Synthesis and Properties of Aromatic Side Chained N‐Acyltaurate Surfactants

A series of anionic N‐acyltaurate surfactants, side chain containing aromatic nucleus (abbreviated as SAATT), were synthesized via Williamson reaction, hydrolyzation, and acylation. Krafft temperatures and surface properties of these surfactants at 30°C, that is, critical micelle concentration, cmc, surface excess concentration, Γ_max, surface area demand per molecule, A _min, efficiency in surface tension reduction, pC₂₀, effectiveness in surface tension reduction, π_cmc, and cmc/C₂₀ parameter were determined. It was shown that these surfactants exhibit good solubility which was confirmed by measuring Krafft temperature. The cmc of SAATT was much smaller than that of conventional surfactants with similar effective carbon numbers, and shifted to lower concentration with increasing hydrocarbon chain length. In addition, the γ_cmc decreased with decrease in Γ_max. The pC₂₀ and the cmc/C₂₀ got larger with the increase in hydrocarbon chain length. From the fluorescence intensity ratios of I ₁ (373 nm) and I ₃ (384 nm) using pyrene as a probe, it was indicated that the molecules of SAATT formed loose micelles with a broad size distribution.     

Three-phase contact parameters measurements for silica-mixed cationic–anionic surfactant systems

The stability and interactions in thin wetting films between the silica surface and air bubble containing (a) straight chain C₁₀ amine and (b) cationic/anionic surfactant mixture of a straight chain C₁₀ amine with sodium C₈, C₁₀ and (straight chain) C₁₂ sulfonates, were studied using the microscopic thin wetting film method developed by Platikanov [D. Platikanov, J. Phys. Chem. 68 (1964) 3619]. Film lifetimes, three-phase contact (TPC) expansion rate, receding contact angles and surface tension were measured. The presence of the mixed cationic/anionic surfactants was found to lessen contact angles and suppresses the thin aqueous film rupture, thus inducing longer film lifetime, as compared to the pure amine system. In the case of mixed surfactants heterocoagulation could arise through the formation of positively charged interfacial complexes. Mixed solution of cationic and anionic surfactants shows synergistic lowering in surface tension. The formation of the interfacial complex at the air/solution interface was confirmed by surface tension data. It was also shown, that the chain length compatibility between the anionic and cationic surfactants system controls the strength of the interfacial complex. The observed phenomena were discussed in terms of the electrostatic heterocoagulation theory, where the interactions can be attractive or repulsive depending on the different surface activity and charge of the respective surfactants at the two interfaces.     

Synthesis and properties of double-chain single-head acetamidinium bicarbonate switchable surfactants

A series of switchable surfactants with double hydrophobic chains and a single hydrophilic head N,N’-dialkylacetamidinium bicarbonate with an alkyl length between diC8 and diC12 were synthesized by using new approaches. The structures of acetamidinium bicarbonate were characterized by ^1?H NMR and ESI-MS spectroscopy. The surface activity in aqueous solution of N,N’-dialkylacetamidinium bicarbonate and N’-alkyl-N,N-dimethylacetamidinium were compared by surface tension methods. Some surface activity parameters were studied, such as cmc, γ_cmc, pC₂₀, cmc/C₂₀, Γ_max, and A_min. The results indicated that double-chain surfactant was superior to single-chain surfactant and showed more excellent surface activity. The switchability was confirmed by monitoring the conductivity of a solution of amidine in ethanol and their effect in emulsion stability was also investigated.     

Novel Cationic Gemini Surfactants Based on Piperazine: Synthesis,Surface Activity,and Foam Ability

A series of novel Gemini surfactants C_n-pi-C_n with piperazine moiety as spacer was synthesized and characterized by IR, ¹H NMR, and mass spectra. Their surface activities were evaluated by surface tension, electrical conductivity, and steady-state fluorescence. The obtained results indicated that the synthesized Gemini surfactants exhibited lower critical micelle concentration (cmc) and surface tension (γ_cmc) compared with traditional surfactants. The steady-state fluorescence measurement and electrical conductivity were recorded to demonstrate the accuracy of cmc values. In addition, the micellization was evaluated using conductivity measurement in the temperature range of 298–308 K. The foamability and foam stability of these Gemini surfactants were also examined. In which, the Gemini surfactant with the shortest chain (C₁₂) showed the best foamability but the poorest foam stability. Hydrophile–lipophile balance and emulsifying ability were studied and a comparatively poor emulsifying ability displayed.     

Synthesis and performance of a series of dual hydroxyl sulfobetaine surfactants

Five kinds of dual hydroxyl sulfobetaines with different carbon atom numbers in hydrophobic chain were synthesized by using linear saturated alcohol, epichlorohydrin and dimethylamine, and then their structures were characterized by FTIR and ¹H NMR. The stability of all synthesized betaine surfactants in hard water was at level 4, which indicated they had high tolerance on hard water. Their CMC and γ_cmc were lower than the conventional cationic surfactant dodecyltrimethylammonium bromide and anionic surfactant sodium dodecyl, so they had more excellent surface activities. With the chain length increasing from C₈ to C₁₄, the surface activities, emulsifying properties and foaming properties of these betaine surfactants improved because surfactant molecules tightly arranged in the oil-water interface, but there was abnormal phenomenon of surface activity and foam property from C₁₄ to C₁₆ due to overlong hydrophobic chain. According to the results of the experiment, C₁₄SB was the most practical in the five kinds of surfactants, which was potential candidate to enhance oil recovery in oil field. The performances of C₁₄SB were as follows: CMC?=?2.2?×?10^?4?mol/L, γ_cmc?=?30.9 mN/m and the time of bleeding 10?mL water t?=?375?s at 2?g/L the optimum emulsification concentration.     

Synthesis,surface activity,and corrosion inhibition of dentritic quaternary ammonium salt-type tetrameric surfactants

The dentritic quaternary ammonium salt-type tetrameric surfactant (4C₁₂tetraQ) was synthesized, and the molecular structure was confirmed by ¹H NMR and FTIR. The surface activity of 4C₁₂tetraQ was investigated by surface tension, and surface chemical parameters, such as critical micelle concentration (cmc), efficiency (pC₂₀), effectiveness (π_cmc), the surface tension value at cmc (γ_cmc), minimum surface area (A_min), maximum surface excess (Γ_max), and cmc/C₂₀ were obtained from the measurement results. The results show that the 4C₁₂tetraQ surfactant has higher surface activity than the traditional monomeric surfactants (dodecyl trimethyl ammonium bromide, DTAB). The Krafft points were taken as <0°C, indicating that the synthesized tetrameric surfactants had good water solubility. Free energies of micellization and adsorption show that 4C₁₂tetraQ display greater propensity to absorb at the interface than form micelle in the bulk of the aqueous solution, and that the two processes are spontaneous. The measurement results show that 4C₁₂tetraQ has good emulsification power and foam performance. The corrosion efficiency was evaluated with the loss weight method in 1?mol/L HCl solution, and the results show that the 4C₁₂tetraQ surfactant has good corrosion inhibition, and can be considered as a corrosion inhibitor.     

双子型阴离子表面活性剂的合成及浮选性能

分别以辛酰氯、癸酰氯、十二酰氯为原料,经加成、酰化及皂化等反应合成了3种双子型阴离子表面活性剂。产物结构经IR、1HNMR和13CNMR等波谱测试技术确定。25℃时测定了表面活性参数,结果表明随分子中疏水链增长,临界胶束浓度及表面张力均降低。目标化合物能一定程度增强油酸对胶磷矿中白云石的浮选能力。     

Interfacial and Thermodynamic Properties of Anionic‐Nonionic Mixed Surfactant System: Influence of Hydrophobic Chain Length of the Nonionic Surfactant

The influence of hydrophobic chain length in nonionic surfactants on interfacial and thermodynamics properties of a binary anionic‐nonionic mixed surfactant was investigated. In this study, nonionic surfactants lauric‐monoethanolamide (C₁₂ MEA) and myrisitic‐monoethanolamide (C₁₄ MEA) were mixed with an anionic surfactant, α‐olefin sulfonate (AOS). The critical micelle concentration (cmc), maximum surface excess (Γ_max), and minimum area per molecule (A_min) were obtained from surface tension isotherms at various temperatures. The thermodynamic parameters of micellization and adsorption were also computed. Micellar aggregation number (N_agg), micropolarity, and binding constant (K_sv) of pure and mixed surfactant system was calculated by fluorescence measurements. Rubingh's method was applied to calculate interaction parameters for the mixed surfactant systems.     

Interfacial and aggregation properties of some anionic/cationic surfactant binary systems II. Mixed micelle formation and surface tension reduction effectiveness

Mixed micelle formation and surface tension reduction effectiveness (γ_cmc) were investigated for the following systems: triethanolammonium dodecylpoly(oxyethylene)sulfate (TADPS, containing about two ethylene oxide units)/dodecyltrimethylammonium bromide, TADPS/hexadecyltrimethylammonium bromide and TADPS/hexadecylpyridinium chloride. For all these anionic/cationic systems, the mixed critical micelle concentration (cmc) values reflect a strong synergism in mixed micelle formation, with β^M values ranging from −13.8 to −18.3. The mixed micelle composition is mixing-ratio dependent and, for equimolar mixtures, the mixed micelle is richer in the surfactant with the lower cmc. Precipitation is inhibited to a certain extent, thanks to the presence of ethylene oxide groups in the anionic species. The conditions for synergism in γ_cmc, differently expressed in the literature, can be derived from the surface tension equations established in our previous article. They can be conveniently described by a few characteristic constants: Γ _i ^∞ (saturated Gibbs excess), K _i (constant in the Szyszkowski equation), the cmc of the individual surfactants and the interaction parameters, β^S and β^M, of their mixtures. Excellent agreement between theoretically predicted and experimental results is obtained. With the increase in surfactant chain length, the β^M values decrease faster than the β^S ones and this can result in the loss of synergism in γ_cmc. Received: 11 June 2000 Accepted: 4 September 2000     

The influence of mixed cationic–anionic surfactants on the three-phase contact parameters in silica–solution systems

The formation of thin wetting films on silica surface from aqueous solution of (a) tetradecyltrimetilammonium bromide (C₁₄TAB) and (b) surfactant mixture of the cationic C₁₄TAB with the anionic sodium alkyl- (straight chain C₁₂–, C₁₄– and C₁₆–) sulfonates, was studied using the microscopic thin wetting film method developed by Platikanov. Film lifetimes, three-phase contact (TPC) expansion rates, receding contact angles and surface tension were measured. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetimes, as compared to the pure C₁₄TAB. This behavior was explained by the strong initial adsorption of interfacial complexes from the mixed surfactant system at the air/solution interface, followed by adsorption at the silica interface. The formation of the interfacial complexes at the air/solution interface was proved by means of the surface tension data. It was also shown, that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex and causes synergistic lowering in the surface tension. The film rupture mechanism was explained by the heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface, which remained negatively charged.     

The physicochemical properties of aqueous mixtures of cationic-anionic surfactants: I. The effect of chain length symmetry

The solution behaviors of equimolar mixtures of cationic-anionic surfactants have been studied by means of the dynamic light scattering technique and surface tension measurements. The surface activity and the micellization properties are different for systems of different hydrophobic chain length symmetry. For systems of lower symmetry (e.g., C₆H₁₃NC₅H₅Br-C₁₂H₂₅SO₄Na mixture), the surface tension at cmc (γ_cmc) is rather high (above 30 mN m⁻¹) and the mixtures form genuinely homogeneous micellar solutions above the cmc. For the systems of high symmetry (e.g., C₈H₁₇NC₅H₅Br-C₈H₁₇SO₄Na mixture), γ_cmc is very low (about 24 mN m⁻¹, near the value of pure hydrocarbon) and in the apparently homogeneous and clear mixtures slightly above cmc, the aggregates grow slowly and eventually form small droplets; as the concentration is further increased, all these solutions become turbid. We have proposed a new concept of conformation energy of aggregates to account for all these phenomena. Mixtures of octyltriethylammonium bromide and sodium octylsulfate form clear homogeneous micellar solutions in keeping with predictions based upon this concept.     

Adsorption and thermodynamic properties of dissymmetric gemini imidazolium surfactants with different spacer length

A series of dissymmetric gemini imidazolium surfactants with different spacer length ([C_mC_sC_nim]Br₂, m + n = 24, m = 12, 14, 16, 18; s = 2, 4, 6) were synthesized and characterized by ¹H NMR and ESI-MS spectroscopy. Their adsorption and thermodynamic properties were investigated by the surface tension and electrical conductivity methods. Consequently, the surface activity parameters (cmc, γ_cmc, π_cmc, pC₂₀, cmc/C₂₀, Γ_max, A_min) and thermodynamic parameters (ΔG_m^θ, ΔH_m^θ, ΔS_m^θ) were obtained. The effects of the dissymmetry (m/n) and the spacer length (s) on the surface activity and micellization process of surfactants have been discussed in detail.     

Studies of Synthesis and Interfacial Properties of Sodium Branched‐Alkylbenzenesulfonates

Two sodium branched‐alkylbenzensulfonates with additional alkyl substituents were synthesized through a series of reactions. The interfacial tension of these alkylbenzenesulfonates between 1.0% NaCl solution and six n‐alkanes were measured. From the data of measurements the following values were calculated: critical micelle concentration (cmc), the interfacial tension at the cmc (γ_cmc), interfacial excess concentration at the cmc (Γ_m), area per molecule at the cmc (A_m). There were a minimum γ_cmc and a maximum Γ_m appeared for the same n‐alkane with increasing the hydrocarbon chain length of the oil. These indicated that the hydrocarbon chain length of oil have the important effect on adsorption and interfacial tension.     

Effect of Organic Solvents on the Electrodeposition of Copper from Acidified CuSO4

Using Guerbet tetradecyl alcohol C₁₄GA (synthesized by Guerbet reaction using 1-heptanol as raw material) as intermediate, sodium Guerbet tetradecyl polyoxyethylene ether sulfates [C₁₄GA(EO)_nS, n = 1, 2, 4] were obtained through following steps: synthesizing Guerbet tetradecyl polyoxyethylene ether alcohols [C₁₄GA(EO)_nH, n = 1, 2, 4] by Williamson reaction, then esterifying with chlorosulfonic acid so as to form Guerbet tetradecyl polyoxyethylene ether alcohol sulfates [C₁₄GA(EO)_nSO₃H, n = 1, 2, 4], and finally neutralizing with sodium hydroxide; while sodium Guerbet tetradecyl sulfate(C₁₄GAS) was synthesized only through esterifying and neutralizing reactions. The structures of these anionic surfactants were determined by infrared, nuclear magnetic resonance, and element analysis. The surface activity of these surfactants was studied by means of surface tension. The results have shown that these surfactants possess higher surface activity than the common surfactant C₁₂H₂₅OSO₃Na. Branched-tail structure coming from Guerbet alcohol makes the anionic surfactant (C₁₄GAS) have higher critical micelle concentration (CMC) and better effectiveness in lowering the interface tension between air and water than their linear counterpart (C₁₄H₂₉OSO₃Na). Introducing oxyethyene group into the place between head group and tail group of the surfactant molecule with branched tail can lower the CMC, γ_cmc, and Krafft point. And the effectiveness for reducing the CMC, γ_cmc, Γ_max, and Krafft point of surfactant increased with the increase of oxyethylene group number (n = 1, 2, 4). The relationship between the molecular structure and surface activity of surfactant is discussed.     

Surface and interfacial properties of 1,3-dialkyl glyceryl ether hydroxypropyl sulfonates as surfactants for enhanced oil recovery

A series of double-chain anionic surfactants, 1,3-dialkyl glyceryl ether hydroxylpropyl sulfonates (diC_mGE-HS, m?=?8, 10, 12), were synthesized from renewable materials. These surfactants possess very low γ_cmc (～25?mN/m) at 25°C, and their mixtures with conventional surfactants can reduce Daqing crude oil/connate water IFT to ultralow at 45°C in wide total concentration range (0.625-10?mM) in the presence of 0.5?wt.% Na₂CO₃. It seems that diC₁₂GE-HS behaves as a hydrophobic component, whereas diC₁₀GE-HS and diC₈GE-HS behave as hydrophilic components in these mixtures. The mixtures also exhibit high resistance against adsorption by sandstone and good ability of keeping sandstone surface water-wet.     

Synthesis,micellization properties,and cytotoxicity trends of N-hydroxyethyl-3-alkyloxypyridinium surfactants

N-hydroxyethyl-3-alkyloxypyridinium amphiphiles have been synthesized and characterized by various spectroscopic techniques. Self-assembling properties of these amphiphiles have been studied by surface tension, conductivity, and fluorescence measurements. Basic micellization parameters like critical micelle concentration (cmc), surface tension at the cmc (γ _cmc), adsorption efficiency (pC₂₀), effectiveness of surface tension reduction (Π _cmc), maximum surface excess concentration (Γ _max) and minimum surface area/molecule (A _min), and Gibbs free energy of the micellization (ΔG⁰ _mic) have also been determined. The micellization of these 3-alkyloxypyridinium halides in aqueous phase have been found to be exothermic and entropy-driven as assessed by conductivity measurements at different temperatures. Thermal degradation of these surfactants has also been assessed by thermal gravimetric analysis under nitrogen atmosphere. Further, 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay of these surfactants on C6 glioma cells show them to be less toxic than conventional cationic surfactants.     

Synthesis and Surface Properties of Novel Cationic Gemini Surfactants

A series of novel cationic gemini surfactants, p-[C _n H_2n+1N⁺(CH₃)₂CH₂CH(OH)CH₂O]₂C₆H₄·2Cl^? [A(n = 12), B(n = 14) and C(n = 16)], containing a spacer group with two flexible and hydrophilic groups (2-hydroxy-1,3-propylene) on both sides of a rigid and hydrophobic group (1,4-dioxyphenylene) has been synthesized by the reaction of hydroquinone diglycidyl ether with N,N-dimethylalkylamine and N,N-dimethylalkylamine hydrochloride. Their surface-active properties have been investigated by surface tension measurement. The critical micelle concentration (cmc) values of the synthesized cationic gemini surfactants are one order of magnitude lower than those of their corresponding monomeric surfactants (C _n H_2n + 1N⁺(CH₃)₃·Cl^?). Both the cmc and surface tension at the cmc (γ_cmc) of A are lower than those of p-[C₁₂H₂₅N⁺(CH₃)₂CH₂]₂C₆H₄·2Cl^? (D). The novel cationic gemini surfactants A and B also show good foaming properties.     

Synthesis and surface activity of novel glucose ester surfactants containing carbohydrate and hydrocarbon chain

A series of glucosyl esters surfactants were synthesized based on glucose molecule by enzymatic catalysis. It could reach the highest esterification yield of 83.4% at the optimal condition, molar ratio of D-glucose and fatty acyl amino acid as 3:2 using 11% (w/w) enzyme catalyst Lipozyme 435 as catalyst in t-butanol at 40°C. The surface activities were studied, such as the critical micelle concentration (CMC), surface tension (γ_cmc), maximum excess concentration (Γ_max), minimum surface area/molecule (A_min), and the adsorption efficiency (pC₂₀); values of these were obtained by surface tension test. The results show that the longer the hydrophobic chain length, the lower the CMC and γ_cmc. The CMCs of novel glucosyl esters were between 4.4 and 1.5 mM. Further, the micellization physiochemical parameters, including Gibbs free energy of micellization (ΔG), standard enthalpy change (ΔH), and standard entropy change (ΔS) were calculated. It was indicated the micellization of glucosyl esters 9–16 was driven by entropy and deduced at different temperature.     

Alkylpolyglycoside: Carbohydrate Based Surfactant

Carbohydrates are growing important renewable raw material for surfactant industry. The development of surfactants based on carbohydrate and vegetable oils is the result of the product concept based on the exclusive use of natural resources. Sugar based surfactants are gaining increased attention due to advantage with regard to performance, health of consumer and environmental compatibility compared to some standard product.

Alkylpolyglycoside (APG) is nonionic surfactant prepared from renewable raw materials namely glucose and fatty alcohol. Such products are expected to exhibit surface‐active properties due to the presence of the hydrophilic sugar moiety and the hydrophobic fatty alcohol residues. This article deals with the synthesis of alkylpolyglycoside and the study their surface active properties.

APG was prepared by using fatty alcohol varying in chain length from C8‐C18.

Effect of alkyl chain length of APG on the basic characteristics such as surface tension, interfacial tension, lime soap dispersing power, detergency, foaming, and wetting were studied.

Alkylpolyglycoside prepared from octanol, decanol, and dodecanol are water soluble and shows good surface active properties where as those prepared from long chain fatty alcohols were water insoluble and, therefore, not evaluated for their surface active properties. Incorporation of APG in toilet soap was studied.