Synthesis and Nonlinear Optical Properties of New Quadrupolar Chromophores

Two-photon absorption (TPA) has recently received considerable attention because they offer opportunities for both fundamental research and technological applications. The potential applications, including optical data storage, two-photon photodanamic therapy and optical limiting mainly depend on the materials with large two-photon cross section (δTPA)1. Here, we reported two novel chromophores based on symmetric structure of “D-A-Core-A-D”, where D and A stand for electron-donor and e…     

Synthesis of Fullerene-Acrylamide Copolymer Nanoball and Its Lubrication Properties

A novel fuUerene-acrylamide copolymer was synthesized via radical polymerization. It is soluble in polar solvents such as water, dimethyl sulfoxide etc. The product was characterized by FTIR, UV-Vis and GPC. TEM analysis shows that the average particle diameter is about 46 nm. Four-ball tests show that the addition of a certain concentration of the fullerene copolymer to base stock (2 wt% triethanolamine and 0.5 wt% OPZ aqueous solution) can effectively raise the load-carrying capacity (PB value) and the antiwear ability. SEM analysis shows that the addition results in reducing diameter of wear scar and decreasing wear.     

Sol‐Gel Synthesis of Polycrystalline ZnO and ZnS Fibers

ZnO fibers with wurtzite structure have been prepared by a sol‐gel method using zinc nitrate hexahydrate and glucose as starting materials. The ZnO fibers with the diameter in the order of 3–5 µm are composed of ZnO nanoparticles with the size of 40～100 nm. The evolution of gel fibers to ZnO fibers was characterized by TG, XRD, FT‐IR, TEM, and SEM techniques in details. In addition, the transformation of ZnO fibers to ZnS fibers also was investigated.     

Effect of Dispersant on the Colloidal Stability of Nano‐sized CuO Suspension

The stabilization of nano‐sized CuO suspensions was examined to look for the primary mechanism of dispersion. The dispersion stability of suspension was characterized by sedimentation tests, Zeta potential, granularity tests, and infrared spectroscopy (IR). Influence factors such as pH and the concentration of the dispersant on the colloidal stability of the suspension were investigated. The results showed that sodium polyacrylate was fit to stabilize the suspension of CuO nanoparticles through electrosteric repulsion. Also, smaller viscosity and better dispersion effects were achieved when sodium polyacrylate mass fraction was 0.4%～0.8% (based on the powder), pH was 10.     

Synthesis, Structure and Non-linear Optical Properties of Iron Mercury Tetrathiocyanate

IntroductionTheMHg(SCN)4seriesofcrystallinecomplexeshavebeenknowninanalyticalchemistryfortheircharacteristicshapesand..l.,,i.Withthedevelopmentofnon-linearoptics(NLO),thiskindofcoordinationcompoundshavebeendiscoveredtobeusefulasNLOmaterials.In1970s,ItwasreportedthattheN'LOcoefficient(fordoublinginfraredI.064urnNd:YAGlaserbeamtogenerate0.532urngreenlight)ofCdHg(SCN)4wasI.3timesasthatofNLOcrystalLiIO,'.Furthermore,wehaverecentlydiscoveredthattheCdHg(SCN)'crystalcangeneratesecondha…     

Studies of Synthesis and Interfacial Properties of Sodium Branched‐Alkylbenzenesulfonates

Two sodium branched‐alkylbenzensulfonates with additional alkyl substituents were synthesized through a series of reactions. The interfacial tension of these alkylbenzenesulfonates between 1.0% NaCl solution and six n‐alkanes were measured. From the data of measurements the following values were calculated: critical micelle concentration (cmc), the interfacial tension at the cmc (γ_cmc), interfacial excess concentration at the cmc (Γ_m), area per molecule at the cmc (A_m). There were a minimum γ_cmc and a maximum Γ_m appeared for the same n‐alkane with increasing the hydrocarbon chain length of the oil. These indicated that the hydrocarbon chain length of oil have the important effect on adsorption and interfacial tension.     

Synthesis and Properties of Surfactants derived from N‐Acetyl‐D‐Glucosamine

The synthesis of 2‐acetamido‐2‐deoxy‐6‐O‐octanoyl‐D‐glucono‐1,5‐lactone 9 and 2‐acetamido‐2‐deoxy‐6‐O‐octanoyl‐α‐D‐glucopyranose 7 from 2‐acetamido‐2‐deoxy‐α‐D‐glucopyranose is reported. For both targets, the key intermediate was allyl 2‐acetamido‐3,4‐di‐O‐benzyl‐2‐deoxy‐6‐O‐octanoyl‐α‐D‐glucopyranoside 5. Surface tension measurements (critical micellar concentration of 22.3 mM and 5 mM for 9 and 7, respectively) showed up the surface activity of both compounds, while enzyme inhibition assays indicated that 9 could inhibit bovine β‐N‐acetylglucosaminidase (K_i=6.5 µM) but not Serratia marcescens chitobiase nor hen egg‐white lysozyme. Moreover, 7 was shown to induce chitinase production of S. marcescens and to be readily metabolized by these bacteria.      

Optical and Electronic Properties of Different Kinds of Water‐Soluble Porphyrin Films

Water‐soluble porphyrin‐porphyrin and porphyrin‐CdSe nanoparticle monolayer films were self‐assembled on different substrates. The influence of substrates, types of films, and heat treatment temperature on fluorescence of different kinds of porphyrin films was investigated. The SEM images showed the formation of monolayer films on porous alumina foil. The films assembled on porous alumina foil possessed higher fluorescence intensity and thermal stability. The result of conductance measurement indicated that the interaction of trimethylamidophenylporphyrin iodide (TAPPI) molecules with hydroxyl groups on porous alumina foil was weakened after CdSe nanoparticles assembled with TAPPI.     

Synthesis,Structure Characterization and Optical Properties of β Lithium Zinc Phosphate

β-LiZnPO_4 single crystal was successfully synthesized via hydrothermal method. It crystallizes in the trigonal space group R3 with a = b = 13.6490 ?, c = 9.1123 ?, γ = 120.00° and Z = 18. Structure of the crystal is constructed by LiO_4, ZnO_4 and PO_4 tetrahedral units to form a three-dimensional(3 D) framework. The crystal has a high transmission ranging from 350 to 800 nm with UV cut-off edge at 220 nm. The nonlinear optical efficiency of the as-prepared β-LiZnPO_4 is about 1.2 times as large as that of KDP(KH_2PO_4) standard. Additionally, band structure and density of states calculations for β-LiZnPO_4 were performed using the total-energy code CASTEP, based on density functional theory(DFT).     

Synthesis and Properties of Poly(AAm‐KMA‐MA) Hydrogels

In this investigation, poly(acrylamide‐co‐potassium methacrylate‐co‐maleic acid) hydrogels, poly(AAm‐KMA‐MA) were synthesized by redox copolymerization in aqueous solution. The effect of reaction parameters, such as concentration of maleic acid, crosslinking agent, initiator and activator, on the swelling behavior was investigated in detail. The swelling/diffusion characteristics were also evaluated for 1,4‐butanediol diacrylate (BDDA) and 1,2‐ethyleneglycol dimethacrylate (EGDMA) crosslinked hydrogels having different amounts of maleic acid. The results indicate that the water diffusion of hydrogels was of a non‐Fickian type. The hydrogels were characterized by IR spectroscopy and thermogravimetric analysis (TGA). Their surface characteristics were observed by using scanning electron microscopy (SEM). Furthermore, their swelling phenomena in different pH and salt solutions and simulated biological fluids was also studied.     

Sol–gel preparation of TiO2 and MgF2 multilayers

TiO₂ and MgF₂ thin films were prepared by sol–gel processing. Their microstructure was investigated by scanning electron microscopy, X-ray diffraction and ellipsometric porosimetry as a function of the number of coating-firing cycles with different single layer thicknesses. TiO₂/MgF₂ multilayers were processed in different stacking sequences; the nucleation of the subsequent material was correlated to the underlying crystal structure and the respective film morphology. It was found that dense crystalline MgF₂ films on glass can be manufactured by homoepitaxial growth of multiple thin layers. On an underlying TiO₂ layer the effect of densification and crystallization is increased. In the reverse film order no such effect could be observed.     

Synthesis and Characterization of Nano‐Ziconium Dioxide in Recombination Surfactant Association System

This article investigates the influence factors of reagent ratio, pH, stirring intensity, sintering temperature along with ultrasonic wave to particle size, distribution of nanoziconium dioxide in recombination surfactant system. The optimized reagent ratio (wt) of cyclohexan, OP‐10, n‐Amyl alcohol, zircon salt solution are 55%, 17.5%, 17.5%, 10%, respectively. At pH=8.7, the size of nanozirconium oxide has the priority of smaller (<10 nm), narrower particle size distribution and better performance in W/O form.     

Synthesis and Optical Properties of HyperbranchedPAEKs Containing Porphyrin and Its Metal Derivatives简

Novel functional hyperbranched poly(aryl ether ketone)s(HPAEKs) bonded with nonlinear optical chromophores(meso-tetrakis(4-hydroxyphenyl) porphyrin, THPP and its metal derivatives) were synthesized and characterized by 1H-NMR and UV-Vis absorption spectra. The incorporation of chromophores into HPAEKs endowed HPAEKs novel NLO and OL properties. Indeed, dendritic architecture allowed for maximum dispersion of the chromophores, avoided aggregation, more optical limiting property was obtained. Simultaneously, they retained the excellent properties of the materials, particularly in thermal stability. Their optical properties were evaluated by nonlinear optical analyses and optical limiting. The results showed that these polymers possessed good optical limiting(OL) property and large nonlinear optical(NLO) susceptibilities(ca. 10 12esu). All polymers containing chromophores presented excellent thermal stability(DT5 524.17 °C).     

Synthesis and Properties of Aromatic Side Chained N‐Acyltaurate Surfactants

A series of anionic N‐acyltaurate surfactants, side chain containing aromatic nucleus (abbreviated as SAATT), were synthesized via Williamson reaction, hydrolyzation, and acylation. Krafft temperatures and surface properties of these surfactants at 30°C, that is, critical micelle concentration, cmc, surface excess concentration, Γ_max, surface area demand per molecule, A _min, efficiency in surface tension reduction, pC₂₀, effectiveness in surface tension reduction, π_cmc, and cmc/C₂₀ parameter were determined. It was shown that these surfactants exhibit good solubility which was confirmed by measuring Krafft temperature. The cmc of SAATT was much smaller than that of conventional surfactants with similar effective carbon numbers, and shifted to lower concentration with increasing hydrocarbon chain length. In addition, the γ_cmc decreased with decrease in Γ_max. The pC₂₀ and the cmc/C₂₀ got larger with the increase in hydrocarbon chain length. From the fluorescence intensity ratios of I ₁ (373 nm) and I ₃ (384 nm) using pyrene as a probe, it was indicated that the molecules of SAATT formed loose micelles with a broad size distribution.     

Sol–Gel Synthesis of Methyl Modified Optical Silica Coatings and Gels from DDS and TEOS

Methyl modified silica coatings and gels were prepared from dimethyldiethoxysilane and tetraethylorthosilicate via sol–gel processing and spin-coating. The as-synthesized coatings showed not only anti-reflectivity but also hydrophobicity and high laser damage thresholds compared to pure silica coatings without methyl modification. The existence of methyl groups in the framework was demonstrated by IR and NMR spectroscopy. The microstructure of the xerogels obtained were also characterized and will be discussed.     

Synthesis,Characterization, and Photocatalytic Activity of N‐Doped TiO2 Nanotubes

N‐doped TiO₂ nanotubes with high photocatalytic activity were prepared by the combination of sol‐gel process with hydrothermal treatment. The prepared materials are characterized with transmission electron microscopy (TEM), high‐resolution transmission electron microscopy (HRTEM), x‐ray diffraction (XRD), x‐ray photoelectron spectra (XPS), and UV‐vis spectra. Photocatalytic performance of the N‐doped TiO₂ nanotubes is studied by testing the degradation rate of methyl orange under UV irradiation. Obtained results indicate that N‐doped TiO₂ nanotubes have high catalytic activity for photocatalytic oxidation.     

Synthesis and Optical Properties of Fe@Au,Ni@Au Bimetallic Core–Shell Nanoparticles

Fe@Au and Ni@Au core–shell nanoparticles (NPs) were synthesized by liquid-phase reduction of iron and nickel compounds by sodium borohydride in an aqueous medium. Transmission electron microscopy, X-ray powder diffraction, and spectrophotometry were used to confirm the structure of the NPs and to determine their shape and the average core and shell size.     

Synthesis,Structures, and Properties of Novel N‐Aryl‐phenanthren‐o‐iminoquinones

The interaction of 9,10‐phenanthrenquinone with primary amines has been studied. Use of sterically hindered anilines gave the phenanthren‐o‐iminoquinones in good yields. These compounds are structural analogues of o‐benzoquinones. Using single‐electron reduction, o‐iminoquinones may synthesize metal's free‐radical complexes.     

Synthesis of a Thiophene‐Based Nonlinear Optical Chromophore

This report details an eight‐step synthesis of the thiophene‐type nonlinear optical chromophore 1 in 38% overall yield. Only one early step required chromatography.     

Synthesis and Characterization of a Sol–Gel Derived Ureasilicate Hybrid Organic-Inorganic Matrix Containing CdS Colloidal Particles

The electrical properties of sol–gel-derived films can be tailored by embedding conductive particles of ruthenium dioxide or carbon black in an insulating amorphous SiO₂ silica matrix. The preparation process included an acid hydrolysis of tetraethoxysilane and methyltrimethoxysilane. Then alcohol solutions of ruthenium chloride or carbon black were added. Films of filler concentration up to 60 vol.% were prepared by dip coating and then dried and heat-treated at various temperatures up to 600_°C. The D.C. resistance of the films can be varied within the range of 10⁹ to 10^–2 cm. A non-linear dependence on filler composition in the films was observed for both systems, which is explained by a modified percolation theory. A percolation threshold of 5.5 vol.% for SiO₂-RuO₂ or 50 vol.% for SiO₂-C films, whereby the resistance drastically decreases, was determined. Moreover the temperature dependency of resistance and the current-voltage characteristics of the films can also be explained by this geometric model.