One-dimensional and two-dimensional liquid chromatography of sulphonated lignins

One- and two-dimensional separation methods have been developed for the analysis of lignosulphonates and sulphonated kraft lignins. The evaluated sulphonated lignins are all used as dispersants in agrochemical formulations, where some give rise to physical instabilities of formulations. It is of interest to identify the properties of the sulphonated lignins that determine the formulation characteristics. Tetrapentylammonium bromide has been used as an ion-pair reagent in a gradient-elution reversed-phase liquid-chromatographic (IP-RPLC) method, as well as in aqueous size-exclusion chromatography (SEC). Clear differences in the size distribution were observed between different batches of sulphonated lignins. The RPLC and SEC methods were combined in a comprehensive two-dimensional liquid chromatography system. The retention times in the two dimensions were highly correlated. Therefore, the full potential of comprehensive two-dimensional liquid chromatography was not yet realized. However, the results did reveal that retention in IP-RPLC was not determined by the degree of sulphonation of similar-size molecules. Rather, molecules were separated according to size and the degree of sulphonation appears to be approximately constant. The information obtained in this study represents a significant step towards meaningful correlations between the requirements of surfactants within an agrochemical formulation and structural parameters, such as the size and the degree of sulphonation of lignin oligomers.     

Fourier transform infrared spectroscopic determination of cypermethrin and deltamethrin in emulsifiable concentrate formulations

Fourier tranform infrared (FT-IR) spectroscopic method has been developed for determination of cypermethrin and deltamethrin in emulsifiable concentrate formulations. The known concentration of formulation was subjected to preparative thin layer chromatography and the active ingradient zone was scrapped from the plate. Pyrethroids were eluted from the adsorbent with chloroform and estimated by measuring the ester carbonyl absorption band at 1749 cm(-1) in cypermethrin and at 1743 cm(-1) in deltamethrin using base line technique. Recoveries of cypermethrin and deltamethrin from commercial and laboratory prepared formulations were 90 to 97% in both the cases. The validity of FT-IR method was confirmed by comparing the results with standard HPLC method.     

Zirconia Supported on Rice Husk Silica from Biowaste: A Novel,Efficient, and Recoverable Nanocatalyst for the Green Synthesis of Tetrahydro-1-benzopyrans

Russian Journal of Organic Chemistry - Zirconia supported silica from rice husk (an agricultural waste) has been utilized as a novel and efficient heterogeneous catalyst for the synthesis of...     

Studies on potential utilization of rice husk char in blend with lignite for cocombustion application

Combustion behavior of Indian lignite sample blended with rice husk chars (prepared at low temperature) has been examined in this study through simultaneous differential scanning calorimetry (DSC) and thermogravimetric analysis (TG) technique. Range of inputs obtainable by characteristic TG–DSC parameters has been utilized to arrive at important conclusions and observations in respect of ideal selection of blend proportion, proper utilization of the blend combination, etc. Deviations of experimental mass loss pattern (TG) and of rate curve (DTG) from corresponding expected theoretically calculated pattern have also been noted for different blends to examine possible advantageous or disadvantageous effects. As per the observations recorded, use of biomass char in blends (with lignite) was found to be very much beneficial and its proportion in the blends may be restricted to a level of 40 % by mass to extract maximum benefits in burning performance. This paper also focuses specific advantages of use of rice husk char in place of raw rice husk for cocombustion applications. Moreover, the importance of heat release pattern to assess compatibility of a fuel mix with existing boiler design and also to workout fresh boiler design for cocombustion application has been discussed in this paper.     

Polymer Micro‐ and Nanocapsules as Biological Carriers with Multifunctional Properties

The design and development of multifunctional polymer capsules with controlled chemical composition and physical properties has been the focus of academic and industrial research in recent years. Especially in the biomedical field, the formulation of novel polymer‐based encapsulation systems for the early‐stage disease diagnostic and effective delivery of bioactive agents represent one of the most rapidly advancing areas of science. The stimuli‐responsive release of cargo molecules from the carrier gains remarkable attention for in vitro and in vivo delivery of contrast agents, genes, and pharmaceutics. In this Review, the current status and the challenges of different polymer‐based micro‐ and nanocapsule formulations are considered, emphasizing on their potential biological application as carriers for specific drug targeting and controlled release upon applying of external stimulus.     

Synthesis,Characterization, and Catalytic Behavior of Bamboo Rice Husk Ash

In this paper, we report the use of bamboo rice husk ash as an efficient, greener, reusable, and biodegradable heterogeneous catalyst for the synthesis of tetrahydro‐4H ‐chromene‐3‐carbonitriles via the one‐pot three‐component reaction of malononitrile with aromatic aldehydes and dimedone or 1,3‐cyclohexanedione. The formation of bamboo rice husk ash‐silica has been confirmed by several analytical techniques.     

Influence of particle design on oral absorption of poorly water-soluble drug in a silica particle-supercritical fluid system

The physicochemical characteristics and oral absorption of a poorly water-soluble drug, K-832, adsorbed onto porous silica (Sylysia 350), were compared with those of K-832 adsorbed onto non-porous silica (Aerosil 200). K-832 and silica were treated with supercritical CO(2) (scCO(2)) to produce K-832-Sylysia 350 and K-832-Aerosil 200 formulations. Scanning electron microscopy, polarizing microscopy, powder X-ray diffraction, and differential scanning calorimetry results suggested that K-832 mainly existed in an amorphous state in both formulations. The specific surface area of both formulations was much larger than that of pure K-832 crystals. The dissolution rate of K-832 from both formulations was considerably greater than that from corresponding physical mixtures due to rapid wetting of the hydrophilic carrier surfaces and amorphous state, the dissolution from the K-832-Sylysia 350 formulation being the fastest. In vivo absorption tests on the two formulations indicated no significant differences in their peak concentration (C(max)) and the area under their plasma concentration-time curve (AUC), while the concentrations of K-832 in the K-832-Sylysia 350 formulation were significantly higher than those in the K-832-Aerosil 200 formulation 1 h and 1.5 h after administration of these formulations (p<0.05). This could be attributed to the different dispersion states of K-832 in the formulations due to their different three-dimensional structures (porous and non-porous). In physical stability tests, the amorphous drugs in both formulations were stable at room temperature for at least 14 months. Thus, the absorption of poorly water-soluble drugs could be greatly improved by adsorption onto porous silica using scCO(2).     

端羟基聚丁二烯/增塑剂共混物相容性的分子动力学模拟

固体推进剂和炸药的力学性能在很大程度上依赖于配方中高分子粘结剂与增塑剂的相容性. 本文对相容和非相容两种体系进行了分子动力学(MD)模拟, 以考察分子模拟方法的实用性. 为预测固体推进剂中端羟基聚丁二烯(HTPB)与增塑剂癸二酸二辛酯(DOS)、硝化甘油(NG)的相容性, 采用MD模拟方法在COMPASS力场下, 对HTPB、DOS、NG和共混物HTPB/DOS、HTPB/NG的密度、内聚能密度及溶度参数等进行了模拟计算. 通过比较溶度参数差值(△δ)的大小、分子间径向分布函数和模拟前后体系密度变化情况均可以预测HTPB/DOS属于相容体系,而HTPB/NG属于不相容体系, 与实验结果一致. 径向分布函数分析同时揭示了HTPB/增塑剂组分之间的相互作用及本质. 本文的模拟方法可以作为预测聚合物与增塑剂相容性的有利工具, 也可以为固体推进剂和炸药的配方设计提供理论指导.     

Study of the Effect of the Interaction Between Kaolin and Surfactant Blend (AOS: APG C12) on the Solubility,Dispersibility, and Wetting Property of the Pesticide Granule

The extensive use of pesticides in agriculture in particular herbicides is a serious environmental threat. There is an urgent need to develop pesticide formulation that combines optimum bioactivity and minimum dosage. In the present article an attempt has been made to design granular formulation of one of the most commonly used herbicide, atrazine (AT). This potent herbicide along with kaolin as the carrier and suitable clay modifiers can be thought as one of the potential way of formulation keeping in view the desired dosage and bioavailability of the same. The process of granule formulation was carried out using the principle of rapid mix granulation. These granule formulations were then compared with the other formulation where the clay was not modified with the help of parameters such as dissolution rate, dispersion stability and wetting time. The study reveals a very positive effect of clay modifications on granules in terms of above mentioned quality parameters.     

Removal of Reactofix Navy Blue 2 GFN from aqueous solutions using adsorption techniques

The wheat husk, an agricultural by-product, has been activated and used as an adsorbent for the adsorption of Reactofix Navy Blue 2 GFN from aqueous solution. In this work, adsorption of Reactofix Navy Blue 2 GFN on wheat husk and charcoal has been studied by using batch studies. The equilibrium adsorption level was determined to be a function of the solution pH, adsorbent dosage, dye concentration and contact time. The equilibrium adsorption capacities of wheat husk and charcoal for dye removal were obtained using Freundlich and Langmuir isotherms. Thermodynamic parameters such as the free energies, enthalpies and entropies of adsorption were also evaluated. Adsorption process is considered suitable for removing color, COD from waste water.     

Characterization of rice husks and the products of its thermal degradation in air or nitrogen atmosphere

Rice husk is a by-product of rice milling process and are a major waste product of the agricultural industry. They have now become a great source as a raw biomass material for manufacturing value-added silicon composite products, including silicon carbide, silicon nitride, silicon tetrachloride, pure silicon, zeolite, fillers of rubber and plastic composites, adsorbent and support of catalysts. The bulk and true densities of raw rice husk with different moisture and sizes were determined. The rice husk was subjected to pyrolysis in fluidized-bed reactor in air or nitrogen atmosphere. The products obtained were characterized by thermogravimetric and X-ray powder analysis, IR-spectroscopy, scanning electron microscopy and nitrogen adsorption at 77 K. The specific surface area of the products is comparable with this of γ-Al₂O₃. The kinetics of H₂SeO₃ adsorption out of aqueous solutions at 298 K was studied. The adsorption capacity of white rice husks ash was found to be higher than that of black rice husk ash and the adsorption kinetics obeyed the second order kinetic equation.     

Adsorption of phenols from wastewater

The present work involves an investigation of the possible use of coal, residual coal, and residual coal treated with H3PO4 as a means of removal of phenol from wastewater. The study was realized using batch experiments, with synthetic wastewater having phenol concentration of 1000 ppm. Other low-cost adsorbents such as petroleum coke, coke breeze, rice husk, and rice husk char have also been used. The effect of system variables such as pH, contact time, and temperature has been investigated. The suitability of the Freundlich, Langmuir, and Redlich-Peterson adsorption models to the equilibrium data was investigated for each phenol-adsorbent system. The results showed that the equilibrium data for all the phenol-sorbent systems fitted the Redlich-Peterson model best. Kinetic modeling of removal of phenols was done using the Lagergren first-order rate expression. A series of column experiments were performed to determine the breakthrough curves.     

Fibre‐forming blends of polypropylene and polyethylene terephthalate

Bicomponent fibres represent of the new ways for the preparation of synthetic fibres with more variable properties. The polypropylene (PP)‐poly(ethylene terephthalate) (PET) fibre‐forming blend is very interesting because of the improvement of dyeability from bath and some mechanical properties of PP fibres. The new polymer additives containing ester groups which can be added as masterbatches during melting and extrusion processes have been developed in the last years. It has been found that rheological properties of the basic polymer (PP) and polymer additives have a significant role in the blend formation and in spinning. In this work, the influence of some non‐reactive low‐molecular compounds on the processing of fibre‐forming PP‐PET blends and on the properties of blend fibres are presented.     

Bipolymeric Pectin Millibeads Doped with Functional Polymers as Matrices for the Controlled and Targeted Release of Mesalazine

Targeted drug delivery systems are a very convenient method of treating inflammatory bowel disease. The properties of pectin make this biopolymer a suitable drug carrier. These properties allow pectin to overcome the diverse environment of the digestive tract and deliver the drug to the large intestine. This investigation proposed bipolymeric formulations consisting of the natural polymer pectin and a synthetic polymer containing the drug 5-aminosalicylic acid. Pectin beads were prepared via ionotropic gelation involving the interaction between the hydrophilic gel and calcium ions. The obtained formulations consisted of natural polymer, 5-aminosalicylic acid (5-ASA) and one of the synthetic polymers, such as polyacrylic acid, polyvinylpyrrolidone, polyethylene glycol or aristoflex. The release of the drug was carried out employing a basket apparatus (USP 1). The acceptor fluid was pH = 7.4 buffer with added enzyme pectinase to reflect the colon environment. The amount of the released drug was determined using UV-Vis spectrophotometry at a wavelength of λ = 330 nm. The kinetics of the drug dissolution revealed that none of the employed models was appropriate to describe the release process. A kinetic analysis of the release profile during two release stages was carried out. The fastest drug release occurred during the first stage from a formulation containing pectin and polyethylene glycol. However, according to the applied kinetic models, the dissolution of 5-ASA was rather high in the formulation without the synthetic polymer during the second stage. Depending on the formulation, 68–77% of 5-ASA was released in an 8-hour time period. The FTIR and DSC results showed that there was no interaction between the drug and the polymers, but interactions between pectin and synthetic polymers were found.     

Effect on the Solubility,Wettability, and Dispersibility of the β‐CD‐Deltamethrin Inclusion Complex in Presence of Mixed Surfactant (C14MEA/AOS) Blend

An inclusion complex formation using β‐cyclodextrin (β‐CD) as the host molecule and deltamethrin as guest molecule was a first step towards improvement in conventional insecticide formulations. β‐CD‐deltamethrin inclusion complex formation in the absence and presence of the nonionic myrisitic acid monoethanolamide (C₁₄MEA)/anionic α‐olefin sulfonate C₁₂‐C₁₄ (AOS) mixed surfactant system was comparatively studied. The co‐evaporation method was used for complex formation, which was subsequently characterized by analytical methods such as FTIR and XRD techniques. Important physical properties such as solubility, dispersion stability, and wettability were also studied.     

Techno-economic feasibility of biochar as biosorbent for basic dye sequestration

Biochar has a global scientific attention for its ability to remove toxic elements from wastewaters. However, due to the disparity between practical short-term agronomic benefits and aspirations of biochar as an everlasting sustainable bio sorbent for the adsorption process, economic assessments of biochar have yet to be established. In this context, the current study, an economic approach of the biochars derived from agricultural wastes (Coconut shell, Groundnut Shell and Rice husk) for the removal of Basic Red 09 from wastewaters were demonstrated. Batch adsorption experimental set up was used to carry out the adsorption process. At equilibrium batch adsorption conditions, the maximum adsorption capacity of the biochars were 10, 46.3, and 44 ​mg/g for coconut shell, groundnut shell, and rice husk based biochars, respectively. A complete cost assessment was carried out for the agro-waste biochars for their adsorption performance. The biochars derived from groundnut shell and rice husk were shown to be the most cost effective for the Basic Red 09 sequestration from wastewater. The eco-friendly characteristics of these low-cost adsorbents for industrial applications were also discussed.     

Green synthesis and physical properties of crystalline silica engineering nanomaterial from rice husk (agriculture waste) at different annealing temperatures for its varied applications

Crystalline nano silica (SiO₂) was synthesized using a cost-effective eco-friendly method from agricultural waste material like rice husk. Polymer nanocomposite has been prepared using the sol-gel technique from crystalline nano silica using PVA as a polymer binder. Thermal analysis measurement is employed to investigate thermal stability. The XRD analysis shows the crystalline nature of silica is revealed to have characteristic peaks of SiO₂. The particle size was evaluated using Schererr's formula and found to be in the range of 21–31 nm. FTIR measurement shows the presence of O–Si–O (silane) bond formation. The PL measurement shows broad excitation prominently in the visible region. In the XRD pattern, a major peak of the Nanocomposite is observed at an angular position of 19.5° degree, which is more prominent than that of the PVA with the addition of 0.2 wt percent Nano silica to the PVA composite. SEM provides information on homogeneous distribution. This could be beneficial in terms of higher mechanical qualities as well as multifunctional properties. By hydrogen bonding, the PVA molecules are strongly linked to each SiO₂ nanoparticle as measured by FTIR. The stability of materials is confirmed by Zeta Potential and DLS. In the photoluminescence property of SiO₂-PVA crystalline Nano silica composite is excited using a radiation wavelength of 200 nm. The indirect bandgap was determined to be 4.28 eV which could be attributed to the 1100 °C annealing temperature. Such materials may be used as a semiconductor material obtained from a direct natural source, rice husk. Thus, in the present research structural, physical, and optical properties of crystalline nano silica and its polymer composite are explored, which leads us to prepare technological grads material from agricultural waste for varied applications including Agriculture to medical science.     

Evaluation of the properties of some nitrile–butadiene rubber/polychloroprene mixes and vulcanizates

Nitrile–butadiene rubber (NBR) has been blended with polychloroprene (CR) in a weight ratio of 1:1. The vulcanizing systems in the blend formulations were varied to obtain non crosslinked CR embedded in vulcanized NBR and non crosslinked NBR embedded in vulcanized CR. The effects of these two different phases on the rheological and mechanical characteristics were evaluated. In addition, the dynamic compliance of the blends was measured over wide ranges of frequency and temperature. It has been found that the mechanical and rheological properties of the vulcanized blends depend on the type of vulcanizing system, its concentration and the presence of reinforcing filler. The mechanical properties of the blend containing N‐cyclohexyl‐2‐benzthiazyl sulphenamide/S as vulcanizing system suitable for NBR are higher than those of the blend containing non‐sulfur vulcanizing system (Zno/Mgo and ethylene thiourea) suitable for CR. Both types of rubber (CR and NBR) in the blend are incompatible as two glass transition temperatures have been observed. Copyright © 2000 John Wiley & Sons, Ltd.     

Efficient production of nanoporous silicon carbide from rice husk at relatively low temperature

Nanoporous silicon carbide with a specific surface area of up to 186.45 m² g⁻¹ has been efficiently synthesized from waste rice husk using a magnesiothermic reduction at 950 °C as a key step. Throughout the entire process, the recovery rates of silicon, potassium and phosphorus from rice husk can reach 88.46, 91.5 and 65.5%, respectively. Turning rice husk waste into a real treasure, this promising method for producing porous SiC protects the environment and brings economic benefits.     

Improving charge transport in poly(3‐hexylthiophene) transistors via blending with an alkyl‐substituted phenylene–thiophene–thiophene–phenylene molecule

A prototypical semiconducting bicomponent system consisting of a conjugated polymer, that is, poly(3‐hexylthiophene) (P3HT), blended with a small thiophene containing conjugated molecule, that is, an alkyl‐substituted bisphenyl‐bithiophene [phenylene–thiophene–thiophene–phenylene (PTTP)], has been used as an electroactive active layer in field‐effect transistors (FETs). The self‐assembly of this bicomponent system at surfaces has been studied at different length scales, from the nanoscale to the macroscale, and compared with the behavior of monocomponent films of PTTP and P3HT. The correlation between morphology and electric properties of the semiconducting material is explored by fabricating prototypes of FETs varying the relative concentrations of the two‐component blend. The maximum charge carrier mobility value, achieved with a few percent of PTTP component, is not simply due to a uniform dispersion of the molecules in the polymer matrix, but rather to the generation of very long percolation paths, whose composition and electrical properties can be tuned with the PTTP concentration. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012