Computational screening of electroactive indolequinone derivatives as high-performance active materials for aqueous redox flow batteries

The development of an organic-based aqueous redox flow battery (RFB) using quinone as an electroactive material has attracted great attention recently. This is because this battery is inexpensive, produces high energy density, and is environment friendly in stationary electrical energy storage applications. Herein, we investigate the redox potentials and solubilities of indole-5,6-quinone and indole-4,7-quinone derivatives in terms of the substituent effects of functional groups using theoretical calculations. Our results indicate that full-site substituted derivatives of indolequinone are more useful as active materials compared to single-site substituted derivatives. In particular, our calculations reveal that the substitution of –PO₃H₂ and –SO₃H functional groups with multiple polar bonds is very effective in increasing the activity of the aqueous RFB. As a strategy to overcome the limitation that the aqueous solubility is intrinsically low because they are organic molecules, we suggest the substitution of functional groups with multiple polar bonds to the backbones of active organic materials. Among 180 indolequinone derivatives, 17 candidates that meet the redox potential standards (≦ 0.2 V or ≧ 0.9 V) and eight candidates with solubility exceeding 2 mol/L are identified. Three indolequinone derivatives that satisfy both conditions are finally presented as promising electroactive candidates for an aqueous RFB.     

Computational screening of doping schemes for LiTi_2(PO_4)_3 as cathode coating materials

In all-solid-state lithium batteries,the impedance at the cathode/electrolyte interface shows close relationship with the cycle performance.Cathode coatings are helpful to reduce the impedance and increase the stability at the interface effectively.LiTi2(PO4)3(LTP),a fast ion conductor with high ionic conductivity approaching 10^-3S·cm^-1,is adopted as the coating materials in this study.The crystal and electronic structures,as well as the Li^+ion migration properties are evaluated for LTP and its doped derivatives based on density functional theory(DFT)and bond valence(BV)method.Substituting part of Ti sites with element Mn,Fe,or Mg in LTP can improve the electronic conductivity of LTP while does not decrease its high ionic conductivity.In this way,the coating materials with both high ionic conductivities and electronic conductivities can be prepared for all-solid-state lithium batteries to improve the ion and electron transport properties at the interface.     

钴掺杂MoSe2共生长中氢气的作用分析及磁电特性研究

采用原位共生长化学气相沉积法,以Co3O4、MoO3、Se粉末为前驱物,710℃下在SiO2衬底上生长掺钴MoSe2纳米薄片,分析讨论氢气含量对其生长及调节机理的影响.表面形貌分析表明,氢气的引入促进了成核所需的氧硒金属化合物以及横向生长中需要的CoMoSe化合物分子的生成;AFM(Atomic Force Microscope)结果表明氢气有利于生长单层二维超薄掺钴MoSe2.随着Co3O4前驱物用量的增加,样品的拉曼和PL(Photoluminescence)谱图分别表现出红移和蓝移现象,带隙实现从1.52—1.57 eV的调制.XPS(X-ray photoelectron spectroscopy)结果分析得到Co的元素组分比为4.4%.通过SQUID-VSM(Superconducting QUantum Interference Device)和器件电学测试分析了样品的磁电特性,结果表明Co掺入后MoSe2由抗磁性变为软磁性;背栅FETs器件的阈值电压比纯MoSe2向正向偏移5 V且关态电流更低;为超薄二维材料磁电特性研究及应用拓展提供了基础探索.     

Synergistic effect and mechanisms of ultrasound and AlOOH suspension on Al hydrolysis for hydrogen production

Ultrasound can accelerate and change the reaction process and is widely used in the field of hydrogen production and storage. In this study, ultrasound (US) and AlOOH suspension (AH) are used to promote hydrogen production from Al hydrolysis. The results indicate that both US and AH greatly shorten the induction time and enhance the hydrogen production rate and yield. The promoting effect of US and AH on Al hydrolysis originates from the acoustic cavitation effect and catalytic effect, respectively. When AH is used in combination with US, Al hydrolysis has the best hydrogen production performance and the hydrogen yield can reach 96.6 % within 1.2 h, because there is a synergistic effect on Al hydrolysis between AH and US. Mechanism analyses reveal that the micro-jets and local high temperature environment arising from acoustic cavitation improve the catalytic activity of AlOOH, while the suspended AlOOH particles enhance the cavitation effect of US. This work provides a novel and feasible method to promote hydrogen production from Al hydrolysis.     

Catalyst free rutile phase TiO2 nanorods as efficient hydrogen sensor with enhanced sensitivity and selectivity

Using a low-cost hydrothermal method, we demonstrated the fabrication of phase pure rutile phase high-density vertically aligned TiO₂ nanorods-based catalyst-free hydrogen (H₂) gas sensor. The synthesized TiO₂ nanorods on FTO are decorated with the aluminum interdigitated electrode pattern for electrical measurements. TiO₂ nanorods-based hydrogen sensor showed the optimum response of ∼53.18% at 150 ppm H₂ concentration relative to air at 100 °C. The measured response and recovery time of TiO₂ nanorods are 85 and 620 s, respectively. The TiO₂ nanorods-based H₂ gas sensor showed a relatively better response, good reproducibility, and stability at moderate temperatures, i.e., 50 and 100 °C. The electrochemical impedance measurements showed a small variation in the surface characteristics of TiO₂ nanorods before and after exposing H₂ gas. The carrier lifetime at 50 °C and 100 °C at 150 ppm are 5 μs and 3 μs, respectively. Interestingly, H₂ selectivity is also observed against H₂S, CO, and NH₃ gases, suggesting that high-density vertically aligned TiO₂ nanorods can be a good candidate for efficient hydrogen sensing at relatively low temperatures.     

Synthesis of Cr2O3/TNTs nanocomposite and its photocatalytic hydrogen generation under visible light irradiation

A novel Cr₂O₃/TNTs nanocomposite was prepared by loaded suitable amount of amorphous Cr₂O₃ on titanate nanotubes (TNTs) via hydrothermal reaction and impregnation process. XRD, SEM and TEM results demonstrated that the amorphous Cr₂O₃ nanoparticles were homogeneously dispersed on the surface of TNTs. The diffuse reflectance UV–visible absorption spectra exhibited that the spectral response of TNTs was extended to visible light region by coupled with Cr₂O₃. The 2.5Cr₂O₃/TNTs nanocomposite showed the highest activity of hydrogen generation by photocatalytic water-splitting under visible light irradiation (λ > 400 nm). The high activity of H₂ evolution for Cr₂O₃/TNTs nanocomposites was associated with the donor level in the forbidden band of TNTs semiconductor provided by dopant Cr³⁺ and a probably photocatalytic mechanism was proposed.     

TiO2及金属(Cu、Ni)掺杂催化材料水解制氢反应机理的理论研究

本文研究TiO₂以及金属(Cu、Ni)掺杂TiO₂催化剂水解制氢的两种不同析氢反应机理,计算了不同反应过程催化反应活化能,同时考察了系列催化剂电子激发态的催化活性.结果表明:催化剂电子激发态的催化活性增强,说明光照有助于降低反应的活化能,提高催化剂的活性.金属(Cu、Ni)掺杂TiO₂有助于降低水解制氢反应的活化能,且Cu的掺杂催化效果更明显,这与实验报道的结果一致.     

氢分子在Na2Al6团簇上的吸附和解离性能

氢的物理和化学吸附是氢存储的基本形式,而H₂分子的解离能垒是决定可逆储氢动力学性能的重要因素.纳米团簇是研究材料储氢性能的重要物质层次,研究氢与Na-Al团簇的相互作用性质能够了解纳米尺度的Na-Al氢化物的储氢性能.本文利用密度泛函理论,计算研究了H₂分子在较小的合金团簇Na₂Al₆上的吸附与解离性能.结果表明H₂分子在Na₂Al₆团簇上是弱的物理吸附,但很容易发生解离.氢分子的解离能垒很低,解离可以在环境温度下发生,纳米结构的Na₂Al₆团簇具有良好的化学储氢性能.     

Interaction of plasma facing materials for fusion devices with low energy hydrogen and helium particles

Abstract

Radiation damage formed in metal specimens exposed to long pulse tokamak plasmas of TRIAM-1M was examined by transmission electron microscopy. By comparing these results with those of low energy hydrogen ion irradiation it was concluded that the charge exchange energetic neutrals of hydrogen emitted from the core plasma caused remarkable displacement damage. The flux of the neutrals in the energy range of 0.5–3 keV which were responsible for displacement damage, was estimated to be about 1.5–3 × 10¹⁸ H/m²/s. These energetic neutrals cause not only material degradation at the sub-surface region but also change bulk properties of plasma facing components in a plasma confinement device. Effect of helium plasma was also discussed with emphasis on very strong effects on damage accumulation. Damage by He is a serious issue of plasma facing materials.     

Computational study of pyrazine‐based derivatives and their N‐oxides as high energy materials

Gas‐phase heats of formation (HOF), solid‐phase HOF, detonation properties, electronic structure and thermal stability for a series of polynitro pyrazine derivatives containing three heterocycles have been investigated using density functional theory. It is found that the nitro group is an efficient tool to improve HOF of pyrazine derivatives. Furthermore, detonation velocities and detonation pressures of these compounds are evaluated using empirical Kamlet–Jacobs equations. As a result, it indicates that the nitro group is useful to enhance detonation properties. Detonation velocities of five compounds are 9.67, 9.20, 9.74, 9.76 and 9.87 km/s, respectively, which are significantly larger than that of HMX (9.10 km/s). Bond dissociation energy is also performed to investigate their thermal stability, showing that thermal stability of these compounds is little affected by nitro groups or the position of substituent groups. Considering solid‐phase HOF, detonation properties and thermal stability, some of pyrazine derivatives can be potential high energy density materials. Copyright © 2013 John Wiley & Sons, Ltd.     

Computational design and screening of promising energetic materials: Novel azobis(tetrazoles) with ten catenated nitrogen atoms chain

Density functional theory methods were used to study on 2 N10 compounds, 1,1′‐azobis(tetrazole) and 1,1′‐azobis(5‐methyltetrazole). We systematically investigated 10 novel substituted azobis(tetrazoles) with 10 catenated nitrogen atoms and various energetic groups (–CF₃ 1 , –C(NO₂)₃ 3 , –N₃ 5 , –NH₂ 6 , –NHNH₂ 7 , –NHNO₂ 8 , –NO₂ 9 , –OCH₃ 10 , –OH 11 , –ONO₂ 12 ). The optimized geometry, frontier molecular orbitals, electrostatic potential, Infrared and nuclear magnetic resonance spectrum were calculated for inspecting the molecular structure and stability as well as chemical reactivity. The effects of different substituents on the density, enthalpy of formation, heat of explosion, detonation velocity and pressure, and sensitivity of the azobis(tetrazole) derivatives have been investigated. Compound 9 with nitro was found to have remarkable detonation performances (D = 9.61 km/s, P = 42.14 GPa), which are close to the excellent explosive CL‐20. Results show that compounds 1 , 3 , 4 , 7 , 9 , 11, and 12 have high potential to replace RDX. It is surprising that compounds 1 , 3 , 9, and 12 possess better energetic properties than HMX. These novel substituted azobis(tetrazoles) with unique N10 structure may be promising candidates of HEDMs with outstanding performance and acceptable sensitivities.     

Reconnaissance of the specific surface of vapour grown carbon micro and nanofibres as a main controller of the sorption of hydrogen

The influence of the hydrogen content in several physical aspects of carbonaceous microfibres obtained from a mixture of hydrogen and hydrocarbon gas is examinated in this study. The hydrogen content is evaluated behalf a measurement of the fibres density. These changes of content depend on the manufacturing process and further treatments of the fibres. The surface energy is established after contact angle evaluation. There is not a clear relation between the surface energy and the porosity, which is a very relevant parameter in order to establish the hydrogen storage capacity of all materials.The fibres have been evaluated using Kelvin probe force microscopy (KPFM), which provides a map of the surface potential. These measurements suggest a relation between the surface potential and the hydrogen adsorbed in the surface of the fibres.     

Synthesis and characterization of TiO2-coated magnetite clusters (nFe3O4@TiO2) as anode materials for Li-ion batteries

TiO₂-coated magnetite clusters (nFe₃O₄@TiO₂) were facilely prepared through the sol–gel reaction between Ti alkoxides (TEOT) and magnetite clusters (nFe₃O₄) with terminated alkoxy groups. The composite particles represented a core–shell nanostructure (nFe₃O₄@TiO₂) consisting of a Fe₃O₄ cluster core and a TiO₂ capsule layer. The capsule layer of nFe₃O₄@TiO₂ was increased with increasing amounts of TEOT (150, 300, 500 μl) in sol–gel reaction. The Fe₃O₄@TiO₂ (150 μl of TEOT) with a thin TiO₂ layer (ca. 10 nm) exhibited two kinds of cathodic (0.79 V and 1.61 V) and anodic (1.78 and 2.1 V) peaks attributed to the reduction and oxidation process by Fe₃O₄ core and TiO₂ layer, respectively. The thin nFe₃O₄@TiO₂ (150 μl of TEOT) exhibited the enhanced capacity retention by ca. 40% probably due to the buffering effect of TiO₂ capsule layer. However, the thick nFe₃O₄@TiO₂ (300–500 μl of TEOT) exhibited a rapid capacity fading due to the disintegrated core–shell nanostructure, i.e., unfavorable hetero-junction between TiO₂ matrix and magnetite clusters.     

Silane-modified polymers as interphases in glass-fibre-reinforced composites: 2. Grafting and crosslinking of interphase materials

_—This paper presents an interphase engineering technique suitable for grafting silane-modified polymers onto glass fibres to be used in composites with enhanced impact tolerance. The silane-modified polymers include ethylene polymers grafted with γ-methacryloxypropyltrimethoxysilane (MPS) and a copolymer of butyl acrylate (BuA) and MPS. The grafting of functionalized interphase materials onto glass fibres is performed in solution. By changing the concentrations of the solutions, different amounts of polymer can be deposited on the fibres. Water crosslinking of the polymer gives the possibility of producing stabilised interfacial polymer coatings over a range of thicknesses. It is concluded that acidic conditions (1) promote the grafting of silane-modified polymers on glass fibres and (2) for a given reaction time, increase the amount of crosslinked polymer in the interphase, i.e. yield more stable interphases. It is also likely that preserving acidic conditions at the fibre/polymer interface is important for maintaining bonding across the interface. It is shown that polystyrene/glass-fibre composites having SEBS at the interface are promising candidates for high-impact-tolerance composites.     

IR investigation of the interaction of deuterium with Ce0.6Zr0.4O2 and Cl-doped Ce0.6Zr0.4O2

The interaction of deuterium with Ce_0.6Zr_0.4O₂, synthesised by a co-precipitation technique, is discussed on the basis of the sample's bulk and surface composition and the presence of trace amounts of silicon. Redox cycling resulted in surface cerium enrichment, which, however, only moderately affected the interaction of the material with D₂. Addition of a trace amount of chloride ion to the oxide surface promoted both H/D scrambling and vacancy creation. Chloride ion was also found to prevent the surface cerium enrichment induced by redox cycling.     

用对应原理导出氢原子量子化能量、量子化电子轨道以及Bohr稳定轨道量子化条件

用对应原理导出了氢原子量子化能量、量子化电子轨道以及Bohr稳定轨道量子化条件(角动量量子化条件)     

Synthesis and characterization of lithium manganese oxides with core-shell Li4Mn5O12@Li2MnO3 structure as lithium battery electrode materials

By a facile LiNO₃ flux method, lithium manganese oxide composites (xLi₄Mn₅O₁₂? yLi₂MnO₃) were synthesized using a hierarchical organization precursor of manganese dioxide. Li₄Mn₅O₁₂ and Li₂MnO₃ have spinel and rocksalt structures, respectively. The lithiation and structural transformation from the precursor to the composites occurred topotactically from exterior toward interior in the precursor particle with the increase of reaction time, and the composites had core-shell spinel@rocksalt structures in addition to the original hierarchical core-shell organization. The electrochemical measurements at 50 °C after 50 cycles confirmed that a typical spinel@rocksalt cathode had higher capacity retention (87.1%) than that with the composition close to the stoichiometric spinel (64.6%), indicating the Li₂MnO₃ shell can improve cycling stability for the composite electrode at elevated temperature.     

Effects of packing materials on the sensitivity of RadFET with HfO2 gate dielectric for electron and photon sources

The radiation sensing field effect transistor (RadFET) with SiO₂ gate oxide has been commonly used as a device component or dosimetry system in the radiation applications such as space research, radiotherapy, and high-energy physics experiments. However, alternative gate oxides and more suitable packaging materials are still demanded for these dosimeters. HfO₂ is one of the most attractive gate oxide materials that are currently under investigation by many researchers. In this study, Monte Carlo simulations of the average deposited energy in RadFET dosimetry systems with different package lid materials for point electron and photon sources were performed with the aim of evaluating the effects of package lids on the sensitivity of the RadFET by using HfO₂ as a gate dielectric material. The RadFET geometry was defined in a PENGEOM package and electron–photon transport was simulated by a PENELOPE code. The relatively higher average deposited energies in the sensitive region (HfO₂ layer) for electron energies of 250?keV–20?MeV were obtained from the RadFET with the Al₂O₃ package lid despite of some deviations from the general tendency. For the photon energies of 20–100?keV, the average amount of energy deposited in RadFET with Al₂O₃ package was higher compared with the other capped devices. The average deposited energy in the sensitive region was quite close to each other at 200?keV for both capped and uncapped devices. The difference in the average deposited energy of the RadFET with different package lid materials was not high for photon energies of 200–1200?keV. The increase in the average deposited energy in the HfO₂ layer of the RadFET with Ta package lid was higher compared with the other device configurations above 3?MeV.     

Computational studies of the effects of ortho‐ring and para‐ring activation on the kinetics of SNAr reactions of 1‐chloro‐2‐nitrobenzene and 1‐phenoxy‐2‐nitrobenzene with aniline

Computational studies are reported for reactions of 4‐substituted‐1‐chloro‐2,6‐dinitrobenzenes 1 , 6‐substituted‐1‐chloro‐2,4‐dinitrobenzenes 2 and some of the corresponding 1‐phenoxy derivatives 3 and 4 with aniline in the gas phase. The effects of substituent groups in the calculated energy values for reactants 1–4 , transition states structures, intermediates and products formed in the reactions between the compounds and anilines have been compared. Calculated bonds length and angles from optimized structures of the reactants were comparable with values reported for some of compounds 1–4 obtained by X‐ray crystal structures analysis. Generally, the decomposition of the Meisenheimer intermediate to the products requires more energy compared with the reactants except for when R = H. The order of stabilization of the intermediate was found to reflect the relative order of activation by substituents in the substrates. The 4‐substituted‐1‐chloro‐2,6‐dinitrobenzenes 1 and the phenoxy derivatives 3 were found to be more stable than their corresponding 6‐substituted analogues. This is an indication that the rate of nucleophilic attack at 1‐position will increase with increasing ring activation but may be reduced by steric repulsion at the reaction centre that increases in the order Cl < OPh. However, the steric hindrance to the steps involved in nucleophilic substitution by aniline is significantly increased when the substrates contain two ortho‐substituents. In most cases, the rate determining step is the decomposition of the σ‐adduct intermediate except with 1‐chloro‐2,6‐dinitrobenzenes 1 and 6‐substituted‐1‐chloro‐2,4‐dinitrobenzenes 2 , either because of reduction in ring activation or the presence of bulky ortho‐substituents in the chloro compounds 1 and 2 . Copyright © 2014 John Wiley & Sons, Ltd.