose and surfactant occurs, whereas there is little penetration of surfactant into the hydrophilic cellulose surface. Measurements show that solvent exchange between the partially hydrated cellulose film and the solution is slow on the time scale of the measurements.     

Comparative studies for the determination of uranyl ion adsorption onto Interpenetrating Polymer Networks (IPNs)

The adsorption of uranyl ions from aqueous solutions was studied by using three different measurement techniques. Results obtained by γ-spectrometry, UV-visible spectrophotometry and gravimetry have been compared. It was observed that the results obtained by γ-spectrometric and gravimetric methods were in good agreement and consequently they gave similar deviation error values, whereas the error values for UV-spectrophotometric method were higher than these values. As a conclusion, γ-spectrometric method was found to be more suitable for analysis of uranium in solid and aqueous phases and may be preferred over the UV-spectrophotometric method.     

A direct method for measuring adsorption from solution onto solids

A direct method of measuring solution adsorption onto a solid has been developed. The results are exactly the same as those given by the conventional method of measuring the change in composition of the solution upon contacting the adsorbent. The development is cast in the terms of Gibbsian surface concepts, from which the correct thermodynamic significance of adsorption measurements made by directly analyzing material adsorbed on the solid can be understood. The method was tested for the adsorption of Na-Laurate and n-hexanol from aqueous and n-decane solutions, and typical isotherms are presented. The various realized and potential advantages of the method are discussed. The most important of these are the ability to measure adsorption in complex systems with a negligible change in solution composition, and the possibility of ameliorating in certain situations some of the difficulties in measuring adsorption at high concentrations or on low surface area solids.     

Incorporation of a molecular hinge into molecular tweezers by using tandem cycloadditions onto 5,6-dimethylenenorbornene

Site-selective 1,3-dipolar coupling at the norbornene pi-bond of 5,6-dimethylenenorbornene 1 yields cycloadducts with an end-fused 1,3-diene system which have been reacted with N=N (or C=C) dienophiles to produce ribbon molecules, in which the internal diazacyclohexene (or cyclohexene) subunits are capable of acting as conformational hinges. Direct coupling of 5,6-dimethylenenorbornene with 1,3,4-oxadiazoles or dual coupling with bis(cyclobutene epoxides) afforded bis(1,3-dienes) that diastereoselectively react with dienophiles to produce new, conformationally mobile, molecular tweezers.     

Microfluidic sorting of arbitrary cells with dynamic optical tweezers

Optical gradient forces generated by fast steerable optical tweezers are highly effective for sorting small populations of cells in a lab-on-a-chip environment. The presented system can sort a broad range of different biological specimens by an automated optimisation of the tweezer path and velocity profile. The optimal grab positions for subsequent trap and cell displacements are estimated from the intensity of the bright field image, which is derived theoretically and proven experimentally. We exhibit rapid displacements of 2 μm small mitochondria, yeast cells, rod-shaped bacteria and 30 μm large protoplasts. Reliable sorting of yeast cells in a microfluidic chamber by both morphological criteria and by fluorescence emission is demonstrated.     

Microrheology with optical tweezers: peaks & troughs

Since their first appearance in the 1970s, optical tweezers have been successfully exploited for a variety of applications throughout the natural sciences, revolutionising the field of microsensing. However, when adopted for microrheology studies, there exist some peaks and troughs on their modus operandi and data analysis that I wish to address and possibly iron out, providing a guide to future rheological studies from a microscopic perspective.     

Sodium stearate adsorption onto titania pigment

The interaction of sodium stearate with titania pigment particles from aqueous suspension has been investigated using thermal analysis and infrared spectroscopy combined with electrochemical studies. Thermogravimetric analysis (TGA) was used both to determine the adsorption isotherm and to investigate the interaction behavior. Monolayer coverage is determined to be 0.95 mg/m(2); however, unlike the case with organic solvents, multilayer adsorption occurs. Diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, combined with TGA, revealed that the surface monolayer is chemically bound. DRIFT spectroscopic data also indicated that the stearate bridged across two aluminum atoms. Subsequent stearate layers were physisorbed to the stearate monolayer and were readily removed with acetone washing.     

Characterization of water adsorption onto carbonaceous materials produced from food wastes

The recycling of organic wastes has become very important and the development of technology for recycling organic wastes needs to sustain industrial development. In this study, techniques for producing carbonaceous materials from organic wastes are described and water adsorption is characterized. The organic wastes used are coffee grounds and oolong tea leaves carbonized at 673 to 1073 K. The iodine adsorption capacity of the carbonaceous materials increased with increased carbonization temperature. The amount of water adsorbed onto the carbonization materials produced from oolong tea leaves at 873 K for 2 h was the highest. The Freundlich constant 1/n and the differential heat of adsorption of the carbonaceous materials produced from oolong tea leaves were greater than that of the carbonaceous materials produced from coffee grounds. The ability to humidity control can be estimated by the difference between the amount of water adsorbed relative pressure 0.90 and that at relative pressure 0.55. The ability to humidity control was the greatest for the carbonaceous materials produced from the oolong tea leaves at 873 K for 2 h and did not depend upon the adsorption temperature. These results indicated that the carbonaceous materials produced from oolong tea leaves at 873 K for 2 h could have more humidity control.     

Fibronectin adsorption onto polyelectrolyte multilayer films

The Layer-by-layer deposition of positively and negatively charged macromolecular species is an ideal method for constructing thin films incorporating biological molecules. We investigate the adsorption of fibronectin onto polyelectrolyte multilayer (PEM) films using optical waveguide lightmode spectroscopy (OWLS) and atomic force microscopy (AFM). PEM films are formed by adsorption onto Si(Ti)O2 from alternately introduced flowing solutions of anionic poly(sodium 4-styrenesulfonate) (PSS) and cationic poly(allylamine hydrochloride) (PAH). Using OWLS, we find the initial rate and overall extent offibronectin adsorption to be greatest on PEM films terminated with a PAH layer. The polarizability density of the adsorbed protein layer, as measured by its refractive index, is virtually identical on both PAH- and PSS-terminated films; the higher adsorbed density on the PAH-terminated film is due to an adsorbed layer of roughly twice the thickness. The binding of monoclonal antibodies specific to the protein's cell binding site is considerably enhanced to fibronectin adsorbed to the PSS layer, indicating a more accessible adsorbed layer. With increased salt concentration, we find thicker PEM films but considerably thinner adsorbed fibronectin layers, owing to increased electrostatic screening. Using AFM, we find adsorbed fibronectin layers to contain clusters; these are more numerous and symmetric on the PSS-terminated film. By considering the electrostatic binding of a segmental model fibronectin molecule, we propose a picture of fibronectin adsorbed primarily in an end-on-oriented monolayer on a PAH-terminated film and as clusters plus side-on-oriented isolated molecules onto a PSS-terminated film.     

Arsenic adsorption onto hematite and goethite

Surface complexation reactions on mineral affect the fate and the transport of arsenic in environmental systems and the global cycle of this element. In this work, the sorption of As(V) on two commercial iron oxides (hematite and goethite) was studied as a function of different physico-chemical parameters such as pH and ionic strength. The main trend observed in the variation of the arsenic sorbed with the pH is a strong retention in acidic pH and the decrease of the sorption on both sorbents at alkaline pH values. The sorption experiments for these iron oxides show that there is no effect of the ionic strength on arsenate adsorption suggesting the formation of an inner sphere surface complex. At pH values corresponding to natural pH water, both hematite and goethite are able to adsorb more than 80% of arsenic, whatever the initial concentration may be. The iron oxides used in this work should be suitable candidates as sorbents for As(V) removal technologies.