Growth of β-MnO2 films on TiO2(110) by oxygen plasma assisted molecular beam epitaxy

We have used oxygen plasma assisted MBE to grow epitaxial films of pyrolusite (β-MnO₂) on TiO₂(110) for thicknesses of one to six bilayers (BL). We define a bilayer to be a layer of Mn and lattice O and an adjacent layer of bridging O within the rutile structure. The resulting surfaces have been characterized in situ by reflection high-energy electron diffraction, low-energy electron diffraction, X-ray photoelectron spectroscopy and diffraction, and atomic force microscopy. Well-ordered, pseudomorphic overlayers form for substrate temperatures between 400 and 500°C. Mn–Ti intermixing occurs over the time scale of film growth (1 BL/min) for substrate temperatures in excess of 500°C. Films grown at 400–500°C exhibit island growth, whereas intermixed films grown at temperatures of 500–600°C are more laminar. 1 BL films grown at 450°C are more laminar than multilayer films grown at the same temperature, and form a well-ordered surface cation layer of Mn on the rutile structure with at most 10% indiffusion to the second cation layer.     

Temperature- and coverage-dependent evolution of the Au/Pd(1 1 0) surface structure

The morphology and the atomic scale structure of thin gold films (up to 2.5 ML) on Pd(1 1 0) were studied by means of scanning tunneling microscopy and surface X-ray diffraction. At room temperature the films exhibit a multilayer growth mode accompanied by the formation of highly anisotropic islands. Annealing above 500 K significantly increases the smoothness of the gold films, which are in registry with the substrate. Above a critical threshold of two monolayers a (1 × 2) missing-row reconstructed film is found. This reconstructed surface is well ordered after annealing at temperatures above 580 K. The specific gold film morphology is envisaged as a way to relax the strain caused by the mismatch between gold and palladium.     

Structural and compositional mapping of a phase-separated Langmuir–Blodgett monolayer by X-ray photoelectron emission microscopy

The structure and composition of phase-separated Langmuir–Blodgett monolayer films comprised of mixtures of arachidic acid (C₁₉H₃₉COOH) and perfluorotetradecanoic acid (C₁₃F₂₇COOH) were characterized using a combination of X-ray photoelectron emission microscopy (X-PEEM), secondary electron emission microscopy (SEEM) and atomic force microscopy (AFM). X-PEEM provides high lateral spatial resolution and is directly sensitive to the elemental and chemical (functional group) composition of these ultrathin films through the chemical sensitivity of NEXAFS spectroscopy; AFM provides high-resolution imaging, both in terms of lateral and vertical (height) film topography. SEEM provides additional structural and electronic information through work function and electron scattering effects. The combination is used for chemical mapping of the phase-separated domains in the monolayer film. Our results directly confirm previous AFM measurements that suggested that the discontinuous domains are enriched in arachidic acid, whereas the surrounding continuous domain is a mixture of both arachidic acid and perfluorotetradecanoic acid.     

Morphology of compressed dipalmitoyl phosphatidylcholine monolayers investigated by atomic force microscopy

The effectiveness of a substitute of natural lung surfactants on replacement therapy strongly depends on the stability of the monolayer of those substitute molecules. An atomic force microscope is utilized to investigate the microstructure of the films of the major components of natural lung surfactants, dipalmitoyl phosphatidylcholine—DPPC, which are transferred to mica substrates by the Langmuir-Blodgett film technique. A concave deformation structure was first observed for DPPC in solid phase. The depth of the concave domain was about 6 nm and was remarkably uniform. For a collapsed DPPC monolayer, the surface film consists of a granular convex multilayer structure and a disc-like concave structure. Dynamic cyclic compression-expansion experiments indicate that the formation of the concave domain is a reversible process while the process for convex multilayer formation is irreversible. This gives direct evidence that convex grain is the collapsed structure of DPPC monolayer and the concave shallow disc corresponds to the elastic deformation of a DPPC solid film. Results of atomic force microscopy indicate that the nucleation and growth model instead of the fracture model can better describe the collapse behavior of a DPPC monolayer.     

Deposition of ZnO multilayer on LiNbO3 single crystals by DC-magnetron sputtering

Zinc oxide (ZnO) thin films were deposited on LiNbO₃ (LN) single crystals with 200 nm thicknesses by three different ways, where coating of zinc (Zn) film was followed by thermal oxidation for four, two, and one steps with 50, 100, and 200 nm thicknesses repeatedly. Sample, which was produced at 4-step of deposition and oxidation of Zn layer, showed high transmittance and low structural defect due to a lower photoluminescence intensity and Urbach energy. Average grain size in X-ray diffraction (XRD), scanning electron microscopy (SEM) micrograph, and atomic force microscopy (AFM) images for multilayer of ZnO was lower than monolayer of ZnO thin films. Applying multilayer coating technique leads to decrease of surface roughness and scattering on light on surface and fabrication of LiNbO₃ waveguides with lower optical loss.     

Effect of freon flow rate on tin oxide thin films deposited by chemical vapor deposition

High quality fluorine-doped tin oxide (SnO₂:F) films on glass substrates were been prepared using chemical vapor deposition (CVD) method. The electrical properties, surface morphologies, structural properties and optical properties of the films were studied by varying the freon flow rates. The structure was analyzed by X-ray diffraction (XRD). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to study the morphology. Energy-dispersive spectroscopy (EDS) was conducted to understand the surface fluorine composition of the film. The results showed that crystalline structure of the film had a have cassiterite-like diffraction patterns with a preferred orientation of (1 1 0). Surface roughness was evaluated by atomic force microscopy, characterized by root mean square (RMS) and average value (Ra). The SnO₂:F resistivity decreased as the freon flow rate increased. The films had a uniform thickness and a transmittance of 80–90% within the visible region of the spectrum.     

Effects of poly(ethylene glycol) on electrical conductivity of poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) film

A series of poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonic acid) composite thin films with prescribed concentrations of poly(ethylene glycol) were prepared. The PEDOT–PSS pristine film and PEDOT–PSS/PEG films were studied using four-probe method, photoelectron spectroscopy and atomic force microscopy. The electrical conductivity of PEDOT–PSS/PEG hybrid films was found to be enhanced compared to the PEDOT–PSS pristine film, depending on the PEG concentration and molecular weight. XPS analysis and AFM results showed that PEG induces the phase separation between the PEDOT–PSS conducting particles and the excessive PSSNa shell. Simultaneously PEG may form hydrogen bond with sulfonic groups of PSSH, and hence weaken the electrostatic interactions between PEDOT cationic chains and PSS anionic chains. These resulted in the creation of a better conduction pathway among PEDOT–PSS particles, attributed to the improvement of conductivity.     

Effect of local curvature of internal and external interfaces on mass transfer responsible for thin film degradation

The degradation of thin films on thermal annealing was studied by atomic force and scanning electron microscopy. Main factors that govern high-temperature mass transfer in the multilayer structures were disclosed. It is shown that local curvature of internal and external interfaces is a driving force in the mass transfer responsible for thin film degradation, redistribution of alloying elements, and formation of silicides.     

Microstructures and tribological properties of CrN/ZrN nanoscale multilayer coatings

Nanoscale multilayer CrN/ZrN coatings with bilayer thicknesses ranging from 11.7 to 66.7 nm were prepared by reactive magnetron sputtering techniques. The structure of the thin films was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). X-ray diffraction results showed that CrN individual layers presented a <1 1 1> preferred orientation in the multilayer coatings. The diffraction peaks of CrN shifted continuously to low diffraction angle with decreasing bilayer thickness. TEM observations showed that the multilayer did not form a superlattice structure instead of the coexistence of nanocrystalline CrN and ZrN layers. Columnar growth for all the coatings was observed by cross-sectional SEM. Nanoindentation tests showed that the multilayer coatings had almost a constant nanohardness of 29 GPa in spite of the variations of bilayer thickness. Pin-on-disk tests indicated that both the friction coefficients and wear rates increased when decreasing bilayer thickness. However, in comparison with the monolayer coating, the multilayer coatings exhibited excellent wear resistance.     

Nanoparticle Distribution in Three‐Layer Polymer–Nanoparticle Composite Films: Comparison of Experiment and Theory

The distribution of hydrophobic nanoparticles deposited on a hydrophilic polymer film is investigated by scanning electron microscopy, transmission electron microscopy, and atomic force microscopy before and after spin‐coating a polymer solution on the particle film and drying it at room temperature. Various polymers and solvents are used. To reach equilibrium, all investigated systems are annealed additionally above the glass transition temperature (T_g) of the polymers. The compatibility of the interacting components is estimated by calculating their surface energy, solubility, and mutual interaction parameters. The experimental results show a redistribution of the particles on both interfaces of the polymer film. This corresponds to the calculated immiscibility of particles and polymers. The distribution of the nanoparticles at the interfaces is related mainly to the vapor pressure of the solvent, that is, kinetic effects during spin‐coating. Only minor contributions result from surface energy, solubility, and interaction parameters.     

Experimental research of laser-induced damage of the monolayer ZrO2 PVD and sol–gel films

Monolayer zirconia physical vapor deposition (PVD) and sol–gel films on K9 glass substrates were prepared by electron beam evaporation and spin coating methods, respectively. The laser-induced damage threshold (LIDT) of each film was measured. Properties of the films were analyzed using Stanford photo-thermal solutions (SPTS), ellipsometry, atomic force microscopy (AFM) and optical microscopy to study the damage mechanism of films under laser irradiation. The experimental results showed that, compared with the monolayer zirconia sol–gel film, the monolayer zirconia PVD film had larger absorption and smaller porous ratio, and that it had smaller LIDT. The different damage morphologies of films were influenced by their different absorption and microstructure characteristics. The zirconia sol–gel film is more suitable for applications involving high-power lasers.     

A rapid approach to reproducible, atomically flat gold films on mica

A simple and reproducible method for the preparation of gold films on mica with large (typically 0.8-1.0 μm) atomically flat (1 1 1) terraces is described. The procedure involves thin gold film evaporation onto freshly cleaved mica substrates, followed by 1 min annealing at 650 °C under nitrogen. The annealed gold surfaces are compared to those of freshly evaporated gold films on mica using cyclic voltammetry and atomic force microscopy. Our results favorably compare to other published annealing techniques, with minimal equipment and time necessary to reproducibly obtain atomically flat gold terraces.     

Morphological characteristics of amorphous Ge2Sb2Te5 films after a single femtosecond laser pulse irradiation

The morphology of materials resulting from laser irradiation of the single-layer and the multilayer amorphous Ge₂Sb₂Te₅ films using 120 fs pulses at 800 nm was observed using scanning electron microscopy and atomic force microscopy. For the single-layer film, the center of the irradiated spot is depression and the border is protrusion, however, for the multilayer film, the center morphology changes from a depression to a protrusion as the increase of the energy. The crystallization threshold fluence of the single-layer and the multilayer film is 22 and 23 mJ/cm², respectively.     

Preliminary investigations on the antibacterial activity of zinc oxide nanostructures

We have fabricated electroactive multilayer thin films containing ferritin protein cages. The multilayer thin films were prepared on a solid substrate by the alternate electrostatic adsorption of (apo)ferritin and poly(N-isopropylacrylamide-co-2-carboxyisopropylacrylamide) (NIPAAm-co-CIPAAm) in pH 3.5 acetate buffer solution. The assembly process was monitored using a quartz crystal microbalance. The (apo)ferritin/poly(NIPAAm-co-CIPAAm) multilayer thin films were then cross-linked using a water-soluble carbodiimide, 1-[3-(dimethylamino)propyl]-3-ethylcarbodiimide. The cross-linked films were stable under a variety of conditions. The surface morphology and thickness of the multilayer thin films were characterized by atomic force microscopy, and the ferritin iron cores were observed by scanning electron microscopy to confirm the assembly mechanism. Cyclic voltammetry measurements showed different electrochemical properties for the cross-linked ferritin and apoferritin multilayer thin films, and the effect of stability of the multilayer film on its electrochemical properties was also examined. Our method for constructing multilayer films containing protein cages is expected to be useful in building more complex functional inorganic nanostructures.     

Direct measurement of electron transport features in cytochrome c via V–I characteristics of STM currents

The morphology of and electron tunneling through single and cluster cytochrome c molecules deposited on self-assembled dodecanthiol monolayer film on a gold substrate have been studied experimentally using scanning tunneling microscopy (STM) and scanning tunneling spectroscopy. STM images of a single cytochrome c molecule revealed a globular structure with a diameter of 4 nm and height of 1.5 nm. A spectroscopic study obtained by recording tunneling current–bias voltage (V–I) curves revealed that the STM current increases stepwise at asymmetric threshold sample bias voltages of +100 mV and –200 mV.     

Hybrid Nanoparticle Film Material

A new hybrid material consisting of a nanoparticle film on a flexible, porous substrate is formed. The hybrid nanoparticle films are non-redispersable in solvents, yet remain porous and flexible. Visually, the hybrid films are highly reflective and metallic gold in appearance. However, the electronic properties of the films are characteristic for materials made from separate, non-sintered nanoparticles. Films of large area (several tens of cm²) and several microns in thickness can be formed. The method of formation is based on cross-linking gold nanoparticles using alkane-dithiols followed by filtration onto nanoporous supports. The films were characterized by transmission electron microscopy, atomic force microscopy and resistance measurements. The effect of the ratio of alkane-dithiol cross-linker to gold nanoparticles on the resistance of the nanoparticle films was also studied.     

Nonpolar a-plane GaN grown on r-plane sapphire using multilayer AlN buffer by metalorganic chemical vapor deposition

Mirror-like and pit-free non-polar a-plane (1 1 −2 0) GaN films are grown on r-plane (1 −1 0 2) sapphire substrates using metalorganic chemical vapor deposition (MOCVD) with multilayer high-low-high temperature AlN buffer layers. The buffer layer structure and film quality are essential to the growth of a flat, crack-free and pit-free a-plane GaN film. The multilayer AlN buffer structure includes a thin low-temperature-deposited AlN (LT-AlN) layer inserted into the high-temperature-deposited AlN (HT-AlN) layer. The results demonstrate that the multilayer AlN buffer structure can improve the surface morphology of the upper a-plane GaN film. The grown multilayer AlN buffer structure reduced the tensile stress on the AlN buffer layers and increased the compressive stress on the a-plane GaN film. The multilayer AlN buffer structure markedly improves the surface morphology of the a-plane GaN film, as revealed by scanning electron microscopy. The effects of various growth V/III ratios was investigated to obtain a-plane GaN films with better surface morphology. The mean roughness of the surface was 1.02 nm, as revealed by atomic force microscopy. Accordingly, the multilayer AlN buffer structure improves the surface morphology and facilitates the complete coalescence of the a-plane GaN layer.     

Tribological properties of chemically bonded polyimide films on silicon with polyglycidyl methacrylate brush as adhesive layer

Polyimide thin films, which possess good stability and film uniformity, are successfully fabricated on single crystal silicon wafers coated with a thin polymer brush by suface-initiated polymerization (SIP) as an adhesive layer. The growth kinetic of polyglycidyl methacrylate (PGMA) brush was studied by the means of ellipsometry. The nano-scale morphology and chemical composition of PGMA brush and polyimide film were studied with atomic force microscopy (AFM), Fourier transform infrared spectrum (FT-IR), and X-ray photoelectron spectroscopy (XPS). The tribological behaviors of the thin films sliding against AISI-52100 steel ball were examined on a static-dynamic friction precision measurement apparatus and UMT-2MT tribometer. The worn surface of the polyimide thin films was investigated with scanning electron microscopy (SEM). The results indicated that the chemically bonded polyimide films exhibited better friction reduction and antiwear behavior compared to the polymide films on bare silicon surface. At a load of 0.5 N and sliding speed of 20 mm s⁻¹, the durability life of the polyimide thin films is over 25,000 sliding cycles and the friction coefficient is about 0.08.     

Fabrication and performance characterization of Al/Ni multilayer energetic films

Al/Ni multilayer bridge films, which were composed of alternate Al and Ni layers with bilayer thicknesses of 50, 100 and 200 nm, were prepared by RF magnetron sputtering. In each bilayer, the thickness ratio of Al to Ni was maintained at 3:2 to obtain an overall 1:1 atomic composition. The total thickness of Al/Ni multilayer films was 2 μm. XRD measurements show that the compound of AlNi is the final product of the exothermic reactions. DSC curves show that the values of heat release in Al/Ni multilayer films with bilayer thicknesses of 50, 100 and 200 nm are 389.43, 396.69 and 409.92 J?g^?1, respectively. The temperatures of Al/Ni multilayer films were obviously higher than those of Al bridge film and Ni bridge film. Al/Ni multilayer films with modulation of 50 nm had the highest electrical explosion temperature of 7000 K. The exothermic reaction in Al/Ni multilayer films leads to a more intense electric explosion. Al/Ni multilayer bridge films with modulation period of 50 nm explode more rapidly and intensely than other bridge films because decreasing the bilayer thickness results in an increased reaction velocity.     

不同工作压强下辉光放电聚合物薄膜的表面形貌与光学性质

利用低压等离子体聚合技术在不同工作压强下制备了辉光放电聚合物(GDP)薄膜。利用原子力显微镜、傅里叶红外光谱仪、元素分析仪和紫外-可见光谱仪对GDP薄膜的表面形貌、化学结构、碳氢原子数比以及光学性质进行了表征。分析了工作压强对薄膜表面形貌、化学结构、碳氢原子比和光学性质的影响以及相互关系。结果表明:GDP薄膜的表面形貌随工作压强的增大而变得平整光滑,均方根粗糙度逐渐减小。随工作压强增大,GDP薄膜的化学结构的相互交联化程度减弱,C=C双键含量不断减小,碳氢原子数比不断减小,氢元素含量逐渐增大,薄膜的光学透过率截止波长发生"蓝移",光学间隙不断增加。