On the Adsorption of Some Catechol Derivatives from Aqueous Solutions onto Activated Carbon Cloth: Equilibrium and Kinetic Studies

The removal of some of pollutants including catechol, 3-methylcatechol, 3-methoxycatechol, and 2,3-dihydroxybenzoic acid by adsorption onto activated carbon cloth (ACC) at 35.0 ± 0.1°C was investigated. The equilibrium experimental data were fitted to Langmuir, Freundlich, Temkin, Langmuir-Freundlich, and Redlich-Peterson isotherms. Also the kinetic experimental data were fitted to the pseudo-first-order and pseudo-second-order kinetic models. It was found that the pseudo-second-order model describes the kinetic of adsorption better than the other one. By comparing the obtained results with the previously reported data, it can be concluded that ACC is a high efficient adsorbent for removal of phenolic compounds from aqueous solutions.     

Microwave assisted preparation of efficient activated carbon from grapevine rhytidome for the removal of methyl violet from aqueous solution

Grapevine rhytidome (the outer layer of bark on trunk), as an abundant and low-cost precursor, was used to prepare granular activated carbon with high surface area for the removal of methyl violet from aqueous solution. Microwave heating source was used to reduce the treatment time and energy consumption. To optimize the preparation, the effects of the different parameters, such as phosphoric acid concentration, acid/precursor weight ratio, impregnation time, microwave power, radiation time, and oven heating time on the ability of the samples for removal of methyl violet were studied. The obtained activated carbon was characterized by N₂ adsorption/desorption, SAXS, TEM and SEM methods. The adsorption of methyl violet onto the activated carbon was studied from both equilibrium and kinetic point of view and the results were compared with the commercial granular activated carbon. The rate of adsorption onto the prepared activated carbon was faster than commercial activated carbon. Different kinetic models were used to analyze the experimental kinetic data. The obtained activated carbon showed higher adsorption capacity (more than twice) for the adsorption of methyl violet in comparison with the commercial one. The equilibrium data were analyzed using different isotherm models. Adsorption was found to be maximum in the pH range 7-9.     

Kinetic modeling of liquid-phase adsorption of reactive dyes on activated carbon

In this paper, adsorption equilibrium and kinetics of three reactive dyes from their single-component aqueous solutions onto activated carbon were studied in a batch reactor. Effects of the initial concentration and adsorbent particle size on adsorption rate were investigated Adsorption equilibrium data were then correlated with several well-known equilibrium isotherm models. The kinetic data were fitted using the pseudo-first-order equation, the pseudo-second-order equation, and the intraparticle diffusion model. The respective characteristic rate constants were presented. A new adsorption rate model based on the pseudo-first-order equation has been proposed to describe the experimental data over the whole adsorption process. The results show that the modified pseudo-first-order kinetic model generates the best agreement with the experimental data for the three single-component adsorption systems.     

Comparative Adsorption of Crystal Violet and Congo Red onto ZnCl2 Activated Carbon

In this study, the adsorption characteristics of crystal violet (CV) and Congo red (CR) dyes from the aqueous solution onto prepared activated carbon were examined. The activated carbon was prepared from wood apple shell by chemical activation with ZnCl₂. The parameters studied were the effect of contact time, initial dyes concentration, and pH of solution. The experimental equilibrium data were analyzed and fitted to Langmuir, Freundlich, and Temkin isotherms. The maximum monolayer adsorption capacities of CV and CR dyes were found to be 142.85 and 83.33 mg per gram of prepared activated carbon at 298 K. The kinetic data obtained at different concentrations were analyzed using pseudo-first-order, pseudo-second-order, and intra-particle diffusion models. Batch adsorption kinetic studies showed that the adsorption of dyes followed pseudo-second-order kinetics and at four different concentrations of both dyes, indicating that chemisorption is the rate-limiting step. Thermodynamic studies reveal that the removal of dyes from aqueous solution onto activated carbon was a spontaneous, feasible, and endothermic process at a temperature greater than standard equilibrium temperature.     

Mesoporous Carbons of Well-Organized Structure in the Removal of Dyes from Aqueous Solutions

Mesoporous carbons with differentiated properties were synthesized by using the method of impregnation of mesoporous well-organized silicas. The obtained carbonaceous materials and microporous activated carbon were investigated by applying different methods in order to determine their structural, surface and adsorption properties towards selected dyes from aqueous solutions. In order to verify applicability of adsorbents for removing dyes the equilibrium and kinetic experimental data were measured and analyzed by applying various equations and models. The structural and acid-base properties of the investigated carbons were evaluated by Small-Angle X-ray Scattering (SAXS) technique, adsorption/desorption of nitrogen, potentiometric titration, and Transmission Electron Microscopy (TEM). The results of these techniques are complementary, indicating the type of porosity and structural ordering, e.g., the pore sizes determined from the SAXS data are in good agreement with those obtained from nitrogen sorption data. The SAXS and TEM data confirm the regularity of mesoporous carbon structure. The adsorption experiment, especially kinetic measurements, reveals the utility of mesoporous carbons in dye removing, taking into account not only the adsorption uptake but also the adsorption rate.     

纳米TiO2分离富集Mo(Ⅵ)和Re(Ⅶ)

本文研究了纳米TiO2吸附剂对Mo(VI)、Re(VII)的吸附行为,考察了溶液的pH值、吸附时间、温度等因素对吸附的影响。结果表明：纳米TiO2对Mo(VI)的吸附在pH 1～8条件下,吸附率超过99%,2 mL 0.05mol/L NaOH溶液可将吸附的Mo(VI)离子完全洗脱,解吸率能达到97%。在pH 1～10范围内,纳米TiO2不吸附Re(VII), 从而达到Mo(VI)、Re(VII)分离。在2℃～50℃温度范围内,Mo(VI)的吸附过程符合Langmiur等温式,纳米TiO2对Mo(VI)的最大吸附容量从11.51mg g-1增加到14.19 mg g-1;纳米TiO2分离钼后,溶液剩余的铼,用活性炭吸附,在pH1～10范围内, Re(VII)的吸附率可达99%,用浓氨水进行洗脱,洗脱率可达96%;吸附过程可用准二级反应动力学模型描述,是以化学吸附为控制步骤的吸附过程;吸附等温线与Freundlich模型有较好的拟合。     

A Film-Pore-Surface Diffusion Model for the Adsorption of Acid Dyes on Activated Carbon

The sorption of acid dyes from aqueous effluents onto activated carbon has been studied. The effects of initial dye concentration and activated carbon mass on the rate of Acid Blue 80, Acid Red 114 and Acid Yellow 117 removal have been investigated. A three-resistance mass transport model based on film, pore and surface diffusion control has been applied to model the concentration decay curves. The model incorporates an effective diffusion coefficient D _eff, which is dependant on the equilibrium solid phase concentration or fractional surface coverage. The results of the film-pore-surface diffusion model are compared with the data obtained from the basic film-pore diffusion model. It has been found that the film-pore-surface diffusion model provides a major improvement over the data correlated by the film-pore diffusion model. Also, the relationship between surface diffusion and fractional surface coverage has been investigated for the adsorption of acid dyes on activated carbon.     

A Film-Pore-Surface Diffusion Model for the Adsorption of Acid Dyes on Activated Carbon

The sorption of acid dyes from aqueous effluents onto activated carbon has been studied. The effects of initial dye concentration and activated carbon mass on the rate of Acid Blue 80, Acid Red 114 and Acid Yellow 117 removal have been investigated. A three-resistance mass transport model based on film, pore and surface diffusion control has been applied to model the concentration decay curves. The model incorporates an effective diffusion coefficient D _eff, which is dependant on the equilibrium solid phase concentration or fractional surface coverage. The results of the film-pore-surface diffusion model are compared with the data obtained from the basic film-pore diffusion model. It has been found that the film-pore-surface diffusion model provides a major improvement over the data correlated by the film-pore diffusion model. Also, the relationship between surface diffusion and fractional surface coverage has been investigated for the adsorption of acid dyes on activated carbon.     

Liquid phase adsorption of Congo red dye on functionalized corn cobs

This study investigates the adsorption of Congo red (CR) dye onto corn cob based activated carbon (CCAC) in the batch process. The activated carbon was characterized using FTIR, SEM, and EDX techniques, respectively. The effect of operational parameters such as the initial dye concentration (10–50?mg/L), contact time (5–160 minutes), and solution temperature (30–50°C) were studied. The amount of the CR dye adsorbed was found to increase as these operational parameters increased. Kinetic data for CR dye adsorption onto CCAC were best represented by the pseudo second-order kinetic model. Four different isotherms namely Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich models were used to test the adsorption data. It fitted the Langmuir isotherm model most. Thermodynamic parameters such as ΔH⁰, ΔS⁰, and ΔG⁰ were evaluated. The adsorption process was found to be exothermic and spontaneous. The study shows that CCAC is an effective adsorbent for the adsorption of CR dye from aqueous solution.     

Novel three-stage kinetic model for aqueous benzene adsorption on activated carbon

We propose a novel kinetic model for adsorption of aqueous benzene onto both granular activated carbon (GAC) and powdered activated carbon (PAC). The model is based on mass conservation of benzene coupled with three-stage adsorption: (1) the first portion for an instantaneous stage or external surface adsorption, (2) the second portion for a gradual stage with rate-limiting intraparticle diffusion, and (3) the third portion for a constant stage in which the aqueous phase no longer interacts with activated carbon. An analytical solution of the kinetic model was validated with the kinetic data obtained from aqueous benzene adsorption onto GAC and PAC in batch experiments with two different solution concentrations (C(0)=300 mg L(-1), 600 mg L(-1)). Experimental results revealed that benzene adsorption for the two concentrations followed three distinct stages for PAC but two stages for GAC. The analytical solution could successfully describe the kinetic adsorption of aqueous benzene in the batch reaction system, showing a fast instantaneous adsorption followed by a slow rate-limiting adsorption and a final long constant adsorption. Use of the two-stage model gave incorrect values of adsorption coefficients in the analytical solution due to inability to describe the third stage.     

Oxalic acid removal from wastewater using multi-walled carbon nanotubes: Kinetic and equilibrium analysis

Oxalic acid adsorption from aqueous solution is studied in this work. Multi-walled carbon nanotubes (MWCNT) were used as an adsorbent. The investigated adsorption variables are equilibrium time, initial acid concentration, and temperature. The experimental results were presented using equilibrium isotherm and kinetic models. The used equilibrium models are Langmuir, Freundlich, and Temkin adsorption isotherms. And the kinetic models are Elovich, Lagergren pseudo-first-order and pseudo-second-order kinetic models. The thermodynamics studies were carried out at three different temperatures: 278, 298, and 318 K. Langmuir isotherm was the best fitted equilibrium model for the experimental data. The all applied kinetic models fitted the data suitably.     

Adsorption of Pb(II) and Ni(II) From Aqueous Solution by a High-Capacity Industrial Sewage Sludge-Based Adsorbent

In the present study, adsorption of Ni(II) and Pb(II) from aqueous solution was investigated using activated carbon synthesized with industrial wastewater sludge. The synthesized adsorbent was analyzed using nitrogen adsorption–desorption and Fourier transfer infrared (FTIR) techniques. Batch adsorption mode was used to evaluate the effect of solution pH, contact time, adsorbent dose, initial metal ion concentration, and temperature on the adsorption capacity of the synthesized adsorbent. The kinetic data were analyzed using different kinetic models. The pseudo-second-order equation gave the best fit to the experimental data for both metal ions. The equilibrium isotherm data were analyzed using the Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherm models. The results showed that the data obtained for the Ni(II) and Pb(II) adsorption are in good agreement with the Langmuir model. The Langmuir mono-layer maximum adsorption capacities for Ni(II) and Pb(II) ions were estimated to be 74.06 and 88.76 mg g^?1 at 25°C, respectively. In addition, the thermodynamic studies proved that the adsorption process of both metals could be considered endothermic.     

Influence of Initial pH Value on the Adsorption of Reactive Black 5 Dye on Powdered Activated Carbon: Kinetics,Mechanisms, and Thermodynamics

The aim of this work was to investigate the influence of initial pH value (pH₀) on the isothermal adsorption of Reactive Black 5 (RB5) dye on commercial powdered activated carbon. Four initial pH values were chosen for this experiment: pH₀ = 2.00, 4.00, 8.00, and 10.00. In order to investigate the mechanism of adsorption kinetic, studies have been performed using pseudo-first-order and pseudo-second-order kinetic models as well as an intraparticle diffusion model. In addition, thermodynamic parameters of adsorption were determined for pH₀ = 4.00. Results of this research showed that the initial pH value significantly influences the adsorption of RB5 dye onto activated carbon. The highest adsorption capacities (q_e) and efficiencies of decolouration were observed for initial pH values of pH₀ = 2.00 (q_e = 246.0 mg g⁻¹) and 10.00 (q_e = 239.1 mg g⁻¹) due to strong electrostatic interactions and attractive π···π interactions, respectively. It was also shown that the adsorption of RB5 dye on activated carbon at all initial pH values is kinetically controlled, assuming a pseudo-second-order model, and that intraparticle diffusion is not the only process that influences on the adsorption rate.     

Adsorption of urea onto granular activated alumina: A comparative study with granular activated carbon

ABSTRACT

This study investigated the ability of granular activated alumina to remove urea from wastewater through adsorption, and compared its performance with granular activated carbon. XRF, EDX, XRD, and TGA were used to investigate the adsorbents. The removal of urea as a function of pH value was studied. The point of zero charge for activated alumina was found to be 8.8, while that for activated carbon was found to be 7.1. The experimental data of the adsorption process were explored by fitting to different kinetic models to determine the adsorption kinetics and mechanisms. Then, the equilibrium data were examined by fitting to various two-parameter and three-parameter isotherm models. Results showed that the removal efficiency increased with the increasing pH value. The maximum removal efficiencies were 24% and 31% for granular activated alumina and granular activated carbon, respectively, at pH?=?9.0. Kinetic studies showed that adsorption of urea onto both activated alumina and activated carbon can be expressed by pseudo second order kinetics. Equilibrium studies showed that the adsorption isotherms could be expressed by the Redlich-Peterson isotherm and Temkin isotherm for activated alumina and activated carbon, respectively. Adsorbents were investigated using FTIR and SEM, and results showed the occurrence of adsorption.     

Adsorptive characteristics of isoniazid on powdered activated carbon: π–π Dispersion interactions at the solid–solution interface

The presence of antibiotic residues in the aquatic environment poses a potential risk to living organisms due to the development of antibiotic resistance in bacteria. In the present study, the removal of isoniazid by commercial powdered activated carbon was studied in aqueous solutions. The adsorption experiments were done as a function of time, concentration, temperature, and pH in order to understand the adsorption mechanism. The Langmuir and the Freundlich isotherms were used to model the equilibrium data. The results showed that isoniazid was physisorbed on the surface of the activated carbon by π–π dispersion interactions.     

Adsorption equilibrium and kinetics of copper ions and phenol onto modified adsorbents

The adsorption equilibrium and kinetics of single and binary component copper ions and phenol onto powdered activated carbon (PAC), alginate beads and alginate-activated carbon beads (AAC) were studied. Adsorption equilibrium data for single component copper ions and phenol onto the adsorbents could be represented by the Langmuir equation. Multicomponent equilibrium data were correlated by the extended Langmuir and ideal adsorbed solution theory (IAST). The IAST gave the best fit to our data. The amount of copper ions adsorbed onto the AAC beads in the binary component was greater than that of phenol. The internal diffusion coefficients were determined by comparing the experimental concentration curves with those predicted from surface diffusion and pore diffusion model.     

Adsorption of benzoic acid onto high specific area activated carbon cloth

The adsorption of benzoic acid from aqueous solution onto high area carbon cloth at different pH values has been studied. Over a period of 125 min the adsorption process was found to follow a first-order kinetics and the rate constants were determined for the adsorption of benzoic acid at pH 2.0, 3.7, 5.3, 9.1, and 11.0. The extents of adsorption and the percentage coverage of carbon cloth surfaces were calculated at 125 min of adsorption. Adsorption isotherms at pH values of 2.0, 3.7, and 11.0 were derived at 25 degrees C. Isotherm data were treated according to Langmuir and Freundlich equations and the parameters of these equations were evaluated by regression analysis. The fit of experimental isotherm data to both equations was good. It was found that both the adsorption rate and the extent of adsorption at 125 min were the highest at pH 3.7 and decreased at higher or lower pH values. The types of interactions governing in the adsorption processes are discussed considering the surface charge and the dissociation of benzoic acid at different pH values.     

Optimization of sulfamethazine sodium adsorption onto activated carbon-based Salix psammophila: investigation of adsorption behavior and mechanism

A study on the adsorption of sulfamethazine sodium (SMS) from aqueous solution onto the activated carbon (AC)-based Salix psammophila (SP) by phosphoric acid activation was conducted. The central composite design under response surface methodology was employed for the removal of SMS and the process parameters were optimized. Influence of adsorbent dose, initial concentration of SMS, contact time and solution pH on the adsorption capacity of AC was investigated. The optimum adsorption conditions were obtained using adsorbent dosage of 0.54?g/L, initial concentration of 322?mg/L, contact time of 8?hours, pH value of 4.04. Kinetic studies showed the adsorption followed a pseudo-second-order model and Elovich model. The experimental equilibrium data were fitted Koble-Corrigan model and Freundlich model well and the maximum monolayer adsorption capacity of AC calculated by Langmuir model was 338.58?mg/g at 25?°C. In addition, AC was characterized by the SEM–EDS, BET, FITR and point of zero charge (pH_pzc). The mechanisms of SMS sorption onto AC were explored. Desorption and regeneration tests were carried out to evaluate the feasibility of reusing the AC. This study indicated the AC prepared from SP was an excellent adsorbent with the low cost and high performance.     

A radiotracer study of adsorption on activated carbon cloth from aqueous solution

A study has been made on the effect of pH upon the equilibrium adsorption capacity of triethyl phosphate, dimethyl phosphate and orthophosphate on to activated carbon cloth. It is shown that for molecular phosphates no dependence upon pH exists, whilst the adsorption of ionic phosphates exhibit a strong pH dependence. These adsorption trends may be explained in terms of pKa values, ionic strength and the surface charge of the activated carbon cloth is aqueous solution.     

Adsorption of Cu(II) ions from aqueous solution by hazelnut husk activated carbon prepared with potassium acetate

Hazelnut husk (HH), an agricultural waste, was converted to carbonaceous material by chemical activation using potassium acetate. The produced activated carbon (KAHHAC) was characterized by FTIR, SEM, N₂ adsorption–desorption experiments, CHN elemental analysis, and determination of moisture, ash, and point of zero charge. KAHHAC was used for the batch adsorption of Cu(II) ions from aqueous solutions. Optimum pH and contact time were found to be 5.0 and 240 minutes, respectively. The adsorption equilibrium data were described well by the Langmuir equation providing 105.3?mg?g^?1 Cu(II) adsorption capacity. The pseudo-second-order model successfully described the kinetic of Cu(II) adsorption by KAHHAC. The adsorbed Cu(II) onto KAHHAC was completely desorbed by 0.5?M nitric acid. In conclusion, HH activated carbon (AC) produced by the potassium acetate activation method is a very useful and efficient sorbent material for the removal of Cu(II) from aqueous solution.