光照纳米银颗粒对葡萄糖生物传感器响应电流的抑制

采用纳米银-壳聚糖复合膜固定葡萄糖氧化酶,构建葡萄糖生物传感器.利用计时电流法对不同光照时间纳米银颗粒组装的酶电极响应电流进行了表征.实验结果表明,光照纳米银颗粒可以抑制葡萄糖生物传感器的响应电流;随着光照时间的延长,纳米银颗粒的抑制作用逐渐增强,当光照时间达到120min时,葡萄糖生物传感器的响应电流最小(-3.953μA/cm²).葡萄糖生物传感器响应电流的抑制可能是由纳米银颗粒表面的Ag⁺离子浓度及表面性能的变化引起的.     

Amperometric Glucose Biosensor Based on Ultrafine Platinum Nanoparticles

Abstract

In the present paper the ultrafine and highly dispersed platinum nanoparticles (average size 3 nm) were used for the construction of a glucose biosensor in a simple method. An excellent response to glucose has been obtained with a high sensitivity (137.7 µA mM^?1 cm^?2) and fast response time (5 s). The biosensor showed a detection limit of 5 µM (at the ratio of signal to noise, S/N=3) and a linear range form 0.2 to 3.2 mM with a correlation coefficient r=0.999. The apparent Michaelis–Menten constant (k _m) and the maximum current were estimated to be 9.36 and 1.507 mA mM^?1 cm^?2, respectively. In addition, effects of pH value, applied potential and the interferents on the amperometric response of the sensor were investigated and discussed.     

壳聚糖固定化葡萄糖氧化酶生物传感器测定葡萄糖的含量

应用壳聚糖将葡萄糖氧化酶固定于鸡蛋膜上,结合氧电极制得葡萄糖传感器.实验表明,壳聚糖比戊二醛能更好地固定葡萄糖氧化酶,最佳条件为壳聚糖浓度0.3%、固定化酶量0.8 mg、 pH 7.0、缓冲溶液浓度300 mmol/L和温度25 ℃.本葡萄糖传感器的线性范围为0.016～1.10 mmol/L;检出限为8.0 μmol/L(S/N=3), 响应时间<60 s,有很好的稳定性,寿命>3个月.同一个传感器重复使用以及同方法制作的不同传感器之间都有很好的重现性,RSD分别为2.5%(n=10)和4.7%(n=4).实际样品中可能存在的烟酰胺、 VB6、 VB12、 VE、Ca2+、 Mg2+、 K+和Zn2+等对葡萄糖的测定不产生干扰.本传感器已成功地应用于市售饮料中葡萄糖含量的测定.     

纳米金-还原氧化石墨烯修饰葡萄糖氧化酶传感器的制备及其电流法检测饮料中的葡萄糖

利用纳米金(Au NPs)与还原氧化石墨烯(rGO)复合纳米材料制备了葡萄糖氧化酶生物传感器并用于饮料中葡萄糖含量的检测。将壳聚糖作为还原剂及稳定剂,通过一步法合成了Au NPs-rGO复合材料,并通过物理吸附固定葡萄糖氧化酶(GOx)来制作GOx生物传感器。该传感器在磷酸盐缓冲溶液(0.1 mol/L,p H6.0)中,-0.45 V(vs.Ag/Ag Cl)电位下电流法检测葡萄糖含量,线性检测范围为0.01~0.88 mmol/L,灵敏度为22.54μA·mmol-1·L·cm-2,检出限为1.01μmol/L,且表观米氏常数为0.497 mmol/L。该传感器用于多种饮料中葡萄糖含量的直接检测,结果满意。     

Construction of an Amperometric Glucose Biosensor by Immobilization of Glucose Oxidase on Nanocomposite at the Surface of FTO Electrode

Fluorine? tin oxide (FTO) nanostructure was developed on the surface of a glass plate using spray payroliziz method. A new electrochemical biosensor was fabricated based on a layer by layer process. In this process chitosan? Fe₃O₄ (CH? Fe₃O₄) nanocomposite film was prepared at the surface of FTO electrode by dip? coating method. In the next step, the glucose oxidase (GOx) was immobilized on the CH? Fe₃O₄/FTO nanocomposite electrode. The GOx/CH? Fe₃O₄/FTO bioelectrode has a linear range of 10–270 µM and a detection limit of 5 µM. The highest sensitivity was obtained at 1.2 µA mM^?1 cm^?2.     

一种基于壳聚糖固定葡萄糖氧化酶的葡萄糖生物传感器的研究

本文选用生物相容性好的壳聚糖作为基体材料，使其与戊二醛交联成网状结构包埋葡萄糖氧化酶制成电化学传感器。这种壳聚糖膜不仅可以减小葡萄糖氧化酶的流失，而且能为酶提供了适宜的微环境。用红外光谱、紫外光谱及透射电镜对膜的形态和性质进行了表征。实验结果表明该传感器具有很快的响应速度，很好的稳定性和重现性，能选择性地催化葡萄糖并测定其浓度。该传感器的制备方法简单，成本低，于冰箱中放置两周信号保持在90％以上，对葡萄糖测量的线性范围为1×10^-5 - 3.4×10^-3mol•L^-1，当信噪比为3:1时检测限为5×10^-6mol•L^-1。     

Biosensing Membrane Base on Ferulic Acid and Glucose Oxidase for an Amperometric Glucose Biosensor

A biosensing membrane base on ferulic acid and glucose oxidase is synthesized onto a carbon paste electrode by electropolymerization via cyclic voltammetry in aqueous media at neutral pH at a single step. The developed biosensors exhibit a linear response from 0.082 to 34 mM glucose concentration, with a coefficient of determination R² equal to 0.997. The biosensors display a sensitivity of 1.1 μAmM⁻¹ cm⁻², a detection limit of 0.025 mM, and 0.082 mM as glucose quantification limit. The studies reveal stable, repeatable, and reproducible biosensors response. The results indicate that the novel poly-ferulic acid membrane synthesized by electropolymerization is a promising method for glucose oxidase immobilization towards the development of glucose biosensors. The developed glucose biosensors exhibit a broader linear glucose response than other polymer-based glucose biosensors.     

生物功能电极 III. 葡萄糖氧化酶的电化学固定化研究

利用磷酸盐缓冲溶液中吡咯的电聚合, 将葡萄糖氧化酶(GOD)包埋在聚吡咯(PPy)基质中以构成生物功能电极。讨论了溶液pH和聚合电位对酶固定化的影响, 并用IR和交流阻抗谱对酶膜进行表征。GOD的固定化只有当pH>5.5时才能实现, 由此推测酶是以带负电的粒子嵌入PPy的。交流阻抗谱表明这一电极具有有界多孔电极的特征。探索了酶与电子传递体Fe(CN)_6~(3-)同时固定化的可行性。电化学固定化的GOD保持其生物催化活性, 酶反应表观上遵循Michealis-Menten动力学。     

Immobilization and Characterization of Glucose Oxidase on Single-Walled Carbon Nanotubes and Its Application to Sensing Glucose

The negatively charged （at pH 8.2） glucose oxidase （GOx, pI ca. 4.2） was assembled onto the surface of single-walled carbon nanotubes （SWNT）, which was covered （or wrapped） by a layer of positively charged polyelectrolyte poly（dimethyldiallylammonium chloride） （PDDA）, via the electrostatic interaction forming GOx-PDDASWNT nanocomposites. Fourier transform infrared （FTIR）, UV-Vis and electrochemical impedance spectroscopy （EIS） were used to characterize the growth processes of the nanocomposites. The results indicated that GOx retained its native secondary conformational structure after it was immobilized on the surface of PDDA-SWNT. A biosensor （Nafion-GOx-PDDA-SWNT/GC） was developed by immobilization of GOx-PDDA-SWNT nanocomposites on the surface of glassy carbon （GC） electrode using Nafion （5%） as a binder. The biosensor showed the electrocatalytic activity toward the oxidation of glucose under the presence of ferrocene monocarboxylic acid （FcM） as an electroactive mediator with a good stability, reproducibility and higher biological affinity. Under an optimal condition, the biosensor could be used to detection of glucose, presenting a typical characteristic of Michaelis-Menten kinetics with the apparent Michaelis-Menten constant of KM^app ca. 4.5 mmol/L, with a linear range of the concentration of glucose from 0.5 to 5.5 mmol/L （with correlation coefficient of 0.999） and the detection limit of ca. 83 μmol/L （at a signal-to-noise ratio of 3）. Thus the biosensor was useful in sensing the glucose concentration in serum since the normal glucose concentration in blood serum was around 4.6 mmol/L. The facile procedure of immobilizing GOx used in present work would promote the developments of electrochemical research for enzymes （proteins）, biosensors, biofuel cells and other bioelectrochemical devices.     

利用葡萄糖氧化酶反应体系动力学光度法测定痕量银

基于葡萄糖氧化酶－过氧化物酶－４－氨基安替比林－２，４－二氯苯酚偶联反应的动力学性质及Ａｇ＾＋，Ｈｇ＾２＋，Ａｌ＾３＋，Ｃｕ６２＋等离子对反应的影响，建立了用动力学光度法测定痕量银的新方法。     

固载于壳聚糖-纳米金复合膜修饰玻碳电极上的葡萄糖氧化酶的直接电化学研究及其生物传感应用

通过将葡萄糖氧化酶固载于壳聚糖-纳米金复合膜内所构置的传感器,实现了葡萄糖氧化酶的直接电化学,并采用循环伏安法与电化学阻抗法对修饰电极进行了表征。研究表明：在除氧缓冲溶液中,葡萄糖氧化酶-壳聚糖-纳米金复合膜修饰电极表现出一对良好的氧化还原峰,这对峰归因于葡萄糖氧化酶的氧化还原,证明葡萄糖氧化酶被成功固载于复合膜内。电子传递速率常数为15.6 s-1,说明葡萄糖氧化酶的电活性中心与电极之间的电子传递很快。将壳聚糖与纳米金相结合还提高了葡萄糖氧化酶在复合膜内的稳定性并保持其生物活性,并可以用于葡萄糖检测。计算得到其表观米氏常数为10.1 mmol·L-1。而且,该生物传感器可以用于血样中葡萄糖含量的测定。     

Amperometric Glucose Biosensors Based on Integration of Glucose Oxidase onto Prussian Blue/Carbon Nanotubes Nanocomposite Electrodes

Nanosized Prussian blue (PB) particles were synthesized with a chemical reduction method and then the PB nanoparticles were assembled on the surface of multiwall carbon nanotubes modified glassy carbon electrode (PB/MWNTs/GCE). The results showed that the PB/MWNTs nanocomposite exhibits a remarkably improved catalytic activity towards the reduction of hydrogen peroxide. Glucose oxidase (GOD) was immobilized on the PB/MWNTs platform by an electrochemically polymerized o‐phenylenediamine (OPD) film to construct an amperometric glucose biosensor. The biosensor exhibited a wide linear response up to 8 mM with a low detection limit of 12.7 μM (S/N=3). The Michaelis–Menten constant K_m and the maximum current i_max of the biosensor were 18.0 mM and 4.68 μA, respectively. The selectivity and stability of the biosensor were also investigated.     

纳米金胶增强葡萄糖生物传感器的构建

将纳米金胶(AuNPs)和羟基磷灰石(HAp)按一定比例混合制备了新型复合膜用于葡萄糖氧化酶(GOD)的固定,构建了高灵敏的葡萄糖传感器。由于纳米金胶的存在,葡萄糖氧化酶的直接电化学性质得以增强,在去除氧气的PBS(pH 7.0)介质中,固定在复合膜内的GOD表现出一对良好的氧化还原峰。在饱和氧气条件下,当加入一定量的葡萄糖时,由于GOD催化葡萄糖氧化消耗溶液中的溶解氧,-0.8 V处溶解氧的还原峰电流降低,且峰电流降低的量与葡萄糖浓度在0.02～1.62 mmol/L范围内呈线性相关,检出限为5.0μmol/L,检测灵敏度达9.91 mA.mol-1.L,可实现对葡萄糖的快速检测。     

Electrodeposition of Silver Nanoparticles on MWCNT Film Electrodes for Hydrogen Peroxide Sensing

Silver （Ag） nanoparticles were directly electrodeposited on multi-walled carbon nanotubes （MWCNT） in AgNO3/LiNO3 containing EDTA （ethylenediaminetetraacetic acid）. The structure and nature of the resulting Ag/MWNT composite were characterized by field emission scanning electron microscopy （FE-SEM）, transmission electron microscopy （TEM） and X-ray diffraction （XRD）, and the distribution shape of Ag nanoparticles was found to be dependent on the presence of EDTA. The modified electrode showed excellent electrocatalytic activity to redox reaction of hydrogen peroxide and the mechanism of hydrogen peroxide was partly reversible procession with oxidation and reduction peaks at 0.77 and -0.83 V, respectively. The oxidation and reduction peak currents were linearly related to hydrogen peroxide concentration in the range of 1×10^-6-3×10^-4 and 1 ×10^-8-7× 10^-4 mol·L^-1 with correlation coefficients of 0.996 and 0.986, and 3s-detection limit of 9 × 10^-7 and 7 × 10^-9 mol·L^-1.     

Highly Sensitive and Selective Glucose Biosensing at Carbon Paste Electrodes Modified with Electrogenerated Magnetite Nanoparticles and Glucose Oxidase

This work reports the advantages of carbon paste electrodes modified with electrogenerated magnetite nanoparticles. The nanoparticles present catalytic activity towards hydrogen peroxide reduction. The incorporation of glucose oxidase (GOx) and magnetite in a carbon paste matrix have made possible the development of an efficient glucose biosensor. The effect of the amount of GOx and magnetite present in the composite on the response of the biosensor was critically evaluated. The biosensors demonstrated to be highly selective, with negligible interference of ascorbic acid and uric acid. The proposed biosensor was challenged with human blood serum demonstrating an excellent correlation with the spectrophotometric method.     

Amperometric Glucose Determination by Means of Glucose Oxidase Immobilized on a Cellulose Acetate Film: Dependence on the Immobilization Procedures

Glucose microelectrodes were prepared by immobilizing glucose oxidase onto a cellulose acetate film coating a platinum wire. Hexamethylenediamine (HMDA) and Glutaraldehyde (GA) were employed as spacer and coupling agent, respectively. Sensitivities and linear response ranges were studied as a function of the relative amounts of HMDA and GA. The best sensitivity was found when HMDA and GA were 5% and 2.5% in aqueous solutions, respectively. Taking as a reference the functioning of this biosensor, the roles of HMDA and GA percentages appear to be opposed when the extension of the linear response range is considered. Indeed, an increase of one unit in HMDA percentage (from 5 to 6 %) induces an increase in the extension of the linear response range equal to that obtained with a decrease of one unit of GA percentage (from 2.5 to 1.5%).     

HEC/SiO2凝胶复合物包埋固定化葡萄糖氧化酶的研究

溶胶-凝胶技术;HEC/SiO2凝胶复合物包埋固定化葡萄糖氧化酶的研究     

A Novel Glucose Biosensor Based on Palladium Nanoparticles and Its Application in Detection of Glucose Level in Urine

IntroductionThelevelofglucoseinbloodorurineindicateshyper andhypoglycaemia ,bothofwhichcanresultfromavarietyofendocrinedisorders .1 4 Therapidandreliabledetermi nationofglucoselevelisaroutineprojectinclinicchem istry.Urinesamplesaresaferandmoreconvenientthanbloodones .Meanwhile ,theconcentrationofglucoseinserumiscloselyassociatedwiththatinurine .2 4 Eventhoughglucoseelectrodeshavebeensuccessfullyusedinseruminclinicalapplication ,thequestionstillremainedofhowtodetecttheglucoselevelinurine ,wh…     

Immobilization of Glucose Oxidase on Ordered Macroporous Silicas Functionalized with Amino Group

A novel glucose oxidase immobilized on three‐dimensionally ordered macroporous (3DOM) material has been prepared by firstly preparation of hybrid 3DOM SiO₂‐NH₂ materials using colloidal crystal method, and following covalent immobilization of glucose oxidase on the pore walls of the 3DOM materials. The materials were characterized by SEM, FTIR, DSC and BET techniques. SEM observation shows that the macropores are highly ordered and are interconnected by small windows. FTIR measurement shows that there are amino and organic groups in the pore walls. The surface area of the 3DOM SiO₂‐NH₂ material is about 10.2 m²/g. The loaded amount of enzyme is increased with amino content in the materials. The immobilized enzyme has high activity, thermal stability and can be reused.     

基于碳纳米管和铁氰酸镍纳米颗粒协同作用的葡萄糖生物传感器

将制备的铁氰酸镍纳米颗粒(NiNP)与多壁碳纳米管(CNT)混合, 分散于壳聚糖溶液中, 形成一种新的纳米复合成分(NiNP-CNT-CHIT), 将其修饰在玻碳电极表面. 新复合膜体现了NiNP和CNT之间的协同作用, 由于CNT的良好的传递电子性能, 促使NiNP催化氧化还原能力有了较大的提高. 此NiNP-CNT-CHIT复合膜修饰的玻碳电极在较低电位下对过氧化氢具有良好的电催化性能, 与NiNP-CHIT膜比较, 测定H₂O₂的灵敏度增大了50倍. 通过戊二醛在电极表面固定葡萄糖氧化酶制备了一种新的葡萄糖传感器. 该传感器在－0.2 V下对葡萄糖的线性范围为0.05～10 mmol/L, 检测下限为10 μmol/L.