应用高效液相色谱-二极管阵列检测器-蒸发光散射检测器联用技术同时测定清开灵注射液中的五类有效成分

建立了复方清开灵注射液中5类主要有效成分的定量测定方法。应用高效液相色谱-二极管阵列检测器-蒸发光散射检测器联用技术(HPLC-DAD-ELSD),根据各类成分紫外吸收光谱的差异,分别在240,254,280和330 nm波长下检测栀子苷、核苷(包括尿苷和腺苷)、黄芩苷和有机酸(包括绿原酸和咖啡酸)等4类成分,同时使用ELSD测定胆酸、熊去氧胆酸和猪去氧胆酸等3种甾体化合物,从而实现了清开灵注射液中5类有效成分(共9个化合物)的同时分离和定量测定。用该法测定了3个不同厂家的19批清开灵注射液成品。该法快速、准确,操作相对简单,为中药复方复杂体系的多组分定量测定和质量控制提供了一种可靠、合理且简便、易行的方法模式。     

Critical appraisal of the flame photometric detector in petroleum analysis

Summary This paper summarises experience gained at the British Petroleum Limited Research Centre, Sunbury-on-Thames, with sulphur selective gas chromatography (GC) detectors. A single flame photometric detector (SFPD) has been in use for three years for research and routine applications. Three areas of interest are described demonstrating in turn different characteristics of the detector. Firstly, a determination of trace levels of individual organo-sulphur compounds in the 15–65°C cut of crude oils illustrates the complexity of using an SFPD in a rigorously quantitative manner. Secondly, the use of an SFPD as a qualitative tool for the comparison of the sulphur distribution of crude oils up to the temperature limit of GC is cited. Finally, a third section describes the properties of a dual flame photometric detector (DFPD) which are compared and contrasted with those of the SFPD.     

Investigating the performance characteristics of the barrier discharge ionization detector and comparison to the flame ionization detector for the gas chromatographic analysis of volatile and semivolatile organic compounds

Abstract

The response behavior and performance characteristics of the recently introduced barrier discharge ionization detector (BID) for gas chromatography (GC-BID) were investigated by analyzing different classes of organic compounds such as alcohols, alkanes, cycloaliphatic compounds, polycyclic aromatic hydrocarbons (PAHs), and others. The results obtained by GC-BID were compared with those of gas chromatography with flame ionization detection (GC-FID), aiming to demonstrate the particular merits of the new BID detector over the well-established FID. The response of the BID not only was found to be strongly dependent on the detector settings, but also shows a high dependence on the analyte class and the individual analyte. The sensitivity of the BID detector compared to the FID was higher by a factor of ca. 4 on average when considering all compounds analyzed. The relative standard deviation (RSD) was better than 5% for the majority of the cases. The BID detector showed better precision (lower RSD) in comparison with the FID for the investigated compounds. Linear calibrations were obtained for the analytes over more than four orders of magnitude with coefficients of determination typically higher than 0.999 and the limits of detection varied from 0.04 to 1.48?ng/s for the GC-BID.     

Gas chromatographic determination of organolead compounds with an alternating current plasma detector

The performance of the gas chromatography/alternating current plasma detector as a selective detector for organolead compounds is investigated. The helium make-up flow rate and the spatial position from which the lead emission is viewed, have an effect on the detector response. The detection limit for tetrabutyl lead was established as 130 pg/s and the lead selectivity ratio was found to exceed 13,800. Some applications of organolead determination in complex matrices were also studied in order to demonstrate the selectivity and sensitivity of the alternating current plasma detector.     

Universal and discriminative detection using a miniaturized pulsed discharge detector in comprehensive two-dimensional GC

A miniaturized pulsed discharge detector (Mini-PDD) has been successfully demonstrated for comprehensive 2-D GC (GC x GC) analysis of pyrolysis gasoline and the pyrolysis GC x GC analysis of a polyethylene copolymer. The detector cell volume of the Mini-PDD is reduced to 25% of the Valco plug-in PDD D-3. An n-C11 peak width at base is 96 ms for the Mini-PDD, about 23% larger than a peak width of 78 ms detected by a flame ionization detector (FID). The Mini-PDD has sufficient response time for most GC x GC applications. When Mini-PDD is operated in helium photoionization mode (Mini He-PDD), it is a universal detector for both inorganic and organic compounds. This is especially useful when detection of water is needed in GC x GC applications. When krypton is doped in the helium discharge gas (Mini Kr-PDD), it can suppress signals of compounds having higher ionization potentials and enhance relative signal intensities of aromatic compounds. The determination of aliphatic to aromatic hydrocarbon ratios is essential to the operation of petroleum crackers. Comparison of the signal from two modes of the Mini-PDD is a simple and fast way to verify the location of aromatics in comprehensive 2-D gas chromatograms.     

高效液相色谱圆二色检测技术在手性化合物分析中的应用

对近年来高效液相色谱圆二色检测技术在手性化合物分析中的应用进展进行综述,简单介绍了高效液相色谱圆二色检测器的原理和特点,着重介绍了非手性色谱条件下圆二色检测技术在手性化合物对映体纯度测定、复杂基质中手性化合物分析以及在手性化合物绝对构型测定中的应用,并讨论了它的应用前景。     

Quantitative gas chromatographic analysis of perhalogenated compounds using a flame lonization detector

Summary In the determination of several perhalogenated compounds after gas chromatographic separation on an Apiezon L column, using a flame ionization detector, all the compounds tested gave linear area-mass plots although the coefficients observed do not lead to extrapolations which would permit quantitation of perhalogenated compounds for which no standard is available. Of the compounds tested, dibromodichloromethane, tetrachloroethene and tetrabromoethene gave good linear correlations of area ratio-mass ratio (using n-decane as the internal standard). Bromotrichloromethane and tetrabromomethane gave continuously curving area ratio-mass ratio plots which were very reproducible and could be used for graphical interpolation.     

Determination of butyl- and phenyltin compounds in human urine by HS-SPME after derivatization with tetraethylborate and subsequent determination by capillary GC with microwave-induced plasma atomic emission and mass spectrometric detection

A headspace solid-phase micro-extraction (HS-SPME) method was developed and optimized for gas chromatographic separation and determination of commonly found organotin compounds in human urine after potential exposure. Butyl- and phenyltin compounds were in situ derivatized to ethylated derivatives by sodium tetraethylborate (NaBEt₄) directly in the urine matrix. The relevant parameters affecting the yield of the SPME procedure were examined using tetrabutyltin as internal standard. The method was optimized for direct use in the analysis of undiluted human urine samples and mono-, di- and tri-substituted butyl- and phenyltin compounds could be determined after a 15-min headspace extraction time at room temperature. The selectivity of the microwave-induced plasma atomic emission detector (MIP-AED) as an element specific detector in combination with the relatively selective sample preparation technique of HS-SPME allowed the interference-free detection of the organotin compounds in all cases. A quadrupole mass spectrometer was used in parallel experiments as a detector for the confirmation of the identity molecular structure of the eluted compounds. The performance characteristics of the developed method are given for the determination of mixtures of these compounds. Finally the proposed method was applied to the analysis of several human urine samples.     

微柱高效液相色谱与火焰光度检测器联用研究

报道了微柱高效液相色谱（micro-column HPLC）与火焰光度检测器（FPD）在线联用系统的研究,目的是发展一种不经复杂前处理步骤即可直接测定有机锡化合物的方法。三丁基锡氯化物（TBT）等经HPLC微柱分离后,通过毛细管连接引入特制的燃烧头,通过火焰光度检测器进行检测,对系统有关参数进行了优化和讨论。所建方法可以直接测定各种水样中的三丁基锡氯化物。     

Operating the pulsed discharged detector in both the electron-capture and photoionization modes within the same GC analysis

Summary Since the electron-capture detector (ECD) is highly selective, it is imperative to use a more universal ionization detector in conjunction with the ECD in order to detect non-capturing or weakly capturing compounds. Also in an EC study of weakly or moderately strong electron-capturing compounds, it is necessary to identify the EC peak of the compound by identifying the major component with an ionization detector. In this paper we have shown that the pulsed discharge detector can be interchanged between the EC and the helium ionization modes within 4–6 s. The application of this procedure has been illustrated with a mixture of alkane/alkene chlorocompounds. The interchange between EC and argon photoionization modes has also been investigated. The change from EC to argon photoionization also occurs in 4–6 s but the reverse process requires 9 s.     

气相色谱法测定天然气中的硫化物

用气相色谱法,选择脉冲火焰光度检测器（PFPD）,在甲基硅油毛细管色谱柱上分析天然气中的硫化物。该方法灵敏度高,选择性好,结果准确,相对标准偏差小于1.1%。     

Determination of Toxic Organophosphorus Compounds by Specific and Nonspecific Detectors

Abstract

Sample preparation procedures and gas chromatography methodology are presented for the determination of tabun, sarin, soman, and VX in aqueous solutions. Extraction recoveries from chloroform were quantitative. Peak area ratios of organophosphorus compounds (OPs) to internal standard versus concentrations of OP were linear over the range of 10-1000 (μg/ml when determined by the flame ionization detector and 10-800 μg/ml when determined by the flame photometric detector. Imprecision occurring at low ng concentrations of VX was caused by its adsorption on the analytical column. Acceptable precision was regained by the addition of a weak base, such as atropine, to the sample extract prior to its injection onto the gas chromatograph (GC).     

Flow injection gas chromatography with sulfur chemiluminescence detection for the analysis of total sulfur in complex hydrocarbon matrixes

A fast and reliable analytical technique for the determination of total sulfur levels in complex hydrocarbon matrices is introduced. The method employed flow injection technique using a gas chromatograph as a sample introduction device and a gas phase dual‐plasma sulfur chemiluminescence detector for sulfur quantification. Using the technique described, total sulfur measurement in challenging hydrocarbon matrices can be achieved in less than 10 s with sample‐to‐sample time <2 min. The high degree of selectivity and sensitivity toward sulfur compounds of the detector offers the ability to measure low sulfur levels with a detection limit in the range of 20 ppb w/w S. The equimolar response characteristic of the detector allows the quantitation of unknown sulfur compounds and simplifies the calibration process. Response is linear over a concentration range of five orders of magnitude, with a high degree of repeatability. The detector's lack of response to hydrocarbons enables direct analysis without the need for time‐consuming sample preparation and chromatographic separation processes. This flow injection‐based sulfur chemiluminescence detection technique is ideal for fast analysis or trace sulfur analysis.     

催化柴油中氮化物分布的气相色谱-原子发射光谱分析方法的研究

建立了催化柴油馏分中各种氮化物类型分布的气相色谱-原子发射光谱(GC-AED)分析方法,考察了色谱条件和不同的试剂气压力对各种氮化物分离和检测灵敏度的影响,定性(或归类)了某典型催化柴油中的73个氮化物,计算了程升条件下各种氮化物的保留指数,为不同实验室的定性比较提供了依据。以峰面积对质量浓度作图,氮化物在2.0~600 mg/L浓度范围内,AED检测器对不同氮化物有良好的线性响应,线性相关系数达0.998。几种氮化物(吲哚、1-甲基吲哚、C2-吲哚、咔唑、1-甲基咔唑、1,8-二甲基咔唑)峰面积的相对标     

气相色谱法测定催化柴油中硫化物类型分布及数据对比

采用气相色谱-氢火焰离子化检测器-硫化学发光检测器（GC—FID—SCD）联用技术,建立了催化柴油中各种硫化物类型分布的分析方法。考察了色谱条件对催化柴油中各种硫化物分离的影响,定性了某催化柴油中的120多个硫化物,该方法还可以同时提供催化柴油中正构烷烃含量的分布信息。硫化物中的硫在1．5—700mg／L时其峰面积与质量浓度呈较好的线性关系,相关系数达0．9999,响应与硫化物的类型无关。催化柴油中苯并噻吩、4-甲基苯并噻吩、二苯并噻吩、4-甲基二苯并噻吩和4,6-二甲基二苯并噻吩等主要硫化物浓度测定的相对标准偏差（RSD）均小于5．0％。当信噪比（S／N）为3时,测得苯并噻吩硫的检出限为0．1mg／L。将该方法用于不同来源柴油中各种硫化物类型分布的研究,并与气相色谱一原子发射光谱检测器（GC—AED）测硫的数据进行了对比,两种检测器的定量结果大多数具有较好的相关性,相关系数大于0．95。     

Rapid and sensitive determination of carbohydrates in foods using high temperature liquid chromatography with evaporative light scattering detection

In the present work, an evaporative light scattering detector was used as a high-temperature liquid chromatography detector for the determination of carbohydrates. The compounds studied were glucose, fructose, galactose, sucrose, maltose, and lactose. The effect of column temperature on the retention times and detectability of these compounds was investigated. Column heating temperatures ranged from 25 to 175°C. The optimum temperature in terms of peak resolution and detectability with pure water as mobile phase and a liquid flow rate of 1 mL/min was 150°C as it allowed the separation of glucose and the three disaccharides here considered in less than 3 min. These conditions were employed for lactose determination in milk samples. Limits of quantification were between 2 and 4.7 mg/L. On the other hand, a temperature gradient was developed for the simultaneous determination of glucose, fructose, and sucrose in orange juices, due to coelution of monosaccharides at temperatures higher than 70°C, being limits of quantifications between 8.5 and 12 mg/L. The proposed hyphenation was successfully applied to different types of milk and different varieties of oranges and mandarins. Recoveries for spiked samples were close to 100% for all the studied analytes.     

A system consisted of flame ionization detector and sulfur chemiluminescence detector for interference free determination of total sulfur in natural gas

A new detection system consisted of a flame ionization detector (FID) and a sulfur chemiluminescence detector (SCD) was developed for sensitive and interference free determination of total sulfur in natural gas by non-separation gas chromatography. In this system, sulfur containing compounds and hydrocarbons were firstly burned in the FID using oxygen rich flame and converted to SO₂, CO₂ and H₂O, respectively. The products from FID were transported into the SCD with hydrogen rich atmosphere wherein only SO₂ could be reduced to SO and reacted with O₃ to produce characteristic chemiluminescence. Therefore, the chemiluminescence of CO found in conventional SCD were eliminated because CO₂ could not be reduced to CO under these conditions. The experimental parameters were systematically investigated. Limit of detection obtained by the proposed system is better than 0.5 μmol/mol for total sulfur and superior to those previously reported. The proposed method not only retains the advantages of the conventional SCD but also provides several unique advantages including no hydrocarbon interference, better stability, and easier calculation. The utility of this technique was demonstrated by the determination of total sulfur in real samples and two certified reference materials (GBW 06332 and GBW (E) 061320).     

催化裂化汽油中硫化物的气相色谱-原子发射光谱分析方法及应用

采用气相色谱-原子发射光谱联用(GC-AED)技术，建立了催化裂化汽油中各种硫化物类型分布的分析方法。考察了色谱条件对催化汽油中各种硫化物分离的影响，定性了催化汽油中的60余种硫化物，首次计算了程序升温条件下汽油馏分中各种硫化物的保留指数，为不同实验室的定性比较提供了依据。该方法可应用于不同来源汽油中各种硫化物类型分布的研究。     

Chlorine-Selective Detection in Supercritical Fluid Chromatography using a Coulson Electrolytic Conductivity Detector

Abstract

A Coulson electrolytic conductivity detector has been coupled successfully to a supercritical fluid chromatograph, providing chlorine-selective detection. This involves minimal modification of the detector and no modification of the SFC or its operation. The general operating parameters of the SFC/CECD system were established by direct injection of three probe compounds: chlordane, γ-lindane, and hexachlorobenzene. Next, the SFC separation of a test mixture containing phenol, γ-lindane, and several chlorinated phenols and related compounds was optimized using UV-Vis and FID detection. The mixture was then separated using the same chromatographic method but with the CECD in line with the UV-Vis detector. The response of the CECD was linear and selective for chlorinated compounds. Limits of detection for the test mixture by CECD ranged from 80 – 250 ng/μL, corresponding to approximately 14 – 44 ng of chlorine on column, and were dependent on chromatographic conditions, but independent of analyte structure.     

A photometric detector driven by beta radiation

It was recently found that typical Chromatographic carrier gases such as argon or nitrogen could be used in a modified flame photometric detector for general or selective determination of eluted molecules. The detector was powered not by a flame but by a radioactively stimulated, mild discharge. The luminescence arose from the second positive system of nitrogen (in argon), and various emissions from aroyl-containing molecules (in nitrogen).This study describes experiments that take away not only the flame but also the discharge: The energy that produces the luminescence is derived solely from the beta decay of⁶³Ni. Because of this low power input, the sensitivity of the present beta-driven photometric detector (-PD) is limited to about 25 ppm of nitrogen (in argon), and to about 5 pg/s for benzaldehyde and other well-responding aroyl compounds (in nitrogen). In accordance with mechanisms postulated earlier, other types of molecules do not produce significant responses in the absence of an electrical field.Material taken from doctoral thesis