Multi-scale analysis on the pulverized coal flow behaviors under high pressure dense-phase pneumatic conveying

To deeply knowledge of the flow behaviors of pulverized coal particles in dense gas-solid two-phase flow,a multi-scale analysis method based on electrostatic se...     

Numerical study of elbow erosion due to sand particles under annular flow considering liquid entrainment

Sand particle erosion is always a challenge in natural gas production. In particular, the erosion in gas–liquid–solid annular flow is more complicated. In this study, a three-phase flow numerical model that couples the volume of fluid multiphase flow model and the discrete phase model was developed for prediction of erosion in annular flow. The ability of the numerical model to simulate the gas–liquid annular flow is validated through comparison with the experimental data. On the basis of the above numerical model, the phase distribution in the pipe was analyzed. The liquid entrainment behavior was reasonably simulated through the numerical model, which guaranteed the accuracy of predicting the particle erosion. Additionally, four erosion prediction models were used for the erosion calculation, among them, the Zhang et al. erosion model predicted the realistic results. Through the analysis of the particle trajectory and the particle impact behavior on the elbow, the cushion effect of the liquid film on the particles and the erosion morphology generation at the elbow were revealed.     

气固多相反应流中的煤粉颗粒相能量方程

为了合理地预测燃烧装置内煤粉颗粒的燃烧行为,从多相反应流中一般形式的颗粒相能量方程出发,导出了煤粉颗粒相的能量方程,给出了方程中反映相变引起的气固相间相互作用的源相的具体表达式,与此同时还给出了气相能量方程中代表相间相互作用的颗粒源项的一种计算式．     

Cold flow experiments in an entrained flow gasification reactor with a swirl-stabilized pulverized biofuel burner

Short particle residence time in entrained flow gasifiers demands the use of pulverized fuel particles to promote mass and heat transfer, resulting high fuel conversion rate. The pulverized biomass particles have a wide range of aspect ratios which can exhibit different dispersion behavior than that of spherical particles in hot product gas flows. This results in spatial and temporal variations in temperature distribution, the composition and the concentration of syngas and soot yield. One way to control the particle dispersion is to impart a swirling motion to the carrier gas phase. This paper investigates the dispersion behavior of biomass fuel particles in swirling flows. A two-phase particle image velocimetry technique was applied to simultaneously measure particle and gas phase velocities in turbulent isothermal flows. Post-processed PIV images showed that a poly-dispersed behavior of biomass particles with a range of particle size of 112–160 µm imposed a significant impact on the air flow pattern, causing air flow decelerated in a region of high particle concentration. Moreover, the velocity field, obtained from individually tracked biomass particles showed that the swirling motion of the carrier air flow gives arise a rapid spreading of the particles.     

Fully resolved simulations of viscoelastic suspensions by an efficient immersed boundary-lattice Boltzmann method

An efficient immersed boundary-lattice Boltzmann method (IB-LBM) is proposed for fully resolved simulations of suspended solid particles in viscoelastic flows. Stress LBM based on Giesekus and Oldroyd-B constitutive equation are used to model the viscoelastic stress tensor. A boundary thickening-based direct forcing IB method is adopted to solve the particle–fluid interactions with high accuracy for non-slip boundary conditions. A universal law is proposed to determine the diffusivity constant in a viscoelastic LBM model to balance the numerical accuracy and stability over a wide range of computational parameters. An asynchronous calculation strategy is adopted to further improve the computing efficiency. The method was firstly applicated to the simulation of sedimentation of a single particle and a pair of particles after good validations in cases of the flow past a fixed cylinder and particle migration in a Couette flow against FEM and FVM methods. The determination of the asynchronous calculation strategy and the effect of viscoelastic stress distribution on the settling behaviors of one and two particles are revealed. Subsequently, 504 particles settling in a closed cavity was simulated and the phenomenon that the viscoelastic stress stabilizing the Rayleigh–Taylor instabilities was observed. At last, simulations of a dense flow involving 11001 particles, the largest number of particles to date, were performed to investigate the instability behavior induced by elastic effect under hydrodynamic interactions in a viscoelastic fluid. The elasticity-induced ordering of the particle structures and fluid bubble structures in this dense flow is revealed for the first time. These simulations demonstrate the capability and prospects of the present method for aid in understanding the complex behaviors of viscoelastic particle suspensions.     

大速差射流燃烧室中烟煤与贫煤燃烧的数值模拟

本文基于颗粒相的轨道模型,对大速差射流燃烧室中烟煤粉与贫煤粉的二维流动,混合及燃烧进行了数值模拟,模拟结果从两相耦合的角度,阐明了煤粉颗粒在燃烧室中运动的规律,煤粉与大速差射流诱导的中心气体逆流之间的混合及其对煤粉火焰稳定的影响,指出此种燃烧室中煤粉火焰稳定的回流区燃烧机理,气相流场及回流区的预报结果与实验符合良好。     

Numerical evaluation of turbulence models for dense to dilute gas–solid flows in vertical conveyor

A two-fluid model (TFM) of multiphase flows based on the kinetic theory and small frictional limit boundary condition of granular flow was used to study the behavior of dense to dilute gas–solid flows in vertical pneumatic conveyor. An axisymmetric 2-dimensional, vertical pipe with 5.6 m length and 0.01 m internal diameter was chosen as the computation domain, same to that used for experimentation in the literature. The chosen particles are spherical, of diameter 1.91 mm and density 2500 kg/m³. Turbulence interaction between the gas and particle phases was investigated by Simonin's and Ahmadi's models and their numerical results were validated for dilute to dense conveying of particles. Flow regimes transition and pressure drop were predicted. Voidage and velocity profiles of each phase were calculated in radial direction at different lengths of the conveying pipe. It was found that the voidage has a minimum, and gas and solid velocities have maximum values along the center line of the conveying pipe and pressure drop has a minimum value in transition from dense slugging to dilute stable flow regime. Slug length and pressure fluctuation reduction were predicted with increasing gas velocity, too. It is shown that solid phase turbulence plays a significant role in numerical prediction of hydrodynamics of conveyor and the capability of particles turbulence models depends on tuning parameters of slip-wall boundary condition.     

Dual characters of interaction between particles and fluid

The unique characteristics of gas-solids two-phase flow and fluidization in terms of the flow structures and the apparent behavior of particles and fluid-particle interactions are closely linked to physical properties of the particles, operating conditions and bed configurations. Fluidized beds behave quite differently when solid properties, gas velocities or vessel geometries are varied. An understanding of hydrodynamic changes and how they, in turn, influence the transfer and reaction characteristics of chemical and thermal operations by variations in gas-solid contact, residence time, solid circulation and mixing and gas distribution is very important for the proper design and scale-up of fluidized bed reactors. In this paper, rather than attempting a comprehensive survey, we concentrate on examining some important positive and negative impacts of particle sizes, bubbles, clusters and column walls on the physical and chemical aspects of chemical reactor performance from the engineering application point of view with the aim of forming an adequate concept for guiding the design of multiphase fluidized bed chemical reactors.One unique phenomenon associated with particle size is that fluidized bed behavior does not always vary monotonically with changing the average particle size. Different behaviors of particles with difference sizes can be well understood by analyzing the relationship between particle size and various forces. For both fine and coarse particles, too narrow a distribution is generally not favorable for smooth fluidization. A too wide size distribution, on the other hand, may lead to particle segregation and high particle elutriation. Good fluidization performance can be established with a proper size distribution in which inter-particle cohesive forces are reduced by the lubricating effect of fine particles on coarse particles for Type A, B and D particles or by the spacing effect of coarse particles or aggregates for Type C powders.Much emphasis has been paid to the negative impacts of bubbles, such as gas bypassing through bubbles, poor bubble-to-dense phase heat & mass transfer, bubble-induced large pressure fluctuations, process instabilities, catalyst attrition and equipment erosion, and high entrainment of particles induced by erupting bubbles at the bed surface. However, it should be noted that bubble motion and gas circulation through bubbles, together with the motion of particles in bubble wakes and clouds, contribute to good gas and solids mixing. The formation of clusters can be attributed to the movement of trailing particles into the low-pressure wake region of leading particles or clusters. On one hand, the existence of down-flowing clusters induces strong solid back-mixing and non-uniform radial distributions of particle velocities and holdups, which is undesirable for chemical reactions. On the other hand, the formation of clusters creates high solids holdups in the riser by inducing internal solids circulations, which are usually beneficial for increasing concentrations of solid catalysts or solid reactants.Wall effects have widely been blamed for complicating the scale-up and design of fluidized-bed reactors. The decrease in wall friction with increasing the column diameter can significantly change the flow patterns and other important characteristics even under identical operating conditions with the same gas and particles. However, internals, which can be considered as a special wall, have been used to improve the fluidized bed reactor performance.Generally, desirable and undesirable dual characteristics of interaction between particles and fluid are one of the important natures of multiphase flow. It is shown that there exists a critical balance between those positive and negative impacts. Good fluidization quality can always be achieved with a proper choice of right combinations of particle size and size distribution, bubble size and wall design to alleviate the negative impacts.     

Multi-scale Fractured Coal Gas–Solid Coupling Model and Its Applications in Engineering Projects

With coal mining entering the geological environment of “high stress, rich gas, strong adsorption and low permeability,” the difficulty of joint coal and gas extraction clearly augments, the risk of solid–gas coupling dynamic disasters greatly increases, and the underlying mechanisms become more complex. In this paper, based on the characteristics of coal’s multi-scale structure and spatiotemporal variation, the multi-scale fractured coal gas–solid coupling model (MSFM) was built. In this model, the interaction between coal matrix and its fractures and the mechanical characteristics of gas-bearing coal were considered, as well as their coupling relationship. By MATLAB software, the stress–damage–seepage numerical computation programs were developed, which were applied into Comsol Multiphysics to simulate gas flow caused by coal mining. The simulation results showed the spatial variability of coal elastic modulus and cross-flow behaviors of coal seam gas, which were superior to the results of traditional gas–solid coupling model. And the numerical results obtained from MSFM were closer to the measured results in field, while the computation results of traditional model were slightly higher than the measured results. Furthermore, the MSFM in a large scale was verified by field engineering project.     

气固两相流介尺度LBM-DEM模型

LBM-DEM耦合方法通常是指一种颗粒流体系统直接数值模拟算法,即是一种不引入经验曳力模型的计算方法,颗粒尺寸通常比计算网格的长度大一个量级,颗粒的受力通过表面的粘性力与压力积分获得,其优点是能描述每个颗粒周围的详细流场,产生详细的颗粒-流体相互作用的动力学信息,可以探索颗粒流体界面的流动、传递和反应的详细信息及两相相互作用的本构关系,但其缺点是计算量巨大,无法应用于真实流化床过程模拟。本文针对气固流化床中的流体以及固体颗粒间的多相流体力学行为,建立了一种稠密气固两相流的介尺度LBMDEM模型,即LBM-DEM耦合的离散颗粒模型,实现在颗粒尺度上流化床的快速离散模拟。该耦合模型采用格子玻尔兹曼方法(LBM)描述气相的流动和传递行为,离散单元法(DEM)用于描述颗粒相的运动,并利用能量最小多尺度(EMMS)曳力解决气固耦合不成熟问题,以提高其模拟精度。通过经典快速流态化的模拟,验证了介尺度LBM-DEM耦合模型的有效性。模拟结果表明介尺度LBM-DEM模型是一种探索实验室规模气固系统的有力手段。     

稠密气固两相流各向异性颗粒相矩方法

基于气体分子动力学和颗粒动理学方法,考虑颗粒速度脉动各向异性,建立颗粒相二阶矩模型.应用初等输运理论,对三阶关联项进行模化和封闭.考虑颗粒与壁面之间的能量传递和交换,建立颗粒相边界条件模型.采用Koch等计算方法模拟气固脉动速度关联矩.考虑气体-颗粒间相互作用,建立稠密气体-颗粒流动模型.数值模拟提升管内气固两相流动特性,模拟结果表明提升管内颗粒相湍流脉动具有明显的各向异性.预测颗粒速度、浓度和颗粒脉动速度二阶矩与Tartan等实测结果相吻合.模拟结果表明轴向颗粒速度脉动强度约为平均颗粒相脉动强度的1.5倍,轴向颗粒脉动能大约是径向颗粒脉动能3.0倍.     

Flow characterization of high-pressure dense-phase pneumatic conveying of coal powder using multi-scale signal analysis

Flow characterization of high-pressure dense-phase pneumatic conveying of coal powder is not fully understood. To further reveal the dynamic behavior of coal particles in dense-phase pneumatic conveying pipelines, a method for the scale decomposition of particle motion based on empirical mode decomposition and Hurst analysis of experimental electrostatic signals is reported. This allows the multi-scale motion characteristics of single coal particles and particle clusters to be determined. Micro-, meso-, and macro-scale subsets were reconstructed, which reflected the different behaviors of the coal particles: specifically, dynamic features of the micro-scale subset represented features of single particle collisions and frictional interactions; dual fractal characteristics of the meso-scale subset described the motion of coal particle clusters; and features of the macro-scale subset reflected persistent dynamic behavior of the entire pneumatic conveying system. Motion behavior of single particles and particle clusters could be respectively investigated by considering the relative energies of the micro- and meso-scale contributions to the electrostatic signal. This was verified both by theoretical analysis and experiment.     

PIV measurement of particle motion in spiral gas–solid two-phase flow

With a concise review on some basic and novel algorithms and methods for the techniques of particle-imaging velocimetry (PIV), the paper reports an application of the PIV techniques to the investigation of particle motion in a gas–solid two-phase spiral flow in a horizontal tube. Axial velocities of the transported particles are obtained. Some important features of particle motion governing high transportation efficiency of the spiral flow are revealed by investigating probability density distribution of particle locations in a pipe cross-section.     

Results of direct numerical simulation of turbulent flow in a pipe of elliptical cross-section

Within the framework of the complete Navier-Stokes equations the turbulent flow in a pipe of elliptical cross-section with semiaxis ratio b/a = 0.5 is directly calculated for the Reynolds number Re = 6000 determined from the mean-flow velocity and the hydraulic diameter. The distribution of the average and pulsatory flow characteristics over the pipe cross-section are obtained. In particular, the secondary flow in the cross-section plane, typical of turbulent flows in noncircular pipes, is calculated. The equation for the longitudinal vorticity which determines the shape and intensity of the secondary flow is analyzed. In the balance equation for the pulsation kinetic energy the behavior of all the terms that characterize energy production, dissipation and redistribution over the pipe cross-section is described.     

Investigation of influence of coal properties on dense-phase pneumatic conveying at high pressure

Experiments of dense-phase pneumatic conveying of pulverized coal using nitrogen were carried out in a test facility at pressures of up to 3.7 MPa to study the effects of coal type, particle size and moisture content on flow characteristics. The Jenike shear test and scanning electron microscopy (SEM) were employed to provide a better understanding of effects of the material properties on flow characteristics. Two kinds of pulverized coals, Yanzhou and Datong, with similar particle size, moisture content and density, were used in the test. Pressure drop increases with increasing the particle size at similar solid–gas ratio, superficial velocity and pressure in the receiving hopper, and pressure drops through different test sections decrease firstly and then rise with increasing the conveying velocity for the same particle size, mass flow rate and pressure in the receiving hopper. The flowability of pulverized coal decreases with increasing the moisture content in the range from 3.24% to 8.18%. Unconfined yield strength (UYS) increases and flow function (FF) decreases with increasing the moisture content. Results of the shearing tests are consistent with the results of the conveying study. Pressure drops through different test sections are discussed and analyzed.     

Particle size distribution in CPFD modeling of gas–solid flows in a CFB riser

A computational particle fluid dynamics (CPFD) numerical method to model gas–solid flows in a circulating fluidized bed (CFB) riser was used to assess the effects of particle size distribution (PSD) on solids distribution and flow. We investigated a binary PSD and a polydisperse PSD case. Our simulations were compared with measured solids concentrations and velocity profiles from experiments, as well as with a published Eulerian-Eulerian simulation. Overall flow patterns were similar for both simulation cases, as confirmed by experimental measurements. However, our fine-mesh CPFD simulations failed to predict a dense bottom region in the riser, as seen in other numerical studies. Above this bottom region, distributions of particle volume fraction and particle vertical velocity were consistent with our experiments, and the simulated average particle diameter decreased as a power function with riser height. Interactions between particles and walls also were successfully modeled, with accurate predictions for the lateral profiles of particle vertical velocity. It was easy to implement PSD into the CPFD numerical model, and it required fewer computational resources compared with other models, especially when particles with a polydisperse PSD were present in the heterogeneous flow.     

Formation of particle jetting in a cylindrical shock tube

A dense, solid particle flow is numerically studied at a mesoscale level for a cylindrical shock tube problem. The shock tube consists of a central high pressure gas driver section and an annular solid powder bed with air in void regions as a driven section with its far end adjacent to ambient air. Simulations are conducted to explore the fundamental phenomena, causing clustering of particles and formation of coherent particle jet structures in such a dense solid flow. The influence of a range of parameters is investigated, including driver pressure, particle morphology, particle distribution and powder bed configuration. The results indicate that the physical mechanism responsible for this phenomenon is twofold: the driver gas jet flow induced by the shock wave as it passes through the initial gaps between the particles in the innermost layer of the powder bed, and the chaining of solid particles by inelastic collision. The particle jet forming time is determined as the time when the motion of the outermost particle layer of the powder bed is first detected. The maximum number of particle jets is bounded by the total number of particles in the innermost layer of the powder bed. The number of particle jets is mainly a function of the number of particles in the innermost layer and the mass ratio of the powder bed to the gas in the driver section, or the ratio of powder bed mass (in dimensionless form) to the pressure ratio between the driver and driven sections.     

固-液两相流黑水管道冲蚀磨损的数值模拟研究

煤气化黑水处理系统管道由于其流体介质高含固体颗粒和腐蚀性介质,且工作在高温、高压差环境中,极易受到冲蚀磨损和腐蚀的耦合作用而失效,影响其服役寿命. 采用计算流体力学(CFD)方法数值模拟研究了煤气化黑水处理系统固-液两相流管道的冲蚀磨损行为和机理,以及流体介质速度和固体颗粒粒径对管道冲蚀磨损的影响规律,并分析了盲通管和涡室结构对弯管冲蚀磨损行为的优化改善效果. 研究结果显示,煤气化黑水处理系统管线的冲蚀高危区主要分布在弯管外拱和变径管等结构突变区域;管道冲蚀磨损行为与其内部流体的运动和颗粒冲击特性有关;管道的冲蚀率均随着流体速度的增加而加剧,而粒径对弯管和变径管冲蚀率的影响并非单调关系,这与颗粒受力作用有关;弯管优化分析显示,涡室结构可以降低弯管的最大冲蚀率,减缓弯管的冲蚀磨损.      

Modeling the hydrodynamics of cocurrent gas–solid downers according to energy-minimization multi-scale theory

Cocurrent gas–solid downer reactors have many applications in industry because they possess the technological advantages of a lower pressure drop, shorter residence time, and less solid backmixing when compared with traditional circulating fluidized bed risers. By introducing the concept of particle clusters explicitly, a one-dimensional model with consideration of the interphase interactions between the fluid and particles at both microscale and mesoscale is formulated for concurrent downward gas–solid flow according to energy-minimization multi-scale (EMMS) theory. A unified stability condition is proposed for the differently developed sections of gas–solid flow according to the principle of the compromise in competition between dominant mechanisms. By optimizing the number density of particle clusters with respect to the stability condition, the formulated model can be numerically solved without introducing cluster-specific empirical correlations. The EMMS-based model predicts well the axial hydrodynamics of cocurrent gas–solid downers and is expected to have a wider range of applications than the existing cluster-based models.     

Multi-scale particle dynamics of low air velocity in a horizontal self-excited gas–solid two-phase pipe flow

The particle fluctuation velocities of a horizontal self-excited gas–solid two-phase pipe flow with soft fins near MPD (minimum pressure drop) air velocity are first measured by high-speed PIV in the acceleration and fully-developed regimes. Then orthogonal wavelet multi-resolution analysis and power spectrum are used to reveal multi-scale characteristics of particle fluctuation velocity. It is observed that the pronounced peaks of the spectra of axial and vertical fluctuation velocities appear in the range of low frequency near the bottom of pipe. These peaks of spectra become larger and their frequencies decrease by using fins. In the range of low frequencies (3–25 Hz), the wavelet components of the fluctuating energy of axial particle velocity make the main contribution accounting for 87% and 93% respectively for non-fin and using fins near the bottom of pipe. In the range of relatively high frequency (50–400 Hz), however, the wavelet components of using fins, accounting for about 49%, become smaller than that of non-fin, accounting for about 72%, in the suspension flow regime near the top of pipe. The skewness factor of axial particle fluctuation velocity indicates that the wavelet components follow the Gaussian probability distribution as the central frequency decreases.