Sulfide and sulfoxide based poly(ether-amide)s: Synthesis and characterization

Two new diacid monomers, 2,2′-sulfide bis(4-methyl phenoxy acetic acid) and 2,2′-sulfoxide bis(4-methyl phenoxy acetic acid) were successfully synthesized by refluxing the 2,2′-sulfide bis(4-methyl phenol) and 2,2′-sulfoxide bis(4-methyl phenol) with chloroacetonitrile in the presence of potassium carbonate, and subsequent basic reduction. Two novel series of poly(sulfide-ether-amide)s and poly(sulfoxide-ether-amide)s with aliphatic units in the main chain were prepared from diacids with various diamines.The polyamides were obtained in quantitative yields and their inherent viscosities were in the range of 0.43-0.89 dl g⁻¹ at a concentration of 0.5 g dl⁻¹ in N,N-dimethylacetamide (DMAc) solvent at 25 °C. They showed good thermal stability. The temperature for 10% weight loss in argon atmosphere was in the range of 350-415 °C. The polymers showed glass transition temperatures between 228 and 261 °C. Almost all of the polyamides were readily soluble in a variety of polar solvents such as N-methyl-2-pyrrolidone (NMP) and dimethyl sulfoxide (DMSO).     

Synthesis and characterization of some novel aromatic polyimides

Three new diamines 1,2-di(p-aminophenyloxy)ethylene, 2-(4-aminophenoxy)methyl-5-aminobenzimidazole and 4,4-(aminopheyloxy) phenyl-4-aminobenzamide were synthesized and polymerized with 3,3′,4,4′-benzophenone tetracarboxylic acid dianhydride (BP), 4,4′-(hexafluoroisopropyledene)diphthalic anhydride (HF) and 3,4,9,10-perylene tetracarboxylic acid dianhydride (PD) either by one step solution polymerization reaction or by two step procedure. The later includes ring opening poly-addition to give poly(amic acid), followed by cyclodehydration to polyimides with the inherent viscosities 0.62-0.97 dl/g. Majority of polymers are found to be soluble in most of the organic solvents such as DMSO, DMF, DMAc, m-cresol even at room temperature and few becomes soluble on heating. The degradation temperature of the resultant polymers falls in the ranges from 240 °C to 550 °C in nitrogen (with only 10% weight loss). Specific heat capacity at 300 °C ranges from 1.1899 to 5.2541 J g⁻¹ k⁻¹. The maximum degradation temperature ranges from 250 to 620 °C. T_g values of the polyimides ranged from 168 to 254 °C.     

Synthesis and characterization of poly(thioether ether sulfone imide)s derived from isomeric bis(chlorophthalimide)s and bis(4-mercaptophenyl) sulfone

A series of isomeric bis(chlorophthalimide)s (BCPIs) were conveniently prepared from 3-chlorophthalic anhydride, 4-chlorophthalic anhydride, and mixtures thereof. Polymerization of BCPIs with bis(4-mercaptophenyl) sulfone (BMPS) proceeded smoothly in the presence of tributylamine, from which a class of isomeric poly(thioether ether sulfone imide)s (PTESIs) with inherent viscosities of 0.45-0.82 dL/g were obtained. The solubility, thermal stability, and mechanical properties of these polymers were characterized. Compared to the PTESIs derived from single BCPIs, i.e., 3,3′-, 3,4′-, or 4,4′-BCPIs, the PTESIs derived from mixed BCPIs showed better solubility and higher storage modulus. These PTESIs also demonstrated good thermal stability, giving only 5% weight loss at temperature of 490 °C in nitrogen atmosphere. The glass transition temperatures (T_gs) of these isomeric PTESIs were between 242 and 265 °C, and were increased with increasing of the ratio of 3-chlorophthalimide unit in the polymer backbone.     

Some aromatic polyimides based on diamines containing hydrazo group and ether linkages

Three new hydrazo-bridged diamines, 4,4′-bis [4-(4-aminophenyloxy) phenylhydrazyl] biphenyl (BPD-2), 4,4′-bis [4-(4-aminophenyloxy) phenylhydrazyl] biphenyl ether (SPD-2) and 4,4-bis [4-(4-aminophenyloxy) phenyl] hydrazine (APD-2), were synthesized by the reduction of three azo-diols, 4,4′-bis (4-azo-1-hydroxyphenyl) biphenyl (BPD), 4,4′-bis (4-azo-1-hydroxyphenyl) biphenyl ether (SPD) and azo-4-hydroxybenzene (APD), and polymerized with pyromellitic dianhydride (PM), 3,3′,4,4′-benzophenone tetracarboxylic acid dianhydride (BP) and 3,4,9,10-perylenetetracarboxylic acid dianhydride (PR) either by one-step solution polymerization or by two-step procedure which includes ring-opening polyaddition to give poly(amic acid) followed by cyclic dehydration to polyimide. The monomers and polyimides were characterized by their elemental analyses, FTIR and ¹H NMR spectroscopy. Glass transition temperatures of the polymers are quite high (175-310 °C), characteristic of polyimides. The decomposition temperatures for 10% weight loss fall in the range of 280-575 °C in nitrogen. Activation energies of pyrolysis for each of the polymers calculated from Horowitz and Metzger's method are also high (52.54-95.28 kJ mol⁻¹). The inherent viscosities of the polyimides at a concentration of 0.5 g/dl in DMF range from 0.94 to 1.93 dl/g.     

New soluble, thermally stable poly(amide-imide)s containing cardo anthraquinone unit

Preparation of new types of polyimides with high thermal stability and improved solubility was considered. In this way, two new amide diamines containing bulky pendant units were prepared in two steps: nucleophilic substitution reactions of 1- and 2-aminoanthraquinone with 3,5-dinitrobenzoyl chloride to form amide containing dinitro compounds, and then reduction of resulted dinitro compounds with hydrazine monohydrate in the presence of palladium/activated carbon. Two series of new poly(amide-imide)s were prepared from the reactions of these two diamines with various dianhydrides by one step polyimidation process. All poly(amide-imide)s were characterized by FTIR and ¹H-NMR spectroscopies and elemental analysis. The polymers were obtained in high yields with inherent viscosities of 0.54-0.69 dl g⁻¹. X-ray diffraction patterns (XRD) showed that all the polymers were amorphous and therefore this factor in addition to the introduction of bulky anthraquinone group led to good solubility of the polymers in most common organic solvents especially in N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), and dimethylsulfoxide (DMSO). Thermal analysis showed glass transition temperature between 204 and 226 °C. Decomposition temperatures were more than 293 °C, also 10% weight loss were in the range of 387-419 °C in air.     

Synthesis and properties of novel organosoluble polyimides derived from bis[3-(4-amino-2-trifluoromethylphenoxy) phenyl] ether

A new aromatic ether diamine, bis[3-(4-amino-2-trifluoromethylphenoxy) phenyl] ether, was successfully synthesized via nucleophilic substitution reaction of 3,3′-oxydiphenol and 2-chloro-5-nitrotrifluoromethylbenzene, followed by a catalytic reduction. A series of new polyimides were synthesized from the diamine with various commercially available aromatic dianhydrides via a conventional two-stage process, i.e. ring-opening polyaddition forming the poly(amic acid)s and further thermal or chemical imidization forming polyimides. The resulting polyimides exhibited good solubility in polar solvents, such as N,N-dimethylacetamide, N,N-dimethylformamide, N-methyl-2-pyrrolidinone and common solvents such as chloroform, tetrahydrofuran upon heating and possessed the inherent viscosities of 0.51-0.68 dL/g. The resulting strong and flexible films exhibited excellent thermal stability with the temperature at 10% weight loss is above 502 °C and the glass transition temperature in the range of 191-232 °C. The polyimides also were found to possess high optical transparency.     

New ionic liquids with the bis[bis(pentafluoroethyl)phosphinyl]imide anion, [(C2F5)2P(O)]2N—Synthesis and characterization

A new series of low melting and hydrophobic ionic liquids (ILs) containing the bis[bis(pentafluoroethyl)phosphinyl]imide anion, [(C₂F₅)₂P(O)]₂N⁻ (FPI), and ammonium, phosphonium, imidazolium, pyridinium or pyrrolidinium cations were prepared and characterized. Their density, viscosity, melting point, glass transition temperature, decomposition temperature and conductivity are discussed. Many of these ionic liquids are liquids at room temperature with melting points below 15 °C, viscosities below 110 mm² s⁻¹ and thermal stabilities above 300 °C.     

Synthesis and properties of ortho‐linked aromatic polyimides based on 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene

A bis(ether amine) containing the ortho‐substituted phenylene unit and pendant tert‐butyl group, 1,2‐bis(4‐aminophenoxy)‐4‐tert‐butylbenzene, was synthesized and used as a monomer to prepare polyimides with six commercial dianhydrides via a conventional two‐stage procedure. The intermediate poly(amic acid)s had inherent viscosities of 0.78–1.44 dL/g, and most of them could be thermally converted into transparent, flexible, and tough polyimide films. The inherent viscosities of the resulting polyimides were in the range of 0.46–0.87 dL/g. All polyimides were noncrystalline, and most of them showed excellent solubility in polar organic solvents. The glass‐transition temperatures of these polyimides were in the range of 222–259 °C in differential scanning calorimetry and 212–282 °C in thermomechanicl analysis. These polyimides showed no appreciable decomposition up to 500 °C in thermogravimetric analysis in air or nitrogen. A comparative study of the properties with the corresponding polyimides without pendant tert‐butyl groups derived from 1,2‐bis(4‐aminophenoxy)benzene is also presented. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1551–1559, 2000     

Synthesis and characterization of soluble polyimides derived from a novel unsymmetrical diamine monomer: 1,4-(2′,4″-diaminodiphenoxy)benzene

A new aromatic unsymmetrical diamine monomer, 1,4-(2′,4″-diaminodiphenoxy)benzene (OAPB), was successfully synthesized in three steps using hydroquinone as starting material and polymerized with various aromatic tetracarboxylic acid dianhydrides, including 4,4′-oxydiphthalic anhydride (ODPA), 3,3′,4,4′-benzophenone tetracarboxylic dianhydride (BTDA), 2,2′-bis(3,4-dicarboxyphenyl)-hexafluoropropane dianhydride (6FDA) and pyromellitic dianhydride (PMDA) via the conventional two-step thermal or chemical imidization method to produce a series of the unsymmetrical aromatic polyimides. The polyimides were characterized by solubility tests, viscosity measurements, IR, ¹H NMR, and ¹³C NMR spectroscopy, X-ray diffraction studies, and thermogravimetric analysis. The polyimides obtained had inherent viscosities ranged of 0.38-0.58 dL/g, and were easily dissolved in common organic solvents. The resulting strong and flexible PI films exhibited excellent thermal stability with the decomposition temperature (at 5% weight loss) of above 505 °C and the glass transition temperature in the range of 230-299 °C. Moreover, the polymer films showed outstanding mechanical properties with the tensile strengths of 41.4-108.5 MPa, elongation at breaks of 5-9% and initial moduli of 1.15-1.68 GPa.     

A high-throughput method for determination of metabolites of organophosphate flame retardants in urine by ultra performance liquid chromatography–high resolution mass spectrometry

Organophosphate triesters are common flame retardants used in a wide variety of consumer products from which they can migrate and pollute the indoor environment. Humans may thus be continuously exposed to several organophosphate triesters which might be a risk for human health. An analytical method based on direct injection of 5 μL urine into an ultra performance liquid chromatography system coupled to a time-of-flight mass spectrometry has been developed and validated to monitor exposure to organophosphate triesters through their respective dialkyl and diaryl phosphate metabolites (DAPs). The targeted analytes were: di-n-butyl phosphate (DNBP), diphenyl phosphate (DPHP), bis(2-butoxyethyl) phosphate (BBOEP), bis(2-chloroethyl) phosphate (BCEP), bis(1-chloro-2-propyl) phosphate (BCPP) and bis(1,3-dichloro-2-propyl) phosphate (BDCIPP). Separation was achieved in less than 3 min on a short column with narrow diameter and small particle size (50 mm × 2.1 mm × 1.7 μm). Different mobile phases were explored to obtain optimal sensitivity. Acetonitrile/water buffered with 5 mM of ammonium hydroxide/ammonium formate (pH 9.2) was the preferred mobile phase. Quantification of DAPs was performed using deuterated analogues as internal standards in synthetic urine (averaged DAP accuracy was 101%; RSD 3%). Low method limits of quantification (MLQ) were obtained for DNBP (0.40 ng mL⁻¹), DPHP (0.10 ng mL⁻¹), BDCIPP (0.40 ng mL⁻¹) and BBOEP (0.60 ng mL⁻¹), but not for the most polar DAPs, BCEP (∼12 ng mL⁻¹) and BCPP (∼25 ng mL⁻¹). The feasibility of the method was tested on 84 morning urine samples from 42 mother and child pairs. Only DPHP was found above the MLQ in the urine samples with geometric mean (GM) concentrations of 1.1 ng mL⁻¹ and 0.57 ng mL⁻¹ for mothers and children respectively. BDCIPP was however, detected above the method limit of detection (MLD) with GM of 0.13 ng mL⁻¹ and 0.20 ng mL⁻¹. While occasionally detected, the GM of DNBP and BBOEP were below MLD in both groups.     

Synthesis and characterization of novel sulfonated naphthalenic polyimides as proton conductive membrane for DMFC applications

To prepare proton conductive membrane for direct methanol fuel cells (DMFC), a novel sulfonated aromatic diamine monomer, 1,4-bis(4-amino-2-sulfonic acid-phenoxy)-benzene (DSBAPB) was synthesized and characterized by ¹H NMR and FT-IR. Then a series of sulfonated polyimides (SPIs) were prepared from DSBAPB with 1,4,5,8-naphthalene tetracarboxylic dianhydride (NTDA) and a non-sulfonated diamine, 4,4′-oxydianiline (ODA) via one-step high-temperature polymerization method. The sulfonation degree of the SPIs can be controlled by changing the mole ratio of sulfonated monomer to non-sulfonated monomer. The obtained SPI membranes exhibit desirable proton conductivity ranged from 7.9 × 10⁻³ to 7.2 × 10⁻² S cm⁻¹ and low methanol permeability of less than 2.85 × 10⁻⁷ cm² s⁻¹. Furthermore, the hydrolysis stability of the obtained SPIs is better than the BDSA based SPIs caused by the flexible structure.     

Thermal degradation kinetics of polyimide containing 2,6-benzobisoxazole units

A novel polyimide (PI) based on 2,6-bis(p-aminophenyl)-benzo[1,2-d;5,4-d′]bisoxazole has been synthesized via a conventional two-stage procedure with bis(ether anhydrides) (HQDPA). The intermediate poly(amic acid) had inherent viscosities of 1.70 dl/g and could be thermally converted into light yellow polyimide film. The resulted polyimide showed excellent thermal stability, and the glass transition temperatures (T_g) were above 283 °C, the 5% weight loss temperature of the polymer was at 572 °C in N₂. The thermal degradation of the polyimide was studied by thermogravimetric analysis (TGA) in order to determine the actual reaction mechanisms of the decomposition process. The activation energy of the solid-state process was determined using Flynn-Wall-Ozawa method, which does not require knowledge of the reaction mechanism, which resulted to be 361.36 kJ/mol. The activation energy of different mechanism models and pre-exponential factor (A) were determined by Coats-Redfern method. Compared with the value obtained from the Ozawa method, the actual reaction mechanism obeyed nucleation and growth model, Avrami-Erofeev function (A₃) with integral form g(X) = [−ln(1−X)]³.     

Synthesis and characterization of soluble polyimides based on a new fluorinated diamine: 4-Phenyl-2,6-bis[3-(4′-amino-2′-trifluoromethyl-phenoxy) phenyl] pyridine

A new kind of pyridine-containing aromatic diamine monomer, 4-phenyl-2,6-bis[3-(4′-amino-2′-trifluoromethyl-phenoxy) phenyl] pyridine (m-PAFP), was successfully synthesized by a modified Chichibabin reaction of 3-(4′-nitro-2′-trifluoro-methyl-phenoxy)-acetophenone with benzaldehyde, followed by a catalytic reduction. A series of fluorinated pyridine-bridged aromatic poly(ether-imide)s were prepared from the resulting diamine monomer with various aromatic dianhydrides via a conventional two-step thermal or chemical imidization method. The inherent viscosities values of these polyimides were in the range of 0.56-1.02 dL/g, and they could be cast and thermally converted into transparent, flexible, and tough polyimide films. The polyimides displayed higher solubility in polar solvents such as NMP, DMSO and m-cresol. The polyimides had good thermal stability, with the glass transition temperatures (T_g) of 187-211 °C, the temperatures at 5% weight loss of 511-532 °C, and the residue at 800 °C in air was higher than 50%. These films also had dielectric constants of 2.64-2.74 at 10 MHz and low water uptake 0.53-0.66%. Wide-angle X-ray diffraction measurements revealed that these polyimides were predominantly amorphous. Moreover, the polymer films of these novel polyimides showed outstanding mechanical properties with the tensile strengths of 90.1-96.6 MPa, elongations at breakage of 8.9-10.7% and tensile modulus of 1.65-1.98 GPa.     

Synthesis of novel soluble poly(imide-siloxane)s via hydrosilylation: Characterization and structure property behaviour

A series of novel poly(imide-siloxane)s (PIS) were synthesized by the grafting of amine terminated soluble imides to the siloxane backbone. The amine terminated imides were synthesized by choosing suitable anhydrides and amines to get the imides that are soluble in polar and non-polar solvents. The imides were grafted to the siloxane backbone by the epoxy group cleavage. All the polymers were obtained in quantitative yields with the inherent viscosities ranging from 0.22 to 1.2 dL g⁻¹. The polymers were characterized by FT-IR, ¹H and ¹³C NMR, and were examined for their thermal properties. The polymers were found to be stable up to a temperature 350 °C. The DSC results showed a single glass transition in the negative temperature, whereas the DTA revealed another glass transition in the positive end for some of the polymers showing phase separation. Polymer films were prepared employing the coupling reaction between PIS and the polydimethylsiloxane matrix by varying the amount of incorporation of PIS in the films. The polymer films had a tensile strength of 35-82 MPa with a percentage elongation of 86-271%. The contribution of polar and dispersion component towards the total surface energy was studied by the contact angle measurement and a reduction in surface tension of 14 mN m⁻¹ was achieved with the fluorine containing PIS membrane.     

Novel thermally stable and chiral poly(amide-imide)s bearing from N,N′-(4,4′-diphthaloyl)-bis-l-isoleucine diacid: Synthesis and characterization

Novel optically active aromatic poly(amide-imide)s (PAIs) were prepared from newly synthesized N,N′-(4,4′-diphthaloyl)-bis-l-isoleucine diacid (3) via polycondensation with various diamines. The diacid was synthesized by the condensation reaction of 3,3′,4,4′-biphenyltetracarboxylic dianhydride (1) with l-isoleucine (2) in a mixture of acetic acid and pyridine (3:2 v/v). All the polymers were obtained in quantitative yields with inherent viscosities of 0.20-0.43 dL g⁻¹. All the polymers were highly organosoluble in solvents like N-methyl-2-pyrrolidinone (NMP), N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), tetrahydrofuran, γ-butyrolactone, cyclohexanone and chloroform at room temperature or upon heating. These poly(amide-imide)s had glass transition temperatures between 198 and 231 °C, and their 10% weight-loss temperatures were ranging from 368 to 398 °C and 353 to 375 °C under nitrogen and air, respectively. The polyimide films had tensile strengths in the range of 63-88 MPa and tensile moduli in the range of 0.8-1.4 GPa. These poly(amide-imide)s possessed chiral properties and the specific rotations were in the range of −3.10° to −72.92°.     

Synthesis and properties of new pyridine-bridged poly(ether-imide)s based on 4-(4-trifluoromethylphenyl)-2,6-bis[4-(4-aminophenoxy)phenyl]pyridine

A novel pyridine-containing aromatic diamine monomer, 4-(4-trifluoromethylphenyl)-2,6-bis[4-(4-aminophenoxy)phenyl]pyridine (FAPP), was synthesized via the modified Chichibabin pyridine synthesis of 4-(4-nitrophenoxy)-acetophenone with 4-trifluoromethyl-benzaldehyde, followed by a catalytic reduction. A series of fluorinated pyridine-bridged aromatic poly(ether-imide)s were prepared from the resulting diamine monomer with various aromatic dianhydrides via a conventional two-step process. The resulting polyimides exhibited good solubility in aprotic amide solvents and m-cresol, such as N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and m-cresol, etc., which possessed the inherent viscosities of 0.76-0.91 dL/g. Strong and flexible poly(ether-imide) films were obtained, which showed excellent thermal properties with the glass transition temperatures of 268-353 °C, the temperature at 5% weight loss of 547-595 °C, and the residue at 700 °C of 65-74% in nitrogen, good mechanical properties with the tensile strengths of 87.6-104.2 MPa and elongations at breakage of 8.9-12.6%, and good optical transparency with the cut-off wavelengths of 357-380 nm, as well as low dielectric constants in the range of 2.49-3.04 at 1 MHz and low water uptake 0.43-0.69%. Furthermore, the resulted polyimides derived from FAPP were compared with non-fluorinated analogous polyimides and fluorinated analogous polyimides with trifluoromethyl groups in different positions, and the effects of substituents were also investigated and discussed.     

Batch and hydrodynamic monitoring of vitamin C using novel periodate selective sensors based on a newly synthesized Ni(II)-Schiff bases complexes as a neutral receptors

A highly selective membrane electrodes based on a two newly synthesized nickel (II) Schiff bases, [NiL¹] and [NiL²] where L¹ and L² are N,N/bis(salicylaldehyde)4,5-dimethyl-1,2-phenylenediamine (H₂L¹) and N,N/bis(salicylaldehyde)4,5-dichloro-1,2-phenylenediamine (H₂L²) were used as a neutral carrier ionophores for static and hydrodynamic potentiometric mode of operations for the determination of periodate. Under static mode of operation, the sensors displayed a near-Nernstian slope of −66.1 ± 0.8 and −59.9 ± 1.1 mV decade⁻¹ of activity and detection limits to 5.2 × 10⁻⁶ and 7.3 × 10⁻⁶ mol L⁻¹ for the sensors based on [NiL¹] and [NiL²], respectively. Under hydrodynamic mode of operation (FIA), the slope of the calibration plot, limit of detection, and working linear range were −71.1 mVdecade⁻¹ of activity, 7.3 × 10⁻⁶ and 1.0 × 10⁻⁵ to 1.0 × 10⁻³ mol L⁻¹, respectively. The response time of the sensors in whole concentration ranges was very short (<10 s). The response of the sensors was independent on the pH range of 3-8. A tubular version was further developed and coupled to a flow injection system for ascorbic acid (AA) determination in beverages and pharmaceutical preparations. This approach was achieved by selecting a 50-cm reactor and an overall flow of 3 mL min⁻¹, and injecting volume 100 μL of AA standards in a 1.0 × 10⁻⁴ mol L⁻¹ IO₄⁻ solution. Under these conditions, a linearity range of 2-13 μg mL⁻¹, with a slope of 4.97 mV (mg/L)⁻¹ (r² = 0.9995), detection limit 0.9 mg L⁻¹ and a reproducibility of ±1.1 mV (n = 5) was recorded. This simple and inexpensive flow injection analysis manifold, with a good potentiometric detector, enabled the analysis of ∼50 samples h⁻¹ without requiring pretreatment procedures. An average recovery of 98.8% and a mean standard deviation of 1.3% were obtained.     

[2]Pseudorotaxanes based on the cryptand/monopyridinium recognition motif

The first cryptand/monopyridinium [2]pseudorotaxanes were prepared from five bis(m-phenylene)-32-crown-10- and one bis(m-phenylene)-26-crown-8-based cryptand hosts and three monopyridinium guests. These pseudorotaxanes were studied by proton NMR spectroscopy, mass spectrometry, and X-ray crystallography. Association constants ranged from 141 M⁻¹ to 1.86×10⁴ M⁻¹ in 1:1 acetone: chloroform at 22 °C.     

Electrochemical behavior of hexafluoroniobate, heptafluorotungstate, and oxotetrafluorovanadate anions in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide room temperature ionic liquid

Electrochemical behavior of hexafluoroniobate (Nb(V)F₆⁻), heptafluorotungstate (W(VI)F₇⁻), and oxotetrafluorovanadate (V(V)OF₄⁻) anions has been investigated in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide (BMPyrTFSA) ionic liquid at 298 K by means of cyclic voltammetry and chronoamperometry. Cyclic voltammograms at a Pt electrode showed that Nb(V)F₆⁻ anion is reduced to Nb(IV)F₆²⁻ by a one-electron reversible reaction. Electrochemical reductions of W(VI)F₇⁻ and V(V)OF₄⁻ anions at a Pt electrode are quasi-reversible and irreversible reactions, respectively, according to cyclic voltammetry. The diffusion coefficients of Nb(V)F₆⁻, W(VI)F₇⁻ and V(V)OF₄⁻ determined by chronoamperometry are 1.34 × 10⁻⁷, 7.45 × 10⁻⁸ and 2.49 × 10⁻⁷ cm² s⁻¹, respectively. The Stokes radii of Nb(V)F₆⁻, W(VI)F₇⁻, and V(V)OF₄⁻ in BMPyrTFSA have been calculated to be 0.23, 0.38, and 0.12 nm, from the diffusion coefficients and viscosities obtained.     

Highly selective thiocyanate membrane electrode based on butane-2,3-dione bis(salicylhydrazonato)zinc(II) complex

A highly selective poly(vinyl chloride) (PVC) membrane electrode based on butane -2,3-dione bis(salicylhydrazonato) zinc(II) [Zn (BDSH)] complex as carrier for thiocyanate-selective electrode is reported. The influence of membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. The sensor responds to thiocyanate in linear range from 1.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a slope −56.5 ± 1.1 mV decade⁻¹, over a wide pH range of 3.5-8.5. The limit of detection of the electrode was 7.0 × 10⁻⁷ M SCN⁻. Selectivity coefficients determined with fixed interference method (FIM) indicate a good discriminating ability towards SCN⁻ ion in comparison to other anions. The proposed sensor has a fast response time of about 5-15 s and can be used for at least 3 months without any considerable divergence in potential. It was applied as indicator electrode in titration of thiocyanate with Ag⁺ and in potentiometric determination of thiocyanate in saliva and urine samples.