Fe-Ag/Al_2O_3催化丙烯还原NO的实验研究

以蜂窝状陶瓷为载体,采用溶胶凝胶法和浸渍法制备了不同Fe/Ag负载量的Fe-Ag/Al_2O_3催化剂。以C_3H_6为还原剂,在模拟烟气条件下和200-700℃范围内,程序控温的陶瓷管流动反应器上进行了催化还原NO的性能评估。结果表明,7.2Fe/1.9Ag/20Al_2O_3/CM在500和550℃时催化C_3H_6还原NO的脱硝效率分别超过90%和达到100%。铁离子能有效地提高Ag/20Al_2O_3/CM催化剂抵抗烟气中的SO_2和H_2O的能力。结果表明,当烟气中含有体积分数为0.02%的SO2和8%的H_2O时,在500℃时7.2Fe/1.9Ag/20Al_2O_3/CM催化C_3H_6还原NO的脱硝效率不受影响,在6 h的连续实验中保持90%的脱硝效率而没有下降。而未经铁离子修饰的2Ag/20Al_2O_3/CM的催化活性则受烟气中的SO2和H_2O影响很大,0.02%的SO2和8%的H_2O分别使2Ag/20Al_2O_3/CM在500℃时催化C_3H_6还原NO的脱硝效率迅速从70%分别下降至46%和25%。XRD和SEM表征结果表明,经铁离子修饰后的7.2Fe/1.9Ag/20Al_2O_3/CM催化剂中,形成了AgFeO_2以及Fe~(3+),催化剂表面变得疏松多孔,形成以Fe_3O_4为主的针状和片状晶体。H_2-TPR结果表明,7.2Fe/1.9Ag/20Al_2O_3/CM比Ag/20Al_2O_3/CM在更宽的温度范围内具有更好的还原特性。吡啶吸附红外光谱(Py-FTIR)实验结果显示,Fe增加了催化剂表面的Lewis酸性位。     

Gas-phase interaction of H2S with O2: A kinetic and quantum chemistry study of the potential energy surface

Quantum chemical calculations were carried out to study the interaction of hydrogen sulfide with molecular oxygen in the gas phase. The basic mechanism, the rates of reaction, and the potential energy surface were calculated. Isomers and transition states that connect the reactants with intermediates and products of reaction were identified using the G2 method and B3LYP/6-311+G(3df,2p) functional. Hydrogen abstraction to form HO2 + SH is the dominant product channel and proceeds through a loose transition state well-described at the level of calculation employed. The temperature dependence of the rate coefficient in the range 300-3000 K has been determined on the basis of the ab initio potential energy surface and with variational transition-state theory. The reaction is 169.5 kJ mol(-1) endothermic at 0 K with a rate constant given by 2.77 x 10(5) T(2.76) exp(-19 222/T) cm3 mol(-1) s(-1) and should proceed slowly under atmospheric thermal conditions, but it offers a route to the initiation of H2S combustion at relatively low temperatures.     

Determination of aluminium in AlCl3 and Al2O3 modified silica catalyst supports

X-ray fluorescence spectrometry (XRF) was applied to determine aluminium in AlCl₃- and Al₂O₃-modified silica catalyst supports that were prepared by gas-solid reactions in an atomic layer epitaxy (ALE) process using aluminium chloride or aluminium chloride and water as adsorbates and silica as support. INAA and AAS were used as reference methods to determine the aluminium content of the supports. The calibration of XRF results was done by plotting the Al/Si intensity ratios against the aluminium content as determined by atomic absorption spectrometry (AAS) and verified by instrumental neutron activation analysis (INAA). Correlation factors for the calibration graphs were 0.984 for AlCl₃/SiO₂ and 0.995 for Al₂O₃/ SiO₂ samples in the aluminium content range 0–2.6 g Al per 100 g of sample. Received: 19 October 1998 / Accepted: 14 December 1998     

Determination of aluminium in AlCl3 and Al2O3 modified silica catalyst supports

X-ray fluorescence spectrometry (XRF) was applied to determine aluminium in AlCl₃- and Al₂O₃-modified silica catalyst supports that were prepared by gas-solid reactions in an atomic layer epitaxy (ALE) process using aluminium chloride or aluminium chloride and water as adsorbates and silica as support. INAA and AAS were used as reference methods to determine the aluminium content of the supports. The calibration of XRF results was done by plotting the Al/Si intensity ratios against the aluminium content as determined by atomic absorption spectrometry (AAS) and verified by instrumental neutron activation analysis (INAA). Correlation factors for the calibration graphs were 0.984 for AlCl₃/SiO₂ and 0.995 for Al₂O₃/ SiO₂ samples in the aluminium content range 0–2.6 g Al per 100 g of sample. Received: 19 October 1998 / Accepted: 14 December 1998     

氢气对Ag/Al2O3和Cu/Al2O3催化剂选择性催化C3H6还原Nox反应的影响

 添加H2对Ag/Al2O3和Cu/Al2O3催化剂选择性催化C3H6还原NOx反应具有不同的影响. 原位漫反射红外光谱分析表明,在Ag/Al2O3催化剂上, H2的存在促进了C3H6部分氧化产物烯醇式物种(RCH=CH-O-)和乙酸盐等的形成,烯醇式物种和硝酸盐为主要反应中间体,二者间的相互反应性能很强,能形成高浓度的反应关键中间体异氰酸酯(-NCO)表面吸附物种,因此NOx的去除活性提高; 而在Cu/Al2O3催化剂上, H2的存在并没有促进C3H6部分氧化产物的形成,而且抑制了硝酸盐的形成,进而抑制了C3H6部分氧化产物与硝酸盐反应形成表面-NCO 物种,导致NOx的去除活性降低.     

Hydrothermal Synthesis of Porous Al2O3/Al Metal Ceramics: III. Effect of the Thermal Dehydration of Bayerite on the Formation of a Porous Al2O3/Al Composite

It was found that the diffusion permeability of a porous cover on aluminum particles increased as a result of the structural transformations of bayerite into active aluminum oxide on the thermal treatment of a porous Al(OH)₃/Al composite. The cyclic treatment (each cycle included a treatment with water at 100°C and a thermal treatment at 550°C) eliminated diffusion limitations and resulted in the formation of porous Al₂O₃/Al metal ceramics with a required set of adsorption–structure and mechanical properties. The following two competing processes were found to affect the formation of the mechanical properties of the synthesized material: the formation of new contacts in the course of the precipitation of aluminum hydroxide and the degradation of old contacts under the action of mechanical stresses that appear in the course of synthesis.     

Homocatenation of Aluminum: Alkane‐like Structures of Li2Al2H6 and Li3Al3H8

A new class of aluminum homocatenated compounds (Li_nAl_nH_2n+2) is proposed based on quantum chemical calculations. In these compounds, Al abstracts an electron from Li, becoming valence isoelectronic with C, Si, and Ge, thus mimicking respective structural features of Group 14 hydrides. Using the Coalescence Kick search program coupled with density functional theory calculations, we investigated the potential energy surfaces of Li₂Al₂H₆ and Li₃Al₃H₆. Then single‐point‐energy coupled‐cluster calculations were performed for the lowest energy structures found. Indeed, the global minima established for Li₂Al₂H₆ and Li₃Al₃H₆ contain the Al₂H₆^2? and Al₃H₆^3? kernels, which are isostructural with ethane (C₂H₆), disilane (Si₂H₆), digermane (Ge₂H₆) and propane (C₃H₈), trisilane (Si₃H₈), trigermane (Ge₃H₈) molecules, respectively. Structural, energetic, and electronic characteristics of the Li₂Al₂H₆ and Li₃Al₃H₈ compounds are presented and the viability of their synthesis is discussed.     

Study on the mechanism of catalytic synthesis of dimethyldichlorosilane by AlCl3/MIL‐53(Al)@γ‐Al2O3

Dimethyldichlorosilane, one of the most consumed organosilicon monomers in the industry, can be prepared in a highly efficient and environmentally friendly synthesis method of disproportionating methylchlorosilanes. However, the internal mechanism of the reaction remains unclear. In this paper, the mechanism catalyzed by AlCl₃/MIL‐53(Al) and AlCl₃/MIL‐53(Al)@γ‐Al₂O₃ catalysts was calculated at B3LYP/6‐311++G(3df, 2pd) level by using the density functional theory (DFT). The results showed that although the two catalysts had similar active structures, the catalytic effects were significantly different. The Lewis acid center on the surface of γ‐Al₂O₃ in the core‐shell catalyst is complementary to the classic Lewis acid AlCl₃ through the spatial superposition effect, which greatly improves the Lewis acid catalytic activity of AlCl₃/MIL‐53(Al)@γ‐Al₂O₃.     

Fe2O3–Al2O3 oxygen carrier materials for chemical looping combustion,a redox thermodynamic and thermogravimetric evaluation in the presence of H2S

Journal of Thermal Analysis and Calorimetry - Alumina-supported Fe2O3 oxygen carrier material (OCM) system is among the most promising OCM systems for solid and gaseous fuel CLC. This work utilizes...     

Ab initio study of structures and energies of Al2H4 and Al2H 4 −

The low-lying isomers of Al₂H₄ and their anions are investigated with the hybrid density functional B3LYP, the coupled-cluster CCSD and CCSD(T) methods, and the electron propagator theory. The positive adiabatic electron affinities 5,798 and 10,112 cm⁻¹ are predicted for the neutral C_2v and D_2d symmetric isomers, respectively. The D_2h symmetric anion is more stable by 852 cm⁻¹ than the C_2v symmetric anion. The photodetachment spectra for Al₂H₄⁻ anions at the C_2v and D_2h symmetries are simulated on the basis of the Franck–Condon factor calculations, indicating a reasonable way to study the transition state of the intramolecular torsion process     

The thermodynamic effect of fluorine as a substituent: Allylic CF3 and CF2H

Cope rearrangements of 7,7,7-trifluoro-1,5-heptadiene and 7,7-difluoro-1,5-heptadiene were examined to gain quantitative understanding of the thermodynamic effect of allylic fluorine substitution. Group value contributions to ΔH_f's were thus able to be determined for allylic fluorine-substituted carbon groups: C(F)₃(C_d) = ?166.0, C(F)₂(H)(C_d)= ?107.6 and C(F)(H)₂(C_d) = ?52.2 kcal/mole.     

In situ reaction mechanism studies on the atomic layer deposition of Al2O3 from (CH3)2AlCl and water

Reaction mechanisms between dimethylaluminum chloride and deuterated water in the atomic layer deposition (ALD) of Al2O3 were studied at 150-400 degrees C using a quartz crystal microbalance (QCM) and a quadrupole mass spectrometer (QMS). The observed reaction byproducts were DCl and CH3D. QMS showed that about one-third of the chlorine, and half of the methyl ligands were released during the (CH3)2AlCl pulse. The growth rate deduced from the QMS and QCM data was in qualitative agreement with the previously published growth rate from ALD film growth experiments.     

Sequential addition of H2O, CH3OH, and NH3 to Al3O3-: a theoretical study

Photoelectron spectra of two species, Al3O3(H2O)2- and Al3O3(CH3OH)2-, that are produced by the addition of two water or methanol molecules to Al3O3- are interpreted with density-functional geometry optimizations and electron propagator calculations of vertical electron detachment energies. In both cases, there is only one isomer that is responsible for the observed spectral features. A high barrier to the addition of a second molecule may impede the formation of Al3O3N2H6- clusters in an analogous experiment with NH3.     

A thermodynamic and kinetic study of hydride transfer of a caffeine derivative

One representative type of heterocyclic compound that can release a hydride ion is 7,8-dihydro-9-methylcaffeine (CAFH). The one-electron oxidation potential of CAFH [-0.294 (V vs Fc(+/0))] and the one-electron reduction potential of CAF(+) [-2.120 (V vs Fc(+/0))] were obtained using two different methods, CV and OSWV. Applying titration calorimetry data in thermodynamic cycles, the enthalpies of CAFH releasing a hydride ion [57.6 kcal/mol] and releasing a hydrogen atom [80.3 kcal/mol] and of its radical cation CAFH(?+) releasing a proton [33.0 kcal/mol] and releasing a hydrogen atom [38.4 kcal/mol] have been determined. Several conclusions can be drawn from the thermodynamic results: (1) CAFH is a very good single-electron donor whose single-electron oxidation potential is much less positive than that of NAD(P)H model compound BNAH [E(ox) = 0.219 V vs Fc(+/0)]. (2) The single-electron reduction potential of CAF(+) is much more negative than that of BNA(+) [E(red) = -1.419 V], which means that CAF(+) is not a good electron acceptor. Furthermore, CAFH is a very good hydride donor compared to BNAH. The results of non-steady-state kinetic studies, for the reaction of CAFH and AcrH(+)ClO(4)(-), show that the ratio of t(0.50)/t(0.05) is larger than 13.5 and the ratio of k(init)/k(pfo) is larger than 1. The pseudo-first-order rate constants obtained at different reaction stages decrease with the time, and the kinetic isotope was observed to be small at a short reaction time and slowly increases to 3.72 with the progress of the reaction. These kinetic results clearly display that the hydride transfer of CAFH to AcrH(+) in acetonitrile is not a one-step mechanism, while the thermodynamic results show that CAFH is a very good electron donor. The combination of the kinetic results with the thermodynamics analysis shows that the hydride transfer of the caffeine derivative CAFH takes place by a two-step reversible mechanism and there is an intermediate in the reaction.     

Theoretical and kinetic study of the H + C2H5CN reaction

The reaction of H radical with C₂H₅CN has been studied using various quantum chemistry methods. The geometries were optimized at the B3LYP/6‐311+G(d,p) and B3LYP/6‐311++G(2d,2p) levels. The single‐point energies were calculated using G3 and BMC‐CCSD methods based on B3LYP/6‐311++G(2d,2p) geometries. Four mechanisms were investigated, namely, hydrogen abstraction, C‐addition/elimination, N‐addition/elimination and substitution. The kinetics of this reaction were studied using the transition state theory and multichannel Rice‐Ramsperger‐Kassel‐Marcus methodologies over a wide temperature range of 200–3000 K. The calculated results indicate that C‐addition/elimination channel is the most feasible over the whole temperature range. The deactivation of initial adduct C₂H₅CHN is dominant at lower temperature with bath gas H₂ of 760 Torr; whereas C₂H₅+HCN is the dominant product at higher temperature. Our calculated rate constants are in good agreement with the available experimental data. © 2009 Wiley Periodicals, Inc. J Comput Chem, 2010     

添加金属对MoO3/Al2O3 碳化过程的影响

The investigation on MoO3 / Al2O3 sample or its modifiers with nickel,copper or potassium was performed using temperature programmed surface reaction（TPSR）technique and measurements of BET surface area. The results indicate that addition of nickel promotes the methane reduction,further the carburization,of MoO3,and addition of nickel also promotes the activation of methane over the surface of oxycarbide or carbide due to the increase of active sites per unit area and intrinsic activity of catalytic centers. This is favorable to the conversion of methane. The addition of copper promotes the methane reduction,further the carburization,of MoO3 to some extent,while the introduction of copper also accelerates the sintering of catalyst to a degree. Thus copper doped carbide catalyst exhibits its exceptionally catalytic performance. However,potassium prevents the MoO3 from reduction with methane,which is unfavorable to the carburization. Potassium also restrains methane from being activated over the surface of oxycarbide or carbide. MoO3 / Al2O3 doped with potassium is of lower specific area,which originates from its boosting sintering of catalyst. This caauses the inferior methane conversion over potassium doped carbide catalyst.     

Products of the addition of water molecules to Al3O3- clusters: structure, bonding, and electron binding energies in Al3O4H2-, Al3O5H4-, Al3O4H2, and Al3O5H4

Two stable products of reactions of water molecules with the Al3O3- cluster, Al3O4H2- and Al3O5H4-, are studied with electronic structure calculations. There are several minima with similar energies for both anions and the corresponding molecules. Dissociative absorption of a water molecule to produce an anionic cluster with hydroxide ions is thermodynamically favored over the formation of Al3O3-(H2O)n complexes. Vertical electron detachment energies of Al3O4H2- and Al3O5H4- calculated with ab initio electron propagator methods provide a quantitative interpretation of recent anion photoelectron spectra. Contrasts and similarities in these spectra may be explained in terms of the Dyson orbitals associated with each transition energy.     

Ab initio chemical kinetic study on the reactions of ClO with C2H2 and C2H4

The mechanisms for the reactions of ClO with C(2)H(2) and C(2)H(4) have been investigated at the CCSD(T)/CBS level of theory. The results show that in both systems, the interaction between the Cl atom of the ClO radical and the triple and double bonds of C(2)H(2) and C(2)H(4) forms prereaction van der Waals complexes with the O-Cl bond pointing perpendicularly toward the π-bonds, both with 2.1 kcal/mol binding energies. The mechanism is similar to those of the HO-C(2)H(2)/C(2)H(4) systems. The rate constants for the low energy channels have been predicted by statistical theory. For the reaction of ClO and C(2)H(2), the main channels are the production of CH(2)CO + Cl (k(1a)) and CHCO + HCl (k(1b)), with k(1a) = 1.19 × 10(-15)T(1.18) exp(-5814/T) and k(1b) = 6.94 × 10(-21) × T(2.60) exp(-6587/T) cm(3) molecule(-1) s(-1). For the ClO + C(2)H(4) reaction, the main pathway leads to C(2)H(4)O + Cl (k(2a)) with the predicted rate constant k(2a) = 2.13 × 10(-17)T(1.52) exp(-3849/T) in the temperature range of 300-3000 K. These rate constants are pressure-independent below 100 atm.     

A kinetic study of the chemistry of the SO2 (3B1) reactions with cis- and trans-2-butene

The chemical reactions of SO₂(³B₁) molecules with cis- and trans-2-butene have been studied in gaseous mixtures at 25°C by excitation of SO₂ within the SO₂(³B₁) → SO₂(+, ¹A₁) ‘forbidden’ band using 3500–4100-Å light. The initial quatum yields of olefin isomerization were determined as a function of the [SO₂]/[2-butene] ratio and added gases, He and O₂. The kinetic treatment of these data suggests that there is formed in the SO₂(³B₁) quenching step with either cis- or trans-2-butene, some common intermediate, probably a triplet addition complex between SO- and olefin. It decomposes very rapidly to form the 2-butene isomers in the ratio [trans-2-butene]/[cis-2-butene] = 1.8. In another series of experiments SO₂ was excited using a 3630 ± 1-Å laser pulse of short duration, and the SO₂(³B₁) quenching rate constants with the 2-butenes were determined from the SO₂(³B₁) lifetime measurements. The rate constants at 21°C are (1.29 ± 0.18) × 10¹¹ and (1.22 ± 0.15) × 10¹¹ l/mole·sec with cis-2-butene and trans-2-butene, respectively, as the quencher molecule. Within the experimental error these quenching constants equal those derived from the quantum yield data. Thus the rate-determining step in the isomerization reaction is suggested to be the quenching reaction, presumably the formation of the triplet SO₂-2-butene addition complex. In a third series of experiments using light scattering measurements, it was found that the aerosol formation probably originates largely from SO₃ and H₂SO₄ mist formed following the reaction SO₂(³B₁) + SO₂ → SO₃ + SO(³Σ^?). Aerosol formation from photochemically excited SO₂-olefin interaction is probably unimportant in these systems and must be unimportant in the atmosphere.     

A kinetic study of methane conversion by a dinitrogen microwave plasma

Conversion of CH₄ with a N₂ microwave plasma (2.45 GHz) is studied. The experiments cover the absorbed microwave power range 300–700 W with 17–62% of methane in the gas mixture, with pressures of 10–40 mbar and flow rates of 140–650 ml· min^–1. The yields of C₂ hydrocarbons and dihydrogen are analyzed by gas chromatography. The distance of methane addition downstream of the plasma plays an important role on the composition and the concentration of the products obtained. This distance mainly determines the energy concentrated in the active species of the plasma when they react with methane. Different behaviors for acetylene formation, on the one hand, and for ethane and ethene formation, on the other hand, have been observed, and this finding allows us to propose a kinetic mechanism for the decay of methane and for the formation of C₂ hydrocarbons.