Facile preparation of hierarchically porous carbon using diatomite as both template and catalyst and methylene blue adsorption of carbon products

Hierarchically porous carbons were prepared using a facile preparation method in which diatomite was utilized as both template and catalyst. The porous structures of the carbon products and their formation mechanisms were investigated. The macroporosity and microporosity of the diatomite-templated carbons were derived from replication of diatom shell and structure-reconfiguration of the carbon film, respectively. The macroporosity of carbons was strongly dependent on the original morphology of the diatomite template. The macroporous structure composed of carbon plates connected by the pillar- and tube-like macropores resulted from the replication of the central and edge pores of the diatom shells with disk-shaped morphology, respectively. And another macroporous carbon tubes were also replicated from canoe-shaped diatom shells. The acidity of diatomite dramatically affected the porosity of the carbons, more acid sites of diatomite template resulted in higher surface area and pore volume of the carbon products. The diatomite-templated carbons exhibited higher adsorption capacity for methylene blue than the commercial activated carbon (CAC), although the specific surface area was much smaller than that of CAC, due to the hierarchical porosity of diatomite-templated carbons. And the carbons were readily reclaimed and regenerated.     

Crosslinking of epoxy resins at interfaces. IV. Anhydride-cured resins at carbon and graphite surfaces

Dispersions of carbon blacks and chopped carbon fibers in epoxy resins may be characterized by infrared internal reflection spectroscopy (IR–IRS). The high surface areas of the carbons (often ≥ 100 m²/g) ensure a high degree of interfacial contact between the carbon surface and the polymer. The crosslinking kinetics and final crosslinked state of an anhydride-cured epoxy resin are shown to be affected strongly by the carbons through adsorption of the tertiary amine catalyst at oxidation sites on the carbon surface. Oxidative treatments of the carbons (nitric acid oxidation, air oxidation) increase the effect on the crosslinking chemistry. Carbon dioxide treatment of the carbons, which produces a basic surface, reduces the effect on the crosslinking. The effects on the crosslinking kinetics were confirmed by differential scanning calorimetry (DSC). The relevance of these results to the characterization of the interphase in carbon fiber/epoxy composites is discussed.     

An investigation of the activity of carbon blacks recovered from elastomer composites

The activity of carbon blacks recovered from elastomer systems is determined by use of a temperature jump technique imposed on the carbon blacks in air using a TG unit. The elastomer composites were composed of styrene-butadiene rubber (SRR), fillers, activators, accelerators together with a number of different carbon blacks. The organic content was pyrolyzed away by heating in nitrogen, the atmosphere was changed to air and the activity of the carbons was assessed by the temperature jump method. This enables the Arrhenius parameters to be established for the gasification of the carbons in air. This data was compared with the oxidation rates of carbons before they were introduced into the elastomer system. Nitrogen adsorption surface areas based on a BET analysis showed that the surface area of the carbons was similar before and after incorporation into the composite. The kinetic parameters of the carbons were however somewhat altered by incorporation into the elastomer systems, but their order of activity towards the gasification process as assessed by their relative rate of gasification remained the same. This is explained by postulating that the higher rates of oxidation is associated with the present of edge carbon atoms at the surface compared to the much slower oxidation rates of the “basel” plane carbon atoms. It appears that this surface structure is largely retained in the composite carbon-elastomer system. This enables some speculation regarding the reinforcing action of certain carbon blacks in the composite system.     

Surface functionalization of ordered mesoporous carbons--a comparative study

Hexagonally structured mesoporous carbons C15 and CMK-5 and cubically structured carbon C48 were synthesized using ordered silica SBA-15 and MCM-48 as templates and carbon precursors of different structures. The surfaces of these ordered carbons were chemically functionalized by employing an approach, in which the selected diazonium compounds were in situ generated and reacted with the carbon frameworks of the mesoporous carbons. The aromatic organic molecules containing chlorine, ester, and alkyl groups were covalently attached to the surface of these ordered mesoporous carbons. The presence of functional groups on the modified carbons was confirmed with Fourier transform infrared spectroscopy, thermogravimetric analysis, and nitrogen adsorption. The BET-specific surface area and the pore width of ordered carbons were significantly reduced, whereas the primary structure of these ordered carbons and their unit cells were intact. Basically, the density of grafted functional groups is related to the specific surface area of the sample, particularly the surface area of mesopores. The surface functionalization reaction takes place only on the external surface of carbon C15, while it occurs on both of the internal and external surface of CMK-5 carbon with the nanopipe structure. The presence of the micropores in CMK-5 carbon should be responsible for its lower grafting density because the small micropores are inaccessible in the reaction. It was also proposed that the preferred adsorption/reaction in C48 may be related to the observed unsymmetrical degradation of the XRD patterns for the functionalized C48 samples. The chemical modification process considerably reduced the primary mesopores in these ordered carbons by approximately 1-1.5 nm, affording carbons with micropores in the cases of C15 and C48, and mixed micropores and small mesopores in the case of CMK-5. A grafting density of approximately 0.9-1.5 micromol/m(2) was achieved under current research.     

稻壳制备多孔炭对肌酐的吸附

研究了具有高比表面积稻壳基多孔炭(简称RHC)对人体内代谢产物肌酐(简称CR)的吸附, 将采用氢氧化钠活化稻壳制备的四种多孔炭和二种商业活性炭对肌酐的吸附进行了对比, 同时考察了盐酸、硝酸和双氧水对多孔炭进行表面处理及其经过高温处理(800 ℃)后对肌酐的吸附. 结果表明稻壳基多孔炭对肌酐的吸附超过商业炭,经过表面处理后多孔炭的吸附能力增强, 无氧化性盐酸处理后的多孔炭对肌酐的吸附量最大, 氧化性最强的硝酸处理后的多孔炭对肌酐的吸附量最小, 双氧水居中, 高温处理后的多孔炭吸附能力有所降低. 实验证实了多孔炭对CR的吸附符合Freundlich方程.     

ACTIVATION ENERGY OF DESORPTION OF DIBENZOFURAN ON ACTIVATED CARBONS

Three kinds of commercial activated carbons, such as Norit RBI, Monolith and Chemviron activated carbons, were used as adsorbents for adsorption of dibenzofiuran. The average pore size and specific surface area of these activated carbons were measured Temperature Programmed Desorption (‘TPD) experiments were conducted to measure the TPD curves of dibenzofuran on the activated carbons, and then the activation energy for desorption of dibenzofuran on the activated carbons was estimated. The results showed that the Chemviron and the Norit RB1 activated carbon maintained higher specific surface area and larger micropore pore volume in comparison with the Monolith activated carbon, and the activation energy for the desorption of dibencofuran on these two activated carbons was higher than that on the Monolith activated carbon. The smaller the pore of the activated carbon was, the higher the activated energy of dibenzofiuran desorption was.     

ACTIVATION ENERGY OF DESORPTION OF DIBENZOFURAN ON ACTIVATED CARBONS

1. INTRODUCTION With the development of municipalization in China, more and more cities are challenged by the problem of how to dispose of the dramatically increased municipal waste. Generally, most of municipal solid waste is landfilled or dumped openly in the suburbs. It causes not only land waste, but also serious environment pollution. In order to solve efficiently the environment pollution caused by municipal solid waste, incineration technique was introduced in some big cities such…     

Importance of structural and chemical heterogeneity of activated carbon surfaces for adsorption of dibenzothiophene

The performance of various activated carbons obtained from different carbon precursors (i.e., plastic waste, coal, and wood) as adsorbents for the desulfurization of liquid hydrocarbon fuels was evaluated. To increase surface heterogeneity, the carbon surface was modified by oxidation with ammonium persulfate. The results showed the importance of activated carbon pore sizes and surface chemistry for the adsorption of dibenzothiophene (DBT) from liquid phase. Adsorption of DBT on activated carbons is governed by two types of contributions: physical and chemical interactions. The former include dispersive interactions in the microporous network of the carbons. While the volume of micropores governs the amount physisorbed, mesopores control the kinetics of the process. On the other hand, introduction of surface functional groups enhances the performance of the activated carbons as a result of specific interactions between the acidic centers of the carbon and the basic structure of DBT molecule as well as sulfur-sulfur interactions.     

Carbon-13 NMR of fluorocyclopropanes

Carbon-13 and hydrogen NMR data are presented for several cyclopropanes with one to four fluorine atoms attached to the ring. Substituents directly attached to a ring carbon are found to unshield that carbon to an extent increasing with their electronegativity, but remote substituents may have an opposite effect. Relative orientation of the substituent groups, especially if they are bulky, also has a strong influence on the ring-carbon shifts. Chemical shifts of carbons in methyl groups attached to the ring change to an extent which is additive in the effects of gem and cis substituents. One-bond coupling of ring carbons with fluorines is affected both by geminal and vicinal substituents, in a way generally related to their electronegativity. It is tentatively concluded that two-bond coupling between ring carbons and ring-attached fluorines depends in magnitude primarily on what groups are cis to the fluorine. Two-bond coupling between a carbon atom in a ring-attached methyl and the hydrogen gem to the methyl appears to be vanishingly small, but there is appreciable three-bond coupling of the methyl carbons to vicinal hydrogens.     

活性炭液相吸附去除噻吩硫化物的研究

迄今为止,国内外降低汽油硫含量的方法主要有原料加氢脱硫、汽油加氢脱硫、溶剂抽提脱硫、催化裂化脱硫、氧化脱硫、生物脱硫、吸附脱硫及组合技术,同时一些非常规技术如膜过程脱硫、等离子体和光脱硫也在积极探索之中。     

Cadmium ion adsorption on different carbon adsorbents from aqueous solutions. Effect of surface chemistry, pore texture, ionic strength, and dissolved natural organic matter

Adsorption of Cd(II) species at pH = 5 was studied on three carbon adsorbents: granular activated carbon, activated carbon fiber, and activated carbon cloth. As-received and oxidized adsorbents were used. Cd(II) adsorption greatly increased after oxidation due to the introduction of carboxyl groups. The use of a buffer solution to control the pH introduced some changes in the surface chemistry of carbons through the adsorption of one of the compounds used, biphthalate anions. The increase in ionic strength reduced Cd(II) uptake on both as-received and oxidized carbons due to a screening of the electrostatic attractions between the Cd(II) positive species and the negative surface charge, which in the case of as-received carbons derived from the biphthalate anions adsorbed and in the oxidized ones from the carboxyl groups. Tannic acid was used as a model compound for natural organic matter. Its adsorption was greatly reduced after oxidation, and most of the carbon adsorbents preadsorbed with tannic acid showed an increase in Cd(II) uptake. In the case of competitive adsorption between Cd(II) species and tannic acid molecules, there was a decrease in Cd(II) uptake on the as-received carbon whereas the contrary occurred with the oxidized carbons. These results illustrate the great importance of carbon surface chemistry in this competitive adsorption process. Finally, under all experimental conditions used, when the adsorption capacity of carbons was compared under the same conditions it increased in the following order: granular activated carbon < activated carbon fiber < activated carbon cloth.     

Adsorption of sodium dodecylbenzenesulfonate on activated carbons: effects of solution chemistry and presence of bacteria

The objective of the present investigation was to determine the effectiveness of activated carbon in removing sodium dodecylbenzenesulfonate (SDBS) and to analyze the chemical and textural characteristics of the activated carbons that are involved in the adsorption process. Studies were also performed on the influence of operational variables (pH, ionic strength, and presence of microorganisms) and on the kinetics and interactions involved in the adsorption of this pollutant on activated carbon. The kinetics study of SDBS adsorption revealed no problems in its diffusion on any of the activated carbons studied, and Weisz-Prater coefficient (C WP) values were considerably lower than unity for all activated carbons studied. SDBS adsorption isotherms on these activated carbons showed that: (i) adsorption capacity of activated carbons was very high (260-470 mg/g) and increased with larger surface area; and (ii) dispersive interactions between SDBS and carbon surface were largely responsible for the adsorption of this pollutant. SDBS adsorption was not significantly affected by the solution pH, indicating that electrostatic adsorbent-adsorbate interactions do not play an important role in this process. The presence of electrolytes (NaCl) in the medium favors SDBS adsorption, accelerating the process and increasing adsorption capacity. Under the working conditions used, SDBS is not degraded by bacteria; however, the presence of bacteria during the process accelerates and increases SDBS adsorption on the activated carbon. Microorganism adsorption on the activated carbon surface increases its hydrophobicity, explaining the results observed.     

Carbon exchange in hot alkaline degradation of glucose

The decomposition of 1-13C-D-glucose, 6-13C-D-glucose, and 1-13C-sodium lactate has been studied in hot (145 +/- 3 degrees C) alkaline (3.5 M) sodium hydroxide solution in order to understand the mechanisms of carbon exchange in the alkaline degradation of glucose. The results show that in the formation of lactate from glucose the carboxylate (COO-) carbon is formed preferentially from C1 carbons but methyl (CH3) carbon is formed preferentially from C6 carbons. However, on further decomposition of lactate to ethanol and carbonate, 13C-labeled carboxylate (COO-) is scrambled equally among carbonate and both carbons in product ethanol molecules. In the production of glycolate, the labeled C1 carbon mainly ends up as carboxylate (COO-) carbon, while for C6-labeled glucose the labeled carbon mainly ends up as alcoholic (CH2OH) carbon. In the production of acetate and formate there is also discrimination between C1 and C6 label.     

Proximity and the heteroatom effects on the carbon-13 chemical shifts of methyl-substituted phenols,anilines and thiophenols

Upfield substituent-induced ¹³C chemical shifts for aryl carbons of polymethyl substituted benzenes, phenols, anilines and thiophenols were investigated as a function of the proximity between substituents X and CH₃ (X = CH₃, NH₂, OH and SH). The results indicate that the induced shifts of the substituted aryl carbons are, in general, independent of the polar substituent but depend on the number of adjacent substituted aryl carbons. A ?2.0 ppm upfield shift was found for a substituted aryl carbon adjacent to one substituted aryl carbon and a ?3.8 ppm upfield shift for a substituted aryl carbon bound by two substituted aryl carbons. It is suggested that the near additivity of the upfield shifts is the result of changes in the bond order between the aromatic ring carbons in the region of the substituted aryl carbons due to distortion of the ring. The ¹³C chemical shifts of the methyl substituents for methyl substituted phenols, anilines and thiophenols were determined, and it was found that the values could be predicted from the additivity parameters reported for the analogous methylbenzenes plus an additional pair-interaction term associated with the through-space electronic influence of the heteroatom.     

Directed modification of carbons of varied origin and chemical nature of the surface in order to control their catalytic activity

Simple methods were suggested and conditions were found under which modified carbon materials with varied chemical nature of the surface and controllable catalytic activity in the model reaction of hydrogen peroxide decomposition can be produced from various raw materials. The pore structure parameters of the carbons synthesized were determined, the kinetics of the reaction under study on these carbons was analyzed, and the possibility of synthesis of carbon catalysts with high catalytic activity exceeding that of the known active carbons was demonstrated.     

The physical and surface chemical characteristics of activated carbons and the adsorption of methylene blue from wastewater

Adsorption of a basic dye, methylene blue, from aqueous solutions onto as-received activated carbons and acid-treated carbons was investigated. The physical and surface chemical properties of the activated carbons were characterized using BET-N(2) adsorption, X-ray photoelectron spectroscopy (XPS), and mass titration. It was found that acid treatment had little effect on carbon textural characteristics but significantly changed the surface chemical properties, resulting in an adverse effect on dye adsorption. The physical properties of activated carbon, such as surface area and pore volume, have little effect on dye adsorption, while the pore size distribution and the surface chemical characteristics play important roles in dye adsorption. The pH value of the solution also influences the adsorption capacity significantly. For methylene blue, a higher pH of solution favors the adsorption capacity. The kinetic adsorption of methylene blue on all carbons follows a pseudo-second-order equation.     

Cyclodextrins adsorbed onto activated carbons: preparation, characterization, and effect on the dispersibility of the particles in water

We have investigated the adsorption equilibrium of selected cyclodextrins onto activated carbons. A number of parameters were examined including the type of carbon material, the size of macrocyclic cavity, and the chemical nature of the oligosaccharide (e.g., neutral, anionic, or cationic cyclodextrin). Adsorption isotherm studies revealed that the maximum amount of cyclodextrin immobilized on the carbon surface is obtained for the native β-CD, while the adsorption capacity of the ionic cyclodextrins derivatives strongly depends on the net surface charge of the activated carbon. The affinity of cyclodextrins for activated carbons was further utilized to prepare modified activated carbons containing controlled amounts of cyclodextrins through an adsorption process. The resulting materials were characterized by N(2) adsorption-desorption volumetric measurements, FTIR and Raman spectroscopy, while the quantitative determination of the oligosaccharide content on activated carbons was performed by gravimetric measurements. On the basis of the Turbiscan results, it was found that the chemical structure of cyclodextrins, which are incorporated in the carbon framework, had significant influence on the dispersibility and stabilization of the solid particles in water. Agglomeration and precipitation of the carbon particles were markedly suppressed with substituted cyclodextrins whose hydroxyl groups were partially substituted by methyl or alkylammonium groups.     

13C-NMR分析混合酸处理脱灰对永兴褐煤结构的影响

运用煤的结构化学理论和固态 ¹³C-NMR的研究方法,对比分析了永兴褐煤在混合酸处理脱灰前后碳组成的变化。研究表明,混合酸处理脱灰对永兴褐煤中脂肪碳和芳香碳两者比例分配的影响并不大,但对季碳、环内氧接脂碳、芳香桥碳和羧基碳的破坏作用比较明显;在芳香桥碳锐减的同时,芳甲基的比例非但没有减少反而略有增加,表明永兴褐煤中的双环及多环结构被破坏为单环结构,芳香簇的尺寸变小了,这是混合酸处理脱灰对永兴褐煤结构最重要的影响。     

Comparative Study of the Adsorption from Aqueous Solutions and the Desorption of Phenol and Nonylphenol Substrates on Activated Carbons

Adsorption of phenol and nonylphenol from aqueous solutions on microporous activated carbons has been studied. The phenol isotherm changes from L-shaped for surface oxygen group free carbon (I sample) to a two-stepped isotherm for oxidized carbon (IN sample, HNO(3) treated) Furthermore, the adsorbed amounts diminish in about 25% on IN carbon. It is proposed that a change in the adsorption mechanism take place; i.e., weak interaction forces between the pi electrons in phenol and the pi electron in carbon are present on the original I carbon, while a donor-acceptor complex on the oxidized IN carbon is operating between basic surface oxygen groups and phenol aromatic rings. The shape of nonylphenol isotherms is two-stepped for both carbons. The introduction of acidic oxygen surface groups on the carbon enhances the specific nonylphenol adsorption by about 40%. This may be interpreted as being due to the fact that nonylphenol is hydrogen-bonded to the oxidized carbon surface by means of acidic groups. Thermal desorption experiments indicate that phenol is mainly physisorbed. Thermal desorption further confirms that nonylphenol is possibly bonded to oxygen surface groups by hydrogen bonds. Copyright 2001 Academic Press.     

Effects of Cetylpyridinium Chloride on Phase and Rheological Behavior of the Diluted C(12)E(4)/Benzyl Alcohol/Water System

The influence of the pore size distribution of activated carbon on the adsorption of phenol from aqueous solutions was explored. Activated carbons with different porous structures were prepared by gasifying a bituminous coal char to different extents of burn-off. The results of adsorption experiments show that the phenol capacity of these carbons does not proportionally increase with their BET surface area. This reflects the heterogeneity of the carbon surface for adsorption. The pore size distributions of these carbons, determined according to the Dubinin-Stoeckli equation, were found to vary with the burn-off level. By incorporating the distribution with the Dubinin-Radushkevich equation using an inverse proportionality between the micropore size and the adsorption energy, the isotherms for the adsorption of phenol onto these carbons can be well predicted. The present study has demonstrated that the heterogeneity of carbon surface for the phenol adsorption can be attributed to the different energies required for adsorption in different-size micropores. Copyright 2000 Academic Press.