空气/水界面2,5-二丙基-4-十一烷基苯磺酸钠的表面动态扩张流变性质

利用悬挂滴方法研究了2,5-二丙基-4-十一烷基苯磺酸钠(3-11-3)在空气/水界面上的动态扩张粘弹性质, 考察了时间、表面压、工作频率及3-11-3的浓度对扩张模量和相角的影响. 研究结果表明, 低表面压条件下, 表面膜以弹性为主, 分子在表面上的状态决定膜性质；高表面压条件下, 分子在体相和表面间的交换过程决定膜性质, 表面膜以粘性为主.     

不同结构芳香侧链酰基牛磺酸钠的表面扩张性质

利用悬挂滴方法研究了N-(α-苯氧基)十四酸牛磺酸钠(12+B-T)和N-(α-对乙基苯氧基)十四酸牛磺酸钠(12+2B-T)在空气/水表面上的动态扩张粘弹性质, 考察了时间、扩张频率及摩尔浓度对扩张模量和相角的影响, 测定了不同摩尔浓度条件下的泡沫性能. 研究发现: 低浓度条件下, 表面分子间相互作用决定表面活性剂吸附膜的性质, 膜以弹性为主; 高浓度条件下, 扩散交换过程起主导作用, 吸附膜表现出粘弹特性. 表面活性剂芳环支链上增加一个乙基, 分子间相互作用增强, 扩张模量增大, 泡沫更加稳定.     

A Surface Rheological Study of Polyoxyethylene Alkyl Ether Carboxylic Salts and the Stability of Corresponding Foam

The dynamic dilational viscoelastic properties of polyoxyethylene alkyl ether carboxylic salts at the air-water interface were investigated by drop shape analysis method and their foam stability were measured by Bikerman Method. The influences of time, dilational frequency, and bulk concentration on surface dilational modulus and phase angle were expounded. The results show that the surfactant with the longest straight-chain shows the highest dilational modulus, which in agreement with the best foam stability. However, the foam stability of branched-alkyl chain surfactant cannot be explained in terms of film elasticity alone.     

Comparison of the Surface Dilational Properties of Block Copolymers and Sodium Oleate Using the Oscillating Bubble Method

The surface dilational modulus of the star-like block copolymer AP432 and linear block copolymer L64 was studied using the oscillating bubble method at an accessible frequency range of 0.05 to 2 Hz, which was compared with anionic surfactant sodium oleate (C₁₇H₃₃COONa) and the influence of inorganic salt NaNO₃ on the surface dilational modulus of AP432 and L64 was also studied. The results indicate that for AP432 and L64 the dilational modulus varies slightly, just decrease gradually with concentrations increasing and never reaches high values with the dilational frequency increasing, but the dilational modulus of C₁₇H₃₃COONa increases gradually with the increase of dilational frequency and pass through the maximum values with increasing concentration. The properties of AP432, L64, and C₁₇H₃₃COONa at the air/water interface were also observed by surface tension measurement. Based on these experimental results, a simple possible adsorption model of these molecules at air/water interface is proposed.     

Dilational Rheological Properties of P-(n-alkyl)-benzyl Polyoxyethylene Ether Carboxybetaine at Water–Decane Interface

The dilational rheological behaviors of absorbed films of p-(n-alkyl)-benzyl polyoxyethylene ether carboxybetaine C_xBE₂CB (x = 8, 10, 12) at the water–decane interface have been investigated by the drop-shape analysis method. The influences of time, oscillation frequency, and bulk concentration on dilational modulus and phase angle have been expounded. The experimental results show that the phase angle of C_xBE₂CB (x = 10, 12) decreases with the increase of time, the slope of the log ? ? log ω curve and phase angle of C_xBE₂CB (x = 10, 12) decrease in a wide concentration range. These phenomena become more and more apparent with the increase of hydrocarbon chain length and it cannot be attributed to the diffusion-exchange process between the bulk and the interface. It is reasonable to consider that ethylene oxide groups are flexible and can be compressed and expanded, just like a spring. Therefore, the compression and expansion of the ethylene oxide groups in the interfacial layer and the exchange between interface and sublayer play a more important role for C_xBE₂CB (x = 10, 12) adsorption film. The dependence of dilational modulus on interfacial pressure can support our provided mechanism strongly.     

Dilational Rheological Properties of Non-Ionic Surfactants at the Water–Decane Interface: Effect of Unsaturated Hydrophobic Group

The interfacial tensions and dilational properties of adsorbed films of two non-ionic surfactants with different hydrophobic groups, polyoxy-ethylene sorbitan stearate (Tween 60) and polyoxy-ethylene sorbitan monooleate (Tween 80), at the water–decane interface have been investigated by the drop-shape analysis method. The effects of dilational frequency and bulk concentration on the interfacial properties were expounded. The influence of low temperature on the interfacial tensions and dilational properties have also been researched. The experiment results show that the interfacial activity of Tween 80 is rather large compared with Tween 60. The minimum area per molecule at the water–decane interface (A_min) value of Tween 80 is little large than that of Tween 60, which is due to the steric effect of unsaturated double bond in Tween 80 molecule. The dilational data show that the ethylene oxide groups of non-ionic surfactant form a stable sub-layer, which results in the increase of modulus and the decrease of phase angle for both Tween 60 and Tween 80 than those of common ionic surfactants. Moreover, the unsaturated hydrophobic group of Tween 80 is much flexible, which is easily crosslinked and entangled. Therefore, dilational modulus of Tween 80 is higher and phase angle is lower than that of Tween 60. Low temperature decreases the flexibility of unsaturated hydrophobic group and lessens the influence on the interaction of saturated hydrophobic group. Saturated surfactant molecules of Tween 60 almost lose temperature response.     

酸性模拟油的油水界面扩张粘弹性研究

考察了不同链长脂肪酸模拟油的扩张模量随扩张频率的变化规律,研究了碱和十二烷基磺酸钠对酸性模拟油界面扩张性质的影响.结果表明,不同脂肪酸模拟油的扩张模量随扩张频率和碳链长度的增加而增大.水相中加入十二烷基磺酸钠对酸性模拟油的扩张模量影响不大,对低工作频率下相角影响较大.无论有无十二烷基磺酸钠,水相中加入NaOH的浓度较低时酸性模拟油的扩张模量变化不大;NaOH浓度较高时,酸性模拟油的界面扩张模量增加,慢弛豫过程在界面上起主要作用,此时界面上可能形成了特殊结构.     

Effect of Alkyl Chain Length on the Interfacial Dilational Properties of Hydroxy-Substituted Alkyl Benzenesulfonates

Dilational rheological behaviors of adsorption layers of three surfactants, sodium 2-hydroxy-3,5-dioctyl benzene sulfonate (C₈C₈), sodium 2-hydroxy-3-octyl-5-decyl benzene sulfonate (C₈C₁₀), and sodium 2-hydroxy-3-octyl-5-dodecylbenzenesulfonate (C₈C₁₂) formed at air–water and decane–water interfaces, have been investigated as a function of concentration and frequency (0.002–0.1 Hz) by the oscillating bubble/drop method. The experimental results show that the dilational moduli of hydroxy-substituted alkyl benzenesulfonates are obviously higher than those of the common surfactants, because the interfacial interactions between alkyl chains are improved drastically by the unique arrangement of C₈C₈ molecules at the interface. However, the moduli at the decane–water interface are much lower than those at the surfaces because decane molecules will insert into the surfactant molecules adsorbed at the interface and destroy the interactions between alkyl chains. With an increase in the number of carbon atom of 5-alkyl, the surface dilational modulus decreases because the orientation of the surfactant molecules at the surface varies from parallel to tilt. On the other hand, the diffusion-exchange process dominates the interfacial behavior and the interfacial modulus improves with the increase in the length of the alkyl chain.     

Effect of Glyphosate Isopropylamine on the Surface Tension and Surface Dilational Rheology Properties of Polyoxyethylene Tallow Amine Surfactant

In order to develop the substitutes for polyoxyethylene tallow amine (POEA), the understanding the interaction of glyphosate isopropylamine and POEA is essential. The surface behaviors of POEA and POEA in the presence of 1 wt% glyphosate isopropylamine have been investigated at the air-water interface by the drop shape analysis method. The influences of surface tension, dilational frequency, and bulk concentration on the surface properties were expounded. The experiment results show that the adsorption films of POEA behave elastic in nature at low bulk concentration. With increasing in bulk concentration, the dilational modulus, dilational elasticity, and dilational viscosity pass through a maximum value, the phase angle increase monotonically. These phenomena can be attributed to the diffusion-exchange process between the bulk and the interface. The addition of 1 wt% glyphosate isopropylamine significantly influences on the POEA surface tension and dilational properties. The dilational modulus, dilational elasticity, and dilational viscosity obvious decrease in general, and the values of phase angle significant change after the addition of 1 wt% glyphosate isopropylamine. Glyphosate isopropylamine and POEA form a new complex in the solution and the surface activity and surface dilational properties of complex is different from POEA.     

表面波技术研究TBP对C12E8表面流变性质的影响

The influence of antifoaming agent TBP on the surface adsorption and on the surface rheological properties of foaming agent C12E8 is investigated by the damped longitudinal wave method, and the antifoaming mechanism of the antifoaming agent TBP on C12E8 is explored in this paper. The experimental results show that while the concentration of foaming agent C12E8 is smaller than cmc and at ω=6.28 rad•s-1, the decreases of surface dilational modulus, surface dilational elasticity, surface dilational viscosity and the increases of the phase angle when the concentration of TBP increase for the C12E8+TBP aqueous solution (C12E8=0.074 mmol•L-1) have been related to the diffusional exchange between surface and bulk and to the Marangoni effect, which depends on the restored mechanism of surface tension gradient due to the stretched surface. This has been related to the mechanism of antifoaming action.     

疏水基支链化对甜菜碱表面扩张流变性质的影响

利用悬挂滴方法研究了同分异构的直链（C₁₆PB）和支链（C₁₆GPB）十六烷基羟丙基羧酸甜菜碱的表面扩张流变性质,考察了时间、表面压、工作频率及体相浓度对扩张模量和相角的影响.研究发现,羟丙基甜菜碱分子在溶液表面上吸附时,整个亲水基团倾向于平铺在表面上,造成较高的表面扩张模量,表面膜性质由亲水基团取向变化等膜内过程控制.甜菜碱分子疏水烷基的支链化造成分子间相互作用增强,不仅能增大模量,而且在高浓度条件下出现动态模量的最大值现象,说明表面膜的强度与分子排布密切相关,并非单纯由表面分子浓度决定.     

Silicon‐modified surfactants and wetting: I. Synthesis of the single components of Silwet L77 and their spreading performance on a low‐energy solid surface

Defined surfactants of general formula [(CH₃)₃SiO]₂CH₃Si(CH₂)₃(OCH₂CH₂)_3–9OCH₃, have been synthesized from the corresponding oligoethylene glycol monoallyl monomethyl ethers via hydrosilylation. The concentration‐dependent spreading performance on hydrophobized silicon wafers has been investigated and compared with that of Silwet L77. For the hexaethylene glycol derivative the highest initial spreading velocities and largest spreading areas were found. Since Silwet L77 spreads faster than all the other derivatives under investigation, a synergistic effect of different compounds is unlikely. Minor differences were found for handshaken and sonicated solutions. Copyright © 1999 John Wiley & Sons, Ltd.     

Interfacial Dilational Properties of Hydrophobically Modified Partly Hydrolyzed Polyacrylamide and Anionic Surfactants at the Water-Decane Interface

The dilational viscoelastic properties of hydrophobically modified partly hydrolyzed polyacrylamide and anionic surfactants (4,5-diheptyl-2-propylbenzene sulfonate and gemini surfactant C₁₂COONa-p-C₉SO₃Na) in the absence or presence of electrolyte have been investigated at the decane–water interface by means of longitudinal method and the interfacial tension relaxation method. Experimental results show that at low surfactant concentration, the increase of the dilational modulus by the addition of surfactant molecules at low frequency might be explained by the mix-adsorption of the polymer chains and surfactant molecules. At the same time, polymer chain could sharply decrease the dilational modulus of surfactant film mainly due to the weakening of the strong interactions among long alkyl chains in surfactant molecules. At high surfactant concentration, the addition of surfactant molecules can decrease the dilational modulus of polymer solution due to the fast process involving in the exchange of surfactant molecules between the interface and the mixed complex formed by surfactant molecules and hydrophobic micro-domains. The added electrolyte, which results in screening of electrostatic interactions between the ionized groups, generally increases the frequency dependence of the interfacial dilational modulus. The data obtained on the relaxation processes via interfacial tension relaxation measurements can explain the results from oscillating barriers measurements very well.     

Silicon‐modified surfactants and wetting: IV. Spreading behaviour of trisiloxane surfactants on energetically different solid surfaces

The spreading behaviour of defined trisiloxane surfactants of general formula [(CH₃)₃SiO]₂ CH₃Si(CH₂)₃(OCH₂CH₂) _nOCH₃ (n = 3–9) on five different solid surfaces has been investigated. Maximum spreading areas and rates are found on non‐polar or slightly polar surfaces of 30 to 40 mN m⁻¹ surface energy. Extremely low or high surface energies substantially reduce the spreading rates. On non‐polar surfaces rapid spreading is observed for 1 wt % solutions of the relatively short‐chained penta‐ and hexa‐ethylene glycol derivatives. On slightly polar surfaces dilute 0.1 wt % solutions of longer‐chained derivatives spread faster. This spreading pattern shift coincides with a change of the phase behaviour. Solutions of Silwet L77 do not prefer one specific surface, since 1 wt % solutions abruptly stop spreading after a few seconds and the maximum spreading rates are found for 0.1 wt % solutions. Therefore, Silwet L77 essentially belongs among the long‐chained derivatives. Copyright © 2000 John Wiley & Sons, Ltd.     

不同结构三取代烷基苯磺酸钠表、界面的扩张性质

利用悬挂滴方法研究了两种同分异构体的表面活性剂2-丙基-4,5-二己基苯磺酸钠(366)和2,5-二丙基-4-壬基苯磺酸钠(393)在空气/水表面和癸烷/水界面上的扩张流变性质, 考察了不同表面活性剂浓度下366和393溶液表、界面扩张性质的异同. 实验结果表明, 磺酸根间位的长链烷基对表面扩张模量贡献较大, 表面活性剂分子大小对界面扩张模量影响较大.     

界面张力弛豫法研究不同结构破乳剂油水界面扩张粘弹性

采用界面张力弛豫法研究了支链破乳剂AE121和直链破乳剂SP169在正癸烷-水界面上的扩张粘弹性质，并与小幅周期振荡法获得的结果进行了比较.阐述了两种破乳剂的扩张模量随扩张频率和破乳剂浓度的变化规律.研究发现，在低频率处，两种破乳剂的扩张模量均接近于零；在中间频率范围内，扩张模量随扩张频率的增加而增大；在高频率处，扩张模量的幅度接近于极限扩张弹性.在中间频率范围内，扩张模量随破乳剂浓度增大，在接近临界胶束浓度处出现一个极大值；同时还发现，界面上和界面附近的微观弛豫过程的数目随破乳剂浓度增加而增大，其贡献也呈规律性变化.     

咪唑基表面活性离子液体在气/液界面的扩张粘弹性

合成了两种咪唑基表面活性离子液体,通过界面膨胀流变法研究了其在气/液界面的聚集行为,考察了咪唑基表面活性离子液体浓度、无机盐和温度对聚集行为的影响。研究发现,咪唑基表面活性离子液体在吸附过程中吸附控制占主导作用,而弛豫过程不是单一指数函数;加入无机盐或升高温度可以提高咪唑基表面活性离子液体的表面活性、增强其在界面的吸附能力、降低表面张力。扩张流变结果显示扩张模量、弹性模量和粘性模量随震荡频率增加而增加;随表面活性离子液体浓度增大,扩张模量先增大后减小。扩张模量随温度升高或无机盐(NaBr或CaBr₂)的加入而降低。表面活性离子液在气/液界面形成的吸附膜以弹性模量为主,而且C₁₄mimBr的界面膜弹性模量大于C₁₂mimBr的界面膜弹性模量。     

Silicon‐modified surfactants and wetting: II. Temperature‐dependent spreading behaviour of oligoethylene glycol derivatives of heptamethyltrisiloxane

The temperature‐dependent spreading performance of defined trisiloxane surfactants of the general formula [(CH₃)₃SiO]₂CH₃Si‐­(CH₂)₃(OCH₂CH₂)_3–9OCH₃ and Silwet L77 on a trimethylsilylated silicon‐wafer surface has been investigated. At 6 °C the tetraethylene glycol derivative showed the highest initial spreading rate. At 40 °C the octaethylene glycol derivative was the fastest spreader. It is shown that spreading behaviour and phase behaviour are closely related. The highest initial spreading rates were found for solutions in the two‐phase state (2Φ) closely above the liquid–liquid insolubility boundary. Copyright © 1999 John Wiley & Sons, Ltd.     

不同结构破乳剂油水界面扩张粘弹性研究

研究了支链破乳剂AE121和直链破乳剂SP169在正癸烷-水界面上的扩张粘弹性质,阐述了两种破乳剂扩张模量随扩张频率和破乳剂浓度的变化规律,考察了两种破乳剂对原油活性组分界面扩张性质的影响,测定了两种破乳剂的水溶液与正癸烷的动态界面张力,并与界面扩张流变性质进行了关联.研究结果表明,两种破乳剂的加入均会大大降低原油活性组分界面膜的扩张模量.较低浓度下直链破乳剂SP169由于吸附能力稍强,降低扩张模量效果较好；而一定浓度以上支链破乳剂AE121由于顶替能力较强,具有一定优势.由于破乳剂本身具有一定的扩张模量,在降低界面扩张模量的效果上,破乳剂的用量并非越大越好.     

Interfacial dilational properties of anionic gemini surfactants with polymethylene spacers

The dilational properties of anionic gemini surfactants alkanediyl-α,ω-bis(m-octylphenoxy sulfonate) (C₈C_mC₈) with polymethylene spacers at the water–air and water–decane interfaces were investigated by oscillating barriers and interfacial tension relaxation methods. The influences of oscillating frequency and bulk concentration on the dilational properties were explored. The experimental results show that the linking spacer plays an important role in the interfacial dilational properties. The moduli pass through one maximum for all three gemini surfactants at both water–air and water–decane interfaces. However, the values of moduli at the water–air interface are obviously higher than those at the water–decane interface because the sublayer formed by spacer chains will be destroyed by the insertion of oil molecules. Moreover, with the increase of spacer length, the surface adsorption film becomes more viscous at high concentration, which can be attributed to the process involving the formation of the sublayer. On the other hand, the spacers of the adsorbed C₈C₆C₈ molecules will extend into the oil phase when the interface is compressed. As a result, the interfacial film becomes more elastic with the increase of spacer length at high concentration. The experimental results obtained by the interfacial tension relaxation measurements are in accord with those obtained by the oscillating barriers method.