Simultaneous determination of trace amounts of cadmium, nickel and cobalt in water samples by adsorptive voltammetry using ammonium 2-amino-cyclopentene dithiocarboxylate as a chelating agent

This paper reports the use of an adsorptive voltammetric technique for the simultaneous detection of Cd(II), Ni(II) and Co(II) using ammonium 2-amino-cyclopente dithiocarboxylate as a selective complexing agent. Scans containing three resolved peaks corresponding to these metals were obtained in synthetic and real samples. The reduction current peaks of the metals that were distinctly separated by 200 mV or more, allowing their determination over a wide range of concentrations. These metals can be quantified at concentrations above 1.33x10(-8) mol dm(-3) Cd(II), 8.51x10(-9) mol dm(-3) Ni(II) and 3.39x10(-10) mol dm(-3) Co(II). The influence of pH, ligand concentration, scan rate, accumulations time and applied potential was investigated. The R.S.D. at a concentration level of 1.78x10(-7) mol dm(-3) of Cd(II), 3.40x10(-7) mol dm(-3) and Ni(II) and 1.7x10(-9) mol dm(-3) of Co(II) was 2.5% for Cd(II), 2.7% for Ni(II) and 3.3% for Co(II). The method was applied to various water samples.     

Photophysics and Photocatalytic Properties of Cd(OH)(2)-Coated Q-CdS Clusters in the Presence of Guanine and Related Compounds

The photophysics of Cd(OH)(2)-coated Q-CdS in the presence of guanine and related compounds has been examined. Guanine and adenine quench the bandgap emission and reduce the emission lifetime of these particles. Approximately 50% of the bandgap fluorescence is quenched by a low [guanine] (2x10(-5) mol dm(-3)). Quenching takes place with a bimolecular rate constant of 2x10(12) dm(3) mol(-1) s(-1). The presence of these additives did not affect the red emission appreciably. The nature of the interaction between Cd(OH)(2) layer of Q-CdS and the additive has been analyzed by fluorescence and absorption spectroscopy. Interception of the hole by guanine and adenine occurs through their adsorption and hydrogen-bonding interaction between the -OH of Cd(OH)(2) and certain functional groups of the additive. Cd(OH)(2)-coated Q-CdS sensitizes the photodecomposition of guanine efficiently in the presence of oxygen under visible light irradiation. Shallowly trapped and direct holes are suggested to participate in the oxidation. The reactivity of the hole is governed by the redox potential of the solute. Copyright 2001 Academic Press.     

Hydroxypropyl-beta-cyclodextrin enhanced fluorimetric method for the determination of melatonin and 5-methoxytryptamine

The effects of native cyclodextrins (alpha, beta or gamma), hydroxypropyl-beta-cyclodextrin, beta-cyclodextrin solubilized in urea, soluble starch and glucose in water solution on the fluorescence behaviour of melatonin (N-acetyl-5-methoxytryptamine) (M) and 5-methoxytryptamine [5-methoxy-3-(2-aminoethyl)indole] (5M) were determined. In addition, the effect of methanol and propanol with and without beta-cyclodextrin or hydroxypropyl-beta-cyclodextrin was assessed. From the fluorescence changes with pH, the values of the pKa for the ground (9.9 +/- 0.2) and the excited state (7.7 +/- 0.2) for 5M were determined. From the fluorescence changes with beta-cyclodextrin or hydroxypropyl-beta-cyclodextrin, the association constants of M, 5MH [5-methoxy-3-(2-ammoniumethyl)indole] and 5M with the two hosts were determined. The values with beta-cyclodextrin were KAssoc5MH = (1.4 +/- 0.4) x 10(2) mol-1 dm3, KAssoc5M = (1.6 +/- 0.1) x 10(2) mol-1 dm3 and KAssocM = (1.1 +/- 0.2) x 10(2) mol-1 dm3, and with hydroxypropyl-beta-cyclodextrin KAssoc5MH = (1.1 +/- 0.3) x 10(2) mol-1 dm3, KAssoc5M = (2.5 +/- 0.1) x 10(2) mol-1 dm3 and KAssocM = (1.51 +/- 0.07) x 10(2) mol-1 dm3. The ratios of the fluorescence quantum yields for the bound and free substrate (phi b/phi f) were in the range 1.15-1.48. The detection limits under the optimum conditions were 0.381 +/- 0.001 ng cm-3 for the complex 5MH-hydroxypropyl-beta-cyclodextrin in water and 0.290 +/- 0.001 ng cm-3 for the complex M-hydroxypropyl-beta-cyclodextrin in water with 5% of methanol. The recovery of melatonin from pharmaceutical preparations was 98-103% with an RSD of 2%. The recovery from rat pineals was also good. The method is direct, simple and accurate.     

Spectrophotometric determination of sulfide in the presence of sulfite and thiosulfate via the precipitation of bismuth(III) sulfide.

A photometric method has been developed for the determination of sulfide at 10(-5) mol dm(-3) levels, which is based on the reaction of sulfide with a given excess amount of bismuth(III) to form a precipitate of bismuth(III) sulfide and on the spectrophotometric measurement of the residual bismuth(III) at 335 nm after extracting with bismuthiol II reagent from an aqueous solution containing acetate buffer into benzene. The presence of sulfite and thiosulfate up to 0.002 mol dm(-3) did not cause any interference in the determination of sulfide, because both sulfite and thiosulfate do not produce any precipitate with bismuth(III). A linear calibration plot with a negative slope was obtained for sulfide over the range of 5.00 x 10(-7) - 3.00 x 10(-5) mol dm(-3) (16.0 - 960 ppb). An experimental calibration plot was in accord with the theoretical plot, taking into account the known excess of bismuth(III), showing that the reaction of sulfide with bismuth(III) proceeded to completion. The relative standard deviation of results from 10 replicate determinations of standard sulfide (2.00 x 10(-5) mol dm(-3)) was 0.44%. The proposed method was successfully applied to the determination of sulfide in hotspring water samples without any pretreatment.     

Application of sequential injection analysis to the determination of cationic surfactants based on the sensitized molybdenum-bromopyrogallol red reaction.

The aim of this work was to develop a simple, automatic system for the evaluation of cationic surfactants by combining sequential injection analysis and the sensitized effect of cationic surfactants on the reaction between metal ions and chelating dyes. This reaction is based on the increase in absorbance of the complex formed among molybdenum, bromopyrogallol red and increasing concentrations of cationic surfactants. Under optimum conditions, two calibration plots were obtained for a concentration range between 2.50 x 10(-7) mol dm(-3) (detection limit) and 5.00 x 10(-4) mol dm(-3) of cetylpyridinium chloride, used as standard. Solubilization of water insoluble complexes formed for concentrations of cationic surfactants greater than 1.00 x 10(-4) mol dm(-3) were successfully achieved with Triton X-405. RSD values lower than 5.0% were obtained in all cases. The quality of the results obtained for 18 water samples were evaluated by comparison with conventional methods, with no statistically significant differences for a 95% confidence level.     

Polarographic study of acrolein and its determination by flow injection with amperometric detection at a mercury electrode

A study of the electrochemical behavior of acrolein at a dropping mercury electrode using different polarographic techniques is described. Theoretical studies of the reversibility of the wave of acrolein were carried out using two different polarographic techniques: direct current tast and differential pulse. Differential pulse polarography may be used to determine acrolein concentration in a Britton-Robinson buffer solution of pH 10 in the ranges 2 x 10(-7)10(-8) and 5 x 10(-8)-10(-4) mol dm(-3) and a coefficient of variation of 1.7% for a concentration of 10(-5)mol dm(-3). A flow injection method with amperometric detection at a potential of -1.4V using a mercury electrode is also described. Before each injection, any drop hanging from the tip of the capillary needs to be dislodged and a new electrode drop dispensed; three different drop sizes were tested. A linear relationship between peak intensity and acrolein concentration was obtained in the range 10(-5)-10(-7) mol dm(-3), with a detection limit of 9.8 x 10(-8) mol dm(-) 3 and a coefficient of variation of 2.9% for a 2 x 10(-7) mol dm(-3) concentration. Several organic and inorganic species were tested in order to ascertain whether they interfered with the signal for acrolein. The proposed methods were applied to the determination of acrolein in seawater samples.     

Homogeneous liquid-liquid extraction method for spectrofluorimetric determination of chlorophyll a

A new homogeneous liquid-liquid extraction using a fluorocarbon ionic surfactant, Zonyl FSA (FSA), having a diethylthioether group as a spacer between the perfluoroalkyl group and carboxyl group has been developed. In this FSA method, the phase separation phenomena were observed at mild pH (below pH 6). Moreover, by using this extraction method as a preconcentration, a highly sensitive spectrofluorometric determination of chlorophyll a was established. The results for the standard chlorophyll a were as follows. The concentration factor (V(w)/V(o)) was 200 (water phase, V(w), 20 cm(3), water-immiscible phase, V(o), 100 mul), the distribution ratio, log D, was 4.85, the extraction percentage, E, was 99.7%, and the procedure time was approximately 30 min. The calibration curve was linear in the concentration range 2 x 10(-11)-3 x 10(-7) mol dm(-3) and the detection limit (S/N=3) was 1 x 10(-11) mol dm(-3). The relative standard deviation was 0.72% for 10(-8) mol dm(-3) (five determinations).     

Simple method of paroxetine determination using a single channel FIA with no in-line reaction process.

A flow-injection analysis (FIA) of paroxetine hydrochloride (PRX), a selective serotonin reuptake inhibitor (SSRI) currently used as an antidepressant drug, is described. A 0.1 mol dm(-3) acetate buffer at pH 3.07 was found to be thebest solvent. The analyte was detected at 293 nm. The calibration equation was linear over the range of 1.07 x 10(-6) to 5.35 x 10(-6) mol dm(-3). The limit of detection (LOD) and the limit of quantitation (LOQ) were 3.2 x 10(-7) and 9.5 x 10(-7) mol dm(-3), respectively. The proposed method was applied to the determination of PRX in pharmaceutical preparations. The results were compared with those obtained by a conventional batchwise UV-spectrophotometry.     

Dissolution of Nickel Ferrite in Aqueous Solutions Containing Oxalic Acid and Ferrous Salts

The dissolution of nickel ferrite in oxalic acid and in ferrous oxalate-oxalic acid aqueous solution was studied. Nickel ferrite was synthesized by thermal decomposition of a mixed tartrate; the particles were shown to be coated with a thin ferric oxide layer. Dissolution takes place in two stages, the first one corresponding to the dissolution of the ferric oxide outer layer and the second one being the dissolution of Ni(1.06)Fe(1.96)O(4). The kinetics of dissolution during this first stage is typical of ferric oxides: in oxalic acid, both a ligand-assisted and a redox mechanism operates, whereas in the presence of ferrous ions, redox catalysis leads to a faster dissolution. The rate dependence on both oxalic acid and on ferrous ion is described by the Langmuir-Hinshelwood equation; the best fitting corresponds to K(1)(ads)=25.6 mol(-1) dm(-3) and k(1)(max)=9.17x10(-7) mol m(-2) s(-1) and K(2)(ads)=37.1x10(3) mol(-1) dm(-3) and k(2)(max)=62.3x10(-7) mol m(-2) s(-1), respectively. In the second stage, Langmuir-Hinshelwood kinetics also describes the dissolution of iron and nickel from nickel ferrite, with K(1)(ads)=20.8 mol(-1) dm(3) and K(2)(ads)=1.16x10(5) mol(-1) dm(3). For iron, k(1)(max)=1.02x10(-7) mol of Fe m(-2) s(-1) and k(2)(max)=2.38x10(-7) mol of Fe m(-2) s(-1); for nickel, the rate constants k(1)(max) and k(2)(max) are 2.4 and 1.79 times smaller, respectively. The factor 1.79 agrees nicely with the stoichiometric ratio, whereas the factor 2.4 implies the accumulation of some nickel in the residual particles. The rate of nickel dissolution in oxalic acid is higher than that in bunsenite by a factor of 8, whereas hematite is more reactive by a factor of 9 (in the absence of Fe(II)) and 27 (in the presence of Fe (II)). It may be concluded that oxalic acid operates to dissolve iron, and the ensuing disruption of the solid framework accelerates the release of nickel. Copyright 2000 Academic Press.     

Malonic acid concentration as a control parameter in the kinetic analysis of the Belousov-Zhabotinsky reaction under batch conditions

The influence of the initial malonic acid concentration [MA]0 (8.00 x 10(-3) < or = [MA]0 < or = 4.30 x 10(-2) mol dm(-3)) in the presence of bromate (6.20 x 10(-2) mol dm(-3)), bromide (1.50 x 10(-5) mol dm(-3)), sulfuric acid (1.00 mol dm(-3)) and cerium sulfate (2.50 x 10(-3) mol dm(-3)) on the dynamics and the kinetics of the Belousov-Zhabotinsky (BZ) reactions was examined under batch conditions at 30.0 degrees C. The kinetics of the BZ reaction was analyzed by the earlier proposed method convenient for the examinations of the oscillatory reactions. In the defined region of parameters where oscillograms with only large-amplitude relaxation oscillations appeared, the pseudo-first order of the overall malonic acid decomposition with a corresponding rate constant of 2.14 x 10(-2) min(-1) was established. The numerical results on the dynamics and kinetics of the BZ reaction, carried out by the known skeleton model including the Br2O species, were in good agreement with the experimental ones. The already found saddle node infinite period (SNIPER) bifurcation point in transition from a stable quasi-steady state to periodic orbits and vice versa is confirmed by both experimental and numerical investigations of the system under consideration. Namely, the large-amplitude relaxation oscillations with increasing periods between oscillations in approaching the bifurcation points at the beginning and the end of the oscillatory domain, together with excitability of the stable quasi-steady states in their vicinity are obtained.     

Interaction of 2- and 4-mercaptopyridine with pentacyanoferrates and gold nanoparticles

2-Mercapto- and 4-mercaptopyridine (2- and 4MPy) react with the [Fe(CN)(5)(H(2)O)](3-) complex, forming the S-coordinated [Fe(CN)(5)(2MPy)](3-) and the N-coordinated [Fe(CN)(5)(4MPy)](3-) complexes. The rates of formation and dissociation of the [Fe(II)(CN)(5)(2MPy)](3-) complex were determined as k(f) = 294 dm(3) mol(-1) s(-1) and k(d) = 0.019 s(-1) by means of stopped-flow technique. The equilibrium constants for the iron(II) and -(III) species were calculated as K(f)(II) = 1.5 x 10(4) mol(-1) dm(3) and K(f)(III) = 1.3 x 10(6) mol(-1) dm(3), in comparison with 2.6 x 10(5) and 3.4 x 10(4) mol(-1) dm(3), respectively, for the 4MPy isomer. In the presence of gold nanoparticles, both 2- and 4MPy can displace the stabilizing citrate species, leading to substantial aggregation in aqueous solution, as deduced from the surface-enhanced Raman spectroscopy effect and from the decay of the 520-nm plasmon band accompanied by the rise of the characteristic exciton band at 650 nm. The [Fe(CN)(5)(4MPy)](3-) complex promotes strong stabilization of the gold nanoparticles by interacting through the S atom. On the other hand, the labile [Fe(CN)(5)(2MPy)](3-) complex induces aggregation, delivering the 2MPy ligand to the gold nanoparticles.     

Synergistic effect of Ni(II) and Co(II) ions on the sulfite induced autoxidation of Cu(II)/tetraglycine complex

The synergistic effect of Ni(II) and Co(II) on the sulfite induced autoxidation of Cu(II)/tetraglycine was investigated spectrophotometrically at 25.0 degrees C, pH = 9.0, 1 x 10(-5) mol dm(-3) < or = [S(IV)] < or = 8 x 10(-5) mol dm(-3), [Cu(II)]= 1 x 10(-3) mol dm(-3), 1 x 10(-6) mol dm(-3) < or = [Ni(II)] or [Co(II)] < or = 1 x 10(-4) mol dm(-3), [O2] approximately 2.5 x 10(-4) mol dm(-3), and 0.1 mol dm(-3) ionic strength. In the absence of added nickel(II) or cobalt(II), the kinetic traces of Cu(III)G4 formation show a large induction period (about 3 h). The addition of trace amounts of Ni(II) or Co(II) increases the reaction rate significantly and the induction period drastically decreases (less than 0.5 s). The effectiveness of Cu(III)G4 formation becomes much higher. The metal ion in the trivalent oxidation state rapidly oxidizes SO3(2-) to SO3*-, which reacts with oxygen to produce SO5*-. The strongly generated oxidants oxidize Cu(II)G4 to Cu(III).     

Experimental and theoretical study of anion-exchange preparative chromatography for neptunium: the first application to thorium(IV) and its equilibrium and kinetics

In order to study equilibrium and kinetic parameters in anion-exchange chromatography for preparatory purpose, a quantitative model for nonlinear anion-exchange chromatography in porous media was constructed, by paying special attention to interstitial length along void structure (cm) distinguished from apparent length (cm*). Langmuir-type adsorption isotherm for thorium(IV), as a natural substitution for neptunium(IV), in 6 mol dm(-3) nitric acid to anion-exchanger MSA-1 (200-400 mesh) was investigated in batch-wise and chromatographic experiments. The equilibrium parameters determined by batch-wise experiments determined as k=2.4x10(2) mol(-1) dm3 s(-1) and s0=0.5 mol dm(-3) agrees very well with the values of k=222 mol(-1) dm3 s(-1) and s0=0.5 mol dm(-3) derived from fitting by the numerical calculation. Kinetic parameters of ks and D affect band profile similarly, thereby maximum value of each parameter was evaluated as ks=1.3 mol(-1) dm3 s(-1) and D=9x10(-4) cm2 s(-1) by the numerical calculations.     

Primary photophysical properties of moxifloxacin--a fluoroquinolone antibiotic

Abstract The photophysical properties of the fluoroquinolone antibiotic moxifloxacin (MOX) were investigated in aqueous media. MOX in water, at pH 7.4, shows two intense absorption bands at 287 and 338 nm (epsilon = 44 000 and 17 000 dm(3) mol(-1) cm(-1), respectively). The absorption and emission properties of MOX are pH-dependent, pK(a) values for the protonation equilibria of both the ground (6.1 and 9.6) and excited singlet states (6.8 and 9.1) of MOX were determined spectroscopically. MOX fluoresces weakly, the quantum yield for fluorescence emission being maximum (0.07) at pH 8. Phosphorescence from the excited triplet state in frozen ethanol solution has a quantum yield of 0.046. Laser flash photolysis and pulse radiolysis studies have been carried out to characterize the transient species of MOX in aqueous solution. On laser excitation, MOX undergoes monophotonic photoionization with a quantum yield of 0.14. This leads to the formation of a long-lived cation radical whose absorption is maximum at 470 nm (epsilon(470) = 3400 dm(3) mol(-1) cm(-1)). The photoionization process releases hydrated electron which rapidly reacts (k = 2.8 x 10(10) dm(3) mol(-1) s(-1)) with ground state MOX, yielding a long-lived anion radical with maximum absorption at 390 nm (epsilon(390) = 2400 dm(3) mol(-1) cm(-1)). The cation radical of MOX is able to oxidize protein components tryptophan and tyrosine. The bimolecular rate constants for these reactions are 2.3 x 10(8) dm(3) mol(-1) s(-1) and 1.3 x 10(8) dm(3) mol(-1) s(-1), respectively. Singlet oxygen sensitized by the MOX triplet state was also detected only in oxygen-saturated D(2)O solutions, with a quantum yield of 0.075.     

Cathodic stripping voltammetry of the anticancer agent 5-fluorouracil and determination in urine

Cathodic stripping voltammetry was used to determine 5-fluorouracil (5-FU) in the presence of traces of Cu(II). It was found that the addition of 5 x 10(-9) mol dm(-3) Cu(II) to the measurement cell greatly enhanced the peak current of the adsorbed molecule. Different parameters were tested to optimize the conditions for the determination of 5-FU. The adsorbed form is reduced irreversibly. It was observed that by controlling the deposition potential, the technique could be directed to the determination of Cu(II) or the drug. The linear range was from 5 x 10(-9) to 6 x 10(-8) mol dm(-3) for 5-FU and from 6 x 10(-9) to 5 x 10(-8) mol dm(-3) for Cu(II). Detection limits of 4.6 x 10(-10) and 5 x 10(-10) mol dm(-3) were obtained for 5-FU and Cu(II), respectively. The method was applied to urine and molecules or ions which may interfere were studied.     

Equilibrium constant of the gamma-sultone and extraction constant of sodium and potassium ions from water into benzene in presence of 18-crown-6 and bromocresol green

An extraction procedure for the spectrophotometric determination of sodium or potassium involving a 1:1:1 metal ion: crown ether: sulfonephthalein dye monoanion ion associate has been described in the literature. In a recent paper from this laboratory the total dye content of the organic phase resulting from partitioning bromocresol green (HBCG) alone between water and benzene was determined from back extraction into an aqueous phosphate buffer. In benzene, bromocresol green is present to a large extent as a colorless lactone form, or gamma-sultone. The sultone equilibrium constant, K(dist) (sultone)=[sultone](o)/[BCG(-)](w)gamma(BCG(-))(w)a(H(+)) was found to be 373+/-42 mol(-1) dm(3). In the present study, sodium was extracted from water into benzene with 18-crown-6 and BCG(-), yielding K(dist) (sultone)=232 mol(-1) dm(3) and the conventional extraction constant, K(ex), of (5.49+/-0.49)x10(3) mol(-2) dm(6). Corresponding values from potassium extraction data are 256 mol(-1) dm(3) and (4.80+/-0.51)x10(6) mol(-2) dm(6), respectively. In the absence of ethanol, the calibration plot of sodium closely followed Beer's law, but that of potassium curved downward, approaching linearity in 15% ethanol. High 18-crown-6, low bromocresol green concentrations are analytically favorable for the extraction of potassium from the 15% aqueous ethanol mixture. All plots from the back-extractions (a measure of the total dye content in the benzene phase) were linear. Ethanol markedly reduced the reagent blank, when C(MCl)=0, as a result of the sultone being partitioned less favorably into benzene.     

Photophysics and charge dynamics of Q-PbS based mixed ZnS/PbS and PbS/ZnS semiconductor nanoparticles

The surface of ZnS and PbS has been modified by interfacing PbS on ZnS and ZnS on PbS nanoparticles. This produced core-shell nanocomposites ZnS/PbS and PbS/ZnS with tunable electronic properties. In both structures PbS particles are present in cubic form with an average diameter of about 6 nm. The addition of Pb2+ (3 x 10(-4) mol dm(-3)) to Q-ZnS (1.5 x 10(-4) mol dm(-3)) in the basic pH range produces size-quantized fluorescent PbS particles coated by metal hydroxides. In these particles the relaxation kinetics of charge carriers has been followed using a picosecond single-photon counting technique. At 1.5 x 10(-4) mol dm(-3) Pb2+ an interfacial relaxation of charge from ZnS to PbS phase could be observed in subnanosecond time domain. An increase in [Pb2+] from 2 x 10(-4) to 1 x 10(-3) mol dm(-3) enhanced the average emission lifetime from 9.4 to 19.4 ns. Composite PbS/ZnS particles are produced at high [ZnS] only. These particles had emission lifetime in mus time range. The extent of charge separation and the dynamics of charge carriers could be manipulated by the surface modification of these nanostructures.     

Cyclodextrin and modified cyclodextrin complexes of E-4-tert-butylphenyl-4'-oxyazobenzene: UV-visible, 1H NMR and ab initio studies

alpha-Cyclodextrin, beta-cyclodextrin, N-(6(A)-deoxy-alpha-cyclodextrin-6(A)-yl)-N'6(A)-deoxy-beta-cyclodextrin-6(A)-yl)urea and N,N-bis(6(A)-deoxy-beta-cyclodextrin-6(A)-yl)urea (alphaCD, betaCD, 1 and 2) form inclusion complexes with E-4-tert-butylphenyl-4'-oxyazobenzene, E-3(-). In aqueous solution at pH 10.0, 298.2 K and I = 0.10 mol dm(-3)(NaClO(4)) spectrophotometric UV-visible studies yield the sequential formation constants: K(11) = (2.83 +/- 0.28) x 10(5) dm(3) mol(-1) for alphaCD.E-(-), K(21) = (6.93 +/- 0.06) x 10(3) dm(3) mol(-1) for (alphaCD)(2).E-3(-), K(11) = (1.24 +/- 0.12) x 10(5) dm(3) mol(-1) for betaCD.E-(-), K(21) = (1.22 +/- 0.06) x 10(4) dm(3) mol(-1) for (betaCD)(2).E-(-), K(11) = (3.08 +/- 0.03) x 10(5) dm(3) mol(-1) for .E-3(-), K(11) = (8.05 +/- 0.63) x 10(4) dm(3) mol(-1) for .E-3(-) and K(12) = (2.42 +/- 0.53) x 10(4) dm(3) mol(-1) for .(E-3(-))(2). (1)H ROESY NMR studies show that complexation of E-3(-) in the annuli of alphaCD, betaCD, 1 and 2 occurs. A variable-temperature (1)H NMR study yields k(298 K)= 6.7 +/- 0.5 and 5.7 +/- 0.5 s(-1), DeltaH = 61.7 +/- 2.7 and 88.1 +/- 4.2 kJ mol(-1) and DeltaS = -22.2 +/- 8.7 and 65 +/- 13 J K(-1) mol(-1) for the interconversion of the dominant includomers (complexes with different orientations of alphaCD) of alphaCD.E-3(-) and (alphaCD)(2).E-3(-), respectively. The existence of E-3(-) as the sole isomer was investigated through an ab initio study.     

Ozonolysis of vinyl compounds,CH2=CH-X,in aqueous solution--the chemistries of the ensuing formyl compounds and hydroperoxides

Reactions of ozone with some vinyl compounds of the general structure CH2=CH-X were studied in aqueous solution. Rate constants (in brackets, unit: dm3 mol-1 s-1) were determined: acrylonitrile (670), vinyl acetate (1.6 x 10(5)), vinylsulfonic acid (anion, 8.3 x 10(3)), vinyl phenylsulfonate (ca. 200), vinyl diethylphosphonate (3.3 x 10(3)), vinylphosphonic acid (acid, 1 x 10(4); mono-anion, 2.7 x 10(4); di-anion, 1 x 10(5)), vinyl bromide (1 x 10(4)). The main pathway leads to the formation of HOOCH2OH and HC(O)X. As measured by stopped flow with conductometric detection, the latter one may undergo rapid hydrolysis by water, e.g. HC(O)CN (3 s-1). Other HC(O)X hydrolyse much slower, e.g. HC(O)PO3(Et)2 (7 x 10(-3) s-1) and HC(O)P(OH)O2- (too slow to be measured). The OH(-)-induced hydrolyses range from ca. 5 dm3 mol-1 s-1 [HC(O)PO(3)2-] to 3.8 x 10(5) dm3 mol-1 s-1 [HC(O)CN]. HC(O)Br mainly decomposes rapidly (too fast for the determination of the rate) into CO and Br- plus H+, and the competing hydrolysis is of minor importance (3.7%). The slow hydrolysis of HC(O)PO(3)2- at pH 10.2, where HOOCH2OH is rapidly decomposed into CH2O plus H2O2, allows an H2O2-induced decomposition (k = 260 dm3 mol-1 s-1) to take place. Formate and phosphate are the final products.     

A DANREF certified reference plastic for measurement of overall migration into the food simulant olive oil by single sided testing

A reference material for the determination of overall migration from a plastic coextrudate into the fatty food simulant olive oil was produced and certified in an interlaboratory study. The analyses were carried out according to the ENV 1186 standard from the European Committee for Standardization (CEN) [ 1, 2, 3] with exposure of the coextrudate to olive oil for 10 days at 40 degrees C. After an initial preliminary interlaboratory study eight laboratories participated in the certification round, and two different methods were used to obtain single sided exposure of the plastic to the oil. The certified value was determined as the mean of laboratory mean values. No outliers were found. A reference value of 8.6 mg/dm2 +/- 1.4 mg/dm2 (+/- half width of the 95% confidence interval) was obtained which is within the range relevant for the regulatory limit (10 mg/ dm2), making this reference material suitable for laboratories measuring according to the EU overall migration limit [4]. The material has been found stable over 45 months.