pH-effects in the complex formation of polymers I. Interaction of poly(acrylic acid) with poly(acrylamide)

The effects of polymer concentration, molecular weight of poly(acrylic acid) (PAA), addition of sodium, potassium, ammonium and copper (II) chlorides on the complex formation ability of the system PAA-poly(acrylamide) (PAAM) have been studied in aqueous solutions. The critical pH values of the complexation were determined in different conditions. The complex formation ability of PAAM is compared with other non-ionic polymers. It was shown that an increase in polymers concentration, molecular weight of PAA and ionic strength favours the complexation and shifts the critical pH values to the higher pH region. An addition of CuCl₂ to the mixture of two polymers enhances the complexation drastically due to the formation of triple complexes.     

Complexation between poly(acrylic acid) and poly(vinylpyrrolidone): Influence of the molecular weight of poly(acrylic acid) and small molecule salt on the complexation

Poly(acrylic acid) (PAA) with different molecular weight and poly(vinylpyrrolidone) (PVP) were prepared by free radical polymerization using 2,2′-azoisobutyronitrile (AIBN) as initiator in anhydrous methanol for PAA, and in distilled water for PVP. Then, the complexation between PAA and PVP in aqueous solution was studied by UV transmittance measurement and fluorescence probe technique. The result shows that (1) at low pH, the formation of complexation between PAA and PVP bases on the intermacromolecular hydrogen bond and the composition of the formed complex is around 3:2 (the unit molar ratio of PAA to PVP) at pH 2.60 over the range of pH investigated. (2) The cooperative interaction through the formation of hydrogen bond among active sites plays an important role in complex formation, and depends on the pH of solution, the required minimum chain length of poly(acrylic acid). (3) The hydrogen bond is not affected by small molecular salt, which only affects those carboxylic groups without forming hydrogen bond on the PAA chain.     

Binding of a surfactant counterion to low-charge-density poly(acrylic acid) and poly(methacrylic acid)

The binding of a cationic surfactant, dodecylpyridinium (C12Py) chloride, with a low-charge-density poly (methacrylic acid) (PMA) was investigated in buffer solutions under the condition of constant pH. The binding isotherms with PMA consisted of two and three steps at a pH lower and higher than 3.2, respectively. Bindings in the first step were independent of pH and this step was considered to correspond to the solubilization of the hydrocarbon chains of C12Py into the nonpolar region of the compact form of PMA. This is the indication of the compact form from the binding isotherm. At pH higher than 3.2, the second step was discriminated and it depended on the pH. In the third step, a sharp rise in the degree of binding (β) was observed accompanying the solubilization of the precipitates of the PMA–C12Py complex. The binding with poly(acrylic acid) (PAA) and PMA in conventional unbuffered NaCl solutions was also examined and the pH profile of the solution during the binding process was determined. In the case of unbuffered NaCl solutions, the binding with PAA took place cooperatively at the critical association concentration (cac). The binding isotherm consisted of two steps and the pH decreased with the increase in β. The binding isotherm of PMA, on the other hand, consisted of three steps: the pH decreased slightly in the first step and considerably in the second step with the increase in β but it increased with β in the third step, exhibiting a pH minimum around 3.2. The binding in the first step coincided with that obtained in the buffered solutions. Linear relationships between β and the pH were found for both polymers. In the case of PMA, no cac was observed in both buffered and unbuffered NaCl solutions. Received: 24 January 2001 Accepted: 23 May 2001     

Molecular weight influence on viscosimetric parameters of poly(4-vinylpyridine) polymers

This work describes the effect of the molecular weight on the viscosimetric parameters of poly(4-vinylpyridine) (P4VP) polymers in ethanolic solution. Numerous studies concerning this question have been reported in very separate intervals of molecular weight. We have observed a discordance (discontinuity) in the variation of the intrinsic viscosity as a function of the molecular weight of these polymers ([η]=f(M_w)). In order to establish a general relationship between viscosimetric parameters and M_w, we have considered 10 P4VP samples in a wide interval of molecular weights: 0.75×10⁴ to 153×10⁴. These results have been compared and completed with that of the literature. We have observed that:

(i)

All viscosimetric parameters (intrinsic viscosity [η], Huggins constant k_H, second virial coefficient, viscosimetric expansion coefficient α_η, and critical concentration) change according to a continuous function without a break.

(ii)

The lower is the molecular weight of P4VP; the higher are the variations of the expansion coefficient and the interaction effects.

(iii)

The variation of the intrinsic viscosity versus the molecular weight follows a unique relation in the whole M_w range. In fact, the Berkowitz equation (1), described for a limited range of relatively high M_w (10⁵ to 18.5×10⁵) is extended for all M_w interval values.

(iv)

Empiric laws for [η], k_H, A₂ and C^* and variations as a function of molecular weight were proposed for the P4VP in ethanol.

     

Interpolymer complexes of poly(acrylic acid) with poly(2-hydroxyethyl acrylate) in aqueous solutions

Complexes formed from poly(acrylic acid) and poly(2-hydroxyethyl acrylate) were studied in aqueous solutions by viscometric, turbidimetric, FTIR spectroscopic, and thermogravimetric analysis methods. The formation of interpolymer complexes stabilized by hydrogen bonds was observed. It was found that the compositions of these interpolymer complexes are strongly dependent on the concentration of polymers, the order of mixing the solutions, and the pH. It was demonstrated that the complexation ability of poly(2-hydroxyethyl acrylate) is relatively low compared to other known nonionic water-soluble polymers. However, it can be significantly increased via hydrophobic modification of the poly(acrylic acid) using cetyl pyridinium bromide.     

Preparation and characterization of poly(acrylic acid)-based nanoparticles

The present investigation describes the synthesis and characterization of nanoparticles based on poly(acrylic acid) (PAA) intramolecularly cross-linked with diamine, 2,2′-(ethylenedioxy)bis(ethylamine), using water-soluble carbodiimide. The aqueous colloid dispersions of nanoparticles were clear or mildly opalescent depending on the ratio of cross-linking, pH of the solution, and the molecular weight of PAA, finding consistent with values of transmittance between 3% and 99%. The structure was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by dynamic light scattering (DLS) and transmission electron microscopy (TEM) measurements. It was found that particle size depends on the pH, and at a given pH, it was caused by the ratio of cross-linking and the molecular weight of PAA. Particle size measured by TEM varied in the range of 20 and 80 nm. In the swollen state, the average size of the particles measured by DLS was in the range of 35–160 nm.     

The synthesis and characterization of monodisperse poly(acrylic acid) and poly(methacrylic acid)

A number of polyacrylic (PAA) and polymethacrylic (PMAA) acids have been synthesized by living anionic polymerization of the monomeric tert-butyl esters followed by subsequent hydrolysis of the corresponding polyesters. The necessary precautions were taken in order to assure good molecular weight control, as well as high yields in the polymerization reactions. The intermediate and final polymers were characterized by gel permeation chromatography and NMR-H¹ spectrometry.     

Layer-by-layer films of enzymatically synthesized poly(aniline)/bacterial poly(γ-glutamic acid) for the construction of nanocapacitors

Poly(aniline) (PANi) and poly(γ-glutamic acid) (γ-PGA) have been synthesized by enzymatic catalysis and natural bacterial reactions, respectively. Layer-by-layer films have been prepared on glass or quartz slides by alternative immersions of the substrate in dilute solutions of γ-PGA and PANi, with several rinsing in between each deposition. UV-vis spectroscopy has been used to follow the evolution of the self-assembly process as well as to characterize the oxidative states of PANi. The linear dependence of the absorbance vs. the number of layers indicates a constant increase of thickness layer-by-layer. The morphology of the multilayer films, analyzed by atomic force microscopy, is granular type. Enzymatically synthesized PANi nanofilms present good electrical conductivity while γ-PGA acts as an insulating material. These differences in electrical properties and the possibility to obtain alternated multilayered films permit the construction of entirely “biological” nanocapacitors.     

Oxidative and photooxidative degradation of poly(acrylic acid)

The oxidative degradation of poly(acrylic acid) (PAA), a water soluble polymer, was studied at various temperatures with different concentrations of persulfates, potassium persulfate (KPS), ammonium persulfate (APS) and sodium persulfate (SPS). The photodegradation of PAA was also examined with APS as oxidizer. The degraded samples were analyzed for the time evolution of molecular weight distribution by gel permeation chromatography. A theoretical model based on the continuous distribution kinetics was developed that accounted for the polymer degradation and the dissociation of persulfate. The rate coefficients for the oxidative and photooxidative degradation of PAA were determined from the parametric fit of the model with experimental data. The rate of degradation increased with increasing amount of persulfate in both oxidative and photooxidative degradation. The rate of degradation also increased with increasing temperature in the case of oxidative degradation.     

Fluorescence staining and confocal laser scanning microscopy study of hydrogen-bonded poly(vinylpyrrolidone)/poly(acrylic acid) film

Poly(vinylpyrrolidone) (PVPON) and poly(acrylic acid) (PAA) were layer-by-layer (LBL) assembled to prepare the thin films based on hydrogen-bonding complexation. The hydrogen-bonded PVPON/PAA films were incubated in acidic, neutral and basic vapors separately. To study the morphologies after incubation, the films were stained by pH-sensitive fluorescent dyes using chemical and physical ways, and investigated with confocal laser scanning microscope (CLSM). The chemical way (labeling) was covalently linking fluoresceinamine (FAM) to some monomer units of PAA while the physical way was adsorbing rhodamine B (RB) molecules from dilute solution. Atomic force microscope (AFM) was combined with CLSM to find that after incubation in neutral or basic vapor the hydrogen-bonded PVPON/PAA films form porous structure and the pores are through the whole film.     

Photo-grafting Poly(acrylic acid) onto Poly(lactic acid) Chains in Solution

Poly(lactic acid)(PLA)is one of the most important bio-plastics,and chemical modification of the already-polymerized poly(lactic acid)chains may enable optimization of its material properties and expand its application areas.In this study,we demonstrated that poly(lactic acid)can be readily dissolved in acrylic acid at room temperature,and acrylic acid can be graft-polymerized onto poly(lactic acid)chains in solution with the help of photoinitiator benzophenone under 254 nm ultraviolet(UV)irradiation.Similar photo-grafting polymerization of acrylic acid(PAA)has only been studied before in the surface modification of polymer films.The graft ratio could be controlled by various reaction parameters,including irradiation time,benzophenone content,and monomer/polymer ratios.This photo-grafting reaction resulted in high graft ratio(graft ratio PAA/PLA up to 180%)without formation of homopolymers of acrylic acid.When the PAA/PLA graft ratio was higher than 100%,the resulting PLA-g-PAA polymer was found dispersible in water.The pros and cons of the photo-grafting reaction were also discussed.     

Pervaporation of alcohol-toluene mixtures through polymer blend membranes of poly(acrylic acid) and poly(vinyl alcohol)

Homogeneous membranes were prepared by blending poly(acrylic acid) with poly(vinyl alcohol). These blend membranes were evaluated for the selective separation of alcohols from toluene by pervaporation. The flux and selectivity of the membranes were determined both as a function of the blend composition and of the feed mixture composition. The results showed that a polymer blending method could be very useful to develop new membranes with improved permselectivity. The pervaporation properties could be optimized by adjusting the blend composition. All the blend membranes tested showed a decrease in flux with increasing poly(vinyl alcohol) content for both methanol—toluene and ethanol—toluene liquid mixtures. The alcohols permeated preferentially through all tested blend membranes, and the selectivity values increased with increasing poly(vinyl alcohol) content. The pervaporation characteristics of the blend membranes were also strongly influenced by the feed mixture composition. The fluxes increased exponentially with increasing alcohol concentration in the feed mixtures, whereas the selectivities decreased for both liquid mixtures.     

MMTCA recognition by molecular imprinting in interpenetrating polymer network hydrogels based on poly(acrylic acid) and poly(vinyl alcohol)

A novel IPN hydrogel designed to recognize MMTCA is prepared by applying the molecular-imprinting method. The IPN is characterized by FT-IR, DSC, and SEM. Langmuir analysis shows that an equal class of adsorption is formed in the hydrogel. The adsorption equilibrium constant and the maximum adsorption capacity are evaluated, and the effect of the pH on MMTCA adsorption is discussed. The selectivity of the imprinted polymer for MMTCA is studied in aqueous solutions of MMTCA/aspirin/riboflavin. The results suggest that the MMTCA-imprinted polymer shows superior selectivity for MMTCA as compared to riboflavin and aspirin. The reproducibility of the imprinted polymer to MMTCA is also studied.     

基于聚(2-甲基-2-噁唑啉)和聚丙烯酸的混合刷在毛细管电泳在线富集溶菌酶中的应用

制备了一种对溶菌酶具有可控吸附性能的混合刷涂层毛细管,用于毛细管电泳在线富集溶菌酶以提高其检测灵敏度。首先,分别通过阳离子开环聚合和可逆加成-断裂链转移（RAFT）聚合合成聚（2-甲基-2-噁唑啉）（PMOXA）和聚丙烯酸（PAA）,然后将甲基丙烯酸缩水甘油酯（GMA）分别与PMOXA和PAA通过自由基共聚和RAFT聚合合成出聚（2-甲基-2-噁唑啉）-r-甲基丙烯酸缩水甘油酯（PMOXA-r-GMA）和聚丙烯酸-b-聚甲基丙烯酸缩水甘油酯（PAA-b-PGMA）。将PMOXA-r-GMA和PAA-b-PGMA的混合溶液以一定比例加入到毛细管内,通过加热即可制备出基于PMOXA和PAA的混合刷涂层毛细管。X射线光电子能谱（XPS）对毛细管原材料的表面组成研究结果表明,当混合溶液质量浓度为20 g/L、PMOXA-r-GMA和PAA-b-PGMA质量比为1：1时,所得涂层中羧基的含量随着PAA链长的增加而增加;异硫氰酸荧光素标记溶菌酶（FITC-溶菌酶）吸附实验结果显示,通过改变环境的pH和离子强度（I）可以调控涂层毛细管对溶菌酶的吸附和释放,在pH 7（I=10^-5mol/L）条件下,毛细管可以吸附大量的溶菌酶,当条件变为pH 3（I=10^-1mol/L）时,吸附的溶菌酶可以被释放出来。将这种具有溶菌酶可控吸附性能的涂层毛细管用于毛细管电泳在线富集溶菌酶,当PAA链长是PMOXA链长的2.2倍时,溶菌酶的灵敏度增强因子为17.69,检出限为8.7×10^-5g/L;同一天内对溶菌酶连续测定5次以及连续测定5天,峰面积的日内、日间相对标准偏差（RSD）分别为2.9%和4.1%,迁移时间的日内、日间RSD分别为0.9%和2.1%。涂层的制备只需一步,简单易行,而且涂层具有很好的稳定性。本研究为毛细管电泳分析痕量蛋白质提供了一种简单有效的方法。     

Complexation of sequence-ordered methacrylic acid copolymers with poly(4-vinylpyridine)

The complexation of three kinds of sequence-ordered acid (co)polymers with a base homopolymer was studied. The acid polymers used are poly(methacrylic acid) 1 , alternating (1:1) ethylene-methacrylic acid copolymer 2 , and periodic (2:1) ethylene-methacrylic acid copolymer 3 , and the base polymer is poly(4-vinylpyridine) 4. When mixing a methanol solution of 1, 2 , or 3 with that of 4 (0.1 M of each functional group), precipitate was formed immediately for all polymer pairs. All the precipitates contained carboxyl and pyridyl groups in ca. 1:1 molar ratio and showed IR spectra indicating the hydrogen bonding between carboxyl and pyridyl groups. When mixing dilute methanol solutions (10⁻⁴M) of the above polymer pairs, no precipitation was observed, but the extinction coefficient (ϵ_B) at 255 nm of pyridyl groups in 4 was found to increase with an increasing acid polymer concentration. This is ascribed to hydrogen bonding between carboxyl and pyridyl groups in methanol. Based on the ϵ_B variation, the order of complexation constants for acid/base polymer pairs was estimated as follows: 1/4 pair ∼ 2/4 pair ≫ 3/4 pair. © 1996 John Wiley & Sons, Inc.     

Potentiometric titration behavior of poly(acrylic acid) within a cross-linked polymer network having amide groups

This study aimed to investigate the effect of COOH group distribution within a polymer network having amide groups, with which the COOH could form hydrogen bonds. We employed here two polyelectrolyte gels composed of N-isopropylacrylamide (NIPA) networks, either copolymerized with acrylic acid (AA) or within which poly(acrylic acid) (PAA) was entrapped. Both gels (AA–NIPA ∼ 1:4 mol/mol) were prepared by aqueous red-ox polymerization with N,N’-methylenebisacrylamide as the cross-linker. Finely divided gels in NaCl solutions (0.025 and 0.1 M) were titrated with NaOH and back-titrated with HCl at 25 °C. The results of the copolymer gel (CG) agreed well with those of a linear copolymer and a nanoscale gel which had a similar AA content to CG. However, marked differences were observed in the titration behaviors of the AA-copolymerized and PAA-entrapped gels, mainly due to the hydrogen bonding between the entrapped PAA chain and its surrounding NIPA network.     

Modification and characterization of semi-crystalline poly(vinyl alcohol) with interpenetrating poly(acrylic acid) by UV radiation method for alkaline solid polymer electrolytes membrane

Semi-crystalline poly(vinyl alcohol) was modified by UV radiation with acrylic acid monomer to get interpenetrating poly(acrylic acid) modified poly(vinyl alcohol), PVAAA, membrane. The stability of various PVAAA membranes in water, 2 M CH₃OH, 2 M H₂SO₄, and 40 wt% KOH aqueous media were evaluated. It was found that the stability of PVAAA membrane is stable in 40 wt% KOH solution. The PVAAA membranes were characterized by differential scanning calorimetry, X-ray diffraction, and thermogravimetry analysis. These results show that (1) the crystallinity in PVAAA decreased with increasing the content of poly(acrylic acid) in the PVAAA membranes. (2) The melting point of the PVAAA membrane is reduced with increasing the content of poly(acrylic acid) in the membrane. (3) Three stages of thermal degradation were found for pure PVA. Compared to pure PVA, the temperature of thermal degradation increased for the PVAAA membrane. The various PVAAA membranes were immersed in KOH solution to form polymer electrolyte membranes, PVAAA-KOH, and their performances for alkaline solid polymer electrolyte were conducted. At room temperature, the ionic conductivity increased from 0.044 to 0.312 S/cm. The result was due to the formation of interpenetrating polymer chain of poly(acrylic acid) in the PVAAA membrane and resulting in the increase of charge carriers in the PVA polymer matrix. Compared to the data reported for different membranes by other studies, our PVAAA membrane are highly ionic conducting alkaline solid polymer electrolytes membranes.     

Ion-specific swelling behavior of uncharged poly(acrylic acid) gel

The ion-specific swelling behavior of poly(acrylic acid) (PAA) gel prepared by -ray irradiation was investigated as a function of salt concentration in the presence of 0.01 M HCl. The anion specificity for the swelling ratio was similar to that for many kinds of hydrogels, i.e., Cl^–<Br^–<NO₃ ^–<I^–, while the cation specificity proved to be rather unusual, i.e., Mg²⁺<Ca²⁺<Li⁺<Na⁺<K⁺<Cs⁺. In order to find any differences in the hydration of uncharged PAA from that of other polymers having typical polar groups, the hydrogen-bonding hydrations on the relevant polar groups were compared for small molecule analogues with an ab initio molecular orbital calculation. According to the results, the marked deswelling of PAA gel in the presence of strongly hydrated cations was ascribed to the unfavorable hydration to the acidic proton of PAA due to the reduced availability of water oxygen as well as to the destabilization of hydrophobic hydration developing around the uncharged PAA.     

ipso-Bromination/iodination of arylboronic acids: Poly(4-vinylpyridine)-Br2/I2 complexes as safe and efficient reagents

Poly(4-vinyl pyridine) supported bromine/iodine complexes were prepared and probed for ipso-bromination/iodination of arylboronic acids. These solid complexes with catalytic amount of additive are found to be safe and efficient reagent system for the ipso-bromination/iodination. The reaction occurs under mild conditions and tolerates various functional groups resulting in products with high selectivity and yields.     

Needleless electrospinning of poly(acrylic acid) superabsorbent: Fabrication,characterization and swelling behavior

In this work, nanofibrous hydrogel has been fabricated from needleless electrospinning of Poly(acrylic acid) (PAA) in an aqueous solution with different concentrations. First, all solution samples were characterized for pH, surface tension, conductivity and viscosity. Next, electrospinnability of the PAA-water dope solution was investigated using the needleless electrospinning technique under constant conditions. Results indicated that the PAA-water solution was not electrospinnable. Therefore, the neutralization of carboxylic groups in the PAA chemical structure using the NaOH solution was investigated to enhance the PAA electrospinnability. Morphology observation revealed that the fiber diameters ranged from 40 to 250 nm and increased with increasing the solution concentrations. Increasing the neutralization degree (10%, 15% and 20% with 50 wt% NaOH solution) led to increase the dope viscosity and conductivity. The resultant nanofibers could be rendered water-insoluble by incorporating 1,4-butanediol diglycidyl-ether in the PAA-water dope solution, then heat-induced crosslinking was performed using a microwave at different curing times (1–5 min) and temperatures (45–105 °C). The nanofibrous hydrogel mat was then characterized by FTIR. The resulting nanofibrous hydrogel showed remarkable water absorption capacity up to 17,000% and 51,000% (within 15 min) in the standard saline solution and distilled water, respectively.