Sol–gel synthesis of macroporous TiO2 from ionic precursors via phase separation route

Monolithic macroporous titanium dioxide (TiO₂) derived from ionic precursors has been successfully prepared via the sol–gel route accompanied by phase separation in the presence of formamide (FA) and poly(vinylpyrrolidone) (PVP). The addition of FA promotes the gelation, whereas PVP enhances the polymerization-induced phase separation. Appropriate choice of the starting compositions allows the production of cocontinuous macroporous TiO₂ monoliths in large dimensions, and controls the size of macropores. The resultant dried gel is amorphous, whereas anatase and rutile phases are precipitated at 500 and 900 °C respectively, without spoiling the macroporous morphology. Nitrogen adsorption–desorption measurements revealed that the dried gels exhibits mesostructure with a median pore size of about 3 nm and BET surface area of 228 m²/g, whereas 15 nm and 73 m²/g for the gels calcined at 600 °C.     

Synthesis of high surface area nanocrystalline anatase-TiO2 powders derived from particulate sol-gel route by tailoring processing parameters

Stabilised titania sols were prepared using an additive free particulate sol-gel route, via electrostatic stabilisation mechanism, with various processing parameters. Peptisation temperature, 50°C and 70°C, and TiO₂ concentration, 0.1, 0.2 and 0.4 molar, were chosen as processing parameters during sol preparation. Results from TiO₂ particle size and zeta potential of sols revealed that the smallest titania hydrodynamic diameter (13 nm) and the highest zeta potential (47.7 mV) were obtained for the sol produced at the lower peptisation temperature of 50°C and lower TiO₂ concentration of 0.1 M. On the other hand, between the sols prepared at 70°C, smaller titania particles (20 nm) and higher zeta potential (46.3 mV) were achieved with increasing TiO₂ concentration up to 0.4 M. X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) results of produced powders annealed at different temperatures showed that the 300°C annealed powder made from 0.1 M sol prepared at 50°C was a mixture of anatase and brookite, corresponding to a major phase of anatase (∼95% estimated), with the smallest average crystallite size of 1.3 nm and the highest specific surface area (SSA) of 193 m²/g. Furthermore, increasing TiO₂ concentration up to 0.4 molar for the sols prepared at 70°C resulted in decreasing the average crystallite size (1.9 nm at 300°C) and increasing SSA (116 m²/g at 300°C) of the powders annealed at different temperatures. Anatase-to-rutile phase transformation temperature was increased with decreasing peptisation temperature down to 50°C, whereas TiO₂ concentration had no effect on this transition. Anatase percentage increased with decreasing both peptisation temperature and TiO₂ concentration. Such prepared powders can be used in many applications in areas from photo catalysts to gas sensors.     

The effects of the nanostructure of mesoporous TiO<Subscript>2</Subscript> on optical band gap energy

Mesoporous TiO₂ is prepared by sol–gel process with a triblock copolymer as an organic template and aqueous TiOCl₂ solution as inorganic precursor. The XRD patterns reveal that only the anatase phase can be observed in mesoporous TiO₂, regardless of the different calcining temperatures, and with increasing calcining temperature the grain size gradually increases. The grain sizes of TiO₂ increased from 4.7 to 11.9 nm with calcining temperature increasing from 300 to 400 °C. The pore size and the surface area evaluated from the Barrett–Joyner–Halenda model and Brunauer–Emmett–Teller method indicated that the average pore sizes increased from 87 to 153 Å and specific surface areas decreased from 179.71 to 74.31 m²/g for 300–400 °C calcination. The relationship between the optical band gap (E _g) and microstructure of anatase has been determined and discussed. The quantum confinement effect is observed at grain sizes lower than 10 nm, and the estimated E _g shifts from 3.32 to 3.46 eV. These results suggest that there are potential applications of mesostructured TiO₂ with nanocrystals in the design of optical devices and photocatalysts.     

Boron-doped TiO2: Characteristics and photoactivity under visible light

Boron-doped TiO₂ was prepared by the sol-gel method and by grinding TiO₂ powder with a boron compounds (boric acid and boric acid triethyl ester followed by calcinations at temperature range 200 to 600°C. Three types of pristine TiO₂: ST-01 (Ishihara Sangyo Ltd., Japan; 300 m²/g), P25 (Degussa, Germany, 50 m²/g), A11 (Police S.A., Poland 12 m²/g) were used in grinding procedure. The photocatalytic activity of obtained powders in visible light was estimated by measuring the decomposition rate of phenol (0.21 mmol/dm³) in an aqueous solution. The photocatalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron emission spectroscopy (XPS), UV-VIS absorption and BET surface area measurements. The best photoactivity under visible light was observed for B-TiO₂ modified with 2 wt% of boron prepared by grinding ST-01 with dopant followed by calcinations at 400°C. This photocatalyst contains 16.9 at.% of carbon and 6.6 at.% of boron in surface layer and its surface area is 192 m²/g.     

Low-temperature versus oxygen plasma treatment of water-based TiO2 paste for dye-sensitized solar cells

High-temperature treatment steps in fabrication process of dye sensitized solar cell (DSSC) significantly contribute to the manufacturing costs and limit the use of temperature sensitive substrates. Therefore our aim was to develop a simple method for the preparation of water-based TiO₂ paste. The paste is based on peroxotitanic acid (PTA) sol–gel matrix and commercial TiO₂ nanoparticles (P25). Two fabrication processes to decompose/transform the PTA matrix in the printed TiO₂ layer are explored and combined: annealing at temperatures up to 250 °C and/or oxygen plasma treatment. The results show that the PTA matrix in the paste converts to anatase phase and to some extent also attaches to the TiO₂ nanoparticles P25 acting as an interconnecting network within TiO₂ layer. The transformation of the PTA matrix occurs around 250 °C, but in the presence of TiO₂ nanoparticles P25 it starts already at 120 °C. In addition the results reveal that the crystallization is achievable also solely with the oxygen plasma treatment. The efficiency of the TiO₂ layers, exposed to different post-deposition treatments, is evaluated in DSSCs. The results show that oxygen plasma treatment of the TiO₂ layers could efficiently replace temperature curing at 250 °C. Within this study the DSSCs with the efficiency up to 4.2 % measured under standard test conditions (1,000 W/m², AM1.5, 25 °C) were realized.     

Low-temperature sol–gel synthesis of anatase nanoparticles modified by Au, Pd and Pt and activity of TiO2/Au, Pd, Pt photocatalysts in water splitting

Base catalyzed hydrolysis and condensation of Ti isopropoxide with water at ambient temperature and molar ratio H₂O/Ti(i-PrOH)₄ varied from 1 to 100 was studied. It was found that molar ratio H₂O/Ti(i-PrOH)₄ = 100 originated amorphous TiO₂-precursor of summary composition TiO_1.9(OH)_0.2 with a specific surface area of 354 m²/g. Low-temperature crystallization of amorphous TiO₂-precursor to nanostructured anatase at 80 °C in a slightly reducing environment of d-glucose was studied. It was found that the low-temperature nucleation and crystallization of anatase was initiated (activated) by combined effects of d-glucose and Au⁰, Pd⁰ and Pt⁰ nanoparticles, generated in situ by slow reduction of Au³⁺, Pd²⁺ and Pt⁴⁺ ions using d-glucose. Considerable photocatalytic activity of Ti-hydroxide-oxide/Au, Pd, Pt catalysts prepared at low-temperature was associated with high content of nanostructured anatase and low content of Au, Pd and Pt nanoparticles (0.02 wt.%) effectively deposited on the surface of titania particles. The maximum hydrogen evolution rates 3.4 μmol/min g at Ti-hydroxide-oxide/Au, 4.0 μmol/min g at Ti-hydroxide-oxide/Pd and 4.1 μmol/min g at Ti-hydroxide-oxide/Pt were found. The activity of all TiO₂/Au, Pd and Pt catalysts increased by calcination at 600 °C from 50 to 100 %.     

One-step synthesis of nanocrystalline N-doped TiO2 powders and their photocatalytic activity under visible light irradiation

Nanocrystalline N-doped TiO₂ powders were successfully prepared by hydrothermal reaction for 2 h at low temperature (120 °C) and at an applied pressure of 3 MPa. The grain size of the powders (calculated by use of Scherrer’s method) ranged from 8.2 to 10.2 nm. The BET specific surface area ranged from 151.0 to 220.0 m²/g. A significant shift of the light absorption edge toward the visible light zone was observed in the UV–visible spectra. XPS results showed that nitrogen atoms were incorporated into the TiO₂ lattice. The photocatalytic activity of the synthesized N-doped TiO₂ powders was evaluated by measurement of photodegradation of methylene blue (MB) in aqueous solution under visible light irradiation. The amount of MB degraded increased with increasing illumination intensity.     

Au/TiO2 nanotube catalysts prepared by combining sol–gel method with hydrothermal treatment and their catalytic properties for CO oxidation

A new preparation method for Au/TiO₂ nanotubes (NTs) by combing sol–gel with hydrothermal treatment technique was developed. The TiO₂ NTs calcined at 300 °C were nearly uniform, and the gold particles were distributed homogeneously. The possible formation mechanism was suggested. The 5 % Au/TiO₂ NTs calcined at 300 °C had the best catalytic activity for CO oxidation, and their conversion of CO remained at 100 % during 60 h on stream. This preparation method could improve the thermal stability of Au/TiO₂ nanotube catalysts.     

Synthesis of nanostructured titania/zirconia membrane and investigation of its physical separation and photocatalytic properties in treatment of textile industries wastewater

Nanostructured TiO₂/ZrO₂ composite membranes with varying compositions were obtained by sol–gel technique. The influence of 0–30 mol% zirconia doping on microstructure, water permeability, photocatalytic and physical separation properties, removal of methyl violet of textile industries wastewater and thermal and mechanical stability of titania/zirconia composite membranes was described. Firstly, alumina supports were coated with TiO₂ intermediate layers using the colloidal sol–gel route. The TiO₂/ZrO₂ composite sols were prepared via a polymeric sol–gel method and dip-coated on TiO₂ intermediate layer. The samples were characterized by DLS, TG-DTA, XRD, FTIR, BET-BJH, UV–visible, SEM, TEM and AFM. It was shown that zirconia retards the phase transformation of anatase to rutile until at least 700 °C. The minimum pore size and maximum surface area obtained were 1.2 nm and 153 m²/g, respectively, attributed to the sample with 20 mol% zirconia. The mechanical strength of titania membranes was significantly improved by addition of zirconia. The most methyl violet removal efficiency obtained, with and without UV-irradiation, is 80.8 and 72.6%, respectively, attributed to the sample with 20 mol% zirconia.     

Effect of molten salt synthesis temperature on TiO<Subscript>2</Subscript> and Li cycling properties

In this project, we synthesized TiO₂ compounds through the molten salt method (MSM) using Ti(IV) oxysulfate, as the Ti source. Molten salts in the ratio of 0.375 M LiNO₃:0.180 M NaNO₃:0.445 M KNO₃ were added and heated at temperatures of 145, 280, 380, and 480 °C for 2 h in air, respectively. A part of the sample prepared at 145 °C was further reheated to 850 °C for 2 h in air. X-ray diffraction studies showed that the amorphous phase was obtained when the sample was prepared at 145 °C, and polycrystalline to crystalline anatase phase was formed when heated from 280 to 850 °C, which is complementary to the results of selected area electron diffraction studies. Electrochemical properties were studied using galvanostatic cycling, cyclic voltammetry, and electrochemical impedance spectroscopy at a current density of 33 mA g^?1 (0.1 C rate) and a scan rate of 0.058 mV s^?1, in the voltage range 1.0–2.8 V vs. Li. Electrochemical cycling profiles for the amorphous TiO₂ samples prepared at 145 °C showed single-phase reaction with a low reversible capacity of 65 mAh g^?1, whereas compounds prepared at 280 °C and above showed a two-phase reaction of Li-poor and Li-rich regions with a reversible capacity of 200 mAh g^?1. TiO₂ produced at 280 °C showed the lowest capacity fading and the lowest impedance value among the investigated samples.     

Extraction of pertechnetates from HNO<Subscript>3</Subscript> solutions into ionic liquids

The effect of the oxidation temperature of sintered UO₂ pellets on the powder properties of U₃O₈ was studied in the temperature range 250–900 °C in air. The U₃O₈ was obtained at 450 °C after 180 min and its particle size and surface area are respectively, 35 µm and 0.7 m²/g. The reduction of the U₃O₈ powder resulted in UO₂ after 30 min with a surface area of 0.8 m²/g. This value was improved more than 3.5 times by applying five alternating oxidation–reduction cycles.     

Thermal analysis of a white calcium bentonite

A white calcium bentonite (CaB) taken from Çaml?dere (Ankara, Turkey) region was heated at various temperatures between 100 and 1100 °C for 2 h. The mineralogy of the CaB was determined as calcium smectite (CaS), metahalloysite (MH), opal-A (OA), opal-CT (OCT), quartz (Q), feldspar (F), and calcite (C) using the X-ray diffraction patterns of the natural CaB and its heated samples. Besides the XRD patterns, the thermogravimetry, differential thermal analysis, and low-temperature nitrogen adsorption (N₂-AD) data show that the CaS lose adsorbed and hydration water up to 300 °C, dehydroxylation takes place between 300 and 750 °C, and then the 2:1 layer structure completely collapses above 900 °C. The activation energies for the dehydration and dehydroxylation were calculated as 7636 and 48838 J mol^?1, respectively, from the TG data using Coats and Redfern method. The specific surface area (S) and specific micro–mesopore volume (V) obtained from N₂-AD data were 44 m² g^?1 and 0.100 cm³ g^?1 for the natural CaB. S and V reach their maxima of 105 m² g^?1 and 0.155 cm³ g^?1, respectively, at 300 °C, remain approximately constant as the temperature increases up to 700 °C and then decrease almost in parallel with each other, reaching their minima at 900 °C. This indicates that the S and V values increase gradually during dehydration and dehydroxylation of the CaS.     

Preparation and nonlinear optical properties of Au nanoparticles doped TiO2 thin films

Nano-sized noble metal nanoparticles doped dielectric composite films with large third-order nonlinear susceptibility due to the confinement and the enhancement of local field were considered to be applied for optical information processing devices, such as optical switch or all optical logical gates. In this paper, sol–gel titania thin films doped with gold nanoparticles (AuNPs, ~10 nm in average size) were prepared. AuNPs were firstly synthesized from HAuCl₄ in aqueous solution at ~60 °C, using trisodium citrate as the reducing agent, polyvinylpyrrolidone as the stable agent; then the particle size and optical absorption spectra of the AuNPs in aqueous solutions were characterized by transmitting electron microscopy and UV–Vis–NIR spectrometry. Sol–gel 2AuNPs–100TiO₂ (in %mol) thin films (5 layers, ~1 μm in thickness) were deposited on silica glass slides by multilayer dip-coating. After heat-treated at 300–1,000 °C in air, the AuNPs–TiO₂ thin films were investigated by X-ray diffraction, scanning electron microscopy and atomic force microscopy. The nonlinear optical properties of the AuNPs–TiO₂ thin films were measured with the Z-scan technique, using a femtosecond laser (200 fs) at the wavelength of 800 nm. The third-order nonlinear refractive index and nonlinear absorption coefficient of 2AuNPs–100TiO₂ films were at the order of 10^?12 cm²/W, and the order of 10^?6 cm/W, respectively, and the third-order optical nonlinear susceptibility χ⁽³⁾ was ~6.88 × 10^?10 esu.     

Sol–gel preparation of mesoporous Al2O3–SiO2 glasses: structural evolution monitored by solid state NMR

Glasses along the composition line 0.5Al₂O₃–xSiO₂ (1 ≤ x ≤ 6) were prepared via a novel sol–gel route using tetraethylorthosilicate and aluminum lactate as precursors. The structural evolution from solution to gel to glass is monitored by standard ²⁷Al and ²⁹Si nuclear magnetic resonance (NMR) spectroscopies, revealing important insights about molecular level mechanisms occurring at the various stages of glass formation. Under the experimental conditions reported, silica and alumina precursors undergo homoatomic condensation processes when the gel is heat treated at about 100 and 300 °C, respectively, and only little heteroatomic co-condensation occurs in this temperature range. The latter is promoted only upon elimination of the residual lactate and water ligands upon annealing the gels above 300 °C. Following calcination at 650 °C, mesoporous glasses are obtained, having average pore diameter of about 3 nm and a surface areas near 500 m²/g. Si–O–Al connectivities are detected by ²⁹Si magic angle spinning (MAS)-NMR. ²⁷Al MAS-NMR spectra reveal aluminum in four-, five- and six-coordination. The spectra differ significantly from those of other sol–gel derived Al₂O₃–SiO₂ materials prepared from different precursor routes, suggesting that the lactate route results in a higher degree of compositional homogeneity.     

Optical, mechanical, and dielectric properties of Bi1/2Na1/2TiO3 thin film synthesized by sol–gel method

The Bi_1/2Na_1/2TiO₃ (BNT) thin film has been researched as an excellent candidate of lead-free ferroelectric materials. We synthesized BNT thin film on Si wafers or quartz glass by sol–gel spin coating method. The homogeneous and crack-free BNT thin film was synthesized by cost effective solution sol gel coating method. The main crystal phase of the film was identified as Bi_1/2Na_1/2TiO₃. The BNT thin film which was coated 3 times and heat-treated at 700 °C had about 70% of transmittance in the ultra-violet visible (UV–VIS) light wavelength region. The calculated band gap energies from the UV transmittance spectra were 3.0 and 3.5 eV for indirect and direct transition, respectively and the refractive index of BNT thin film was 2.16 at 898 nm of wavelength. The hardness and elastic modulus of the film were about 9 and 136 GPa at 10 mN load, where the penetration depth was about 220 nm. BNT thin film showed the diffuse type of dielectric properties due to its Na⁺ and Bi³⁺ ions in A′_1/2A″_1/2BO₃-type perovskite structure and the dielectric constant was about 10 until 300 °C and showed maximum value at 550 °C, 450 at 1 kHz.     

Adsorption of N719 Dye on Anatase TiO2 Nanoparticles and Nanosheets with Exposed (001) Facets: Equilibrium,Kinetic, and Thermodynamic Studies

Anatase TiO₂ nanosheets (TiO₂ NS) with dominant (001) facets and TiO₂ nanoparticles (TiO₂ NP) with dominant (101) facets are fabricated by hydrothermal hydrolysis of Ti(OC₄H₉)₄ in the presence and absence of hydrogen fluoride (HF), respectively. Adsorption of N719 onto the as‐prepared samples from ethanol solutions is investigated and discussed. The adsorption kinetic data are modeled using the pseudo‐first‐order, pseudo‐second‐order, and intraparticle diffusion kinetics equations, and indicate that the pseudo‐second‐order kinetic equation and intraparticle diffusion model can better describe the adsorption kinetics. Furthermore, adsorption equilibrium data of N719 on the as‐prepared samples are analyzed by Langmuir and Freundlich models; this suggests that the Langmuir model provides a better correlation of the experimental data. The adsorption capacities (q_max) of N719 on TiO₂ NS at various temperatures, determined using the Langmuir equation, are 65.2 (30 °C), 68.2 (40 °C), and 76.6 (50 °C) mg g⁻¹, which are smaller than those on TiO₂ NP, 92.4 (30 °C), 100.0 (40 °C), and 108.2 (50 °C) mg g⁻¹, respectively. The larger adsorption capacities of N719 for TiO₂ NP versus NS are attributed to its higher specific surface areas. However, the specific adsorption capacities (q_max/S_BET) at various temperatures are 1.5 (30 °C), 1.6 (40 °C), and 1.7 (50 °C) mg m⁻² for TiO₂ NS, which are otherwise higher than those for NP, 0.9 (30 °C), 1.0 (40 °C), and 1.1 (50 °C) mg m⁻², respectively. The larger specific adsorption capacities of N719 for TiO₂ NS versus NP are because the (001) surface is more reactive for dissociative adsorption of reactant molecules compared with (101) facets. Notably, the q_max and q_max/S_BET for both TiO₂ samples increase with increasing temperature, suggesting that adsorption of N719 on the TiO₂ surface is an endothermic process, which is further confirmed by the calculated thermodynamic parameters including free energy, enthalpy, and entropy of adsorption process. The present work will provide a new understanding on the adsorption process and mechanism of N719 molecules onto TiO₂ NS and NP, and this should be of great importance for enhancing the performance of dye‐sensitized solar cells.     

Solvothermal synthesis of large surface area zirconia

The reaction of zirconium n-propoxide in glycol at 300°C yielded microcrystalline tetragonal zirconia (ZrO₂). The crystallite size of the product depended on the carbon number of the glycol and increased in the following order (carbon number of glycol): 2<6<4, which suggested that the heterolytic cleavage of O-C bond of gylcoxide formed by transesterification is the prime factor for the formation of the product. In toluene, zirconium isopropoxide also gave tetragonal zirconia at 300°C, and zirconium tert-butoxide decomposed at 200°C yielding amorphous zirconia, while zirconium n-propoxide was stable at 300°C. These results suggest that the reaction in toluene depends on the structure of the alkyl group of the alkoxides. Thus-obtained tetragonal zirconias maintained large surface areas (90–160 m²/g) even after calcination at 500°C.     

Surfactant-Free Hydrothermal Synthesis of Mesoporous Niobia Samples and Their Photoinduced Decomposition of Terephthalic Acid (TPA)

This study introduces a low temperature surfactant-free hydrothermal method to synthesize mesoporous Nb₂O₅ photocatalysts using NbCl₅ and H₂O₂ as precursors that are subsequently calcinated at 300, 400 and 450 °C and are assigned as mNb₂O₅-300, mNb₂O₅-400 and mNb₂O₅-450, respectively. Commercial niobia sample was used as reference sample for comparison purpose. All of materials were characterized by XRD, SEM, UV–Vis DRS, FTIR, TG/DTG and BET techniques. The synthesized Nb₂O₅ particles especially mNb₂O₅-300 sample shows a high surface area (240 m²/g), a large pore volume (0.21 cm³/g) and an identifying morphology of these features. Photocatalytic decomposition of terephthalic acid was evaluated using UV–Vis spectrophotometer. The photocatalytic reactions followed pseudo-first-order kinetics with an apparent rate constant of k = 105 × 10^?3 min^?1 for mNb₂O₅-300 sample with the highest activity among all samples at natural pH (pH = 6). Meanwhile, it was observed that optimum pH of 4 resulted in fast photocatalytic reaction for mNb₂O₅-300 sample.     

Calcination temperature-dependent morphology of photocatalytic ZnO nanoparticles prepared by an electrochemical–thermal method

ZnO nanoparticles (NPs) with tunable morphologies were synthesized by a hybrid electrochemical–thermal method at different calcination temperatures without the use of any surfactant or template. The NPs were characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction, dynamic light scattering, thermogravimetry–differential thermal analysis, scanning electron microscope and N₂ gas adsorption–desorption studies. The FT-IR spectra of ZnO NPs showed a band at 450 cm^?1, a characteristic of ZnO, which remained fairly unchanged at calcination temperatures even above 300 °C, indicating complete conversion of the precursor to ZnO. The products were thermally stable above 300 °C. The ZnO NPs were present in a hexagonal wurtzite phase and the crystallinity of ZnO increased with an increasing calcination temperature. The ZnO NPs calcined at lower temperature were mesoporous in nature. The surface areas of ZnO NPs calcined at 300 and 400 °C were 51.10 and 40.60 m² g^?1, respectively, which are significantly larger than commercial ZnO nanopowder. Surface diffusion has been found to be the key mechanism of sintering during heating from 300 to 700 °C with the activation energy of sintering as 8.33 kJ mol^?1. The photocatalytic activity of ZnO NPs calcined at different temperatures evaluated by photocatalytic degradation of methylene blue under sunlight showed strong dependence on the surface area of ZnO NPs. The ZnO NPs with high surface area showed enhanced photocatalytic activity.     

Sol–gel synthesized vanadium doped TiO2 photocatalyst: physicochemical properties and visible light photocatalytic studies

Vanadium doped titanium dioxide (V–TiO₂) photocatalyst was synthesized by the sol–gel method using ammonium vanadate as vanadium source. The prepared samples were characterized by XRD, N₂ adsorption–desorption method, UV–Vis DRS, Fourier transform infrared (FTIR), scanning electron microscope–energy dispersive X-ray and photoluminescence (PL) analysis. The results show that V⁵⁺ ions were successfully incorporated into the crystal lattice of TiO₂ as a consequence, not only an obvious decrease in the band gap and a red shift of the absorption threshold into the visible light region was recorded for the V modified TiO₂, but, also a decrease in photogenerated electrons and holes recombination rate was observed as demonstrated by PL analysis. FTIR study indicated that in undoped TiO₂ sample the acetate group favored a bidentate bridging mode of binding with titanium atoms, whereas a bidentate chelating mode of linkage was observed in V–TiO₂ powders. The crystallite size of the samples calcined at 300 and 500 °C were decreased beyond the molar ratio of 200:1 (V:Ti), this may be due to dopant presence in the grain boundaries hindering the crystal growth. The photocatalytic activities for both pure and vanadium doped TiO₂ powders were tested in the discoloration of a reactive dyestuff, methylene blue, under visible light. The 100:1 (V:Ti) doped photocatalyst, calcined at 300 °C showed enhanced photocatalytic activity under visible light with a rate constant (k_obs) of 5.024 × 10^?3 min^?1 which is nearly five times higher than that of pure TiO₂, as result of low band gap value, high specific surface area and a decrease in recombination rate.