On the nature of decrease in the particles size of nanostructured nickel oxide obtained by the sol-gel method in the presence of surfactants

A processes of formation of nanostructured powders of nickel oxide by annealing in the temperature range of 200–700°C of the nickel hydroxide obtained by the sol-gel method at 80°C from solutions of nickel nitrate by precipitation with alkali in the presence of surfactant AF-12 (polyethylene oxide alkylphenyl ether) was investigated. The formation of nanostructured powders of nickel oxide in the presence of a surfactant reduces the size of nanoparticles to 20–25 nm, which is 1.5 times smaller than the particles obtained without a surfactant. The effective influence of surfactant on the particle size begins in the temperature range of its decomposition and evaporation equal 350–400°C.     

A model for surfactant distribution in latex coatings

The presence of surfactants in dried latex films can adversely affect the adhesive, water-resistant, and gloss properties, so investigating the surfactant distribution in latex coatings is of prime industrial relevance. Here we present a model that predicts the distribution of surfactant in a latex coating during the solvent evaporation stage. The conservation equation for surfactant during solvent evaporation is solved in the limit of infinite particle Peclet numbers, a dimensionless quantity giving the measure of relative magnitudes of evaporative to diffusive fluxes. A parametric analysis using the model reveals that the surfactant adsorption isotherm is the determining physical parameter. The model always predicts surfactant excesses at the top surface and either excess or depletion at the bottom surface depending on the isotherm. Uniform distributions are predicted for low surfactant Peclet numbers. Attenuated total reflection Fourier transform infrared spectroscopic probes on film surfaces conform to the behavior predicted by the model.     

Simultaneous spreading and evaporation: Recent developments

The recent progress in theoretical and experimental studies of simultaneous spreading and evaporation of liquid droplets on solid substrates is discussed for pure liquids including nanodroplets, nanosuspensions of inorganic particles (nanofluids) and surfactant solutions. Evaporation of both complete wetting and partial wetting liquids into a nonsaturated vapour atmosphere are considered. However, the main attention is paid to the case of partial wetting when the hysteresis of static contact angle takes place. In the case of complete wetting the spreading/evaporation process proceeds in two stages. A theory was suggested for this case and a good agreement with available experimental data was achieved. In the case of partial wetting the spreading/evaporation of a sessile droplet of pure liquid goes through four subsequent stages: (i) the initial stage, spreading, is relatively short (1–2 min) and therefore evaporation can be neglected during this stage; during the initial stage the contact angle reaches the value of advancing contact angle and the radius of the droplet base reaches its maximum value, (ii) the first stage of evaporation is characterised by the constant value of the radius of the droplet base; the value of the contact angle during the first stage decreases from static advancing to static receding contact angle; (iii) during the second stage of evaporation the contact angle remains constant and equal to its receding value, while the radius of the droplet base decreases; and (iv) at the third stage of evaporation both the contact angle and the radius of the droplet base decrease until the drop completely disappears. It has been shown theoretically and confirmed experimentally that during the first and second stages of evaporation the volume of droplet to power 2/3 decreases linearly with time. The universal dependence of the contact angle during the first stage and of the radius of the droplet base during the second stage on the reduced time has been derived theoretically and confirmed experimentally. The theory developed for pure liquids is applicable also to nanofluids, where a good agreement with the available experimental data has been found. However, in the case of evaporation of surfactant solutions the process deviates from the theoretical predictions for pure liquids at concentration below critical wetting concentration and is in agreement with the theoretical predictions at concentrations above it.     

Ionically self-assembled carboxymethyl cellulose/surfactant complexes for antistatic paper coatings

We show that ionically self-assembled polyelectrolyte/surfactant complexes allow a facile route to tailor the electrical surface resistance of paper sheets for antistatic dissipative regime. We use anionic polyelectrolyte carboxymethyl cellulose (CMC) where cationic alkyltrimethylammonium chloride surfactants (C(n)TAC) with the alkyl chain lengths n=12, 14 or 16 methyl units are ionically complexed by precipitation from aqueous solutions. Such alkyl chains are sufficiently long to allow self-assembly in solid films after solvent evaporation. Short chain lengths, e.g., n=8, did not lead to precipitation. Small angle X-ray scattering indicates cylindrical self-assembly in bulk samples. Upon exposing bulk samples under humidity of 50% RH for 18 h, conductivity of ca. 10(-5) S/cm at room temperature is achieved based on AC-impedance analysis. Flexographic printing and spray coating were selected to conceptually test the feasibility as paper coatings and surface sheet resistances of ca. 10(9) Omega are reached. The results indicate that self-assembled polyelectrolyte/surfactant complexes can allow sufficient conductivity levels for antistatic paper coatings potentially due to protonic conductivity and suggest to develop processes and materials for realistic applications.     

Effect of nonionic surfactant on wetting behavior of an evaporating drop under a reduced pressure environment

The evaporation of sessile drops at reduced pressure is investigated. The evaporation of water droplets on aluminum and PTFE surfaces at reduced pressure was compared. It was found that water droplets on an aluminum surface exhibit a 'depinning jump' at subatmospheric pressures. This is when a pinned droplet suddenly depins, with an increase in contact angle and a simultaneous decrease in the base width. The evaporation of sessile water droplets with a nonionic surfactant (Triton X-100) added to an aluminum surface was then studied. The initial contact angle exhibited a minimum at 0.001 wt% Triton X-100. A maximum in the evaporation rate was also observed at the same concentration. Droplets with low surfactant concentrations are found to exhibit the 'depinning jump.' It is thought that the local concentration of the surfactant causes a gradient of surface tension. The balance at the contact angle is dictated by complex phenomena, including surfactant diffusion and adsorption processes at interfaces. Due to the strong evaporation near the triple line, an accumulation of the surfactant will lead to a surface tension gradient along the interface. The gradient of surface tension will influence the wetting behavior (Marangoni effect). At low surfactant concentrations the contact line depins under the strong effect of surface tension gradient that develops spontaneously over the droplet interface due to surfactant accumulation near the triple line. The maximum evaporation rate corresponds to a minimum contact angle for a pinned droplet.     

The pH-Dependent Surface Activity of a Hydrocarbon/Fluorocarbon Catanionic Surfactant for Water/Hydrofluoroether Microemulsions: The Characterization of a New Acid/Soap Complex

The pH sensitivity of a hydrocarbon/fluorocarbon catanionic surfactant is investigated. The catanionic surfactant is sensitive to low pH, which results in the precipitation of an acid/soap complex. This complex is identified by IR, NMR and confirmed by x-ray crystallography.     

表面活性剂的基体辅助激光解吸电离/质谱分析表征

利用基体辅助激光解吸电离／质谱（MALDI－MS）技术对表面活性剂的分析表征进行了详细研究。以2，5－二羟基苯甲酸作为基体，考察MALDI样品制备方法如液滴干燥法、快速干燥法及三明治法对测定结果的影响，发现三明治方法更适合表面活性剂的分析。MALDI可以准确测定离子型表面活性剂的分子量，同时对于非离子型表面活性剂，还可以测定其平均聚合度和分子量的分布。     

Difference in Surface Properties between Insoluble Monolayer and Adsorbed Film from Kinetics of Water Evaporation and BAM Image

The evaporation rate of water molecules across three kinds of interfaces (air/water interface (1), air/surfactant solution interface (2), and air/water interface covered by insoluble monolayer (3)) was examined using a remodeled thermogravimetric balance. There was no difference in both the evaporation rate and the activation energy for the first two interfaces for three types of surfactant solutions below and above the critical micelle concentration (cmc). This means that the molecular surface area from the Gibbs surface excess has nothing to do with the evaporation rate. In the third case, the insoluble monolayer of 1-heptadecanol decreased the evaporation rate and increased the activation energy, indicating a clear difference between an insoluble monolayer and an adsorbed film of soluble surfactant. This difference was substantiated by BAM images, too. The images of three surfactant solution interfaces were similar to that of just the water surface, while distinct structures of molecular assemblies were observed for the insoluble monolayer. The concentration profile of water molecules in an air/liquid interfacial region was derived by Fix's second law. The profile indicates that a definite layer just beneath the air/liquid interface of the surfactant solution is made mostly of water molecules and that the layer thickness is a few times the root-mean-square displacement %@mt;sys@%%@rl;;@%2%@ital@%Dt%@rsf@%%@rlx@%%@mx@% of the water molecules. The thickness was found to be more than a few nanometers, as estimated from several relaxation times derived from the other kinetics than evaporation of amphiphilic molecules in aqueous systems and a maximum evaporation rate of purified water.     

Thermal stability of aDesulfovibrio gigas periplasmic hydrogenase in reverse micelles

The thermal and operational stabilities ofDesulfovibrio gigas periplasmic hydrogenase were studied at 30 and 50°C in aqueous and micellar media. At the lower temperature the hydrogenase was more stable in reverse micelles of a cationic surfactant. No inactivation was detected over almost 16 d of incubation of the hydrogenase in the reverse micellar solution, during which the enzyme lost around 50% of the initial enzymatic activity in the aqueous solution. At 50°C the hydrogenase was more stable in aqueous medium, because of the changes that occur with the temperature in the organic phase—precipitation of surfactant and solvent evaporation. It was found that only micellar solutions of this enzyme can be repeatedly used, since the hydrogenase is inactivated after the first cycle of oxireduction in aqueous medium. The effect of glycerol and the electron carrier methylviologen as stabilizers of hydrogenase activity was also investigated. The results are interpreted on the grounds of hydrogenase and surfactant electrostatic properties.     

Preparation and characterisation of Na2S and ZnSO4 nanoparticles in water/sodium bis(2-ethylhexyl)sulphosuccinate/n-heptane microemulsions

The preparation procedure for nanoparticles of the water-soluble salts Na₂S and ZnSO₄, two commonly used reagents to synthesise ZnS nanoparticles, by evaporation of volatile components of salt-containing water-in-oil microemulsions is described. In suitable conditions, the evaporation leads to the formation of dry salt–surfactant composites and to the formation of Na₂S or ZnSO₄ nanoparticles. It was found that the salt–surfactant composites can be totally redissolved in a dry apolar organic solvent allowing the formation of virtually water-free solutions containing a considerable amount of the water-soluble salts. The presence of nanoparticles in these solutions and in the composites has been proved by small-angle X-ray scattering and transmission electron microscopy, respectively. By mixing these solutions, the solid–solid reaction between Na₂S and ZnSO₄ nanoparticles leading to the formation of very small-sized ZnS nanoparticles has been ascertained by UV spectrophotometry. Received: 09 February 2001 Accepted: 19 March 2001     

Effect of 1-hexanol on the phase behavior of SDS/CTAB/NaBr/H2O system

Abstract

The influence of 1-hexanol on the phase behavior of sodium dodecyl sulfate (SDS)/cetyltrimethyl ammonium bromide (CTAB)/NaBr/H₂O system has been systematically investigated in this paper. The results showed 1-hexanol effectively dissolved the precipitate formed by the CTAB and SDS surfactants, while liquid crystal (LC) and aqueous two phase system (ATPS) were formed in a wider range. When the molar ratio of 1-hexanol to surfactant is higher than 1, the precipitation in the system disappeared completely and was transformed into ATPS and LC, indicating that alcohol inserted at least evenly between every two surfactant molecules and hence effectively weakened the electrostatic interaction between the anionic and cationic surfactants and limited the formation of precipitation. Polarizing microscope (POM) with crossed polarizers was employed to investigate the textures of liquid crystals. It was shown that the existence of lamellar LC was confirmed by “Maltese crosses” textures. Additionally, we showed that the thermal stability of LC was promising. The ATPS and LC regions remained stable and changed slightly when the temperature was increased from 40 to 70?°C. The results indicated that ATPS and LC of the system were quiet resistant to temperature with the addition of 1-hexanol.     

Tailoring of the external and internal morphology of poly-3-hydroxy butyrate microparticles

Some microencapsulation procedures such as oil-in-water (o/w) and water-in-oil-in-water (w/o/w) emulsions were selected in an attempt to produce tailored poly-3-hydroxybutyrate (PHB) microparticles. The effects of several processing parameters such as polymer precipitation, surfactant, solvent, stirring and solvent evaporation rates were also considered. As a rule, low stirring rates at 500 rpm yielded particles ranging between 100 to 250 μm and at rates over 8000 rpm, diameters around 5–10 μm. The surfaces of the bigger particles, observed by scanning electron microscopy (SEM), were rough and the smaller ones were even rougher, irregular, cauliflower like. The extraction of the chloroform under low pressure or to the open atmosphere did not produce any appreciable change in the morphology for either type of particle. Transmission electron microscopy (TEM) micrographs suggest that microparticles obtained by o/w emulsions are monolithics but those obtained by w/o/w emulsions are of capsule-like structure. Microencapsulation of a peptide material such as follicle stimulating hormone was carried out with success using a double emulsion technique. This biomaterial, dissolved in the inner aqueous phase, was able to stabilize the primary emulsion without using a surfactant.     

Evaporation rate from aerosol OT-water-n-heptane inverse micellar systems

The evaporation rate of aerosol OT-water-n-heptane inverse micellar systems was studied. The evaporation behavior of solutions was strongly affected when compared with pure heptane. The changes are related to the structure of the micelles and the properties of the water molecules dissolved in the micelles. The initial rate of evaporation reaches a maximum when the surfactant head groups are hydrated with three water molecules, a minimum when the first hydration shell of Na⁺ ions is completed, and then rises and stabilizes until the second hydration shell is completed. The presence of free water when the ratio water molecules to surfactant molecules exceeds 12 produces a new rise of the initial evaporation rate, which is always higher than that of puren-heptane.     

Original Preparation of PEKK Dispersion for Coating by Transfer from a Chloroform Stable Dispersion to an Aqueous Stable Dispersion,by Emulsion/Solvent Evaporation

In this work, aqueous dispersions of PolyEtherKetoneKetone (PEKK) oligomers were obtained by an emulsion/dispersion solvent evaporation technique. The PEKK oligomers were synthesized by a Friedel–Crafts acylation with a number average degree of polymerization of 4. The synthesized PEKK oligomers had very good thermal stability and spontaneously formed a stable dispersion of swollen micrometric fibers in chloroform. After sonication of the chloroform dispersion in water in the presence of sodium dodecyl sulfate (SDS) and evaporation, we obtained aggregated particles with a mean diameter between 120 and 160 nm, decreasing linearly with the PEKK concentration. The most stable dispersions were obtained with 0.5% wt of surfactant and, at a fixed concentration of SDS, the stability decreased when the PEKK concentration was increased. The different dispersions of PEKK in water were very stable and, after water evaporation, formed homogeneous films for high-performance coating.     

Formation and structural heat-stability of β-lactoglobulin/surfactant complexes

The binding of two model surfactants, sodium dodecyl sulfate and dodecyltrimethylammonium bromide to β-lactoglobulin was studied at room temperature and the thermal stability of the resulting complexes was evaluated by differential scanning calorimetry (DSC) measurements. Binding isotherms indicated both ionic and hydrophobic interactions depending on both the charge of the protein and surfactant at different pHs and on the binding molar ratios of surfactant to the globular protein. Zeta potential measurements indicated charge neutralisation of the protein, under suitable conditions, which also lead to aggregation and precipitation of the proteins. Surface tension measurements indicated similarity between the two types of oppositely charged protein-surfactant complexes and a difference between them when protein and surfactants are similarly charged. DSC measurements revealed different behavior in protein conformation in the presence of the two surfactants. The results obtained at room temperature and upon heating are discussed in terms of the nature of the surfactant/protein interactions involved in the complex formation.     

Surfactant self-assembling in gas phase: electrospray ionization- and matrix-assisted laser desorption/ionization-mass spectrometry of singly charged AOT clusters

The self-assembling of sodium bis (2-ethylhexyl) sulfosuccinate (AOT) in gas phase has been investigated by electrospray ionization- and matrix-assisted laser desorption/ionization mass spectrometry. Large surfactant clusters with an aggregation number close to that found in apolar media have been observed either as positive or negative ions. Moreover, the marked predominance of singly charged species as well as preliminary theoretical calculations strongly suggest an aggregate structure characterized by an internal hydrophilic core hosting the extra charge surrounded by an apolar shell constituted by the surfactant alkyl chains. This structure is similar to that of the more familiar reversed micelles formed when an appropriate surfactant is solubilized in apolar solvents. Finally, similar trends are observed independently either on the ionization technique or the polarity of the solvent used. This, together with the large dependence of the aggregation number on the flow rates, strongly indicates that self-assembling of the surfactant molecules occurs during the evaporation step.     

表面活性剂辅助合成LiNi0.8Co0.1Mn0.1O2正极材料

通过添加烷基季铵盐类表面活性剂来调控材料形貌和粒径的改性方法,在LiNi_0.8Co_0.1Mn_0.1O₂前驱体合成过程中添加表面活性剂十二烷基三甲基溴化铵(DTAB)和十六烷基三甲基溴化铵(CTAB),利用尿素作为配合剂和沉淀剂,采用溶剂热法合成LiNi_0.8Co_0.1Mn_0.1O₂前驱体。最后,高温混锂煅烧合成椭球形的空心多孔材料。相比于不添加表面活性剂的样本,改性的材料有着更小的粒径和更加规整的形貌。电化学测试表明,添加DTAB和CTAB之后,首次充电容量分别达到223与251 mAh·g^-1(0.1C)。其中,添加CTAB的样品首次放电容量达到216 mAh·g^-1(0.1C),100次循环后容量保持率为85.1%,高于LiNi_0.8Co_0.1Mn_0.1O₂的81.7%(0.1C)。表面活性剂的改性显著提高了材料的电化学性能,为高镍三元正极材料的改性提供了一种新的思路。     

Spreading, evaporation, and contact line dynamics of surfactant-laden microdrops

An optical technique based on the reflectivity measurements of a thin film was used to experimentally study the spreading, evaporation, contact line motion, and thin film characteristics of drops consisting of a water-surfactant (polyalkyleneoxide-modified heptamethyltrisiloxane, called superspreader) solution on a fused silica surface. On the basis of the experimental observations, we concluded that the surfactant adsorbs primarily at the solid-liquid and liquid-vapor interfaces near the contact line region. At equilibrium, the completely wetting corner meniscus was associated with a flat adsorbed film having a thickness of approximately 31 nm. The calculated Hamaker constant, A = -4.47 x 10(-)(20) J, shows that this thin film was stable under equilibrium conditions. During a subsequent evaporation/condensation phase-change process, the thin film of the surfactant solution was unstable, and it broke into microdrops having a finite contact angle. The thickness of the adsorbed film associated with the drops was lower than that of the equilibrium meniscus. The drop profiles were experimentally measured and analyzed during the phase-change process as the contact line advanced and receded. The apparent contact angle, the maximum concave curvature near the contact line region, and the convex curvature of the drop increased as the drop grew during condensation, whereas these quantities decreased during evaporation. The position of the maximum concave curvature of the drop moved toward the center of the drop during condensation, whereas it moved away from the center during evaporation. The contact line velocity was correlated to the observed experimental results and was compared with the results of the drops of a pure alcohol. The experimentally obtained thickness profiles, contact angle profiles, and curvature profiles of the drops explain how the surfactant adsorption affects the contact line motion. We found that there was an abrupt change in the velocity of the contact line when the adsorbed film of the surfactant solution was just hydrated or desiccated during the phase-change processes. This result shows the effect of vesicles and aggregates of the surfactant on the shape evolution of the drops. For these surfactant-laden water drops, we found that the apparent contact angle increased during condensation and decreased during evaporation. However, for the drop of a pure liquid (n-butanol and 2-propanol) the apparent contact angle remained constant at a constant velocity during condensation and evaporation. The contact line was pinned during the evaporation and spreading of the surfactant-laden water drops, but it was not pinned for a drop of a pure alcohol (self-similar shape evolution).     

Surfactive water-soluble copolymers for the preparation of controlled surface nanoparticles by double emulsion/solvent evaporation

We have already shown that polylactide (PLA) nanoparticles covered with a hydrophilic polymeric layer can be prepared by simple emulsion/solvent evaporation by using amphiphilic copolymers as surfactants during the procedure. The external layer is then constituted by the hydrophilic part of the macromolecular surfactant. This kind of nanospheres is useful for the encapsulation of lipohilic molecules. The use of amphiphilic copolymers as surfactants in the preparation of PLA nanospheres with controlled surface properties, was then applied to the double emulsion/solvent evaporation procedure. The aim was to allow the encapsulation of water-soluble bioactive molecules in PLA particles with controlled surface properties. In this paper, we describe the results obtained with three different water-soluble monomethoxypolyethylene oxide (MPEO)-b-PLA diblock copolymers used as surfactants in the preparation of nanoparticles by double emulsion/solvent evaporation. After organic solvent evaporation, the obtained nanospheres were proved to be really covered by a MPEO layer whose characteristics were determined. It was firstly shown that the MPEO-covered particles did not flocculate at 25 degrees C, even in 4 M NaCl while suspensions of bare nanospheres were destabilized for a NaCl concentration as low as 0.04 M. On the other hand, the suspensions of MPEO-covered nanoparticles in 0.3 M Na2SO4 were found to be very sensitive to temperature as they flocculated at a temperature lying between 45 and 55 degrees C depending on the MPEO-b-PLA composition. This property was attributed to the fact that MPEO is a polymer with a low critical solution temperature. The concentration of MPEO at the nanoparticle surface was then calculated for the three kinds of particles, from the initial flocculation temperature, and was found to be comparable to the value determined directly.     

Adsorption of oppositely charged polyelectrolyte/surfactant complexes at the air/water interface: formation of interfacial gels

The adsorption and complexation of polystyrene sulfonate (a highly charged anionic polyelectrolyte) and dodecyltrimethylammonium bromide (a cationic surfactant) at the air-water interface can lead to interfacial gels that strongly influence foam-film drainage and stability. The formation and characteristics of these gels have been studied by combining surface tension, ellipsometry, and foam-film drainage experiments. Simultaneously, the solution electromotive force is measured and used to track the polymer-surfactant interactions in the bulk solution. We find that surface gelation occurs above the critical aggregation concentration in solution but before bulk precipitation of the polymer-surfactant complexes. Furthermore, we reveal that strong readsorption of polymer-surfactant complexes occurs during the resolubilization of the precipitated complexes at high surfactant concentrations (i.e., >critical micelle concentration). Seemingly overlooked in the past, this readsorption significantly influences the surface rheological properties and foam-film drainage of these systems.