Pentacene as a hole transport material for high performance planar perovskite solar cells

A cost-effective and efficient organic semiconductor pentacene was developed as a hole transport layer (HTL) material to replace classical PEDOT:PSS for planar perovskite solar cells (PSCs). As expected, the pentacene based device exhibits power conversion efficiency (PCE) of 15.90% (J_sc of 19.44 mA/cm², V_oc of 1.07 V, and FF of 77%), comparable to the PEDOT:PSS based device (PCE of 15.65%, J_sc of 18.78 mA/cm², V_oc of 1.07 V, and FF of 77%) under the same experimental conditions. The excellent performance of vacuum deposited pentacene is mainly attributed to the high efficient charge extraction and transfer in device due to the high-quality perovskite film grown on the top of pentacene substrate and a favorable energy-level alignment together with a desired downward band bending formed at the perovskite/pentacene interface. Our research has confirmed that pentacene could be served as a promising HTL material to achieve effective and potentially economical planar type PSCs.     

A facile and low-cost fabrication of TiO2 compact layer for efficient perovskite solar cells

A uniform and compact hole blocking layer is necessary for high efficient perovskite-based thin film solar cell. In this study, we fabricated TiO₂ compact layers by using a simple dip-coating method in contrast to the widely used techniques such as spin coating and spray pyrolysis. In this study, we optimized the surface morphologies of dip-coating based TiO₂ compact layers by controlling the concentration of Ti precursor solution diluted in ethanol. The analyses of devices performance characteristics showed that thickness and surface morphologies of different TiO₂ compact layers played a critical role in affecting the efficiencies. The dip-coating route to prepare TiO₂ compact layers employed in this study is more amenable to fabricate the large area device and less expensive.     

Surface modulation of halide perovskite films for efficient and stable solar cells

As the main distribution place of deep-level defects and the entrance of water, the interface is critical to determining both the power conversion efficiency (PCE) and the stability of perovskite solar cells (PSCs). Suitable interface design can dramatically passivate interface defects and optimize energy level alignment for suppressing the nonradiative recombination and effectively extracting the photogenerated carriers towards higher PCE. Meanwhile, a proper interface design can also block the interface diffusion of ions for high operational stability. Therefore, interface modification is of great significance to make the PSCs more efficient and stable. Upon optimized material choices, the three-dimensional halide perovskite graded junction layer, low-dimensional halide perovskite interface layer and organic salt passivation layer have been constructed on perovskite films for superior PSCs, yet a systematic review of them is missing. Thus, a guide and summary of recent advances in modulating the perovskite films interface is necessary for the further development of more efficient interface modification.     

Charge transfer modification of inverted planar perovskite solar cells by NiOx/Sr:NiOx bilayer hole transport layer

Perovskite solar cells (PSCs) are the most promising commercial photoelectric conversion technology in the future. The planar p-i-n structure cells have advantages in negligible hysteresis, low temperature preparation and excellent stability. However, for inverted planar PSCs, the non-radiative recombination at the interface is an important reason that impedes the charge transfer and improvement of power conversion efficiency. Having a homogeneous, compact, and energy-level-matched charge transport layer is the key to reducing non-radiative recombination. In our study, NiO$_{x}$/Sr:NiO$_{x}$ bilayer hole transport layer (HTL) improves the holes transmission of NiO$_{x}$ based HTL, reduces the recombination in the interface between perovskite and HTL layer and improves the device performance. The bilayer HTL enhances the hole transfer by forming a driving force of an electric field and further improves $J_{\rm sc}$. As a result, the device has a power conversion efficiency of 18.44%, a short circuit current density of 22.81 mA$\cdot$cm$^{-2}$ and a fill factor of 0.80. Compared to the pristine PSCs, there are certain improvements of optical parameters. This method provides a new idea for the future design of novel hole transport layers and the development of high-performance solar cells.     

Recent advances of interface engineering in inverted perovskite solar cells

Perovskite solar cells (PSCs) have witnessed great achievement in the past decade. Most of previous researches focus on the n—i—p structure of PSCs with ultra-high efficiency. While the n—i—p devices usually used the unstable charge transport layers, such as the hygroscopic doped spiro-OMeTAD, which affect the long-term stability. The inverted device with the p—i—n structure owns better stability when using stable undoped organic molecular or metal oxide materials. There are significant progresses in inverted PSCs, most of them related to charge transport or interface engineering. In this review, we will mainly summarize the inverted PSCs progresses related to the interface engineering. After that, we prospect the future direction on inverted PSCs.     

Impact of work function of back contact of perovskite solar cells without hole transport material analyzed by device simulation

The impact of the work function of a metal back contact on lead methylammonium tri-iodide based perovskite solar cells without hole transport material (HTM) was analyzed using device simulation. The elimination of the HTM is attractive in terms of the simplification of device structure and fabrication process. In the solar cell, a back junction is formed by the perovskite absorber and metal back contact. The device simulation revealed that the elimination of the HTM did not change the built-in voltage (V_bi) of the device when the work function of the metal back contact (?_M) was similar to the valence band maximum of the absorber (E_{v_absorber}). In the HTM-free structure, V_bi showed a high value if ?_M was equal to or deeper than E_{v_absorber}. In contrast, when ?_M was shallower than E_{v_absorber}, V_bi monotonically decreased, resulting in the decrease in open-circuit voltage of the device. The results showed the importance of the ?_M matching to maintain V_bi, which is useful guideline for the design of the HTM-free perovskite solar cells.     

Improving the performance of perovskite solar cells with glycerol-doped PEDOT:PSS buffer layer

In this paper, we investigate the effects of glycerol doping on transmittance, conductivity and surface morphology of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate))(PEDOT:PSS) and its influence on the performance of perovskite solar cells.. The conductivity of PEDOT:PSS is improved obviously by doping glycerol. The maximum of the conductivity is 0.89 S/cm when the doping concentration reaches 6 wt%, which increases about 127 times compared with undoped. The perovskite solar cells are fabricated with a configuration of indium tin oxide(ITO)/PEDOT:PSS/CH_3NH_3PbI_3/PC_(61)BM/Al, where PEDOT:PSS and PC_(61)BM are used as hole and electron transport layers, respectively. The results show an improvement of hole charge transport as well as an increase of short-circuit current density and a reduction of series resistance, owing to the higher conductivity of the doped PEDOT:PSS. Consequently, it improves the whole performance of perovskite solar cell. The power conversion efficiency(PCE) of the device is improved from 8.57% to 11.03% under AM 1.5 G(100 mW/cm~2 illumination) after the buffer layer has been modified.     

双电子传输层结构硫硒化锑太阳电池的界面特性优化

硫硒化锑薄膜太阳电池因其制备方法简单、原材料丰富无毒、光电性质稳定等优点,成为了光伏领域的研究热点.经过近几年的发展,硫硒化锑太阳电池的光电转换效率已经突破10%,极具发展潜力.本文针对硫硒化锑太阳电池中n/i界面引起的载流子复合进行了深入研究.发现硫硒化锑太阳电池的界面特性会受到界面电子迁移能力和能带结构两方面的影响.界面电子迁移率的提高能使电子更有效地传输至电子传输层,实现器件短路电流密度和填充因子的有效提升.在此基础上,引入ZnO/Zn_1-xMg_xO双电子传输层结构能够进一步优化硫硒化锑太阳电池性能.其中,Zn_1-xMg_xO能级位置的改变可以同时调节界面和吸光层的能级分布,在Zn_1-xMg_xO导带能级为-4.2 eV,对应Mg含量为20%时,抑制载流子复合的效果最为明显,硫硒化锑太阳电池也获得了最佳的器件性能.在去除缺陷态的理想情况下,双电子传输层结构硫硒化锑太阳电池在600 nm厚时获得了20.77%的理论光电转换效率,该研究结果为硫硒化锑太阳电池...     

Inverted organic solar cells with solvothermal synthesized vanadium-doped TiO_2 thin films as efficient electron transport layer

We investigated the effects of using different thicknesses of pure and vanadium-doped thin films of TiO_2 as the electron transport layer in the inverted configuration of organic photovoltaic cells based on poly(3-hexylthiophene) P3HT:[6-6] phenyl-(6) butyric acid methyl ester(PCBM). 1% vanadium-doped TiO_2nanoparticles were synthesized via the solvothermal method. Crystalline structure, morphology, and optical properties of pure and vanadium-doped TiO_2 thin films were studied by different techniques such as x-ray diffraction, scanning electron microscopy, transmittance electron microscopy, and UV–visible transmission spectrum. The doctor blade method which is compatible with roll-2-roll printing was used for deposition of pure and vanadium-doped TiO_2 thin films with thicknesses of 30 nm and 60 nm. The final results revealed that the best thickness of TiO_2 thin films for our fabricated cells was 30 nm. The cell with vanadium-doped TiO_2 thin film showed slightly higher power conversion efficiency and great J_(sc) of 10.7 mA/cm~2 compared with its pure counterpart. In the cells using 60 nm pure and vanadium-doped TiO_2 layers, the cell using the doped layer showed much higher efficiency. It is remarkable that the external quantum efficiency of vanadium-doped TiO_2 thin film was better in all wavelengths.     

Effect of an Al-doped ZnO electron transport layer on the efficiency of inverted bulk heterojunction solar cells

Doping is a widely-implemented strategy for enhancing the inherent electrical properties of metal oxide charge transport layers in photovoltaic devices because higher conductivity of electron transport layer (ETL) can increment the photocurrent by reducing the series resistance. To improve the conductivity of ETL, in this study we doped the ZnO layer with aluminum (Al), then investigated the influence of AZO on the performance of inverted bulk heterojunction (BHJ) polymer solar cells based on poly [[4,8-bis [(2-ethylhexyl)oxy]benzo [1,2-b:4,5-b’]dithiophene-2,6-diyl]-[3-fluoro-2[(2-ethylhexyl)-carbonyl]-thieno-[3,4-b]thiophenediyl ]] (PTB7):[6,6]-phenyl C71 butyric acid methyl ester (PC₇₁BM). The measured conductivity of AZO was ~10⁻³ S/cm, which was two orders of magnitude higher than that of intrinsic ZnO (~10⁻⁵ S/cm). By decreasing the series resistance (R_s) in a device with an AZO layer, the short circuit current (J_sc) increased significantly from 15.663 mA/cm² to 17.040 mA/cm². As a result, the device with AZO exhibited an enhanced power conversion efficiency (PCE) of 8.984%.     

Thickness effect of the TiO2 nanofiber scattering layer on the performance of the TiO2 nanoparticle/TiO2 nanofiber-structured dye-sensitized solar cells

TiO₂ nanofibers (NFs) were fabricated by an electrospinning process and were used as scattering layers in dye-sensitized solar cells (DSSCs). The NF-coated photoanodes of the DSSCs were prepared with a variety of scattering layer thicknesses. The thickness effect of the scattering layer on the double-layered TiO₂ nanoparticle (NP)/TiO₂ NF structure was investigated through structural, morphological, and optical measurements. In the double-layered photoanode, the TiO₂ NP layer plays a major role in dye adsorption and light transmission, and the TiO₂ NF scattering layer improves the absorption of visible light due to the light scattering effects. The scattering effect of TiO₂ NFs layer was examined by the incident monochromatic photon-to-electron conversion efficiency (IPCE) and UV–Vis spectrometry. The conversion efficiency for the 12 μm-thick photoanode composed of a 2 μm-thick TiO₂ NF layer and 10 μm-thick TiO₂ NP layer was higher than that of DSSCs with only TiO₂ NPs photoanode by approximately 33%.     

The effect of TiCl4-treated TiO2 compact layer on the performance of dye-sensitized solar cell

In order to prevent the charge recombination at the interface between the transparent-conducting oxide (TCO) substrate and electrolyte, a TiO₂ compact layer was deposited on the substrate by hydrolysis of TiCl₄ aqueous solution. Optimum thickness of the compact layer was found to be ∼25 nm, which showed ∼24% increase in the power-conversion efficiency compared with the bare cell. Impedance spectra indicated that the interfacial charge-transfer resistance of TCO/electrolyte interface was increased by more than a factor of three with the TiO₂ compact layer at 0.4 V. Moreover, the electron-carrier lifetime of the 25 nm-deposited cell was improved by a factor of five compared with the bare cell.     

p种子层对单室制备微晶硅电池性能的影响

采用单室等离子体化学气相沉积技术沉积pin微晶硅电池时,硼污染降低了本征材料的晶化率并影响了p/i界面特性.针对该问题文中采用p种子层技术,即在沉积p层后采取高的H₂/SiH₄比率及适当的功率又沉积一个薄的p层,初步研究了p种子层对微晶硅i层纵向均匀性及电池性能的影响.实验结果表明：采用此方法能改善p/i界面特性,提高本征材料纵向结构的均匀性并降低硼对本征层的污染,有效地提高单结微晶硅电池的性能.最后,通过优化沉积条件,制备得到光电转换效率为881%（1 cm 关键词： 单室 甚高频等离子体增强化学气相沉积 微晶硅太阳电池 p种子层     

4,4′,4″-三(N-3-甲基苯基-N-苯基氨基)三苯胺掺杂MoOx作为空穴传输层对有机太阳电池性能的影响

通过采用4,4′,4″-三(N-3-甲基苯基-N-苯基氨基)三苯胺 (m-MTDATA)掺入MoO_x作为器件的空穴传输层来提高酞菁铜(CuPc)/C₆₀小分子 有机太阳电池的效率. 采用真空蒸镀的方法制备了一系列器件, 其中结构为铟锡氧化物 (ITO)/m-MTDATA:MoO_x(3:1)(30 nm)/CuPc(20 nm)/C₆₀(40 nm)/4,7-二苯 基-1,10-菲罗啉 (Bphen)(8 nm)/LiF(0.8 nm)/Al(100 nm)的器件, 在AM1.5 (100 mW/cm²)模拟太阳光的照射条件下, 开路电压V_oc=0.40 V, 短路电流J_sc=6.59 mA/cm², 填充因子为0.55, 光电转换效率达1.46%, 比没有空穴传输层的器件ITO/CuPc(20 nm)/C₆₀(40 nm)/Bphen(8 nm)/LiF(0.8 nm)/Al(100 nm) 光电转换效率提高了38%. 研究表明, 加入m-MTDATA:MoO_x(3:1)(30 nm)空穴传输层减小了有机层和ITO电极之间的接触电阻, 从而减小了整个器件的串联电阻, 提高了器件的光电转换效率.     

阴极功函数和激子产生率对肖特基接触单层有机太阳能电池开路电压的影响研究

运用数值方法系统研究了阴极功函数,激子产生率和温度对肖特基接触单层有机太阳能电池开路电压的影响,分析了开路电压条件下有机太阳能电池有机层内载流子和电场的分布.结果表明在阳极功函数一定时开路电压随着阴极功函数（W_c）的降低而增大,当W_c接近有机材料的最低未被占据分子轨道（LUMO）能级时开路电压不再增大而达到一个饱和值,饱和开路电压随激子产生率的提高而增大;对于给定的阳极和阴极功函数,开路电压随激子产生率的提高而增大并在激子产生率达到一 关键词： 开路电压 温度 阴极功函数 单层有机太阳能电池     

利用不同阴极缓冲层来改善Pentacene/C60太阳能电池的性能

制备了结构为ITO/Pentacene/C₆₀/Al的双层光伏电池器件,在C₆₀/Al界面插入了常用的缓冲层材料bathocuproine(BCP)作为阴极缓冲层,通过优化BCP层的厚度来提高电池的性能并研究了阴极缓冲层的作用机理.实验发现,BCP厚度为10 nm时器件的效率最高,为0.46%.在此基础上,利用bathophenanthroline(Bphen)和3,4,9,10-Perylenetetracarb-oxylicdianhydride(PTCDA 关键词： 有机太阳能电池 Pentacene 60')" href="#">C₆₀ 缓冲层