Synthesis and characterization of new telechelic poly(phenyleneoxide)s

New well-defined telechelic poly(phenyleneoxide)s (PPO's) were synthesized from 4-bromo-2,6-dimethylphenol and bi-phenolic compounds through phase transfer catalyzed aromatic nucleophilic substitution polymerization. Bisphenol-A (BPA), 4,4^′-biphenol (BP), hydroquinone (HQ) and 2,6-dihydroxynaphthalene (DHN) were employed as telechelic units. The composition analysis by proton-nuclear magnetic resonance (¹H-NMR) spectroscopy revealed that DHN was highly reactive compared to BPA and HQ, whereas BP was un-reactive in the polymerization process. The number average repeating unit (n) in telechelic PPO was estimated as n=17-19 and n=17-20 for DHN and BPA (or HQ), respectively. The reactivity of the bi-phenolic in PPO synthesis are confirmed as DHN > HQ ∼ BPA ? BP. The molecular weight determination by gel permeation chromatography (GPC) and viscosity method suggest that the molecular weight of PPO decreased drastically with increasing amount of bi-phenolic units in the feed. The GPC chromatogram of PPO showed a bi-modal distribution, clearly indicative of formation of two different types of molecular weight chains, whereas the telechelic polymers have a mono-modal distribution with a narrow polydispersity. Thermal analysis by differential scanning calorimetry revealed that telechelic polymers are highly amorphous, like PPO, and no crystallization or melting peaks were observed in the heating/cooling cycles.     

OXIDATIVE POLYMERIZATION BEHAVIOR OF 2,6-DIMETHYLPHENOL IN AQUEOUS MEDIA WITH POTASSIUM FERRICYANIDE

The effects of potassium ferricyanide,sodium n-dodecyl sulfate,sodium hydroxide and temperature on the molecular weight and the yield of poly(2,6-dimethyl-1,4-phenylene oxide)(PPO) synthesized in an aqueous medium were studied.It was found that oxygen in air had little influence on the oxidative polymerization of 2,6-dimethylphenol(DMP) in the aqueous medium,and potassium ferricyanide was only an oxidant during the oxidative polymerization of DMP.Sodium n-dodecyl sulfate could stabilize polymer particles...     

水介质中2,6-二甲基苯酚的氧化偶合聚合

聚2,6-二甲基苯醚(PPO)是重要的工程塑料,一般采用在有机溶剂中使2,6-二甲基苯酚(DMP)氧化聚合的方法合成,这就需要溶剂回收装置和防爆反应器,且污染环境.从绿色化学观点出发,以水作为反应介质,不仅对环境友好,而且PPO不溶于水,容易分离.近年来,一些学者研究了在油/水两相或全水介质中使DMP氧化聚合合成PPO的新方法.本文主要综述了该方法的研究进展,包括DMP氧化聚合的机理,油/水两相或水介质中对聚合速率、氧化偶合选择性及PPO分子量等的影响因素.     

Styrene polymerization with novel anilido-imino nickel complexes/MAO catalytic system: Catalytic behavior, microstructure of polystyrene and polymerization mechanism

The polymerization of styrene with novel catalytic systems of anilido-imino nickel complexes (Ar¹N = CHC₆H₄NAr²) NiBr (Ar¹ = Ar² = 2,6-dimethylphenyl, 1; Ar¹ = 2,6-dimethylphenyl, Ar² = 2,6-diisopropylphenyl, 2; Ar¹ = Ar² = 2,6-diisopropylphenyl, 3; Ar¹ = 2,6-diisopropylphenyl, Ar² = 2,6-dimethylphenyl, 4) activated by methylaluminoxane was investigated. The influence of reaction parameters (temperature, Al/Ni mole ratio, and polymerization time) on styrene polymerization was evaluated. The influence of the bulkiness of the substituents on polymerization activity and polymer characteristics was also ascertained. The obtained polystyrene was an iso-rich atactic polymer and its weight-average molecular weight reached 70 500. NMR analysis of the end groups further confirmed that styrene polymerization catalyzed by anilido-imino nickel complexes/MAO systems proceeded through a coordination mechanism, and the chain was initiated through styrene secondary insertion into the NiH and terminated mainly through β-H elimination of styrene producing the chain-end group (CHCHPh).     

Study on the polymerizations of methyl methacrylate and styrene initiated with chlorotrimethylsilane and CuCl/N,N,N′,N″,N″-pentamethyldiethyltriamine

Methyl methacrylate (MMA) and styrene (St) have been radically polymerized in the presence of chlorotrimethylsilane and CuCl/N,N,N′,N″,N″-pentamethyldiethyltriamine (Me₃SiCl/CuCl/PMDETA). An analysis of the resultant polymers by ¹H NMR discloses terminal silyl group and chlorine atom in all the obtained polymers. Kinetics studies have been carried out by measuring monomer conversions and polymer molecular weights against polymerization time. The results indicate that, for both MMA and St polymerizations, the monomer conversions exhibit a quasi-linear relationship with polymerization time, and the polymer number-average molecular weight (M_n) also increases with monomer conversion. The molecular weights of both PS and PMMA exceed one hundred thousand. Regardless of molecular weight, all the polymers show narrow molecular distributions (M_w/M_n = 1.2-1.5). These polymerization reactions are speculated to follow a mechanism similar to that of atom transfer radical polymerization (ATRP).     

Synthesis of well-defined ABC triblock copolymers with polypeptide segments by ATRP and click reactions

Well-defined ABC block copolymers consisting of poly(ethylene oxide) monomethylene ether (MPEO) as A block, poly(styrene) (PS) as B block and poly(γ-benzyl-l-glutamate) (PBLG) as C block were synthesized by the combination of atom transfer radical polymerization (ATRP) and click reactions. The bromine-terminated diblock copolymer poly(ethylene oxide) monomethylene ether-block-poly(styrene) (MPEO-PS-Br) was prepared by ATRP of styrene initiated with macro-initiator MPEO-Br, which was prepared from the esterification of MPEO and 2-bromoisobutyryl bromide, and converted into the azido-terminated diblock copolymer MPEO-PS-N₃ by simple nucleophilic substitutions in DMF in the presence of sodium azide. Propargyl-terminated PBLGs were synthesized by ring-opening polymerization of γ-benzyl-l-glutamate-N-carboxyanhydride in DMF at room temperature using propargyl amine as an initiator. ABC triblock copolymers MPEO-PS-PBLG with a wide range of number-average molecular weights from 1.55 to 3.75 × 10⁴ and a narrow polydispersity from 1.07 to 1.10 were synthesized via the click reaction of MPEO-PS-N₃ and the propargyl-terminated PBLG in the presence of CuBr and 1,1,4,7,7-pentamethyldiethylenetriamine (PMDETA) catalyst system. The structures of these ABC block copolymers and corresponding precursors were characterized by NMR, IR and GPC. The results showed that click reaction was efficient. Therefore, a facile approach was offered to synthesize ABC triblock copolymers composed of crystallizable polymer MPEO, conventional vinylic polymer PS and rod-like α-helix polypeptide PBLG.     

Thermal and mechanical properties of in situ polymerized PS/EPDM blends

In situ polymerized PS/EPDM blends were prepared by dissolving poly(ethylene-co-propylene-co-2-ethylidene-5-norbornene) (EPDM) in styrene monomer, followed by bulk polymerization at 60 °C and 80 °C . EPDM has excellent resistance to such factors as weather, ozone and oxidation, attributed to its non-conjugated diene component, and it could be a good alternative for substituting polybutadiene-based rubbers in PS toughening. The in situ polymerized blends were characterized by dynamic mechanical analysis, thermogravimetric analysis, gel permeation chromatography, and tensile and Izod impact resistance tests. The PS/EPDM blends are immiscible and present two phases, a dispersed elastomeric phase (EPDM) in a rigid PS matrix whose phase behavior is strongly affected by the polymerization temperature. Mechanical properties of the blends are influenced by the increase in the average size of EPDM domains with the increase in the polymerization temperature and EPDM content. The blends polymerized at 60 °C containing 5 wt% of EPDM presents an increase in the impact resistance of 80% and containing 17 wt% of EPDM presents an increase in the strain at break of 170% in comparison with the value of PS. The blend polymerized at 80 °C containing 17 wt% of EPDM presents an increase in the strain at break of 480% and in impact resistance of 140% in comparison with the value of PS.     

Synthesis and characterization of novel poly(cycloalkyl methacrylate) bearing fused‐ring structure and its copolymers

A new family of cycloaliphatic fused‐ring acrylic polymers based on 8‐hydroxymethyltricyclo[5.2.1.0^2,6]decane (TCD) has been synthesized by free‐radical polymerization. TCD‐methacrylate (TCD‐MA) was synthesized by reacting TCD with methacrylic acid in toluene via transesterification with p‐toluenesulfonic acid as a catalyst. TCDMA was polymerized in toluene with benzoyl peroxide as a free‐radical initiator at 80 °C. Copolymers were synthesized by polymerizing TCDMA with styrene and methyl methacrylate. The composition of the comonomers was varied from 0 to 100%. Homo‐ and copolymers were characterized by Fourier transform infrared (FTIR) and ¹³C NMR spectroscopy. Molecular weight determination by gel permeation chromatography showed that the polymers were obtained in very high molecular weights in the range of M_n > 50,000 and M_w > 80,000 with relatively low polydispersity. The composition analysis of both the copolymer series were determined by ¹H NMR. The thermal properties of the homo‐ and copolymers were studied with differential scanning calorimetry and all the polymers were found to be amorphous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5617–5626, 2004     

Synthesis and characterization of poly(phenylene oxide) graft copolymers by atom transfer radical polymerizations

A series of comb-like poly(phenylene oxide)s (PPO) graft copolymers with controlled grafting density and length of grafts were synthesized by atom transfer radical polymerization (ATRP). The α-bromo-poly(2,6-dimethyl-1,4-phenylene oxide)s (BPPO) were used as macroinitiators to polymerize vinyl monomers and the graft copolymers carrying polystyrene (PS), poly(p-acetoxystyrene) (PAS), and poly(methyl methacrylate) (PMMA) as side chains were synthesized and characterized by NMR, FTIR, GPC, DSC and TGA. The composition-dependent glass-transition temperatures (T_g) of PPO-g-PS exhibited good correlation with theoretical curve in Couchman equations except for the cases of low PS content (<40 mol%) copolymers in which a positive deviation was observed due to enhanced molecular interactions. The increase in monomer/initiator ratio led to the increase of degree of polymerization and the decrease of polydispersity. Despite the immiscibility nature between PPO and PMMA, the PPO-g-PMMA exhibited enhanced compatibilization as apparent single T_g in a wide temperature window throughout various compositions revealing an efficient segmental mixing on a molecular scale due to grafting structure.     

Phase transfer catalyzed polymerization of 4-bromo-2,6-dimethylphenol in the presence of either 2,4,6-trimethylphenol or 4-tert-butyl-2,6-dimethylphenol

The synthesis of poly(2,6-dimethyl-1,4-phenylene oxide) with one 2,6-dimethylphenol chain end (PPO–OH) and with well-defined molecular weight by phase transfer catalyzed polymerization of 4-bromo-2,6-dimethylphenol ( 20 ) in the presence of either 2,4,6-trimethylphenol ( 1 ) or 4-t-butyl-2,6-dimethylphenol ( 1 ′) as chain initiators is described. The range of controllable molecular weights and the mechanism of molecular weight control are discussed based on the differences between the reactivities of 20 , 1 , and 1 ′ and of the corresponding reactive species. The PPO–OH synthesized from 20 / 1 ′ has structural units derived from 1 ′ attached only at the chain end. PPO–OH synthesized from 20 / 1 contains structural units derived from 1 both internally and at the chain ends. Structural units derived from side reactions were identified by ¹H-NMR spectroscopy. A reaction mechanism is proposed to account for their formation.     

Synthesis and characterization of para-nitro substituted 2,6-bis(phenylimino)pyridyl Fe(II) and Co(II) complexes and their ethylene polymerization properties

Four iron(II) and cobalt(II) complexes ligated by 2,6-bis(4-nitro-2,6-R₂-phenylimino)pyridines, LMCl₂ (1: R = Me, M = Fe; 2: R = iPr, M = Fe; 3: R = Me, M = Co; 4: R = iPr, M = Co) have been synthesized and fully characterized, and their catalytic ethylene polymerization properties have been investigated. Among these complexes, the iron(II) pre-catalyst bearing the ortho-isopropyl groups (complex 2) exhibited higher activities and produced higher molecular weight polymers than the other complexes in the presence of methylaluminoxane (MAO). A comparison of 2 with the reference non-nitro-substituted catalyst (2,6-bis(2,6-diisopropylphenylimino)pyridyl)FeCl₂ (FeCat 5) revealed a modest increase of the catalytic activity and longer lifetime upon substitution of the para-positions with nitro groups (activity up to 6.0 × 10³ kg mol⁻¹ h⁻¹ bar⁻¹ for 2 and 4.8 × 10³ kg mol⁻¹ h⁻¹ bar⁻¹ for 5), converting ethylene to highly linear polyethylenes with a unimodal molecular weight distribution around 456.4 kg mol⁻¹. However, the iron(II) pre-catalyst 1 on changing from ortho-isopropyl to methyl groups displayed much lower activities (over an order of magnitude) than 2 under mild conditions. As expected, the cobalt analogues showed relatively low polymerization activities.     

Depolymerization of poly(2,6-dimethyl-1,4-phenylene oxide) under oxidative conditions

Depolymerization of an engineering plastic, poly(2,6-dimethyl-1,4-phenylene oxide) (PPO), was accomplished by using 2,6-dimethylphenol (DMP) under oxidative conditions. The addition of an excess amount of DMP to a solution of PPO in the presence of a CuCl/pyridine catalyst yielded oligomeric products. When PPO (M(n)=1.0x10(4), M(w)/M(n)=1.2) was allowed to react with a sufficient amount of DMP, the molecular weight of the product decreased to M(n)=4.9x10(2) (M(w)/M(n)=1.5). By a prolonged reaction with the oxidant, the oligomeric product was repolymerized to produce PPO essentially identical to the starting material, making the oligomer useful as a reusable resource. During the depolymerization reaction, an intermediate phenoxyl radical was observed by ESR spectroscopy. Kinetic analysis showed that the rate of the oxidation of PPO was about 10 times higher than that of DMP. These results show that a monomeric phenoxyl radical attacks the polymeric phenoxyl to induce the redistribution via a quinone ketal intermediate, leading to the substantial decrease in the molecular weight of PPO, which is much faster than the chain growth.     

Vinyl polymerization of norbornene catalyzed by a series of bis(β-ketoiminato)nickel (II) complexes in the presence of methylaluminoxane

A series of nickel complexes with β-ketoiminato ligands based on pyrazolone derivative were synthesized and characterized, which are highly active catalyst precursors for norbornene polymerization under mild reaction conditions through a vinyl-type polymerization mechanism. The catalytic activity could be up to 3.38 × 10⁷ g polymer/mol Ni h. The molecular weight distributions of the polynorbornenes (M_w/M_n = 2.05-2.56) indicate the presence of a single active species in the polymerization process.     

Synthesis of silica-polystyrene core-shell nanoparticles via surface thiol-lactam initiated radical polymerization

This paper reports the synthesis of structurally well-defined silica-polystyrene (SiO₂@PS) hybrid nanoparticles using a thiol-lactam-initiated, radical-polymerization technique. The surface of silica particles, 80 nm in size, were functionalized with (3-mercaptopropyl) trimethoxysilane and used as seeds in the polymerization of styrene in the presence of butyrolactam. ¹H nuclear magnetic resonance and X-ray photoelectron spectroscopy showed that the thiol groups on the SiO₂ surface could initiate polymerization with the aid of butyrolactam. Transmission electron microscopy showed that the hybrid particles had uniform core-shell morphologies. The molecular weight of grafted PS increased with increasing polymerization time.     

Kinetic and mechanistic study of the quasiliving cationic polymerization of styrene with the 2-phenyl-2-propanol/AlCl3 · OBu2 initiating system

The cationic polymerization of styrene with the 2-phenyl-2-propanol (CumOH)/AlCl₃ · OBu₂ initiating system at various dibutyl ether concentrations in a mixture of 1,2-dichloroethane and n-hexane (55:45 v/v) at −15 °C was investigated. The experimental results showed that an increase in dibutyl ether concentration leads to a noticeable decrease in the polymerization rate as well as to the more controlled polymerization in terms of molecular weight (M_n) and molecular weight distribution (MWD) evolutions. The kinetic investigation revealed that the polymerization proceeds in two stages. The first stage is characterized by high polymerization rate and slow initiation relative to propagation. During this stage molecular weight decreases or does not change and MWD increases with conversion. In the second stage considerably slower quasiliving polymerization of styrene occurs. The quasiliving nature of the styrene polymerization by the CumOH/AlCl₃ · OBu₂ system is proved and mechanistic scheme of the polymerization is proposed.     

Controlled radical polymerization of cholesteryl acrylate and its block copolymer with styrene via the RAFT process

Reversible addition fragmentation chain transfer (RAFT) polymerization of cholesteryl acrylate (ChA) was conducted using S-1-dodecyl-S′-(α,α′-dimethyl-α′′-acetic acid)trithiocarbonate as CTA and AIBN as initiator in toluene at 80 °C. The polymerization was investigated at two different CTA concentrations (0.025 and 0.040 M). Polymerization of ChA with CTA concentration of 0.040 M proceeds in a controlled/living manner as evidenced by linear increase of the molecular weight with conversion and narrow polymer polydispersity (PDI < 1.2). With lower initial CTA concentration, namely 0.025 M, although poly(cholesteryl acrylate) (PChA) exhibiting narrow molecular weight distributions could be synthesized, the polymerization showed relatively low control with many termination products. Chain extension polymerizations were performed starting from either the PChA or the polystyrene (PS) block, and well-defined copolymers based on ChA and styrene were prepared. Thermal properties of PChA and PS-b-PChA copolymer were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), and the results showed that both PChA and PS-b-PChA are amorphous polymers. PChA begins to decompose at ca. 218 °C with maximum weight loss rate at 351 °C, while PS-b-PChA shows double weight loss rate peaks located at 345 and 415 °C, respectively.     

Photoinitiating capabilities of vinyl polyperoxides and metamorphosis of block-into-block copolymer

This article describes the first comprehensive study on the use of a vinyl polyperoxide, namely poly(styrene peroxide) (PSP), an equimolar alternating copolymer of oxygen and styrene, as a photoinitiator for free radical polymerization of vinyl monomers like styrene. The molecular weight, yield, structure and thermal stability of polystyrene (PS) thus obtained are compared with PS made using a simple peroxide like di-t-butyl peroxide. Interestingly, the PS prepared using PSP contained PSP segments attached to its backbone preferably at the chain ends. This PSP–PS–PSP was further used as a thermal macroinitiator for the preparation of another block copolymer PS-b-PMMA by reacting PSP–PS–PSP with methyl methacrylate (MMA). The mechanism of block copolymerization has been discussed. © 1996 John Wiley & Sons, Inc.     

Synthesis of high molecular weight polystyrene using AGET ATRP under high pressure

High molecular weight polystyrene (PS) was synthesized by ATRP. Under atmospheric pressure (1 bar), PS with M_n up to 200,000 was prepared using either ARGET or ICAR ATRP. Under high pressure (6 kbar), higher molecular weight PS could be obtained due to accelerated radical propagation and diminished radical termination in polymerization of styrene. Therefore, it was possible to synthesize PS with M_n > 1,000,000 and M_w/M_n < 1.25 using AGET ATRP under a pressure of 6 kbar at room temperature. This is the highest molecular weight linear PS prepared by a controlled radical polymerization.     

Controlled synthesis and fluorescent properties of poly(9-(4-vinylbenzyl)-9H-carbazole) via nitroxide-mediated living free-radical polymerization

The functional polymer containing carbazole unit, [(poly(9-(4-vinylbenzyl)-9H-carbazole) (PVBK)], was successfully prepared via nitroxide-mediated living free-radical polymerization of 9-(4-vinylbenzyl)-9H-carbazole (VBK). The controlled features of the polymerization were confirmed by the linear increase in the molecular weight with the monomer conversion while keeping the relative narrow molecular weight distribution (M_w/M_n ? 1.51), and successful chain extension with styrene. The resulting polymer absorbed light in the 305-355 nm range and exhibited fluorescent emission at 350 nm. The fluorescent intensity of the polymer was lower than that of monomer and was affected by the properties of the different solvents, which decreased in the following order: DMF > THF > CHCl₃ at the same concentration of carbazole units. The fluorescence intensity of the polymer was apparently influenced by chromophore concentration, and the maximum value was obtained when the carbazole unit concentration was around 8 × 10⁻⁵ mol/L. Moreover, it was shown that the strong fluorescence of PVBK can be quenched by methyl acrylate (MA).     

Heteroarm H‐shaped terpolymers through the combination of the Diels–Alder reaction and controlled/living radical polymerization techniques

Heteroarm H‐shaped terpolymers (PS)(PtBA)–PEO–(PtBA)(PS) and (PS)(PtBA)–PPO–(PtBA)(PS) [where PS is polystyrene, PtBA is poly(tert‐butyl acrylate), PEO is poly(ethylene oxide), and PPO is poly(propylene oxide)], containing PEO or PPO as a backbone and PS and PtBA as side arms, were prepared via the combination of the Diels–Alder reaction and atom transfer radical and nitroxide‐mediated radical polymerization routes. Commercially available PEO or PPO containing bismaleimide end groups was reacted with a compound having an anthracene functionality, succinic acid anthracen‐9‐yl methyl ester 3‐(2‐bromo‐2‐methylpropionyloxy)‐2‐methyl‐2‐[2‐phenyl‐2‐(2,2,6,6‐tetramethylpiperidin‐1‐yloxy)ethoxycarbonyl]propyl ester, with a Diels–Alder reaction strategy. The obtained macroinitiator with tertiary bromide and 2,2,6,6‐tetramethylpiperidin‐1‐oxy functional end groups was used subsequently in the atom transfer radical polymerization of tert‐butyl acrylate and in the nitroxide‐mediated free‐radical polymerization of styrene to produce heteroarm H‐shaped terpolymers with moderately low molecular weight distributions (<1.31). The polymers were characterized with ¹H NMR, ultraviolet, gel permeation chromatography, and differential scanning calorimetry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3947–3957, 2006