Metallo‐supramolecular block copolymer micelles: Improved preparation and characterization

Micelles prepared from amphiphilic block copolymers in which a poly(styrene) segment is connected to a poly(ethylene oxide) block via a bis‐(2,2′:6′,2″‐terpyridine‐ruthenium) complex have been intensely studied. In most cases, the micelle populations were found to be strongly heterogeneous in size because of massive micelle/micelle aggregation. In the study reported in this article we tried to improve the homogeneity of the micelle population. The variant preparation procedure developed, which is described here, was used to prepare two “protomer”‐type micelles: PS₂₀‐[Ru]‐PEO₇₀ and PS₂₀‐[Ru]‐PEO₃₇₅. The dropwise addition of water to a solution of the compounds in dimethylformamide was replaced by the controlled addition of water by a syringe pump. The resulting micelles were characterized by sedimentation velocity and sedimentation equilibrium analyses in an analytical ultracentrifuge and by transmission electron microscopy of negatively stained samples. Sedimentation analysis showed virtually unimodal size distributions, in contrast to the findings on micelles prepared previously. PS₂₀‐[Ru]‐PEO₇₀ micelles were found to have an average molar mass of 318,000 g/mol (corresponding to 53 protomers per micelle, which is distinctly less than after micelle preparation by the standard method) and an average hydrodynamic diameter (d_h) of 18 nm. For PS₂₀‐[Ru]‐PEO₃₇₅ micelles, the corresponding values were M = 603,000 g/mol (31 protomers per micelle) and d_h = 34 nm. The latter particles were found to be identical to the “equilibrium” micelles prepared in pure water. Both micelle types had a very narrow molar mass distribution but a much broader distribution of s values and thus of hydrodynamic diameters. This indicates a conformational heterogeneity that is stable on the time scale of sedimentation velocity analysis. The findings from electron microscopy were in disagreement with those from the sedimentation analysis both in average micelle diameter and in the width of the distributions, apparently because of imperfections in the staining procedure. The preparation procedure described also may be useful in micelle formation from other types of protomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4458–4465, 2004     

Managing polymer surface structure using surface active block copolymers in block copolymer mixtures

Surface coatings were prepared from semifluorinated monodendron surface‐active block copolymers (SABC) and a thermoplastic elastomer (TPE) [poly(styrene‐b‐ethylene butylene‐b‐styrene)] by either spin‐casting a bilayer structure or by blending. The surface of these coatings was characterized by contact angle measurements, scanning force microscopy (SFM) and near‐edge X‐ray absorption fine structure (NEXAFS) methods. Both bilayers and blends resulted in very low energy surfaces under the right processing conditions and the liquid crystallinity of the semifluorinated monodendrons gave rise to temporally stable, non‐reconstructing surfaces in water. However for small thicknesses of the SABC top layer or for low SABC content blends, SFM shows islands of the fluorinated block of the SABC and incomplete surface coverage of the TPE, an observation confirmed by NEXAFS analysis. Very high water contact angles were produced by even modest amounts of SABC in either case but to achieve low contact angle hysteresis, it was necessary to produce uniform surface coverage by the SABC. Such uniform coverage can be accomplished by spin casting a top layer of SABC as thin as 60 nm in the bilayer case but at least 10 wt% SABC in TPE combined with drop casting of a hot solutions is needed for the blends to achieve equivalent surface structure and properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 411–420, 2004     

Novel poly(l‐lactide)/poly(d‐lactide)/poly(tetrahydrofuran) multiblock copolymers with a controlled architecture: Synthesis and characterization

Novel poly(l ‐lactide) (PLLA)/poly(d ‐lactide) (PDLA)/poly(tetrahydrofuran) (PTHF) multiblock copolymers with designed molecular structure were synthesized by a two‐stage procedure. Well‐defined PDLA‐PLLA‐PTHF‐PLLA‐PDLA pentablock copolymers were prepared by sequential ring opening polymerization of l ‐ and d ‐lactides starting from PTHF glycol, with the length of the (equimolar) PLLA and PDLA blocks being varied. Then, these dihydroxyl‐terminated pentamers were transformed into multiblock copolymers by melt chain‐extension with hexamethylene diisocyanate–being the first time that the coupling of pentablock units is reported. The successful formation of macromolecular chains with a multiblock and well‐defined architecture was demonstrated by ¹H NMR spectroscopy. The thermal properties and structuring of the resulting materials were investigated by means of DSC and WAXD measurements and DMA analysis. Stereocomplexation was found to be promoted during solution and melt crystallization. This approach affords materials combining the high rigidity and strength (other than improved thermal resistance) of the hard stereocomplex crystallites with the flexibility imparted by the soft block, whereby their properties can be finely tailored through the composition of the basic pentablock units without limitations on the final molecular weight. The adopted reaction conditions make this process highly appealing in view of the possibility to perform it in extruder. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3269–3282     

Multiblock poly(4‐vinylpyridine) and its copolymer prepared with cyclic trithiocarbonate as a reversible addition–fragmentation transfer agent

The polymerization of 4‐vinylpyridine was conducted in the presence of a cyclic trithiocarbonate (4,7‐diphenyl‐[1,3]dithiepane‐2‐thione) as a reversible addition–fragmentation transfer (RAFT) polymerization agent, and a multiblock polymer with narrow‐polydispersity blocks was prepared. Two kinds of multiblock copolymers of styrene and 4‐vinylpyridine, that is, (ABA)_n multi‐triblock copolymers with polystyrene or poly(4‐vinylpyridine) as the outer blocks, were prepared with multiblock polystyrene or poly(4‐vinylpyridine) as a macro‐RAFT agent, respectively. GPC data for the original polymers and polymers cleaved by amine demonstrated the successful synthesis of amphiphilic multiblock copolymers of styrene and 4‐vinylpyridine via two‐step polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2617–2623, 2007     

Effects of an avidin-biotin binding system on chondrocyte adhesion and growth on biodegradable polymers

Cell adhesion to a scaffold is a prerequisite for tissue engineering. Many studies have been focused on enhancing cell adhesion to synthetic materials that are used for scaffold fabrication. In this study, we applied an avidin-biotin binding system to enhance chondrocyte adhesion to biodegradable polymers. Biotin molecules were conjugated to the cell membrane of chondrocytes, and mediated cell adhesion to avidin-coated surfaces. We demonstrated that immobilization of biotin molecules to chondrocyte surfaces enhanced cell adhesion to avidin-coated biodegradable polymers such as poly(L-lactic acid), poly(D,L-lactic acid), and polycaprolactone, compared to the adhesion of normal chondrocytes to the same type of biodegradable polymer. The biotinylated chondrocytes still maintained their proliferation ability. This study showed the promise of applying the avidin-biotin system in cartilage tissue engineering. [diagram in text].     

pH-Sensitive pentablock copolymer nanocapsules as nontoxic and efficient gene carriers

A biodegradable amphiphilic pentablock copolymer PAE‐PCL‐PEG‐PCL‐PAE with a pH‐sensitive unit was synthesized for use as a nontoxic, biodegradable carrier for gene delivery by forming nanocapsules entrapping nucleic acid drugs. The PAE block can interact with plasmid DNA to form polyelectrolyte complexes in an acidic environment. At physiological pH, the PAE blocks are deprotonated and form an insoluble skin, resulting in the formation of nanocapsules that encapsulate plasmid DNA. The surface charges of the nanocapsules became almost neutral at pH = 7.4, and their size ranged from 210 to 280 nm. The nanocapsule maintained most of its transfection efficiency even in the presence of serum. These nanocapsules are therefore potential carriers for systemic gene therapy.

     

Novel pH sensitive block copolymer micelles for solvent free drug loading

Novel pH sensitive biodegradable block copolymers (MPEG-PDLLA-OSM) composed of mono-methoxy poly(ethylene glycol) (MPEG), poly (D,L-lactide) (PDLLA) and sulfamethazine oligomer (OSM) were synthesized via ring-opening polymerization and a dicyclohexyl carboimide (DCC) coupling reaction. These copolymers had a relatively low critical micelle concentration (CMC) due to the strong hydrophobic properties of non-ionized OSM at pH 7.0. Also, the pH sensitive block copolymers showed the micelle-unimer transition due to the ionization-non-ionization of OSM in the pH range (pH 7.2-8.4) above the CMC. Due to the pH sensitive properties of the block copolymer, the hydrophobic drug paclitaxel (PTX) was incorporated into a pH sensitive block copolymer micelle by the pH induced micellization method, without using an organic solvent. The block copolymer micelle prepared by pH induced micellization showed a relatively high PTX loading efficiency, and good stability for 2 d at 37 degrees C. Furthermore, the PTX loaded micelle showed a sustained release of PTX with a small burst in vitro over 2 d. The present results suggest that the pH induced micellization method due to the micelle-unimer transition of the pH sensitive block copolymer would be a novel and valuable drug incorporation tool for hydrophobic and protein drugs, since no organic solvent is involved in the formulation.     

in vitro biological evaluation of folate-functionalized block copolymer micelles for selective anti-cancer drug delivery

The main objective of this study was to evaluate the ability of folic acid-functionalized diblock copolymer micelles to improve the delivery and uptake of two poorly water-soluble anti-tumor drugs, tamoxifen and paclitaxel, to cancer cells through folate receptor targeting. The diblock copolymer used in this study comprised a hydrophilic poly[2-(methacryloyloxy)ethyl phosphorylcholine] (MPC) block, carrying at the chain end the folate targeting moiety, and a pH-sensitive hydrophobic poly[2-(diisopropylamino)ethyl methacrylate] (DPA) block (FA-MPC-DPA). The drug-loading capacities of tamoxifen- and paclitaxel-loaded micelles were determined by high performance liquid chromatography and the micelle dimensions were determined by dynamic light scattering and transmission electron microscopy. Cell viability studies were carried out on human chronic myelogenous leukaemia (K-562) and colon carcinoma cell lines (Caco-2) in order to demonstrate that drug-loaded FA-MPC-DPA micelles exhibited higher cytotoxicities toward cancer cells than unfunctionalized MPC-DPA micelles. Uptake studies confirmed that folate-conjugated micelles led to increased drug uptake within cancer cells, demonstrating the expected selectivity toward these tumor cells.     

Synthesis and characterization of a starch‐modified hydrogel as potential carrier for drug delivery system

Synthesis and characterization of a new hydrogel were carried out using a chemically modified starch (starch‐M) consisting of coupling C?C bounds coming from glycidil methacrylate (GMA) onto the polysaccharide structure. ¹³C NMR, ¹H NMR, and FT‐IR spectroscopies were used to confirm the incorporation of such groups onto the starch‐M. The hydrogel was prepared by a crosslinking polymerization of starch‐M using sodium persulfate as an initiating agent. The starch‐M hydrogel shows morphology clearly different from that of the raw starch film due to the presence of voids on its surface. The swelling process of the starch‐M hydrogel was not significantly affected by changes on the temperature or on pH of the surrounding liquid, indicating the such behavior can be then understood by a diffusional process, resulting from its physical–chemical interactions with the solvent. The values of the diffusional exponent n were on the order of 0.45–0.49 for the range of pHs investigated, demonstrating that the water transport mechanism of starch‐M hydrogel is more dependent on Fickian diffusion, that is, controlled by water diffusion. Such starch‐M hydrogel is a promising candidate to be used in transporting and in preserving acid‐responsive drugs, such as corticoids, for the treatment of colon‐specific diseases, for example, Crohn's disease. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2567–2574, 2008     

Revisiting thiol-yne chemistry: Selective and efficient monoaddition for block and graft copolymer formation

The untapped potential of radical thiol-yne mono-addition chemistry is exploited to overcome the known limitations of thiol-ene chemistry in polymer coupling and block copolymer formation. By careful choice of alkyne, the reaction can selectively lead to the mono-addition product with efficiencies surpassing those achieved by traditional thiol-ene chemistry. This improvement is illustrated by the nearly quantitative synthesis of a variety of diblock and graft copolymers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 319–326     

Chromatographic characterization of amphiphilic di‐ and tri‐block copolymers of poly(ethylene oxide) and poly(ε‐caprolactone)

Amphiphilic di‐ and tri‐block copolymers based on poly(ethylene oxide) as a hydrophilic segment and poly(ε‐caprolactone) as a hydrophobic part are synthesized by the ring‐opening polymerization of ε‐caprolactone while using poly(ethylene glycol)s and methoxy poly(ethylene glycol)s of varying molar masses as macro‐initiators. The synthesized block copolymers are characterized with respect to their total relative molar mass and its distribution by size exclusion chromatography. Liquid chromatography at critical conditions of both blocks is established for the analysis of individual block lengths and tracking presence of unwanted homopolymers of both types in the block copolymer samples. New critical conditions of polycaprolactone on reversed phase column are reported using organic mobile phase. The established critical conditions of polycaprolactone extended the applicable molar mass range significantly compared to already reported critical conditions of polycaprolactone in aqueous mobile phase. Block copolymers are also analyzed at critical conditions of poly(ethylene glycol). Complete analysis of the di‐ and tri‐block copolymers at corresponding critical conditions provided a fair estimate of molar mass of non‐critical block besides information regarding presence of homopolymers of both types in the samples.     

Synthesis and self‐assembly of amphiphilic macrocyclic block copolymer topologies

We demonstrated the synthesis of miktoarm star block copolymers of AB, AB₂, and A₂B, in which block A consisted of linear poly(tert‐butyl acrylate) (P^tBA) and block B consisted of cyclic polystyrene. These structures were produced using the atom transfer radical polymerization to make telechelic polymers that, after modification, were further coupled together by copper‐catalyzed “click” reactions with high coupling efficiency. Deprotection of P^tBA to poly(acrylic acid) (PAA) afforded amphiphilic miktoarm structures that when micellized in water gave vesicle morphologies when the block length of PAA was 21 units. Increasing the PAA block length to 46 units produced spherical core‐shell micelles. AB₂ miktoarm stars packed more densely into the core compared to its linear counterpart (i.e., a four times greater aggregation number with approximately the same hydrodynamic diameter), resulting in the PAA arms being more compressed in the corona and extending into the water phase beyond its normal Gaussian chain conformation. These results show that the cyclic structure attached to an amphiphilic block has a significant influence on increasing the aggregation number through a greater packing density. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Phase behavior and viscoelastic properties of entangled block copolymer gels

Triblock copolymers in midblock‐selective solvents can form physical gels. However, at low triblock contents (near the percolation threshold), the bridging of chains between micelles can lead to macrophase separation. Adding a styrene–isoprene diblock to a styrene–isoprene–styrene triblock copolymer in squalane can eliminate macrophase separation, yielding a wide range of stable, single‐phase gels with a disordered arrangement of micelles. The plateau modulus of these triblock gels scales with the 2.2 power of polymer content, indicating the importance of entanglements in dictating the modulus. Comparing gels made from the midblock‐saturated derivative of the same polymer [styrene‐(ethylene‐alt‐propylene)‐styrene] in squalane reveals that the modulus differences in the gels are a direct consequence of the difference in the entanglement molecular weight of the midblock homopolymer in bulk. Finally, the broad relaxation spectrum of these triblocks is well‐described by a recent theory for the dynamics of entangled star polymers, with the breadth of the relaxation spectrum dictated by the number of entanglements per midblock in the gel. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2183–2197, 2001     

Functionally integrated liquid crystalline photochromic triple block copolymer with locally light‐ and thermal‐controllable sub‐blocks

Photoorientation and reorientation processes induced by illumination of the samples with oppositely directed polarized light and by the thermal treatment were studied for the films of triblock copolymer pAzo₁₀‐b‐pPhM₈₀‐b‐pAzo₁₀ consisting of a nematic phenyl benzoate сentral sub‐block (PhM, DP = 80) with two terminal smectic azobenzene sub‐blocks (Azo, DP = 10). For amorphized films of triblock copolymer, illumination with polarized light (λ = 546 nm) is shown to be by orientation of only Azo‐containing groups, but upon following annealing of the film, PhM groups are adjusted to the orientation of Azo fragments. It was found, that the subsequent illumination of the block copolymer sample with oppositely directed polarized light changes the orientation of azobenzene groups, while the orientation of phenyl benzoate groups is remained unchanged. Thus, the cyclic illumination of the triblock copolymer samples by the linear polarized light and subsequent thermal treatment make it possible to control and fix orientation of azobenzene and phenyl benzoate groups located in different sub‐blocks in the desired and independent manner. The comparison of these results with the data on random p(Azo₇‐ran‐PhM₃₀) copolymer of the similar composition revealed, that in the random copolymer, both Azo and PhM mesogenic groups are involved in the orientational cooperative process regardless of films process treatment. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1602–1611     

Synthesis and self‐assembly of a chiral alternating sexithiophene–undeca(ethyleneoxy) block copolymer

An oligothiophene/chiral oligo(ethyleneoxy) block copolymer (PolyT6) has been synthesized in which a sexithiophene block alternates with a well‐defined chiral undeca(ethyleneoxy) block. The polymer shows good solubility in chloroform, and ultraviolet–visible studies in this solvent reveal a spectrum similar to that of the chirally substituted monomeric sexithiophene (T6) analogue. The aggregation of PolyT6 occurs in dioxane; however, no helicity is present in this aggregate, in contrast to aggregated T6. This behavior illustrates that although the processability and mechanical robustness of block copolymers may be superior to those of analogous oligomers, the degree of self‐assembled order found in oligomer‐based systems may be lost in the polymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1737–1743, 2003     

Synthesis and characterization of a film‐forming,crosslinked, amphiphilic block copolymer of butadiene and acrylamide

An amphiphilic block copolymer of acrylamide and butadiene was synthesized by the polymerization of acrylamide in the presence of the crosslinker N,N′‐methylene bisacrylamide initiated by a hydroxyl‐terminated polybutadiene/V(V) macroredox initiator. The product had good film‐forming ability. It was characterized by IR and NMR spectroscopy, viscosity, swelling, and microhardness measurements, scanning electron micrography, and differential scanning calorimetry. A good film was obtained from the block copolymer with a greater proportion of butadiene; it had greater permeability for nonpolar solvents, and it was poorly permeable to water and other polar solvents. The film swelled in polar and nonpolar solvents and had almost the same capacity for the loading and release of hydrophilic and hydrophobic dyes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3290–3303, 2006     

Control of all‐conjugated block copolymer crystallization via thermal and solvent annealing

Control of the crystallization of conjugated polymers is of critical importance to the performance of organic electronics, such as organic photovoltaic devices, due to the effect on charge separation and transport, particularly for all‐polymer devices. The block copolymer poly(3‐dodecylthiophene)‐block‐poly(9,9‐dioctylfluorene) (P3DDT‐b‐PF), which has matched crystallization temperatures for each block, is used to study the effects of processing history on resulting crystallization. For longer annealing times and rapid quenching to room temperature, P3DDT crystals are preferred whereas for shorter annealing times and slower quenching, PF crystals are preferred. Both crystal forms are evidenced for long annealing time and slow quenching. Additionally, for room temperature annealing in the presence of a chloroform vapor, PF crystals are found in the PF β phase with the predominant crystal peak oriented perpendicular to the thermally annealed case. These results will provide guidance for optimizing annealing strategies for future donor/acceptor block copolymer photovoltaic devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 900–906     

Simultaneous morphological stability and high charge carrier mobilities in donor–acceptor block copolymer/PCBM blends

Donor–acceptor block copolymers (BCP), incorporating poly(3‐hexylthiophene) (P3HT), and a polystyrene copolymer with pendant fullerenes (PPCBM) provide desired stable nanostructures, but mostly do not exhibit balanced charge carrier mobilities. This work presents an elegant approach to match hole and electron transport in BCP by blending with molecular PCBM without causing any macrophase separation. An insufficient electron mobility of PPCBM can be widely compensated by adding PCBM which is monitored by the space‐charge limited current method. Using X‐ray diffraction, atomic force microscopy, and differential scanning calorimetry, we verify the large miscibility of the PPCBM:PCBM blend up to 60 wt % PCBM load forming an amorphous, molecularly mixed fullerene phase without crystallization. Thus, blending BCP with PCBM substantially enhances charge transport achieving an electron mobility of μ_e=(3.2 ± 1.7) × 10^?4 cm²V^?1s^?1 and hole mobility of μ_h=(1.8 ± 0.6) × 10^?3 cm²V^?1s^?1 in organic field‐effect transistors (OFET). The BCP:PCBM blend provides a similarly high ambipolar charge transport compared to the established P3HT:PCBM system, but with the advantage of an exceptionally stable morphology even for prolonged thermal annealing. This work demonstrates the feasibility of high charge transport and stable morphology simultaneously in a donor–acceptor BCP by a blend approach. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1125–1136     

Synthesis and characterization of ABA-type block copolymer of poly(trimethylene carbonate) with poly(ethylene glycol): Bioerodible copolymer

ABA-type block copolymers of poly(trimethylene carbonate) with poly(ethylene glycol) (M_n 6820), PTMC-b-PEG-b-PTMC, were synthesized by the ring-opening polymerization of 1,3-dioxan-2-one (trimethylene carbonate) in the presence of poly-(ethylene glycol) with stannous octoate catalyst, and the copolymers with various compositions were obtained. The PTMC-b-PEG-b-PTMC copolymers were characterized with Fourier transform infrared and nuclear magnetic resonance spectroscopies. The intrinsic viscosities of resulting copolymers increased with the increase of 1,3-dioxan-2-one content in feed while the molar ratio of monomer over catalyst kept constant. It has been observed that the glass transition temperature (T_g) of the PTMC segments in copolymers, recorded from differential scanning calorimetry, was dependent on the composition of copolymers. The melting temperature (T_m) of PEG blocks in copolymer was lower than that of PEG polymer, and then disappeared as the length of PTMC blocks increased. The results of dynamic contact angle measurement clearly revealed that the hydrophilicity of resulting copolymers increased greatly with the increase of PEG content in copolymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 695–702, 1998     

Fusiform micelles from nonlinear poly(ethylene glycol)/polylactide copolymers as biodegradable drug carriers

PEG-PLA copolymers with dumbbell- and Y-shaped structures are prepared. They can self-assemble from nanoparticles to micro-sized fusiform micellar particles in aqueous solution. In particular the micelles formed by the (PLA)2-PEG-(PLA)2 particles show a better drug loading capacity and encapsulation efficiency than those formed by linear MPEG-PLA. In vitro studies show that the particles formed by Y-shaped copolymers show a particularly quick drug release. The copolymers have good biocompatibility with low cytotoxicity. These unique self-assembled systems thus have many possible biomedical applications, such as a sustained delivery of high-dosed water insoluble drugs, quick effective drugs for trauma, controlled delivery of the oral-administration drugs, and so forth.