Determination of linear alkylbenzene sulfonates in water samples by liquid chromatography-UV detection and confirmation by liquid chromatography-mass spectrometry

A high-performance liquid chromatographic (HPLC) method was developed for the separation and determination of individual (C₁₀-C₁₃) linear alkylbenzene sulfonates (LAS). New sets of conditions have been established for routine analysis of individual chemical forms of four LAS surfactants, i.e. C₁₀-C₁₃ LAS. Under a condition set using a mobile phase containing 1.5 mM ammonium acetate in methanol/water 80:20 (v/v) mixture, detection limits obtained were in the range 1.5 ppb (for C₁₀ LAS) to 11.5 ppb (for C₁₃ LAS). This offers the advantages of significant improvement in resolution, short separation time and using less amount of common salt under isocratic condition. In addition, the use of simple mobile phase containing a simple low amount of salt cannot deposit at the entrance of mass spectrometric detector. The method is applicable to the simultaneous determination of LAS surfactants in various water samples. LAS surfactants presented in these samples were also successfully confirmed by using electrospray mass spectrometry.     

Application of probe sonication extraction for the determination of linear alkylbenzene sulfonates from sewage sludge. Comparison with other extraction methods

A new method based on probe sonication extraction (USP) prior to high performance liquid chromatography (HPLC) has been developed for the determination of linear alkylbenzene sulfonates (LAS) from sewage sludge. The optimized method was designed to be cost effective compared to existing extraction methods (ultrasonic assisted extraction, Soxhlet or pressurized liquid extraction) which may require large quantities of organic solvents, or costly instrumentation or equipment.The main factors affecting the extraction efficiency (extractant volume, ultrasounds power and extraction time) were optimized using compost sludge. The detection limit of total LAS in the sludge was 10 mg kg^− 1. The extraction of C₁₀-C₁₃ homologues is carried out using an extraction time of 7 min with 10 mL of methanol. Liquid chromatography with fluorescence (FL) detector is used for determination of LAS homologues. A mobile phase acetonitrile-water containing 0.1 M NaClO₄ (65:35) and isocratic elution was used. Compounds were eluted over 6 min at a flow rate of 1 mL/min. Polar interferences are eluted between 0 and 2 min and no purification of the samples is required prior to the final determination by high performance liquid chromatography (HPLC). The recoveries of LAS in spiked sewage sludge were between 84.0% and 97.0%, which reflect the efficiency of the method for extraction of these analytes from sewage sludge. Concentration levels found were between 11,858 mg kg^− 1 for digested sludge and 2379 mg kg^− 1 for compost sludge.     

Ion-pair extraction and GC-MS determination of linear alkylbenzene sulphonates in aqueous environmental samples

A GC-MS method was developed for the determination of linear alkylbenzene sulphonates (LAS) and sulphophenylcarboxylic acids (SPC) in aqueous environmental samples. LAS and SPC were isolated from aqueous samples using methylene green (MG) as ion-pair reagent and derivatised with diazomethane for their chromatographic analysis. LAS and SPC were then analysed with GC-MS in EI mode as their methyl esters. The method eliminates positive and negative interferences found by the methylene blue method and considered to be selective and sensitive for the determination of LAS and SPC in aqueous samples. The recovery of LAS was 98% with a relative standard deviation (R.S.D.) of 2.0% and the detection limit obtained from calculations by using GC-MS results based on S/N:3 was lower than 10 ppb. Obtained results revealed that the method can also be employed in the analysis of organic compounds bearing sulphate and sulphonate groups.     

New rapid methods for determination of total LAS in sewage sludge by high performance liquid chromatography (HPLC) and capillary electrophoresis (CE)

Linear alkylbenzene sulfonates (LAS) are the most common synthetic anionic surfactant used in domestic and industrial detergents, with a global production of 2.4 × 10⁶ t year⁻¹. After use and disposal, LAS may enter the environment by one of the several routes, including by direct discharge to surface water or discharge to water from sewage treatment plants. Sewage treatment plants break down LAS only partly: some of them remain in effluent and other fraction is adsorbed in sewage solid.New and rapid methods for determination of total LAS from sewage sludge based on microwave assisted extraction and HPLC-FL and CE-DAD determination are proposed. The extraction of total LAS is carried out by using microwaves energy, an extraction time of 10 min and 5 mL of methanol. For HPLC-FL determination, mobile phase acetonitrile-water was used, comprising 60% (v/v) from 0 to 1 min and a flow rate of 1 mL min⁻¹ programmed to 100% acetonitrile between 1 and 2 min and a flow rate of 2 mL min⁻¹. The final composition was maintained for a further 5 min. The determination of total LAS by CE-DAD was performed in a phosphate buffer (10 mM, pH 9). The separation voltage was 25 kV and the temperature of the capillary was 30 °C. Injections were performed in the pressure mode and the injection time was set at 12 s. The determination of total LAS is carried out in less than 5 min. The methods did not require clean-up or preconcentration steps. Detection limit for total LAS in the sludge was 3.03 mg kg⁻¹ using HPLC-FL and 21.0 mg kg⁻¹ using CE-DAD, and recoveries were >85% using both determination methods. Concentrations of total LAS obtained using both methods were compared with the sum of concentrations of homologues LAS C-10, LAS C-11, LAS C-12 and LAS C-13 obtained using microwaves assisted extraction and HPLC-FL and CE-DAD determination.     

Freely dissolved concentrations of anionic surfactants in seawater solutions: Optimization of the non-depletive solid-phase microextraction method and application to linear alkylbenzene sulfonates

A solid-phase microextraction method (SPME) has been optimized for the analysis of freely dissolved anionic surfactants, namely linear alkylbenzene sulfonates (LAS), in seawater. An effect of the thermal conditioning treatment on the polyacrylate fiber coating was demonstrated for both uptake kinetics and sorption isotherm linearity. Thermal conditioning at 120 °C yielded linear sorption isotherms and reproducible SPME measurements for several individual LAS compounds, with detection limits at the low microgram per liter range. Sorption of LAS to the conditioned SPME fiber was independent of LAS co-solutes in mixtures. The method has been applied to study the precipitation of LAS in seawater, and solubility data for a wide range of individual LAS constituents is presented for the first time. Hence, the developed SPME method for the anionic LAS has shown to be a useful tool in complex matrices. The advantage of the SPME analyses in complex matrices is, besides its simplicity, that it also leads to clean extracts for chromatographic analyses.     

Ultrasonic extraction and LC determination of linear alkylbenzene sulfonate in plant tissues

Summary A new method has been developed for the extraction and determination of linear alkylbenzene sulfonate (LAS) in plant tissues (rice stems and leaves). It consists of methanol-ultrasonic extraction followed by clean-up with aluminum oxide, enrichment with C₁₈ solid-phase extraction column and determination by HPLC. Both efficiency and accurracy of the overall method were high, i.e. mean recovery of: 89% (84 to 93% for LAS concentrations ranging from 1 to 100 mg kg⁻¹) and repeatability of: 3% relative standard deviation for 6 replicate analyses. With a 2 g sample for analysis, LAS levels of 0.5 mg kg⁻¹ in plants could be detected with the proposed method. Further advantages were: it was less time consuming (1 h for extraction), less solvent consumption, and smaller samples (2 to 3 g) required when compared with Soxhlet extraction.     

Capillary electrophoresis for the direct determination of cephalosporins in clinical samples

Summary The possibility of determination of four cephalosporin antibiotics in clinical samples by capillary electrophoresis has been investigated. The separation conditions for capillary zone electrophoresis (CZE) were studied in detail. The precision of migration times measured by use of the optimized method was satisfactory (RSD<1%) and response was linearly dependent on concentration over the approximate range 2–150 mg L⁻¹ for all the compounds studied (cefuroxime, cefotaxime, ceftriaxone, and ceftazidime). Complete separation could be achieved within 5 min. The CZE method was found to be highly suitable for direct determination of the antibiotics in clinical samples such as wound drainage, cerebrospinal fluid, and urine; for serum, however, the use of micellar electrokinetic capillary chromatography (MECC) was more advantageous. Presented at Balaton Symposium '01 on High-Performance Separation Methods, Siófok, Hungary, September 2–4, 2001     

Ionic‐liquid‐modified magnetic nanoparticles as a solid‐phase extraction adsorbent coupled with high‐performance liquid chromatography for the determination of linear alkylbenzene sulfonates in water samples

Novel ionic‐liquid‐functionalized Fe₃O₄ magnetic nanoparticles were synthesized by the thiol‐ene click reaction. The prepared functionalized Fe₃O₄ nanoparticles possessed multiple interactions, such as electrostatic, hydrophobic, and π–π interactions. The functionalized Fe₃O₄ nanoparticles were characterized by using Fourier transform infrared spectroscopy, X‐ray diffraction, vibrating sample magnetometry, and transmission electron microscopy. Four kinds of linear alkylbenzene sulfonates, namely, sodium decylbenzenesulfonate, sodium undecylbenzene sulfonate, sodium dodecylbenzenesulfonate, and sodium tridecylbenzenesulfonate, were selected as model compounds to evaluate the applicability of adsorbents for extraction and subjected to high‐performance liquid chromatography analysis. In addition, the effects of various parameters, such as sorbent amount, pH value, ionic strength, sample volume, extraction time, and elution conditions on extraction efficiency were studied in detail. Under the optimum conditions, good linearities were attained, with correlation coefficients between 0.9912 and 0.9968. The proposed method exhibited limits of detection ranging from 0.061 to 0.099 μg/L for all the target analytes. The spiked recoveries of the target analytes in real water samples ranged from 86.3 to 107.5%, with relative standard deviations lower than 7.96%. The enrichment factors of the analytes ranged from 364 to 391, indicating that the obtained functionalized Fe₃O₄ nanoparticles can effectively extract trace target analytes from environmental water samples.     

Handling of marine and estuarine samples for the determination of linear alkylbenzene sulfonates and sulfophenylcarboxylic acids

Due to the physicochemical properties of linear alkylbenzene sulfonates (LAS), an anionic surfactant, it is difficult to obtain representative samples from sampling sites. Further, the high biodegradability of these compounds makes it necessary to study their biodegradation intermediates, sulfophenylcarboxylic acids (SPC) that do not have a surfactant character and show a different behavior. A procedure for determining and quantifying LAS and SPC in different environmental matrices by Soxhlet and solid-phase extractions and high-performance liquid chromatography is presented. The recoveries varied in the range from 85 to 102% for the water samples, and from 75 to 105% for sediment samples, with a standard deviation of between 1 and 7, and 2 and 11, respectively. Detection limits obtained were in the range from 5 to 10 microg kg(-1) for sediment samples (10 g) and from 0.2 to 0.4 microg l(-1) for water samples (250 ml). The method was applied to the simultaneous determination of LAS (C10-C13) and SPC (C4-C13) homologues in water, sediment and interstitial water collected from different areas of Spain.     

LC-MS determination of linear alkylbenzene sulfonates and their carboxylic degradation products in influent and effluent water samples and sludges from sewage-treatment plants

Linear alkylbenzene sulfonates (LAS) have been determined in samples of the influent and the effluent, and in the sludge, from sewage-treatment plants (STP). LAS and sulfophenyl carboxylate compounds (SPC) were isolated by solid-phase extraction (SPE) with the polymeric phase Isolute ENV, then determined by liquid chromatography-electrospray mass spectrometry (LC-ESI-MS). The method enabled unequivocal identification of C10-C13 LAS by monitoring the ion at m/z 183 and the base peak corresponding to the [M-H]- ion. Average recoveries varied from 77-93% and the linear range of the method varied from 0.2 to 10 microg L(-1), with a limit of detection ranging from 10 ng L(-1) to 1.5 microg L(-1) when 200 mL waste water were preconcentrated. For sewage sludge, recoveries varied from 58 to 90% and the linear range was between 0.2 and 100 microg L(-1), with a detection limit ranging from 0.4 to 120 microg kg(-1) when 2.5 g sewage sludge was extracted. Unequivocal identification and determination of some metabolites of the LAS, the sulfophenyl carboxylate compounds (SPC), was achieved by monitoring [M-H]- ions.     

New sample treatment for determination of linear alkylbenzene sulfonate (LAS) in agricultural soils by liquid chromatography with fluorescence detection

A new sample-treatment procedure has been developed for determination of total linear alkylbenzene sulfonate (LAS), i.e. homologues and isomers, in agricultural soil. The procedure involves two steps, ultrasound-assisted extraction of LAS from the samples with methanol then clean-up of the methanolic extracts and preconcentration of the LAS by solid-phase extraction on two adsorbent cartridges (SAX and C₁₈). The ultrasound-assisted procedure reduces extraction time (10 min in contrast with 6–12 h for conventional Soxhlet extraction) and requires only small volumes of organic solvent. The effect of different variables interacting in the ultrasound-assisted extraction process was studied. Finally, separation and quantification of the homologues and isomers of LAS was performed by liquid chromatography with fluorescence detection (LC?FD). 2-Octylbenzenesulfonic acid sodium salt (Na-2ØC₈-LAS) was used as internal standard. The proposed method was satisfactorily used for determination of LAS in agricultural soil samples from the fertile plain of Granada (Spain).

Open image in new window

Figure LAS treatment, a field experience

     

Field‐amplified sample injection combined with capillary electrophoresis for the simultaneous determination of five chlorophenols in water samples

A sensitive method of CZE‐ultraviolet (UV) detection based on the on‐line preconcentration strategy of field‐amplified sample injection (FASI) was developed for the simultaneous determination of five kinds of chlorophenols (CPs) namely 4‐chlorophenol (4‐CP), 2‐chlorophenol (2‐CP), 2,4‐dichlorophenol (2,4‐DCP), 2,4,6‐trichlorophenol (2,4,6‐TCP), and 2,6‐dichlorophenol (2,6‐DCP) in water samples. Several parameters affecting CZE and FASI conditions were systematically investigated. Under the optimal conditions, sensitivity enhancement factors for 4‐CP, 2‐CP, 2,4‐DCP, 2,4,6‐TCP, and 2,6‐DCP were 9, 27, 35, 43, and 43 folds, respectively, compared with the direct CZE, and the baseline separation was achieved within 5 min. Then, the developed FASI‐CZE‐UV method was applied to tap and lake water samples for the five CPs determination. The LODs (S/N = 3) were 0.0018–0.019 µg/mL and 0.0089–0.029 µg/mL in tap water and lake water, respectively. The values of LOQs in tap water (0.006–0.0074 µg/mL) were much lower than the maximum permissible concentrations of 2,4,6‐TCP, 2,4‐DCP, and 2‐CP in drinking water stipulated by World Health Organization (WHO) namely 0.3, 0.04, and 0.01 µg/mL, respectively, and thereby the method was suitable to detect the CPs according to WHO guidelines. Furthermore, the method attained high recoveries in the range of 83.0–119.0% at three spiking levels of five CPs in the two types of water samples, with relative standard deviations of 0.37–8.58%. The developed method was proved to be a simple, sensitive, highly automated, and efficient alternative to CPs determination in real water samples.     

Stacking and simultaneous determination of estrogens in water samples by CE with electrochemical detection

A rapid and sensitive method based on transient ITP and field enhancement in CE with electrochemical detection at copper disk electrode was developed for the simultaneous separation and determination of three estrogens: estrone, 17β‐estradiol, and estriol. The effects of several important factors that influence the separation and detection were investigated. Under the optimum conditions, the estrogens could be separated in 0.06 mol/L sodium hydroxide solution within 14 min. With transient ITP by addition of 0.5% NaCl, a good linear response was obtained for three estrogens from 0.2 to 10 μmol/L, with correlation coefficients higher than 0.9993. The detection limits were 8.9 × 10^?8, 6.7 × 10^?8, and 1.1 × 10^?7 mol/L (S/N = 3) for estriol, 17β‐estradiol, and estrone, respectively. This method was successfully employed to analyze different water samples from waterworks, tap water, fishpond, and river samples with recoveries in the range of 90.8–108.9%, and RSDs < 4.69%. The satisfied results demonstrated that this method was of convenient preparation, high sensitivity, and good repeatability, which could be applied to the rapid determination of environmental water samples.     

In-capillary solid-phase extraction-capillary electrophoresis for the determination of chlorophenols in water

A novel CE method combined with SPE in a single capillary was developed for analysis of chlorophenols in water. A frit of 0.5 mm was first made by a sol-gel method, followed by packing a SPE sorbent in the inlet end of the capillary. Two phenol derivatives, 2,4-dichlorophenol and 2,4,5-trichlorophenol, were used as the model compounds. By loading sample solutions into the capillary, the two chlorophenols were extracted into the sorbent. They were desorbed by injecting only about 4 nL of methanol. Finally, the analytes were separated by conventional CE. The technique provided a concentration enhancement factor of over 4000-fold for both chlorophenols. The detection limits (S/N = 3) of 2,4-dichlorophenol and 2,4,5-trichlorophenol were determined to be 0.1 ng/mL and 0.07 ng/mL, respectively. For replicate analyses of 5 ng/mL of 2,4-dichlorophenol, within-day and between-day RSDs of migration time, peak height and peak area were in the range of 1.8-2.0%, 4.0-4.4% and 4.1-4.6%, respectively. The method shows wide linear range, acceptable reproducibility and excellent sensitivity, and it was applied to the analyses of spiked river water samples. The capillary packed with the SPE sorbents can be used for more than 400 runs without performance deterioration.     

Counter-flow electrokinetic supercharging for the determination of non-steroidal anti-inflammatory drugs in water samples

Electrokinetic supercharging (EKS) has been used in the last few years as a powerful tool for separation and on-line preconcentration of different types of analytes. We have developed a valuable modification for EKS system, namely counter-flow EKS (CF-EKS) and applied it for the separation and on-line preconcentration of seven non-steroidal anti-inflammatory drugs (NSAIDs) in water samples. In CF-EKS, a hydrodynamic counter-flow is applied during electrokinetic injection of the analytes within the EKS system. This counter-flow minimises the introduction of the sample matrix into the capillary, allowing longer injections to be performed. Careful choice of the optimum counter-flow as well as the optimum injection voltage allowed the sensitivity to be enhanced by 11,800-fold, giving limits of detection (LODs) of 10.7–47.0 ng/L for the selected NSAIDs. The developed method was validated and then applied for the determination of the studied NSAIDs in drinking water as well as wastewater samples from Hobart city.     

The determination of the linear alkylbenzene sulfonate isomers in water samples by gas-chromatography/mass spectrometry

A number of 20 compounds of linear alkylbenzene sulfonates (LASs) family were identified by electron impact mass spectrometry (EI-MS) in water samples collected from wastewater treatment plants (WWTP). This paper presents the mass spectra of 20 compounds, the proposed mechanism of formation of the diagnostic ions obtained by EI-MS and the distribution of individual isomers in water samples collected from compartments of WWTP. The individual isomers from four homolog series C(10)-, C(11)-, C(12)- and C(13)-LAS were analyzed as methyl derivatives.     

Efficient capillary electrophoresis separation and determination of free amino acids in beer samples

Simultaneous detection of various o‐phthalaldehyde (OPA)‐labeled amino acids (AAs) in food samples was reported based on CE separation. Ionic liquid was used for the first time for CE analysis of AAs with in‐capillary derivatization. Several other additives, including SDS, α/β‐CD, and ACN, as well as key parameters for CE separation (buffer pH value, separation voltage), were also investigated. Our results show that the multiple additive strategy exhibits good stable and repeatable character for CE analysis of OPA‐labeled AAs, for either in‐capillary derivatization or CE separation, and allows simultaneous quantification of different OPA‐labeled AAs in a large concentration range of 50 μM to 3.0 mM with LOD down to 10 μM. Seventeen OPA‐labeled AAs, except for two pairs of AAs (His/Gln and Phe/Leu), which were separated with resolutions of 1.1 and 1.2, respectively, were baseline separated and identified within 23 min using the present multiple additive strategy. The method was successfully applied for simultaneous analysis of AAs in seven beer samples and as many as eleven trace‐amount AAs were detected and quantified, indicating the valuable potential application of the present method for food analysis.     

Sequential injection-bead injection-lab-on-valve coupled to high-performance liquid chromatography for online renewable micro-solid-phase extraction of carbamate residues in food and environmental samples

A sequential injection‐bead injection‐lab‐on‐valve system was hyphenated to HPLC for online renewable micro‐solid‐phase extraction of carbamate insecticides. The carbamates studied were isoprocarb, methomyl, carbaryl, carbofuran, methiocarb, promecarb, and propoxur. LiChroprep^® RP‐18 beads (25–40 μm) were employed as renewable sorbent packing in a microcolumn situated inside the LOV platform mounted above the multiposition valve of the sequential injection system. The analytes sorbed by the microcolumn were eluted using 80% acetonitrile in 0.1% acetic acid before online introduction to the HPLC system. Separation was performed on an Atlantis C‐18 column (4.6×150 mm, 5 μm) utilizing gradient elution with a flow rate of 1.0 mL/min and a detection wavelength at 270 nm. The sequential injection system offers the means of performing automated handling of sample preconcentration and matrix removal. The enrichment factors ranged between 20 and 125, leading to limits of detection (LODs) in the range of 1–20 μg/L. Good reproducibility was obtained with relative standard deviations of <0.7 and 5.4% for retention time and peak area, respectively. The developed method has been successfully applied to the determination of carbamate residues in fruit, vegetable, and water samples.