HPMA/OMMT和HPMA/CPMI/OMMT纳米复合材料的制备与表征

通过甲基丙烯酸羟丙酯(HPMA)单体与N-(4-羧基苯基)马来酰亚胺(CPMI)单体在有机蒙脱土(OMMT)中经原位插层自由基聚合反应制备了聚合物-无机纳米复合材料.OMMT由钠基蒙脱土通过十六烷基溴化铵插层处理制备.通过XRD和TEM对复合材料结构进行了表征,证实HPMA单体和HPMA/CPMI共单体在OMMT中原位插层共聚得到的复合材料均为剥离型纳米复合材料.OMMT含量为3 wt%的PolyHPMA/OMMT纳米复合材料起始分解温度为250℃,比相应的纯聚合物的热分解温度提高30℃.随着OMMT含量的增加,热分解温度进一步提高.但在测试温度范围内,PolyHPMA/OMMT纳米复合材料均没有出现明显的玻璃化转变温度.     

Nanostructure vs. microstructure: Morphological and thermomechanical characterization of poly(l-lactic acid)/layered silicate hybrids

Nano- and micro-composites of poly(l-lactic acid) (PLLA) with various loadings of natural and hexadecylamine-modified montmorillonite were prepared by the solvent casting method to study the effect of nanostructure on the thermomechanical properties of the hybrid materials. The changes on structure and surface of montmorillonite, induced by the ion-exchange modification process, were characterized by X-ray diffraction (XRD) analysis and zeta-potential determination, while the morphology of the hybrids and the dispersion of the clay into the polymer matrix were examined by XRD, transmission electron microscopy and atomic force microscopy. The results showed that, although at low clay content exfoliation dominates, for filler loadings greater than 5 wt% both exfoliation and intercalation of the clay filler are observed. Thermal degradation studies of the materials produced using thermogravimetry revealed the introduction of a small amount of organo-modified silicate significantly improves their thermal stability. Differential scanning calorimetry showed the thermal behavior of the polymer matrix strongly depends on the nature and content of the silicate filler. Scanning electron microscopy of the deformed surfaces affirmed a different deformation process mechanism between the two types of composites.     

Morphology and elastic modulus of novel poly[oligo(ethylene glycol) diacrylate]‐montmorillonite nanocomposites

Novel thermosetting poly[oligo(ethylene glycol) diacrylate]‐sodium montmorillonite nanocomposites containing a range of clay volume fractions were prepared by an in situ polymerization method. X‐ray diffraction showed that the basal plane spacing of the clay was increased to approximately 1.7 nm regardless of clay volume fraction. Transmission electron microscopy confirmed the basal spacing and intercalated structure. The elastic moduli of the composites were measured using ultrasonic pulse‐echo equipment. The results show that the Young's modulus and shear modulus increase with nominal clay volume fraction up to 0.22, and are in good agreement with the well‐established Christensen method and derived Hashin–Shtrikman bounds for conventional composites provided that the true volume fraction of clay reinforcement filler is calculated. At low clay volume fractions, the composites were transparent. When the nominal clay volume fraction was further increased, cracks and porous surfaces appeared, as observed by scanning electron microscopy. These defects decreased the elastic modulus, indicating an upper limit for clay additions in this preparation route. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1785–1793, 2005     

Study on ablative properties and mechanisms of hydrogenated nitrile butadiene rubber (HNBR) composites containing different fillers

The ablative properties of hydrogenated nitrile butadiene rubber (HNBR) composites filled with fumed silica, organically modified montmorillonite (OMMT), or expanded graphite (EG) were examined. The HNBR/OMMT composite has the lowest linear ablation rate and the highest mass ablation rate and does not tend to be carbonized. On the other hand, the HNBR/EG composite has the highest linear ablation rate and the lowest mass ablation rate, and is prone to carbonization. The ablative properties of the HNBR/silica composite are between those of HNBR/OMMT and HNBR/EG. From the viewpoint of thermal shielding capability, the HNBR/OMMT has the best ablation resistance. Thermogravimetric analysis (TGA) on different HNBR composites indicated that the filler type has no significant effect on the thermal stability of the composites. To understand the ablation mechanisms, the char layers of different HNBR composites after ablation experiments were characterized by scanning electron microscopy (SEM), energy disperse X-ray spectroscopy (EDS), and wide-angle X-ray diffraction (WAXD). The results showed that the porosity in the char layers of the HNBR/OMMT composite was the highest and the corresponding structure was the loosest of the three composites. The montmorillonite (MMT) dispersed in HNBR experienced phase transition, melting and vaporization when exposed to the flame with the temperature over 2000 °C. Fumed silica only melted at such situation. On the other hand, the EG kept their original crystalline structures after the ablation test. Based on these results, the effect of the filler type on the ablation mechanisms of the HNBR composites was discussed.     

Effect of organo‐modified montmorillonite on flame retardant poly(1,4‐butylene terephthalate) composites

In this paper, the effect of organo‐modified montmorillonite (OMMT) on a novel intumescent flame retardant (IFR) system was studied in poly(1,4‐butylene terephthalate) (PBT) composites containing microencapsulated ammonium polyphosphate (MAPP) and melamine cyanurate (MC). Nanocomposite morphology was characterized by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Thermal decomposition analysis was studied via thermogravimetric analysis (TGA). Combustion behavior was investigated by microcombustion calorimeter (MCC), limited oxygen index (LOI), and UL‐94 test. Residues obtained after samples treated in muffle furnace at 500°C under air condition for 10 min were analyzed through X‐ray powder diffraction (XRD) and scanning electron microscopy (SEM). It was found that the addition of OMMT improved the flame retardancy of PBT/IFR composites significantly. A mass of microcomposite structure particles formed in the heating or combustion process of PBT/IFR/OMMT nanocomposites were found for the first time in the SEM images, which is strong evidence to confirm the migration or accumulation of montmorillonite and carbonaceous‐silicate materials during the heating or combustion process. Copyright © 2010 John Wiley & Sons, Ltd.     

Mechanical,Thermal and Morphological Behaviors of Castor Oil Based PU/PS Interpenetrating Polymer Network-Metakaolin Composites

The meta kaolin (MK) clay particulate filler with different weight ratios viz., 0, 5, 10, 20 and 30 wt% were incorporated into castable polyurethane (PU)/polystyrene (PS) (90/10) interpenetrating polymer network (IPN). The effects of MK particulate filler loading on the mechanical and thermal properties of PU/PS (90/10) IPN composites have been studied. From the tensile behavior, it was noticed that a significant improvement in tensile strength and tensile modulus as an increase in MK filler content. Thermogravimetric analysis (TGA) data reveals the marginal improvement in thermal stability after incorporation of MK filler. TGA studies of the IPN composites have been performed in order to establish the thermal stability and their mode of thermal degradation. It was found that degradation of all composites takes place in two steps. Degradation kinetic parameters were obtained for the composites using three mathematical models. Tensile fractured composite specimens were used to analyze the morphology of the composites by scanning electron microscopic (SEM) technique.     

Effect of extrusion and photo-oxidation on polyethylene/clay nanocomposites

Polyethylene (a 1:1 blend of m-LLDPE and z-LLDPE) double layer silicate clay nanocomposites were prepared by melt extrusion using a twin screw extruder. Maleic anhydride grafted polyethylene (PEgMA) was used as a compatibiliser to enhance the dispersion of two organically modified monmorilonite clays (OMMT): Closite 15A (CL15) and nanofill SE 3000 (NF), and natural montmorillonite (NaMMT). The clay dispersion and morphology obtained in the extruded nanocomposite samples were fully characterised both after processing and during photo-oxidation by a number of complementary analytical techniques. The effects of the compatibiliser, the organoclay modifier (quartenary alkyl ammonium surfactant) and the clays on the behaviour of the nanocomposites during processing and under accelerated weathering conditions were investigated. X-ray diffraction, transmission electron microscopy (TEM), scanning electron microscopy (SEM), rheometry and attenuated reflectance spectroscopy (ATR-FTIR) showed that the nanocomposite structure obtained is dependent on the type of clay used, the presence or absence of a compatibiliser and the environment the samples are exposed to. The results revealed that during processing PE/clay nanocomposites are formed in the presence of the compatibiliser PEgMA giving a hybrid exfoliated and intercalated structures, while microcomposites were obtained in the absence of PEgMA; the unmodified NaMMT-containing samples showed encapsulated clay structures with limited extent of dispersion in the polymer matrix. The effect of processing on the thermal stability of the OMMT-containing polymer samples was determined by measuring the additional amount of vinyl-type unsaturation formed due to a Hoffman elimination reaction that takes place in the alkyl ammonium surfactant of the modified clay at elevated temperatures. The results indicate that OMMT is responsible for the higher levels of unsaturation found in OMMT-PE samples when compared to both the polymer control and the NaMMT-PE samples and confirms the instability of the alkyl ammonium surfactant during melt processing and its deleterious effects on the durability aspects of nanocomposite products. The photostability of the PE/clay nanocomposites under accelerated weathering conditions was monitored by following changes in their infrared signatures and mechanical properties. The rate of photo-oxidation of the compatibilised PE/PEgMA/OMMT nanocomposites was much higher than that of the PE/OMMT (in absence of PEgMA) counterparts, the polymer controls and the PE–NaMMT sample. Several factors have been observed that can explain the difference in the photo-oxidative stability of the PE/clay nanocomposites including the adverse role played by the thermal decomposition products of the alkyl ammonium surfactant, the photo-instability of PEgMA, unfavourable interactions between PEgMA and products formed in the polymer as a consequence of the degradation of the surfactant on the clay, as well as a contribution from a much higher extent of exfoliated structures, determined by TEM, formed with increasing UV-exposure times.     

Evaluation of activation energy conformity derived from model-free non-isothermal predictions and Arrhenius isothermal results

Organically modified montmorillonite (OMMT) was used as synergist to enhance the flame-retardant and mechanical properties of poly(butylene succinate)/intumescent flame retardant (PBS/IFR) composites. The flame-retardant, thermal degradation and combustion properties of PBS and its flame-retardant composites were characterized by limiting oxygen index (LOI) test, vertical burning (UL-94) test, thermogravimetric analysis, cone calorimeter and scanning electron microscopy, respectively. The results indicate that PBS/IFR composites exhibit excellent flame retardance when OMMT is at an appropriate content. PBS/IFR composite with 20 wt% IFR and 1.5 wt% OMMT has an LOI of 40.1% and can pass the UL-94 V0 rating. The synergistic effect between OMMT and IFR on the flame-retardant properties of PBS depends on the content of OMMT, and excessive OMMT diminish this synergistic effect. The possible flame-retardant mechanism of OMMT on PBS/IFR composite is proposed. The results of mechanical test also indicate that OMMT can effectively increase the notched impact strength of PBS/IFR composites.     

Study of elastomeric polyurethane nanocomposites prepared from grafted organic–montmorillonite

4,4′-Diphenylmethane diisocyanate (MDI) was grafted on to organic–montmorillonite (OMMT) by reaction between hydroxyl groups (−OH) on surface of the montmorillonite and the isocyanate groups (−NCO) of MDI, thus forming grafted organic–montmorillonite (MOMMT). Intercalated nanocomposites based on polyurethane (PU) and MOMMT were prepared by solution intercalation technology. The interface interaction of PU/MOMMT nanocomposites was better than that of PU/MMT composites. The tensile strength, elongation at break, and tear strength of the PU/MOMMT nanocomposites increased for MOMMT content up to 5% w/w, and then decreased with further increase in MOMMT content. At the same filler content, the tensile strength and tear strength of PU/MOMMT nanocomposites were higher than those of PU/OMMT nanocomposites, whereas the elongations at break of PU/MOMMT nanocomposites were smaller than those of PU/OMMT nanocomposites. The initial temperatures of weight loss of PU/MOMMT nanocomposites were lower than for PU/MMT composites in the first step of thermal degradation, whereas in the second step initial temperatures of weight loss were higher for PU/MOMMT nanocomposites.     

Ball milling: An effective technique for the preparation of exfoliated clay filled unsaturated polyester toughened epoxy nanocomposite

This paper investigates the possibility of improving the mechanical and thermal properties of epoxy and unsaturated polyester toughened epoxy resins through the dispersion of octadecyl ammonium ion-exchanged montmorillonite (organoclay) through exfoliated mechanism. The nanocomposites prepared are characterized for their structural change and studied for their crystallite size, mechanical, thermal and water absorption (hydrophilicity) properties. The mechanical data indicates significant improvement in the flexural and tensile properties over the neat epoxy and UP-epoxy matrix according to the percentage content of organoclay. The thermal behavior too shows noticeable enhancement in glass transition temperature T _g and high thermal stability. Hydrophilicity of all the composites decreases irrespective of the concentration of organoclay on the epoxy and UP-epoxy matrices. The homogeneous morphology of epoxy and UP toughened epoxy nanocomposite hybrid systems is ascertained using scanning electron microscope (SEM). X-ray results point out that the cetyl ammonium modified clay filled composites exhibited the exfoliated structure.     

Synergism between flame retardant and modified layered silicate on thermal stability and fire behaviour of polyurethane nanocomposite foams

Synergy in flame retardancy of polyurethane foams between phosphorus-based flame retardant (aluminium phosphinate) and layered silicates has been investigated. We used pristine montmorillonite as well as ammonium modified clay (commercially available) and diphosphonium modified clay, which were synthesised by the intercalation of the quaternary diphosphonium salt according to a procedure reported here. The morphology of the foams was characterised through X-ray diffraction (XRD), while thermal properties were characterised by oxygen index test, cone calorimeter and thermogravimetric analysis (TGA). The morphological characterisation showed that pristine and diphosphonium modified clays are almost slightly intercalated, while ammonium modified one is very well dispersed. The results of thermal characterisation showed that in the presence of phosphinate enhancements of oxygen index, fire behaviour, measured by cone calorimeter, and thermal stability have been achieved. Phosphinate is therefore an efficient flame retardant for polyurethane foams and its flame retardancy action takes place in both condensed and gas phases. Pristine and ammonium modified layered silicate bring some enhancements of thermal stability while having no important effect in decreasing peak heat release rate (PHRR) and total heat evolved (THE) when used in conjunction with phosphinate; their main advantage is related to the enhancement of compactness of the char layer formed. Diphosphonium clay is instead effective in further improving the fire behaviour of the foams because of the flame retardancy action of phosphonium: both PHRR and THE were decreased. The analysis of cone calorimeter data showed that clays act through physical effect constituting a barrier at the surface which is effective in preventing or slowing the diffusion of volatiles and oxygen, while phosphinate and phosphonium are more effective owing to their combined action in both condensed and gas phases.     

本质阻燃聚苯乙烯/蒙脱土纳米复合物的制备及性能

通过原位聚合法制备了本质阻燃聚苯乙烯[P(St-co-AEPPA)]/有机改性蒙脱土(OMMT)纳米复合物[P(St-co-AEPPA)/OMMT], 并用普通聚苯乙烯/有机改性蒙脱土(PS/OMMT)复合物作为对比实验, 研究了含磷、氮单体丙烯酸羟乙基-苯氧基-二乙基磷酰胺(AEPPA)和OMMT等添加物对本质阻燃聚苯乙烯性能的影响.用X射线衍射仪(XRD)和透射电子显微镜(TEM)分析了复合材料的结构与形貌, 并对OMMT在基体中的分散机理进行了讨论.用差示扫描量热仪(DSC)、热重分析(TGA)和微型量热仪(MCC)研究了材料的热性能和燃烧性能.结果表明, AEPPA和OMMT能够显著提高基体的热稳定性和阻燃性.     

An assessment of the role of morphology in thermal/thermo-oxidative degradation mechanism of PP/EVA/clay nanocomposites

In this study, morphological properties of polypropylene (PP)/ethylene vinyl acetate copolymer (EVA) (75/25 wt/wt) blend-based nanocomposites containing various amounts of organically modified montmorillonite (OMMT) were primarily investigated. The incorporation of compatibilizer into nanocomposites decreased EVA droplet size in PP matrix while increasing compatibilizer/OMMT ratio showed a dual behavior with respect to the variations of OMMT interlayer spacing. By a rough estimation it was found that at EVA droplet size of D_n = 0.43 μm, the highest OMMT interlayer spacing would be acheived. Increasing D_n had a negative effect on the OMMT interlayer spacing. Activation energy of thermal/thermo-oxidative degradation based on Flynn model was obtained. Isothermal degradation test was also performed and desired temperature range for predicting degradation behavior was obtained by means of a free prediction model. An attempt was made to establish a correlation between morphological and thermal/thermo-oxidative parameters and also charred residue morphology. A mechanism for degradation process was proposed according to the changes of chemical bonds during the degradation process probed by FTIR analysis.     

Preparation and Barrier Properties of Chitosan-Layered Silicate Nanocomposite Films

Summary: In this study, chitosan nanocomposite films were prepared using a solvent-casting method by incorporation of an organically modified montmorillonite (Cloisite 10A). The effect of filler concentration on the water vapor permeability, oxygen permeability, mechanical and thermal properties of the composite films was evaluated. The structure of nanocomposites and the state of intercalation of the clay were characterized by XRD. The water vapor permeability of pure chitosan films was measured as a function of relative humidity (RH). It was found that the permeability value increased with an increase in RH. The water vapor and gas permeability values of the composite films decreased significantly with increasing filler concentration. Permeation data was fitted to various phenomenological models predicting the permeability of polymer systems filled with nanoclays as a function of clay concentration and aspect ratio of nanoplatelets. According to the XRD results, an increase in basal spacing was obtained with respect to pure clay for chitosan/clay nanocomposites. This demonstrated the formation of intercalated structure of clay in the polymer matrix. Tensile strength and elongation at break of the composites increased significantly with the addition of clay, however the thermal and color properties of the films were not much affected by the intercalation of clay into polymer matrix.     

The role of organoclay on the properties of Polymethylsilsesquioxane: A systematic study

In this study, an attempt is made to improve the properties of PMSQ, an organosilicone polymer which possesses distinguished properties, through an easy and facile route by the inclusion of organically modified montmorillonite clay. PMSQ-clay composites were prepared by solution blending of the components initially and then heat curing under load. The effect of clay content, varied at 5–40 wt.%, on mechanical, thermal and dynamic mechanical properties was evaluated and the optimum was obtained for 20%. Morphology investigation as well as microstructure analysis revealed intercalated to exfoliated morphology of PMSQ-clay composite. An appreciable improvement in mechanical properties of PMSQ, compressive strength and impact strength in particular, was achieved by clay inclusion up to 20%. The properties declined at ≥ 30% clay loading. The composites showed increased thermal stability compared to unmodified PMSQ up to 400 °C. Also, increase in clay content accelerated conversion to ceramic SiOC. PMSQ-clay composites exhibited good visco-elastic characteristics with higher T_g probably due to enhanced polymer-clay interactions. Thus, a simple and viable method to enhance the mechanical and thermal characteristics of PMSQ by way of preparing its composite with the reinforcing filler organoclay is demonstrated here.     

Organically modified montmorillonite as a synergist for intumescent flame retardant against the flammable polypropylene

Low flame retardant efficiency is a key bottleneck for currently available retardants against the flammable polypropylene (PP). Herein, the organically modified montmorillonite (OMMT) was utilized as a synergist for our previously reported intumescent flame retardant (IFR) that was constructed from ammonium polyphosphate (APP) and hyperbranched charring foaming agent (HCFA) to further enhance the retardant efficiency against PP. The resultant's combustion behavior was thoroughly investigated by cone calorimetry, limiting oxygen index (LOI), vertical burning test (UL‐94), and scanning electron microscopy (SEM). The results showed that 20% addition of IFR with OMMT showed a positive effect and improved the flame retardancy of the PP systems. Especially, addition of 2 wt% OMMT obviously increased the LOI values of PP systems with 20% total loading flame retardants from 29% to 31.5% and the samples meet V‐0 rating as well as the reduction of the heat release rate (HRR), total heat release (THR), CO₂, and CO production occurred. On the other hand, the SEM images were also revealed that OMMT initiated a dense and strong char on the surface of the material, which resulted in efficient flame retardancy of PP matrix during combustion. In addition, thermal degradation behavior discussed by thermogravimetric analysis (TGA) indicated that OMMT could improve the thermal stability of PP systems under high temperature, and promoted char residues of PP/IFR systems. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation,characterization and thermal behavior of poly(vinyl alcohol)/organic montmorillonite nanocomposites through solid-state shear pan-milling

In this study, the solid-state shear pan-milling was employed to prepare a series of polymer/layered silicate (PLS) nanocomposites. During the process of pan-milling at ambient temperature, poly(vinyl alcohol)/organic montmorillonite (PVA/OMMT) can be effectively pulverized, resulting in coexistence of intercalated and exfoliated OMMT layers. The obtained PLS nanocomposites were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). TEM analysis indicated that OMMT dispersed homogeneously in PVA matrix and XRD results illustrated that pan-milling had an obvious effect on increase in the interlayer spacing of OMMT, and resulted in coexistence of intercalated and exfoliated OMMT layers formed. Thermal gravimetric analysis showed that thermal stability of PVA was improved owing to the incorporation of OMMT. Thermal decomposition kinetics of PVA/OMMT nanocomposites with different milling cycles of OMMT was also studied. Two types of OMMT are chosen to compare the effect of hydrophilicity of OMMT on PVA/OMMT nanocomposites.     

Effect of Different Organic Modifiers on the Tensile Properties of PVC／EVA／Montmorillonite Composites

Poly (vinyl chloride)/ethylene-vinyl acetate/montmorillonite (PVC/EVA/OMMT) composites were prepared by melt blending method. Two kinds of montmorillonites were organically modified by trimethyloctadecyl ammonium and dimethyl bis (hydrogenated tallow) ammonium, respectively. The morphology and tensile properties of the resultant composites were discussed in terms of the modifier type and OMMT content. The PVC/EVA/OMMT composites have intercalated structure, which is independent of the polarity of the modifiers, while the tensile properties show strong dependence on the modifier type. The OMMT modified by polar modifier gives higher tensile ductile and strength of PVC/EVA/OMMT composites.     

Preparation and rheological characterization of poly(n-butyl methacrylate)/montmorillonite composites

Intercalated nanocomposites constituted of poly(butyl methacrylate) (PBMA) as the matrix and an organically modified montmorillonite as the nanosize filler were prepared and rheologically characterized in detail. The rheological behavior of the composites showed dependence on both temperature and clay content. For composites of low clay contents, the steady shear viscosity showed a Newtonian plateau in the low shear rate region at low temperatures and the plateau was replaced by a shear-thinning curve when the temperature was raised. For composites of higher clay contents, strong shear-thinning behavior were observed at all shear rates and all temperatures. The viscoelastic data of the composites showed unusual terminal behavior of a decreasing terminal slope at low frequencies with increasing temperature and clay loading. X-ray diffraction spectra showed that annealing process at higher temperatures shifted the Bragg reflection peaks to a lower angle and broadened the peaks, which provided the evidence for the existence of a temperature-induced solid-like structure that was responsible for the shear thinning and the unusual terminal viscoelastic behavior.     

Influence of Fe‐MMT on crosslinking and thermal degradation in silicone rubber/clay nanocomposites

In this article, silicone rubber (SR)/clay nanocomposites were synthesized by a melt‐intercalation process using synthetic Fe‐montmorillonite (Fe‐MMT) and natural Na‐MMT which were modified by cetyltrimethyl ammonium bromide (CTAB). This study has been designed to determine if the presence of structural iron in the matrix can result in radical trapping and then enhance thermal stability, affect the crosslinking degree and elongation. The SR/clay nanocomposites were characterized by X‐ray diffraction (XRD) patterns and transmission electron microscopy (TEM). Exfoliated and intercalated nanocomposites were obtained. Thermo gravimetric analysis (TGA) and mechanical performance were applied to test the properties of the SR/clay nanocomposites. The presence of iron significantly increased the onset temperature of thermal degradation in SR/Fe‐MMT nanocomposites. The thermal stability, gel fraction and mechanical property of SR/Fe‐MMT were different from the SR/Na‐MMT nanocomposites. So the iron not only in thermal degradation but in the vulcanization process acted as an antioxidant and radicals trap. Copyright © 2006 John Wiley & Sons, Ltd.