Diode-pumped mode-locked femtosecond Tm:CLNGG disordered crystal laser

A diode-end-pumped passively mode-locked femtosecond Tm-doped calcium lithium niobium gallium garnet (Tm:CLNGG) disordered crystal laser was demonstrated for the first time to our knowledge. With a 790 nm laser diode pumping, stable CW mode-locking operation was obtained by using a semiconductor saturable absorber mirror. The disordered crystal laser generated mode-locked pulses as short as 479 fs, with an average output power of 288 mW, and repetition rate of 99 MHz in 2 μm spectral region.     

Cr^4＋：YAG在对撞脉冲锁模的Nd：YAG激光器中实现被动锁模的研究

在理论上提出了Ｃｒ＾４＋：ＹＡＧ作为可饱和吸收体在Ｎｄ：ＹＡＧ激光器中实现被动锁模的可能性，运用速率方程组导出在强激光脉冲作用下Ｃｒ＾４＋：ＹＡＧ激发态吸收的恢复时间和饱和光强。实验上在带有抗共振环结构的接近于介稳腔的脉冲式Ｎｄ：ＹＡＧ激光器中用Ｃｒ＾４＋：ＹＡＧ作为可饱和吸收体实现被动锁模运转，得到能量１３．５ｍＪ、平均脉宽１８０ｐｓ的锁模脉冲序列。     

Environmentally stable all-normal-dispersion femtosecond fiber laser

We demonstrate a mode-locked all-normal-dispersion ytterbium-doped fiber laser constructed with polarization-maintaining fibers. Spectral filtering of a chirped pulse in the cavity, along with a semiconductor saturable absorber, produce self-starting femtosecond mode-locked operation with large normal dispersion. Environmentally stable generation of 2 nJ and 300 fs pulses is achieved.     

60-fs pulses from a diode-pumped Nd:glass laser

We demonstrate 60-fs pulses with an average output power of 84 mW from a diode-pumped Nd:glass laser mode locked by a low-finesse antiresonant Fabry-Perot saturable absorber (A-FPSA). The mode-locked spectrum spreads over most of the available Nd:glass fluorescence bandwidth. At increased pulse energy fluence or decreased negative group-velocity dispersion, multiple pulsing was observed. We experimentally characterize this behavior, which can be explained by the saturation behavior of the A-FPSA and the limited available gain bandwidth. These considerations are significant for the design of saturable absorbers to achieve stable passive mode locking.     

基于混合锁模的耗散孤子掺铒光纤激光器

从一种简单、全光纤结构的混合被动锁模掺铒光纤激光器中,得到了高稳定性、宽光谱的耗散孤子。激光器结合了半导体可饱和吸收体和非线性偏振旋转两种锁模机制,并运行在正常色散区内;通过色散管理,激光器能产生光谱宽度39.1 nm和时域宽度178 fs的孤子脉冲序列。激光输出的中心波长为1.55μm,重复频率约为34.3 MHz,单脉冲能量在0.33 nJ左右。与此同时,激光器的斜效率也约等于15.5%;室温工作下,激光器能实现自启动锁模,且运行在稳定单脉冲输出状态的时长在15 h以上。     

Yb-doped passively mode-locked fiber laser with Bi_2Te_3-deposited

In this study we present an all-normal-dispersion Yb-doped fiber laser passively mode-locked with topological insulator(Bi2Te3) saturable absorber. The saturable absorber device is fabricated by depositing Bi2Te3 on a tapered fiber through using pulsed laser deposition(PLD) technology, which can give rise to less non-saturable losses than most of the solution processing methods. Owing to the long interaction length, Bi2Te3 is not exposed to high optical power, which allows the saturable absorber device to work in a high power regime. The modulation depth of this kind of saturable absorber is measured to be 10%. By combining the saturable absorber device with Yb-doped fiber laser, a mode-locked pulse operating at a repetition rate of 19.8 MHz is achieved. The 3-d B spectral width and pulse duration are measured to be 1.245 nm and317 ps, respectively.     

Single-longitudinal-mode fiber ring laser using fiber grating-based Fabry-Perot filters and variable saturable absorbers

A single-longitudinal-mode (SLM) fiber ring laser is demonstrated by incorporating a fiber Bragg grating (FBG)-based Fabry-Perot (F-P) filter and a variable saturable absorber in a fiber ring cavity. An ultra-narrow bandpass filter is established by the combined mode filtering of the FBG-based F-P filter and the variable saturable absorber. No accurate control for cavity length is required, and stable single longitudinal-mode operation without mode hopping is conveniently achieved.     

Stability regime study of a nonlinear mirror mode-locked laser

A diode array pumped nonlinear mirror mode-locked (ML) laser is developed and the regime of the stable operation for such a system is found to occur for a little detuning of intra-cavity second harmonic phase-matching. The existing theory of mode-locking using a fast saturable absorber (FSA) is used to derive corresponding equivalent parameters for a fast nonlinear mirror saturable absorber. The condition for stable single pulse ML operation is evaluated in terms of small signal gain of the laser medium and small signal nonlinear loss. The analysis explains the experimental observations and differentiates the regime of operation in ML, Q-switching and cw mode-locking.     

Picosecond passively mode-locked GaSb-based semiconductor disk laser operating at 2 μm

We report on a passively mode-locked optically pumped GaSb-based semiconductor disk laser producing stable picosecond optical pulses at a 1.95 μm wavelength. The gain mirror was comprised of a 15 quantum well InGaSb/GaSb structure. A fast semiconductor saturable absorber mirror with three InGaSb/GaSb quantum wells was used to attain self-starting mode-locked operation at a fundamental repetition rate of 881.2 MHz. The laser produced pulses with 30 pJ energy and a duration of 1.1 ps within a factor of 2 of the Fourier limit.     

High-quality, large-area monolayer graphene for efficient bulk laser mode-locking near 1.25 μm

High-quality monolayer graphene as large as 1.2×1.2?cm² was synthesized by chemical vapor deposition and used as a transmitting saturable absorber for efficient passive mode-locking of a femtosecond bulk solid-state laser. The monolayer graphene mode-locked Cr:forsterite laser was tunable around 1.25?μm and delivered sub-100?fs pulses with output powers up to 230?mW. The nonlinear optical characteristics of the monolayer graphene saturable absorber and the mode-locked operation were then compared with the case of the bilayer graphene saturable absorber.     

High-stability passively mode-locked laser based on dual SESAM

A novel passively continuous-wave mode-locked laser by using two semiconductor saturable absorber mirrors (SESAMs) was demonstrated. The obtained average output power was 2.4 W with a pulse width of 9.97 ps and a pulse repetition rate of 127 MHz. The dual-SESAM mode-locked laser operation was more stable than the cases with single SESAM. The experimental results show that the long-term stability of the dual-SESAM mode-locked picosecond lasers provides promising potential for industrial applications.     

Graphene mode-locked femtosecond laser at 2 μm wavelength

We experimentally demonstrated a passively mode-locked femtosecond laser by using a graphene-based saturable absorber mirror (graphene SAM) in the spectral region of 2 μm. The graphene SAM was fabricated by transferring chemical-vapor-deposited, high-quality, and large-area graphene on a highly reflective plane mirror. Stable mode-locked laser pulses as short as 729 fs were obtained with a repetition rate of 98.7 MHz and an average output power of 60.2 mW at 2018 nm.     

Highly efficient, low-cost femtosecond Cr3+ :LiCAF laser pumped by single-mode diodes

We describe efficient continuous-wave (cw) and cw mode-locked operations of a Cr3+ :LiCAF laser, pumped by inexpensive single spatial mode laser diodes. Up to 280 mW of cw output power was obtained with 570 mW of absorbed pump power, with a corresponding slope efficiency of 54%. Continuous tuning between 765 and 865 nm was demonstrated using a fused silica prism. A semiconductor saturable absorber mirror was used to initiate and sustain stable, self-starting, mode-locked operation. In cw mode locking, the laser produced 72 fs (FWHM) duration pulses, and 1.4 nJ pulse energy, at an average output power of 178 mW. Electrical to optical conversion efficiencies of 7.8% in mode-locked operation and 12.2% in cw operation were demonstrated.     

Mode-locked fiber laser with MoSe_2 saturable absorber based on evanescent field

An all-fiber mode-locked fiber laser was achieved with a saturable absorber based on a tapered fiber deposited with layered molybdenum selenide(MoSe_2). The laser was operated at a central wavelength of 1558.35 nm with an output spectral width of 2.9 nm, and a pulse repetition rate of 16.33 MHz. To the best of our knowledge, this is the first report on mode-locked fiber lasers using MoSe_2 saturable absorbers based on tapered fibers.     

基于石墨烯的1 064 nm连续锁模超短脉冲激光器

介绍了利用沉积在增透镜上的石墨烯薄膜作为可饱和吸收体、808 nm激光二极管端面泵浦Nd∶YVO4晶体的1 064 nm连续锁模激光输出特性。采用W型折叠谐振腔结构,在808 nm泵浦功率为8.0 W时,有稳定的连续锁模脉冲输出,平均输出功率达到185 mW;当抽运功率增加到16.0 W时,获得了中心波长1 063.4 nm、脉冲宽度为518 fs、重复频率为66.7 MHz、最大平均输出功率为323 mW的百飞秒量级超短脉冲激光输出。实验结果表明:石墨烯具有优良的可饱和吸收性,在1 064 nm波段能够实现高功率、百飞秒量级连续锁模脉冲激光输出。     

Passively mode-locked diode-pumped Nd:YVO4 oscillator operating at an ultralow repetition rate

We demonstrate the operation of an ultralow-repetition-rate, high-peak-power, picosecond diode-pumped Nd:YVO4 passively mode-locked laser oscillator. Repetition rates lower than 1 MHz were achieved with the use of a new design for a multiple-pass cavity and a semiconductor saturable absorber. Long-term stable operation at 1.2 MHz with a pulse duration of 16.3 ps and an average output power of 470 mW, corresponding to 24-kW peak-power pulses, is reported. These are to our knowledge the lowest-repetition-rate high-peak-power pulses ever generated directly from apicosecond laser resonator without cavity dumping.     

High power passively mode-locked Nd:YVO<Subscript>4</Subscript> laser using graphene oxide as a saturable absorber

We report on a passively mode-locked Nd:YVO₄ laser using a novel graphene oxide saturable absorber fabricated by vertical evaporation method. An 880 nm LD pump source was used to reduce the thermal load of the laser crystal. At the pump power of 7.4 W, 1.2 W average output power of continuous wave mode-locked laser with optical conversion efficiency of 16.2% was achieved. To the best of our knowledge, this is the highest output power of passively mode-locked solid-state laser using graphene oxide saturable absorber. The repetition rate of passively mode-locked pulse was 88 MHz with the pulse energy of 13.6 nJ.     

2μm波段全光纤保偏被动锁模掺铥光纤激光器

报道了2μm波段的全光纤保偏锁模掺铥光纤激光器,通过在法布里-珀罗(F-P)腔内加入半导体可饱和吸收镜做为被动锁模器件,采用主振-放大构型,获得了最高输出平均功率为1.08W,重复频率为10.24MHz,脉冲宽度为15.24ps,中心波长为2054.68nm,光谱宽度约为0.3nm的2μm线偏振激光脉冲输出,激光脉冲的消光比为24.17dB。     

Stable single-longitudinal-mode fiber laser using PM FBG F-P etalon and PM fiber saturable absorber

we present a stable and high efficiency single-longitudinal-mode (SLM) fiber ring laser by using polarization-maintaining fiber Bragg grating Fabry-Perot (PM FBG F-P) etalon combining PM fiber saturable absorber. The PM FBG F-P etalon, which is directly fabricated in hydrogen-loaded PM fiber, is used as reflector and mode-selecting component to reduce the longitudinal-mode density greatly. Meanwhile, a segment un-pumped PM Er³⁺-doped fiber (EDF) serves as saturable absorber to suppress mode hopping and ensure the stable SLM operation. Stable SLM laser output at 1550.4 nm with linewidth of 2.0 kHz is observed. Laser output power is 43.7 mW for a pump power of 148 mW, optical-optical efficiency is 29.5% and signal-to-noise ratio (SNR) is larger than 55 dB.     

Passive mode locking of lasers by crossed-polarization gain modulation

We report on a novel approach for inducing passive mode locking of lasers without using any saturable absorber but exploiting the polarization degree of freedom of light. In our scheme, passive mode locking is achieved by crossed-polarization gain modulation caused by the reinjection of a polarization-rotated replica of the laser output after a time delay. The reinjection time delay defines resonance tongues that correspond to mode-locking operation. Numerical continuation reveals that the cw solution is destabilized through a Hopf bifurcation that defines the onset of multimode operation which evolves sharply into a mode-locked solution. Our approach can be applied to a large variety of laser systems. For vertical-cavity surface-emitting lasers, we demonstrate stable mode-locked pulses at repetition rates in the GHz range and pulse widths of few tens of picoseconds.