Mechanism of Produced Gas Reinjection During CO2 Flooding by Chromatographic Analysis

CO₂ flooding process has been a proven valuable method that could not only enhance oil recovery but also store greenhouse gas. However, CO₂ source greatly restrict its application in China. In this article, based on the produced oil and gas of Jilin oilfield, slim tube tests were conducted to study the feasibility of the produced gas reinjection without separation. In addition, according to the phenomenon of the experiment, displacement process was divided into three stages. Chromatographic analysis was conducted to study the mechanism of production gas reinjection during CO₂. Results indicate that components of the produced oil change along with CO₂ content, displacement pressure and production stages.     

Nanofluid in Hydrophilic State for EOR Implication Through Carbonate Reservoir

More than 50% of oil is trapped in petroleum reservoirs after applying primary and secondary recovery methods for removal. Thus, to produce more crude oils from these reservoirs, different enhanced oil recovery (EOR) approaches should be performed. In this research, the effect of hydrophilic nanoparticles of SiO₂ at 12 nm size, in (EOR) from carbonate reservoir is systematically investigated. Using this nanoparticle, we can increase viscosity of the injection fluid and then lower the mobility ratio between oil and nanofluid in carbonate reservoirs. To this end, a core flooding apparatus was used to determine the effectiveness and robustness of nanosilica for EOR from carbonate reservoirs. These experiments are applied on the reservoir carbonate core samples, which are saturated with brine and oil that was injected with nanoparticles of SiO₂ at various concentrations. The output results depict that, with increasing nanoparticle concentration, the viscosity of the injection fluid increases and results in decreased mobility ratio between oil and nanofluid. The results confirm that using the nanoparticle increases the recovery. Also, increasing the nanoparticle concentration up to 0.6% increases the ultimate recovery (%OOIP), but a further increase to 1.0 does not have a significant effect.     

Determination of Minimum Miscibility Pressure of CO2–Oil System: A Molecular Dynamics Study

CO₂ enhanced oil recovery (CO₂-EOR) has become significantly crucial to the petroleum industry, in particular, CO₂ miscible flooding can greatly improve the efficiency of EOR. Minimum miscibility pressure (MMP) is a vital factor affecting CO₂ flooding, which determines the yield and economic benefit of oil recovery. Therefore, it is important to predict this property for a successful field development plan. In this study, a novel model based on molecular dynamics to determine MMP was developed. The model characterized a miscible state by calculating the ratio of CO₂ and crude oil atoms that pass through the initial interface. The whole process was not affected by other external objective factors. We compared our model with several famous empirical correlations, and obtained satisfactory results—the relative errors were 8.53% and 13.71% for the two equations derived from our model. Furthermore, we found the MMPs predicted by different reference materials (i.e., CO₂/crude oil) were approximately linear (R² = 0.955). We also confirmed the linear relationship between MMP and reservoir temperature (T_R). The correlation coefficient was about 0.15 MPa/K in the present study.     

Foam Flooding with Ultra-Low Interfacial Tension to Enhance Heavy Oil Recovery

Severe viscous fingering during water flooding of heavy oil leaves a large amount of oil untouched in the reservoir. Improving sweep efficiency is vital for increasing heavy oil recovery. Previous researches have proved that foam flooding can increase the sweep efficiency and oil recovery. The polymers could make the foam more stable and have better plugging capacity, but the interfacial tension (IFT) of oil and water increase which could decrease the displacement efficiency of the heavy oil. In view of the deficiency of conventional foam flooding, it is necessary to research the ultra-low interfacial tension foam which could improve macro-swept volume and micro-displacement efficiency in heavy oil reservoir. In this paper a novel foam agent is developed by the combination of surfactant and additives to lower the IFT of oil and water. The operating parameters including foam injections modes and gas liquid ratio were investigated by core flooding experiments. Field test performance shows that oil production per day increased from 85.6 to 125.7 t, water cut declined from 92.1 to 83.6% after 3 months injection. This study provides a novel method to improve heavy oil recovery with an ultra-low interfacial tension foam flooding system.     

Nonequilibrium Features of N2 and Oil System

Nonequilibrium state is a universal phenomenon in gas injection development. However, in previous researches and applications, it tends to be regarded as quasi-equilibrium state, or even equilibrium state. Based on research work by pioneers, a simple model for measuring diffusivity of N₂ in oil has been developed. In addition, laboratory experiments were performed in this study. Results indicate that an infinitely thin layer exists between N₂ zone and oil zone in the pressure-volume-temperaturacelda (PVT) cell. Gas and oil molecules will slowly diffuse into one another across the sharp interface by convection, dispersion, and diffusion. Viscosity and gas oil ratio (GOR) are two important parameters representing the phase behavior features of the N₂ and oil system. These dependent variables are related to parameters like pressure, temperature, and oil viscosity.     

Application of CO2-Triggered Switchable Surfactants to Form Emulsion with Xinjiang Heavy Oil

Owing to the high acid number of Xinjiang heavy oil and incomplete demulsification after pipelining, this article discusses the application of CO₂-triggered switchable surfactants to the emulsified transport of several Xinjiang heavy oils in the pipeline. Results show that CO₂-triggered switchable surfactants promote the formation and stabilization of oil-in-water (O/W) emulsion in the absence of CO₂ as a base. The property parameters of heavy oils fundamentally influence the indigenous emulsifying agents. The emulsion is stable when the heavy oil has a high acid number and low asphaltene content, which is also affected by some physical factors.     

Improvement of Sweep Efficiency by Alkaline Flooding for Heavy Oil Reservoirs

Severe viscous fingering during water flooding of heavy oil leaves a large amount of oil untouched in the reservoir. Improving sweep efficiency is vital for enhancing heavy oil recovery. This study presented a laboratory study for improving sweep efficiency by alkaline flooding in heavy oil Reservoirs. This included glass-etched micromodel flooding tests, one-dimensional flooding experiments and three-dimensional physical model study. The micromodel tests show that W/O droplet flow plays a prominent role in the alkaline flooding to improve sweep efficiency. There is a minimum alkaline concentration that generates the W/O droplet flow, and the W/O droplet flow is more obvious with the alkaline concentration increasing. A series of flood tests were conducted using 325 mPa · s, 2000 mPa · s, and 3950 mPa · s heavy oils to assess the effectiveness of W/O droplet flow in alkaline flooding for enhanced heavy oil recovery. The flood tests results demonstrate the considerable potential for improved heavy oil recovery by alkaline flooding, and moreover, the incremental oil recovery has been found to increase as the alkaline concentration increases. The result obtained in three-dimensional physical model study indicates that the sweep area can be greatly improved by the formation of W/O droplet flow in alkaline flooding.     

Characterization of Remaining Oil After Polymer Flooding by Laser Scanning Confocal Fluorescence Microscopy

In the mid- to late period of oil field development, it is important to consider the microscopic distribution of remaining oil of the reservoir in time, for it is the foundation of enhanced oil recovery. Focusing on the present insufficient research status of microscopic distribution of remaining oil after polymer flooding, this article first put forward and developed a set of fluorescence microscope technology of frozen core analysis of remaining oil, and used this technology combined with laser confocal microscopic detection technology to study microscopic distribution rules of remaining oil before and after polymer flooding. Through comparison and analysis on the difference of microscopic distribution form of remaining oil, the experimental results show that polymer flooding has different effects on different types of remaining oil. Using this technology, analysis of many different distribution forms of remaining oil involving the same mode of occurrence in different layers, different parts of the same layer, and different types of the same layer can be more clearly distinguished. Using polymer flooding pertinently according to the different distribution form of remaining oil will make the use of polymer more efficiently and the recovery higher.     

The Wettability Alteration and the Effect of Initial Rock Wettability on Oil Recovery in Surfactant-based Enhanced Oil Recovery Processes

Wettablity alteration of rock surface is an important mechanism for surfactant-based enhanced oil recovery (EOR) processes. Two salt and temperature-tolerant surfactant formulations were developed based on the conditions of high temperature (97–120°C) and high salinity (20 × 10⁴ mg/L) reservoirs where a surfactant-based EOR process is attempted. Both the two sufactant formulations can achieve ultralow interfacial tension level (≤10^?3 mN/m) with crude oil after aging for 125 days at reservoir conditions. Wettability alteration of core slices induced by the two surfactant formulations was evalutated by measuring contact angles. Core flooding experiments were carried out to study the influence of initial rock wettabilities on oil recovery in the crude oil/surfactant/formation water/rock system. The results indicated that the two formulations could turn oil-wet core slices into water-wet at 90–120°C and 20 × 10⁴ mg/L salinity, while the water-wet core slices retained their hydrophilic nature. The core flooding experiments showed that the water-wet cores could yield higher oil recovery compared with the oil-wet cores in water flooding, surfactant, and subsequent water flooding process. The two surfactant formulations could successfully yield additional oil recovery in both oil-wet and water-wet cores.     

Four Methods to Estimate Minimum Miscibility Pressure of CO2‐Oil Based on Machine Learning

CO₂ flooding accounts for a considerable proportion in gas flooding. Using CO₂ as a gas displacement agent is benefit for enhanced oil recovery (EOR), and the alleviation of the greenhouse effect by the permanent storage of CO₂ in the crust. Minimum miscibility pressure (MMP) of CO₂‐oil is a key factor affecting EOR, which determines the yield and economic benefit of crude oil recovery. Therefore, it is of great importance to use fast, accurate and cheap prediction methods for MMP estimation. In the present study, to evaluate the reliability of four recently developed prediction models based on machine learning (i.e., neural network analysis (NNA), genetic function approximation (GFA), multiple linear regression (MLR), partial least squares (PLS)), 136 sets of data are selected for calculation via outlier analysis from 147 sets of data. Afterwards, we compared the four models with existing prediction models from the literature. The analysis of correlation coefficients and multiple error functions shows that the four models can solve the MMP prediction problem well, and the model using intelligent algorithm has a higher prediction accuracy than the simple linear model. Besides, intelligent methods based on similarity algorithm have little difference from each other. Finally, a sensitivity analysis was conducted.     

Laboratory Study on Low Gas/Liquid Ratio Foam Flooding for Zhuangxi Heavy Oil

Considering the high cost and injection pressure of conventional foam flooding, foam flooding with low gas/liquid ratio was proposed to enhance the heavy oil recovery. A foamer containing 0.2 wt% α -olefin sulfonate, 0.1 wt% HPAM and 0.5 wt% Na₂CO₃ was selected for Zhuangxi heavy oil. Then the foam stability and low gas/liquid ratio foam flooding were studied via micro model and sand pack experiments. The results indicate that the foam is much more stable in heavy oil than in diesel; in flooding tests, this foamer with gas/liquid ratio of 0.2:1 increases the oil recovery by 39.8%, which is nearly 11% higher than ASP solution in terms of the same injection volume (0.3PV) and agents.     

Mechanistic Simulation Studies on Viscous-Elastic Polymer Flooding in Petroleum Reservoirs

Based on the theory and application developments of polymer flooding on enhancing oil recovery, an improved mathematical model has been developed to simulate the mechanism of viscous-elastic polymer flooding. IMPES method has been presented to solve the polymer flooding model considering the viscosifying effect of elasticity, the effect of decreasing residual oil and the degradation of polymer molecules. The validation of the model is approved by an experiment. A simulation example was carried out using the developed numerical simulator. The enhanced oil recovery mechanism was discussed for viscous-elastic polymer flooding, and corresponding influencing factors were also studied.     

Hydrophobically Associating Polymers Dissolved in Seawater for Enhanced Oil Recovery of Bohai Offshore Oilfields

As compared to China’s overall oil reserves, the reserve share of offshore oilfields is rather significant. However, offshore oilfield circumstances for enhanced oil recovery (EOR) include not just severe temperatures and salinity, but also restricted space on offshore platforms. This harsh oil production environment requires polymers with relatively strong salt resistance, solubility, thickening ability, rapid, superior injection capabilities, and anti-shearing ability. As a result, research into polymers with high viscosity and quick solubility is recognized as critical to meeting the criteria of polymer flooding in offshore oil reservoirs. For the above purposes, a novel hydrophobically associating polymer (HAP) was prepared to be used for polymer flooding of Bohai offshore oilfields. The synthetic procedure was free radical polymerization in aqueous solutions starting at 0 °C, using acrylamide (AM), acrylic acid (AA), 2-acrylamido-2-methylpropane sulfonic acid (AMPS), and poly(ethylene glycol) octadecyl methacrylate (POM) as comonomers. It was discovered that under ideal conditions, the molecular weight of HAP exceeds 2.1 × 10⁷ g⋅mol⁻¹. In a simulated reservoir environment, HAP has substantially greater solubility, thickening property, and salt resistance than conventional polyacrylamide (HPAM), with equivalent molecular weight. Finally, the injectivity and propagation of the two polymers in porous media were investigated. Compared with HPAM, which has a similar molecular weight, HAP solution with the concentration of 0.175% had a much better oil displacement effect in the porous medium, which can enhance oil recovery by 8.8%. These discoveries have the potential to pave the way for chemical EOR in offshore oilfields.     

Oil-CO2 MMP Determination in Competition of Neural Network,Support Vector Regression,and Committee Machine

Oil-CO₂ minimum miscible pressure (MMP) has significance in selecting appropriate reservoir for miscible gas injection and greatly governs performance of local displacement. Accurate determination of MMP is very expensive, time-consuming, and labor intensive. Therefore, the quest for a method to determine MMP accurately and save time and money is necessary. This study held a competition between neural network and support vector regression models and assessed their performance in prediction of MMP for both pure and impure miscible CO₂ injection. Subsequently, a committee machine was constructed based on divide and conquer principle to reap benefits of both model and increases the precision of final prediction. Results indicated committee machine performed more satisfyingly compared with individual intelligent models performing alone.      

Soybean-Oil-Based CO2-Switchable Surfactants with Multiple Heads

Oligomeric surfactants display the novel properties of low surface activity, low critical micellar concentration and enhanced viscosity, but no CO₂ switchable oligomeric surfactants have been developed so far. The introduction of CO₂ can convert tertiary amine reversibly to quaternary ammonium salt, which causes switchable surface activity. In this study, epoxidized soybean oil was selected as a raw material to synthesize a CO₂-responsive oligomeric surfactant. After addition and removal of CO₂, the conductivity analyzing proves that the oligomeric surfactant had a good response to CO₂ stimulation. The viscosity of the oligomeric surfactant solution increased obviously after sparging CO₂, but returned to its initial low viscosity in the absence of CO₂. This work is expected to open a new window for the study of bio-based CO₂-stimulated oligomeric surfactants.     

Experimental study on high-pressure rheology of water/crude oil emulsion in the presence of methane

The crude oil is in most cases accompanied with water and natural gas. For this reason, it is important to understand the rheology of the oil emulsion. There are already many works relating to rheology of the oil/water emulsion. However, studies on high-pressure rheology of water/crude oil emulsion in the presence of CH₄ are rare. In this work, light crude oil with characteristics of high wax content, which is typical in Northwest China, was studied. The rheology of water/crude oil emulsion in the presence of CH₄ under various conditions were fully studied. The results show that the crude oil emulsion showed obvious characteristics of non-Newtonian fluid at a lower temperature. Before water fraction reached a certain limit, the viscosity increases with the increase of water fraction, when water fraction reaches and exceeds the limit the emulsion viscosity drops with the increase of water fraction. The shear stress–shear rate curves become similar as the increase of temperature, indicating the decreasing effect of temperature on the relation between shear stress and shear rate. When the pressure reaches 8 MPa, the shear stress measured with CH₄ in the system surpasses that measured without CH₄. At higher pressure, CH₄ shows obvious influence on the rheology.     

Application of CO2-Switchable Oleic-Acid-Based Surfactant for Reducing Viscosity of Heavy Oil

CO₂-switchable oligomeric surfactants have good viscosity-reducing properties; however, the complex synthesis of surfactants limits their application. In this study, a CO₂-switchable “pseudo”-tetrameric surfactant oleic acid (OA)/cyclic polyamine (cyclen) was prepared by simple mixing and subsequently used to reduce the viscosity of heavy oil. The surface activity of OA/cyclen was explored by a surface tensiometer and a potential for viscosity reduction was revealed. The CO₂ switchability of OA/cyclen was investigated by alternately introducing CO₂ and N₂, and OA/cyclen was confirmed to exhibit a reversible CO₂-switching performance. The emulsification and viscosity reduction analyses elucidated that a molar ratio of OA/cyclen of 4:1 formed the “pseudo”-tetrameric surfactants, and the emulsions of water and heavy oil with OA/cyclen have good stability and low viscosity and can be destabilized quickly by introducing CO₂. The findings reported in this study reveal that it is feasible to prepare CO₂-switchable pseudo-tetrameric surfactants with viscosity-reducing properties by simple mixing, thus providing a pathway for the emulsification and demulsification of heavy oil by using the CO₂-switchable “pseudo”-oligomeric surfactants.     

Experimental Investigation on Yield Stress of Water-in-Heavy Crude Oil Emulsions in Order to Improve Pipeline Flow

An experimental study on yield stress of water-in-heavy crude oil emulsions has been carried out by using a HAAKE RS6000 Rheometer with a vane-type rotor. Several factors such as oil volume fraction, shear rate, temperature, and emulsifying agent on the yield stress of emulsions were investigated. Zero shear viscosity of heavy crude oil was 6000 mPas at 30°C, with a density 955 kg/m³. This study shows that the yield stress increases linearly with the increasing shear rate, and displays an exponential decay with increasing the temperature and oil volume fraction. Although the addition of emulsifying agent enhanced the stability of the emulsion, to some extent it also increased the yield stress, especially for the emulsions with high oil volume fractions. Therefore, to reduce the start-up force for the pipeline transport of water-in-heavy crude oil emulsions, the starting rate should be decreased, temperature increased, or oil volume fraction increased. These results are helpful to improve the transportation of water-in-heavy crude oil in pipeline.      

CO2 Mobility and CO2/Brine Interfacial Tension Reduction by Using a New Surfactant for EOR Applications

The synthesis and use in enhanced oil recovery applications of a novel CO₂-philic surfactant derived from maleic anhydride and 2-butyl-1-octanol is reported. The synthesis involved the esterification of maleic anhydride to produce diester followed by sulfonation of the esterified product. The esterification reaction parameters were optimized for the maximum yield of 98.4%. By employing a silica sulfuric acid catalyst, the reaction kinetics of esterification were also investigated. The activation energy was found to be 45.58 kJ/mol. The sulfonation reaction of the esterified product was performed by using sodium bisulfite, and a yield of 82% of surfactant was achieved. The synthesized surfactant lowered the interfacial tension between CO₂/brine to 3.1 mN/m and effectively reduced the CO₂ mobility. This surfactant has a great potential to be used for CO₂ mobility control for CO₂?EOR applications.