Rheological behaviour of irradiated wound dressing poly(vinyl pyrrolidone) hydrogels

The use of hydrogels as biomaterials has increased lately. Poly(vinyl pyrrolidone) (PVP) is an example of polymer hydrogels applied for the synthesis of hydrogel to be used in different biomedical applications. This paper describes a study on rheological properties of PVP hydrogels obtained by gamma radiation techniques. PVP hydrogels were obtained by gamma radiation of PVP water solutions with different radiation doses. It was studied the influence of additives such as poly(ethylene glycol) (PEG), poly(ethylene oxide) (PEO) and glycerol on the rheological behaviour of the gel. The rheological behaviour of hydrogel samples was characterized by measuring the shear storage modulus (G′) under dynamic shear loading. Besides this, sterility and cytotoxicity tests were performed. The study on rheological behaviour of hydrogels showed that G′ of PVP gels change according to the additive used. Glycerol increases the fluidity of the gel. The influence of PEG depends on the amount and on its molecular mass. The increase on PEG amount and molecular mass cause a decrease of G′ and an increase in the crosslinking density of PVP hydrogel network. The use of high molecular weight PEO allows the increase of the elasticity of the PVP gels.     

Novel antibacterial fibers of quaternized chitosan and poly(vinyl pyrrolidone) prepared by electrospinning

The preparation of continuous defect-free fibers from quaternized chitosan derivative (QCh) has been achieved by electrospinning of mixed aqueous solutions of QCh with poly(vinyl pyrrolidone) (PVP). The average fiber diameter significantly decreases from 2800 to 1500 nm on increasing the polyelectrolyte content. In order to impart to QCh/PVP electrospun fibers stability to water and water vapor, the fibers have been crosslinked by incorporation of photo-crosslinking additives into QCh/PVP spinning solutions and subsequent UV irradiation of the electrospun fibers. Photo-crosslinked QCh-containing electrospun mats show high antibacterial activity against the Gram-positive bacteria Staphylococcus aureus and Gram-negative bacteria Escherichia coli.     

Electrospinning and characterization of medium-molecular-weight poly(vinyl alcohol)/high-molecular-weight poly(vinyl alcohol)/montmorillonite nanofibers

Submicron fibers of medium-molecular-weight poly(vinyl alcohol) (MMW-PVA), high-molecular-weight poly(vinyl alcohol) (HMW-PVA), and montmorillonite clay (MMT) in aqueous solutions were prepared by electrospinning technique. The effect of HMW-PVA and MMT on the morphology and mechanical properties of the MMW-PVA/HMW-PVA/MMT nanofibers were investigated for the first time. Scanning electron microscopy, viscometer, tensile strength testing machine, thermal gravimetric analyzer (TGA), and transmission electron microscopy (TEM) were utilized to characterize the PVA/MMT nanofibers morphology and properties. The MMW-PVA/HMW-PVA ratios and MMT concentration played important roles in nanofiber's properties. TEM data demonstrated that exfoliated MMT layers were well distributed within nanofibers. It was also found that the mechanical property and thermal stability were increased with HMW-PVA and MMT contents.     

Effect of temperature on the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions

In this work the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions were measured at 283.1–313.1 K. The expansion factor of polymer chain was calculated by use of the intrinsic viscosities data. The thermodynamic parameters of polymer solution (the entropy of dilution parameter, the heat of dilution parameter, theta temperature, polymer–solvent interaction parameter and second osmotic virial coefficient) were evaluated by temperature dependence of polymer chain expansion factor. The obtained thermodynamic parameters indicate that quality of water was decreased for solutions of poly(ethylene oxide), poly(vinyl pyrrolidone) and poly(ethylene oxide)/poly(vinyl pyrrolidone) blends by increasing temperature. Compatibility of poly(ethylene oxide)/poly(vinyl pyrrolidone) blends were explained in terms of difference between experimental and ideal intrinsic viscosity and solvent–polymer interaction parameter. The results indicate that the poly(ethylene glycol)/poly(vinyl pyrrolidone) blends were incompatible.     

聚乙烯吡咯烷酮/四氧化三铁复合纳米纤维的制备与表征

采用静电纺丝方法制备了聚乙烯吡咯烷酮/四氧化三铁复合纳米纤维, 并用透射电子显微镜(TEM)、X射线衍射(XRD)、热失重分析(TGA)和振动磁力分析进行了表征, 探讨了复合物的结构及其性能.     

Synthesis and characterization of poly(vinyl pyrrolidone)-capped bismuth nanospheres

Poly(vinyl pyrrolidone)-capped bismuth nanospheres were synthesized by a simple and convenient wet chemical method. In the process, bismuth nitrate was reduced by ethylene glycol in the presence of poly(vinyl pyrrolidone) (PVP) at 185 °C in air. PVP was used as a protecting agent to prevent oxidation of the sperical bismuth particles. PVP molecules were absorbed on the surface of bismuth nanospheres through the interaction of O–Bi bond which was confirmed by Fourier transform infrared (FT-IR) measurement. The thermal analysis shows the samples contained about 73 wt.% metallic bismuth. The optical absorption spectrum of poly(vinyl pyrrolidone)-capped bismuth nanosphere shows a strong absorption band at 275 nm.     

Interaction of collagen and poly(vinyl pyrrolidone) in blends

The interaction between collagen and poly(vinyl pyrrolidone) (PVP) in blends has been studied by viscometry, differential scanning calorimetry (DSC) and by Fourier transform infrared spectroscopy (FTIR). It was found that the amide A and amide I bands position in FTIR spectra of collagen were shifted after blending with PVP to higher wavenumbers. DSC measurements showed different melting temperature, glass transition temperature and enthalpy for the blends and for the single components. Viscosity measurements showed interaction between collagen and PVP also in a dilute water solution.The results have shown, that the interactions between collagen and PVP exist due to the strong interactions between the synthetic and biological component, mainly by hydrogen bonds. These interactions caused that collagen and PVP are miscible at molecular level. The blending of collagen with PVP may give the possibility of producing new materials for potential biomedical applications.     

A novel route to substituted poly(vinyl pyrrolidone)s via simple functionalization of 1-vinyl-2-pyrrolidone in the 3-position by ring-opening reactions

A general synthetic approach is described that allows to obtain novel 1-vinyl-2-pyrrolidone (VP) derivatives with different kinds of functional groups in its 3-position in a one-pot reaction. The strategy used to achieve this goal is the reaction of the carboxamide anion of 1-vinyl-2-pyrrolidone with cyclic precursors of these functionalities. While the driving force for the reactions of three-membered rings is their high annular tension, it is shown here that larger heterocycles can be opened with good yield when additional electron-withdrawing groups are present in the ring. This leads to VP with longer spacer groups between the functionality and the future polymeric main chain. Furthermore, the high versatility of this procedure is demonstrated by the preparation, for the first time, of VP modified with amine or sulfonic functionalities that allow to prepare the corresponding aminated and sulfonated PVPs.     

Interpolymer complexation and thermal behaviour of poly(styrene-co-maleic acid)/poly(vinyl pyrrolidone) mixtures

Polymer complexation between poly(styrene-co-maleic acid), (SMA28) and (SMA50) containing 28 and 50 mol% of maleic acid and poly(vinyl pyrrolidone) (PVP), has been investigated by differential scanning calorimeter (DSC), Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). All results showed that the ideal complex composition of SMA28/PVP and SMA50/PVP leads, respectively, to 2:1 and 1:1 mole ratio of interacting components.For the investigated systems, the T_g versus composition curve does not follow any of the usual proposed models for polymer blends. Withal, a new model proposed by Cowie et al. is used to fit the T_g data and it is found to reproduce the experimental results more closely. According to n and q obtained values, it seems reasonable to conclude that the inter-associated hydrogen bonds dominate in SMA28/PVP (2:1) complexes. This effect is corroborated by the FTIR study as evidenced by the high displacement of the specific bands and ionic interactions have been clearly identified. Finally, a thermogravimetric study shows that ionic interactions increase the thermal stability of these complexes.     

Bicomponent aligned nanofibers of N-carboxyethylchitosan and poly(vinyl alcohol)

Bicomponent nanofibers of N-carboxyethylchitosan (CECh) and poly(vinyl alcohol) (PVA) were obtained by electrospinning of mixed aqueous solutions. The electrospinning of CECh-containing nanofibers was enabled by the ability of PVA to form an elastically deformable entanglement network based on hydrogen bonds. The average diameters of the bicomponent fibers were in the range 100-420 nm. Water-resistant nanofibrous mats were obtained by thermal crosslinking at 100 °C for 10 h. Nanofibrous materials with 1D-, 1D-transversery or 3D fiber alignment were obtained depending on the type of the collector used.     

Photochemical stability of poly(vinyl pyrrolidone) in the presence of collagen

The photochemical stability of poly(vinyl pyrrolidone) (PVP) in the presence of 1%, 3% and 5% of collagen has been studied by UV-vis spectroscopy, Fourier transform infrared spectroscopy (FTIR), thermogravimetry analysis (TG) and derivative thermogravimetry (DTG). Surface properties have been studied by contact angle measurements. PVP samples and samples containing 1%, 3% and 5% of collagen were irradiated with UV light of wavelength λ = 254 nm in air for up to 24 h. The amount of gel created during UV irradiation was estimated.PVP in the presence of 1%, 3% and 5% of collagen is less stable both thermally and photochemically. Collagen enhances photochemical processes leading to crosslinking of PVP. The contact angle measurements and values of surface free energy showed that the wettability of PVP films was changed by the addition of collagen and by UV irradiation. The increase of polarity of samples indicates an efficient photooxidation on the surface upon UV irradiation.     

聚乙烯醇/聚乙烯吡咯烷酮碱性复合膜的制备及其性能

通过在不同浓度KOH溶液中进行掺杂,制备出了聚乙烯醇/聚乙烯吡咯烷酮(PVA/PVP)碱性聚合物电解质膜.详尽考察了膜的组成、微观结构、热稳定性、离子电导率和甲醇吸收率.结果表明,PVA与PVP两者具有较好的相容性,当m(PVA)∶m(PVP)=1∶0.5时,膜断面致密、均匀,未发生大尺度相分离.PVP的混入可以极大提高复合膜的电导率和热稳定性.当m(PVA)∶m(PVP)=1∶1时,复合膜的电导率可达2.01×10-3 S.cm-1.PVA/PVP/KOH膜的甲醇吸收率随温度的升高没有明显变化,100℃时其甲醇吸收率仅为同条件下Nafion 115膜的1/4.这表明该复合膜有望作为一种新型的碱性直接甲醇燃料电池用固体电解质膜且可提高膜的使用温度.     

Thermal degradation of poly(vinyl chloride)/poly(ethylene oxide) blends: Thermogravimetric analysis

Thermal stability of poly(vinyl chloride)/poly(ethylene oxide) (PVC/PEO) blends has been investigated by thermogravimetric analysis (TGA) in dynamic and isothermal heating regime. PVC/PEO blends were prepared by hot-melt extrusion (HME). According to TG analysis, PEO decomposes in one stage, while PVC and PVC/PEO blends in two degradation stages. In order to evaluate the effect of PEO content on the thermal stability of PVC/PEO blends, different criteria were used. It was found that thermal stability of PVC/PEO blends depends on the blend composition. The interactions of blends components with their degradation products were confirmed. By using multiple heating rate kinetics the activation energies of the PVC/PEO blends thermal degradation were calculated by isoconversional integral Flynn–Wall–Ozawa and differential Friedman method. According to dependence of activation energy on degree of conversion the complexity of degradation processes was determined.     

高稳定性化学交联聚乙烯醇/聚乙烯吡咯烷酮碱性固体电解质膜

碱性固体电解质膜的稳定性是影响其在电化学领域应用的一个重要因素.本文在前期研究工作的基础上,通过直接共混和化学交联修饰制备出了聚乙烯醇/聚乙烯吡咯烷酮(PVA/PVP)碱性聚合物电解质膜.采用傅里叶变换红外(FTIR)光谱、热重分析(TGA)、扫描电镜(SEM)和交流阻抗等方法详细考察了复合膜的分子结构、热稳定性、化学稳定性、氧化稳定性和尺寸稳定性.红外光谱结果表明,PVP成功地混入聚合物基体中,在1672cm-1处表现出来自于PVP第I带C襒O的强吸收峰.TGA结果表明,提高掺杂的KOH溶液浓度对PVA/PVP碱性膜的热稳定性没有明显影响.SEM分析结果表明,复合膜经高温、高浓度碱(80℃,10mol·L-1)处理后,其断面结构仍致密均匀,未出现类似小孔等膜降解情况,此时膜电导率(1.58×10-3S·cm-1)相比室温相同碱液时提高91.5%,表明PVA/PVP膜具有很好的耐碱化学稳定性.同时,PVA/PVP碱性膜表现出良好的抗氧化性,在60℃的3%和10%H2O2溶液中处理均没有观察到明显的质量损失,150h后仍能保持原膜质量的89%和85%.此外,由于膜内形成致密的内互交联网络结构,复合膜在水中800h之后也表现出很好的同向性和电导率稳定性.     

Electrospinning and characterization of poly(vinyl alcohol)/chitosan oligosaccharide/clay nanocomposite nanofibers in aqueous solutions

Submicron fibers of the composite of poly(vinyl alcohol) (PVA), chitosan oligosaccharide [COS, (1→4)2-amino-2-deoxy-β-d-glucose], and montmorillonite clay (MMT) were prepared using electrospinning method with aqueous solutions. Scanning electron microscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), thermal gravimetric analyzer, and tensile strength testing machine (Zwick) were utilized to characterize the PVA/COS/MMT nanofiber mats morphology and properties. The PVA/COS ratio and MMT concentration play important roles in nanofiber mat properties. XRD and TEM data demonstrated that exfoliated MMT layers were well-distributed within nanofiber. It was also found that the mechanical property and thermal stability were increased with COS and MMT contents.     

Intrinsic adhesion properties of poly(vinyl pyrrolidone) to pharmaceutical materials: humidity effect

Poly(vinyl pyrrolidone) (PVP) is widely used for bioengineering and pharmaceutical applications, and its adhesion characteristics are critical. When used as a binder in pharmaceutical granulation, it covers the resultant granules and governs their surface properties. The intrinsic adhesion forces of PVP toward common hydrophobic (magnesium stearate) and hydrophilic (lactose) pharmaceutical materials have been studied as a function of relative humidity (RH). The effect of RH on adhesion force was more significant for the PVP/hydrophilic material than the PVP/hydrophobic material. Adhesion was lowest between 20 and 40% RH, and it increased at RH above 40% and below 20%. This is likely to be due to the development of capillary and triboelectrification forces, respectively. In a nano-indentation experiment using a silicon tip at room temperature, the PVP surface underwent a glass transition at 70% RH. This result suggests that surface softening contributes to the increased PVP adhesion at RH above 70%. To adjust the adhesion properties of PVP, humidity control should be an essential part of research and development. Effect of humidity on the adhesion forces between PVP and lactose (LT) or magnesium stearate (MS).     

Interactions between cationic mixed micelles and poly(vinyl pyrrolidone)

 The conductances of trimethyltetradecylammonium bromide (TTAB) + trimethylhexa decylammonium bromide (HTAB) and TTAB + trimethyldodecylammonium bromide (DTAB) mixtures over the entire mole fraction range were measured in aqueous poly(vinyl pyrrolidone) (PVP) containing 1–10 wt% PVP at 30 °C. Each conductivity (κ) curve for the TTAB + HTAB mixtures showed two breaks corresponding to two aggregation processes over the whole mole fraction range, except in the case of pure TTAB, where a single break corresponding to the conventional critical micelle concentration (cmc) was observed. In the case of TTAB + DTAB mixtures, each κ curve at a particular mole fraction of TTAB showed only one break, which was quite close to a similar one in pure water. In TTAB + HTAB mixtures, the first break is called the critical aggregation concentration. It is close to the conventional cmc and is attributed to the polymer-free micelle formation, whereas the second break is due to the polymer-bound micellar aggregates. However, no polymer-bound micellar aggregation process was observed in the case of TTAB + DTAB mixtures. Therefore, the presence of micelle–PVP interactions in the TTAB + HTAB case have been attributed to the stronger hydrophobicity of HTAB or TTAB + HTAB micelles in comparison to that of single or mixed micelles of TTAB + DTAB mixtures. From the conductivity data, various micelle parameters in the presence of PVP have been computed and discussed in terms of micelle–polymer interactions. The mixing behavior of TTAB +  HTAB corresponding to the first break, and that of TTAB + DTAB mixtures in the presence of PVP, is close to ideal and is also identical to that in pure water. Received: 26 August 1999 Accepted: 6 November 1999     

High-performances membranes for pervaporation I. Poly(vinyl alcohol)–poly(N-vinyl pyrrolidone) blends

Dense membranes were prepared from poly(vinyl alcohol)–poly(N-vinyl pyrrolidone) (PVA–PVP) blends of different compositions and studied in swelling and dehydration by pervaporation of three organic solvents contaminated by 5 wt% water. The swelling generally increases with the PVP content. No extraction occurs in water–tetrahydrofuran (THF) and water–methyl ethyl ketone (MEK) mixtures. In ethanol containing 10 wt% of water, there is no extraction for blends containing less than 40 wt% PVP and an increasing extraction beyond this PVP content. The pervaporation flux of the water–ethanol mixture increases drastically at the same threshold whereas the water permselectivity falls to a low level. The values of the diffusion and permeability coefficients determined from transient permeation of the test water–ethanol mixture exhibit a similar sudden increase at the same PVP content threshold. This singular behavior of the blend membranes is interpreted by a strong affinity of the PVP component to ethanol, combined with a disappearance of crystallites in the blend at this threshold. Consequently the amorphous membrane can swell freely according to the affinity of the PVP component, leading to the observed behavior.     

Viscometric study of poly(vinyl chloride)/poly(vinyl acetate) blends in various solvents

The intermolecular interactions between poly(vinyl chloride) (PVC) and poly(vinyl acetate) (PVAc) in tetrahydrofuran (THF), methyl ethyl ketone (MEK) and N,N^′-dimethylformamide (DMF) were thoroughly investigated by the viscosity measurement. It has been found that the solvent selected has a great influence upon the polymer-polymer interactions in solution. If using PVAc and THF, or PVAc and DMF to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+THF) or (PVAc+DMF) is less than in corresponding pure solvent of THF or DMF. On the contrary, if using PVAc and MEK to form polymer solvent, the intrinsic viscosity of PVC in polymer solvent of (PVAc+MEK) is larger than in pure solvent of MEK. The influence of solvent upon the polymer-polymer interactions also comes from the interaction parameter term Δb, developed from modified Krigbaum and Wall theory. If PVC/PVAc blends with the weight ratio of 1/1 was dissolved in THF or DMF, Δb<0. On the contrary, if PVC/PVAc blends with the same weight ratio was dissolved in MEK, Δb>0. These experimental results show that the compatibility of PVC/PVAc blends is greatly associated with the solvent from which polymer mixtures were cast. The agreement of these results with differential scanning calorimetry measurements of PVC/PVAc blends casting from different solvents is good.     

模板法制备定向排列的聚乙烯吡咯烷酮纳米管簇

近年来,随着纳米科学的迅猛发展,对定向生长的纳米碳管、半导体、氧化物及金属纳米线、管等无机材料的制备引起人们广泛的关注．然而对定向生长的聚合物纳米结构材料如聚合物的纳米管、线等的制备,却未见报道．最近,德国马普微结构研究所通过模板法制得了具有取向一致的聚合物纳米结构材料,该材料在化学传感器、药物输送以及微环境研究等方面具有广泛的应用前景．