Green synthesis of graphene nanosheets/ZnO composites and electrochemical properties

A green and facile approach was demonstrated to prepare graphene nanosheets/ZnO (GNS/ZnO) composites for supercapacitor materials. Glucose, as a reducing agent, and exfoliated graphite oxide (GO), as precursor, were used to synthesize GNS, then ZnO directly grew onto conducting graphene nanosheets as electrode materials. The small ZnO particles successfully anchored onto graphene sheets as spacers to keep the neighboring sheets separate. The electrochemical performances of these electrodes were analyzed by cyclic voltammetry, electrochemical impedance spectrometry and chronopotentiometry. Results showed that the GNS/ZnO composites displayed superior capacitive performance with large capacitance (62.2 F/g), excellent cyclic performance, and maximum power density (8.1 kW/kg) as compared with pure graphene electrodes. Our investigation highlight the importance of anchoring of small ZnO particles on graphene sheets for maximum utilization of electrochemically active ZnO and graphene for energy storage application in supercapacitors.     

The preparation of PANI/CA composite electrode material for supercapacitors and its electrochemical performance

Polyaniline (PANI)/carbon aerogel (CA) composite electrode materials were prepared by chemical oxidation polymerization. The morphology of PANI/CA composite was examined by scanning electron microscopy. The results showed that PANI was uniformly deposited onto the surface of porous CA and filled big inner pores of the CA. Electrochemical performance of the composite electrode was studied by cyclic voltammograms and galvanostatic charge/discharge measurements. The results indicated that the PANI/CA composite electrode had much better electrochemical performance, high reversibility, and high charge/discharge properties than CA. Moreover, the results based on cyclic voltammograms showed that the composite material has a high specific capacitance of 710.7 F g⁻¹, while the capacitance of CA electrode was only 143.8 F g⁻¹. Besides, the supercapacitor using the PANI/CA composite as electrode active material showed a stable cycle life in the potential range of −0.2–0.8 V.     

电弧放电法制备石墨烯的硝酸改性及其电化学性能增强

采用电弧放电法大规模制备了层数少, 导电率高, 结晶性好的石墨烯纳米片(GNSs). 通过扫描电镜(SEM)和透射电镜(TEM)表征发现制得的石墨烯形貌良好. 然而电化学测试表明GNSs作为电极材料的电容性能不好. 为了增加材料表面电化学反应活性点, 促进GNSs在水系电解液中的润湿性, 我们对所制备的GNSs表面进行了硝酸改性处理. 结果显示硝酸处理后的石墨烯纳米片(H-GNSs)表面新增了较多的含氧氮官能团,其亲水性得到了显著提高. 对H-GNSs的电化学研究表明: 硝酸改性处理后的GNSs在2 mol·L^-1 KOH溶液中电流密度为0.5 A·g^-1时, 比电容可达65.5 F·g^-1, 约为改性前的30 倍; 此外, H-GNSs作为电极材料连续进行2000次充放电测试后还展示出了良好的循环稳定性, 是一种潜在的超级电容器电极材料.     

Hydrothermal synthesis of reduced graphene sheets/Fe2O3 nanorods composites and their enhanced electrochemical performance for supercapacitors

Reduced graphene nanosheets/Fe₂O₃ nanorods (GNS/Fe₂O₃) composite has been fabricated by a hydrothermal route for supercapacitor electrode materials. The obtained GNS/Fe₂O₃ composite formed a uniform structure with the Fe₂O₃ nanorods grew on the graphene surface and/or filled between the graphene sheets. The electrochemical performances of the GNS/Fe₂O₃ hybrid supercapacitor were tested by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests in 6 M KOH electrolyte. Comparing with the pure Fe₂O₃ electrode, GNS/Fe₂O₃ composite electrode exhibits an enhanced specific capacitance of 320 F g⁻¹ at 10 mA cm⁻² and an excellent cycle-ability with capacity retention of about 97% after 500 cycles. The simple and cost-effective preparation technique of this composite with good capacitive behavior encourages its potential commercial application.     

CuO/GNS复合材料的制备及其电化学性能

利用改进的Hummers 法制备GO,采用化学沉淀法合成CuO/GNS复合材料,用X 射线衍射(XRD)、扫描电镜(FESEM)、比表面积测试(BET)等表征了产物的组成、结构和形貌;用循环伏安、恒电流充放电等测试方法对复合材料的电化学性能进行了研究。结果显示：在这种复合材料中,石墨烯作为导电骨架,有利于增加氧化铜颗粒之间的导电性和材料的机械稳定性。大电流放电表现出优异的电化学性能,在 10 A.g_-1的电流密度下复合材料的比电容仍可达 276 F.g_-1,1000 次循环后比电容仍能保持86.5%,呈示该复合材料具有优异的电化学性能。     

石墨烯/钴镍双氢氧化物复合材料的制备及其超电容特性

采用氧化石墨(GO)还原法制备石墨烯(GNS),以氨水为沉淀剂,在石墨烯存在的情况下,通过Co²⁺和Ni²⁺化学共沉积的方法合成了石墨烯/钴镍双氢氧化物复合电极材料,采用红外光谱(FT-IR)、X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、比表面积测试(BET)等技术手段表征了产物的组成、结构和形貌,用循环伏安、恒电流充放电等测试方法对复合材料的电化学性能进行了研究。 研究发现,石墨烯纳米片均匀分散在钴镍双氢氧化物中,改善了钴镍双氢氧化物的传导性和结构稳定性。 电化学测试表明,在1 A/g的电流密度下,复合材料比电容高达2770 F/g,且循环500次后,比电容仍能保持93.4%,呈示该复合材料具有优异的电化学性能。     

Electrochemical performance of Co–Al layered double hydroxide nanosheets mixed with multiwall carbon nanotubes

Regular hexagonal Co–Al layered double hydroxides (Co–Al LDH) were synthesized by urea-induced homogeneous precipitation. This material proved to be nanosheets by scanning electron microscopy and X-ray diffraction measurements. The electrochemical capacitive behavior of the nanosheets in 1 M KOH solution were evaluated by constant current charge/discharge and cyclic voltammetric measurements, showing a large specific capacitance of 192 F·g⁻¹ even at the high current density of 2 A·g⁻¹. When multiwall carbon nanotubes (MWNTs) were mixed with the Co–Al LDH, it was found that the specific capacitance and long-life performance of all composite electrodes at high current density are superior to pure LDH electrode. When the added MWNTs content is 10 wt%, the specific capacitance increases to 342.4 F·g⁻¹ and remains at a value of 304 F·g⁻¹ until the 400th cycle at 2 A·g⁻¹, showing that this is a promising electrode material for supercapacitors working at heavy load. According to the electrochemical impedance spectra, MWNTs greatly increase the electronic conductivity between MWNTs and the surface of Co–Al LDH, which consequently facilitates the access of ions in the electrolyte and electrons to the electrode/electrolyte interface.     

Nitrogen-doped porous carbon coated on MnCo2O4 nanospheres as electrode materials for high-performance asymmetric supercapacitors

Spinel-based nanostructured materials are commonly used as promising electrode materials for supercapacitor applications. The combination of heteroatom-doped carbon material with spinel oxides substantially improves the specific capacitance and cyclic stability. In this work, dopamine-derived nitrogen-doped carbon was coated on spinel phase MnCo₂O₄ nanospheres using simple solvothermal and calcination methods. Surface morphology and the crystalline structure of the prepared MnCo₂O₄@Nitrogen-doped carbon were confirmed by FESEM and X-ray diffraction. The electrochemical performance of MnCo₂O₄@Nitrogen-doped carbon electrode material was analyzed by cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance spectroscopy techniques. MnCo₂O₄@nitrogen-doped carbon exhibits the highest specific capacitance of 1200 F/g compared to MnCo₂O₄ spheres are 726 F/g at 1 A/g and exhibits excellent cyclic stability (capacitance retention of 87% at 7 A/g after 3000 cycles). The enhanced performance of the composite might be benefitted from the synergistic effect between nitrogen-doped carbon on porous MnCo₂O₄ spheres. Furthermore, an asymmetric supercapacitor device was fabricated by using the optimized composition of MnCo₂O₄@NC-2 as a positive electrode and nitrogen, sulfur-doped reduced graphene oxide (NS-rGO) as a negative electrode, respectively. This asymmetric supercapacitor device achieves a maximum energy density of 61.0 Wh/kg at a power density of 2889 W/kg and possesses excellent capacitance retention of 95% after 5000 cycles at 7 A/g.     

Preparation and performances of carbon aerogel microspheres for the application of supercapacitor

Carbon aerogel (CA) microspheres were successfully synthesized by an inverse emulsion polymerization routine. Morphology and physical properties of the CA microspheres were characterized by scanning electron microscopy, N₂ sorption isotherm, and transmission electron microscopy. The results showed that the CA microspheres were all fine spheres with diameters about 4 μm, and the CA microsphere was a typical mesoporous material with ordered mesoporous nano-network structure. The maximum capacitance of the electrode obtained from cyclic voltammetry was 187.08 F/g and the capacitance of the supercapacitor resulted from galvanostatic charge–discharge tests was up to 45.98 F/g. The supercapacitor using CA microsphere as electrode material presented a long cycle life, high charge–discharge efficiency, and low R _s of 0.70 Ω in 6 M KOH electrolyte.     

Synthesis and Electrochemical Performance of Co3O4/Graphene

Co3O4/reduced graphene oxide composites were synthesized via a simple electrochemical method from graphene oxide and Co（NO3）2·6H2O as raw materials.Co3O4 nanoparticles with sizes of around 30-50 nm were distributed on the surface of graphene nanosheets confirmed by scanning electron microscopy and transmission electron microscopy.Electrochemical properties of Co3O4/graphene composite were tested by cyclic voltammetry,galvanostatic charge-discharge,and electrochemical impedance spectroscopy.The Co3O4/reduced graphene oxide composite was used as the pseudocapacitor electrode in the 2 mol/L NaOH aqueous electrolyte solution.The Co3O4/reduced graphene oxide composite electrode exhibited a specific capacitance of 357 F/g at a current density of 0.5 A/g in a three-electrode system.72％ of capacitance was retained when the current density increased to 3 A/g.The Co3O4/reduced graphene oxide composite prepared electrodes show a high rate capability and excellent long-term stability.After 1000 cycles of charge and discharge,the capacitance is still maintained 87％ at a current density of 1 A/g,indicating that the composite is a oromising alternative electrode material used for supercapacitors.     

Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Three-dimensional bundle-like multiwalled carbon nanotubes composite for supercapacitor electrode application

Bundle-type mutil-walled carbon nanotubes (MWCNTs) composite electrode is the first investigation and publication for the supercapacitor application. According to the thermogravimetric analysis results, as-synthesized BCNTs are considered as the electrode materials for supercapacitors and electrochemical double-layer capacitor in this study. The Brunauer–Emmett–Teller specific surface area of as-prepared bundled carbon nanotubes (BCNTs) is 95.29 m²/g given to a type III isotherm and H3 hysteresis loops. Slow scanning rates promote and enhance to achieve high C_b because of the superior conductivity of CNT bundles and one side close-layered Ni/Mg/Mo alloy inside the BCNT-based electrode and facile electron diffusivity between electrolyte and electrode. The specific capacitance C_s (1,560 F/g) is nearly equal to the maximum specific capacitance, which the BCNT-based composite electrode can actually be able to charge or fill in. The maximum energy density value is 195 Wh/kg with corresponding power density values of 0.21 kW/kg. Furthermore, the active 3D BCNTs material fabricated electrode enhances to contact the electrolyte directly and decreases the ion diffusion limitation. Electrochemical impedance spectroscopy spectrum summarized as the low-frequency area controls by mass transfer limitation, and the high-frequency area dominates by charge transfer of kinetic control. After 2,000 consecutive cyclic voltammetry sacnings and galvanostatic charge-discharge cycles at a current density of 1.67 A/g performs, the specific capacitance retentions of 3D BCNTs electrodes achieved 128.2 and 77.3%, respectively. Three-dimensional BCNT composite electrodes exhibit good conductivity and low charge transfer resistance, which is beneficial to fast charge transfer between the BCNTs electrode materials and electrolytes.     

A Co(OH)2−graphene nanosheets composite as a high performance anode material for rechargeable lithium batteries

A Co(OH)₂?graphene nanosheets (Co(OH)₂?GNS) composite as a high performance anode material was firstly prepared through a simultaneous hydrothermal method. The structure, morphology and electrochemical performance of the obtained samples were systematically investigated by X-ray diffraction (XRD), transmission electron microscope (TEM) and electrochemical measurements. According to the TEM analysis, the surface of the Co(OH)₂ is surrounded with GNS in the Co(OH)₂?GNS composite. The specific discharge (lithiation) and charge (delithiation) capacities of Co(OH)₂?GNS attain to 1599 and 1120 mAh/g at a current density of 200 mA/g in the first cycle, respectively. After 30 cycles, the reversible capacity of Co(OH)₂?GNS is still 910 mAh/g with the retention of 82%. The particular structure of Co(OH)₂ particles surrounded by the GNS could limit the volume change during cycling and provide an excellent electronic conduction pathway, which could be the main reason for the remarkable improvement of electrochemical performance.     

The preparation and performance of flocculent polyaniline/carbon nanotubes composite electrode material for supercapacitors

Polyaniline (PANI)/carbon nanotubes (CNTs) composite electrode material was prepared by in situ chemical polymerization. The structure and morphology of PANI/CNTs composite are characterized by Fourier infrared spectroscopy, scanning electron microscope, and transmission electron microscopy. It has been found that a flocculent PANI was uniformly deposited on the surface of CNTs. The supercapacitive behaviors of the PANI/CNTs composite materials are investigated with cyclic voltammetry, galvanostatic charge/discharge, impedance, and cycle life measurements. The results show that the PANI/CNTs composite electrodes have higher specific capacitances than CNT electrodes and better stability than the conducting polymers. The capacitance of PANI/CNTs composite electrode is as high as 837.6 F g⁻¹ measured by cyclic voltammetry at 1 mV s⁻¹. Besides, the capacitance retention of coin supercapacitors remained 68.0% after 3,000 cycles.     

肝素钠掺杂球状聚吡咯的合成及其电化学电容

以生物制剂肝素钠为掺杂剂,由自组装方法合成出平均粒径为100 nm的球状聚吡咯(PPy),用作超级电容器电极材料.透射电镜(TEM)、循环伏安、恒流充放电和电化学交流阻抗测试表明,肝素钠掺杂聚吡咯呈现较好的形貌和电容性质,在电流密度3 mA/cm2下充放电,单电极比电容达到338 F/g.     

一步固相球磨法制备二硫化钼/石墨二维复合材料及其储锂性能

以商品化二硫化钼(MoS_2)和石墨为原料,首次通过一步固相球磨法制备了MoS_2/石墨二维复合材料。X射线衍射(XRD)、扫描电子显微镜(SEM)和能谱(EDS)测试结果表明,本体MoS_2和石墨在高速固相球磨过程中同时被剥离成较薄的片层,且剥离后的石墨片层均匀分散在MoS_2片层中。制备的MoS_2/石墨复合材料表现出优异的循环稳定性和倍率性能,其中,MoS_2/石墨(质量比7∶3)复合材料在100 mA/g电流密度下,首圈放电比容量801 mA·h/g,充放电循环100圈后仍保持在694 mA·h/g,远优于商品化的本体MoS_2(约110 mA·h/g)。这主要归功于球磨后得到的石墨片层不仅能提高复合材料的导电性,还能有效地抑制MoS_2片层团聚,保持材料的结构稳定性。该方法简便易行、成本低,适合于高性能锂离子电池电极材料的规模化制备。     

碳纳米管/聚苯胺/石墨烯复合纳米碳纸及其电化学电容行为

通过真空抽滤的方法制备碳纳米管纸,并对其进行循环伏安电化学氧化处理.以该电化学氧化处理的碳纳米管(CV-CNT)纸为基体,采用电化学聚合沉积聚苯胺(PANI),随后吸附石墨烯(GR),制备具有三明治夹心结构的碳纳米管/聚苯胺/石墨烯(CV-CNT/PANI/GR)复合纳米碳纸.该结构外层为GR,内层由PANI包裹的CNT形成网络骨架,充分发挥三者各自优势构建柔性电极材料.用场发射扫描电镜(FE-SEM)、透射电子显微镜(TEM)、拉曼光谱对其形貌与结构进行表征,并测试其电化学性能.研究发现:PANI呈纳米晶须状,并均匀包裹在CV-CNT表面;该复合碳纸具有良好的电容特性、大电流充放电特性以及良好的循环稳定性能.电流密度为0.5A·g-1时,比电容可达415F·g-1;20A·g-1时仍能保持106F·g-1的比电容.由于GR的保护作用,1000次循环之后较CV-CNT/PANI保持更高的有效比电容.该CV-CNT/PANI/GR复合碳纸展现出在高性能超级电容器柔性电极材料的潜在应用价值.     

氨蒸发诱导法制备纳米结构LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2及其作为高功率型锂离子电池正极材料的性能

采用氨蒸发诱导法成功制备出纳米结构LiNi1/3Co1/3Mn1/3O2正极材料,借助X射线衍射(XRD)分析、扫描电镜(SEM)、透射电镜(TEM)、高分辨率透射电镜(HRTEM)、能量分散谱(EDS)和比表面测试等表征手段及恒电流充放电测试研究了其晶体结构、微观形貌和电化学性能.研究表明该方法制备出的材料具有良好的α-NaFeO2层状结构,阳离子混排程度低.纳米片交错堆积而成核桃仁状形貌,片与片之间形成许多纳米孔,而且纳米片的侧面属于{010}活性面,能够提供较多的锂离子的脱嵌通道.在室温下及3.0-4.6 V充放电范围内,该材料在电流密度为0.5C、1C、3C、5C和10C时放电比容量分别为172.90、153.95、147.09、142.16和131.23mAh?g-1.说明其具有优异的电化学性能,非常有潜力用于动力汽车等高功率密度锂离子电池中.     

Fabrication of high-performance supercapacitor using date leaves-derived submicron/nanocarbon

Offering a suitable and low-cost electrode material is one of the most important and challenging demands in supercapacitor research. In this aspect, carbon prepared from biomass by simply pyrolysis and ball milling could be one ideal electrode material for supercapacitor applications. Hence, a novel type of submicron/nanocarbon was prepared from date leaves by simple pyrolysis and ball milling. After morphological and chemical characterizations, the prepared carbon was used as the electrode material upon immobilizing on a steel substrate (current collector) to fabricate a high-performance symmetric supercapacitor. The fabricated supercapacitor took advantage of the carbon's electric double layer capacitance behaviour and pseudocapacitance behaviour of heteroatoms present in the carbon. The developed supercapacitor device provides significant charging/discharging using the optimum electrolyte (0.1 M sulfuric acid). That manifested with a high specific capacitance of (～107 F/g) and maintained above 92% of its initial capacitance after 1000 charge/discharge cycles. Furthermore, the supercapacitor provides an energy density of ～10 Wh/Kg at a power density of ～200 W/Kg. This work provides an inexpensive, high-performance supercapacitor that depends on the biomass (date palm leaves) and nominates it as a capable candidate for mass-product in the future.     

高功率超级电容器用介孔炭电极材料

以纳米CaCO3为模板、蔗糖为前躯体制备超级电容器用介孔炭电极材料.材料的结构由氮吸附、TEM表征,借助恒流充放电、循环伏安和交流阻抗评价了其在6 mol.L-1KOH电解液中的电化学电容性能.结果表明,蔗糖基介孔炭的比表面积606 m2/g,富含10~30 nm的介孔.恒流放电法测得介孔炭在电流密度50 mA/g下的比电容为125 F/g,大电流倍率性能特别突出.电流密度增大到20 000 mA/g,比电容还保持有88F/g,远高于进口电容炭,该介孔炭是一种很有前景的高功率超级电容器炭电极材料.