Observations on the swelling characteristics of the zwitterionic hydrogel of poly(1-3-sulfopropyl)-2-vinyl-pyridinium-betaine hydrogel

Samples of poly[1-(3-sulfopropyl)-2-vinyl-pyridinium-betaine] (PSPV) have been synthesized to high conversion by free radical polymerization in aqueous solution of the zwitterionic monomer SPV with several concentrations of the crosslinker N,N′-methylene-bis-acrylamide (MBA). The densities of the resultant xerogels increased regularly with the content of MBA. Hydrogels obtained by swelling them in water and aqueous KSCN solution were examined by gravimetric and dimensional analysis. The water contents increased with decreasing content of MBA, the value of 92.7 wt% at the lowest MBA content being higher than that for other zwitterionic hydrogels. Enhanced swelling occurred in 1 M aq. KSCN at each MBA content, the total swelling being 98.1 wt% at the lowest crosslinker content. Swelling increased with increasing temperature. An approximate procedure to formulating swelling equilibrium in term of the volume fraction of water in hydrogel, in conjunction with the van’t Hoff equation, yields a small positive value for the enthalpy of swelling. This is compared with values derived similarly for other hydrogels.     

Network and thermodynamic properties of hydrogels of poly[1-(3-sulfopropyl)-2-vinyl-pyridinium-betaine]

Samples of poly[1-(3-sulfopropyl)-2-vinyl-pyridinium-betaine] (PSPV) have been synthesized to high conversion by free radical polymerization in aqueous solution of the zwitterionic monomer SPV with several concentrations of the crosslinker N,N′-methylene-bis-acrylamide (MBA). Hydrogels obtained by swelling them in water and aqueous KSCN solution were examined by gravimetric and dimensional analysis, and by compression-strain measurements. The derived effective crosslinking density ν_e was only ca. 11% of the theoretical value, indicating low efficiency of chemical crosslinking by MBA. At 298 K increasing content of MBA produces increases in the values of ν_e, elastic moduli and polymer-water interaction parameter χ. At a fixed MBA content, increasing temperature led to decreases in the values of ν_e, elastic moduli and χ, but an increase in water content of hydrogel. For swelling in aq. KSCN solution the mechanical properties are insensitive to content of salt. Experimental and theoretical analysis afforded values of the water/polymer, salt/water and salt/polymer interaction parameters. Where appropriate the findings are compared with those reported for a different zwitterionic hydrogel and a neutral non-zwitterionic hydrogel.     

Preparation of composites and nanocomposites based on bentonite and poly(sodium acrylate). Effect of amount of bentonite on the swelling behaviour

A series of composite and nanocomposite hydrogels were synthesized by copolymerization reaction of partially neutralized acrylic acid (SA) on bentonite micropowder (BT) using N,N′-methylenebisacrylamide (MBA) as a crosslinker and potassium persulfate (I) as an initiator in aqueous solution. The influences of Na⁺-BT, organoBT (O-BT), and the content of the BT in the copolymeric gels on the swelling behaviour in deionized water and saline solution (0.2 wt.% NaCl_(aq)) were investigated. Results showed that the equilibrium swelling (W_∞) was decreased by adding a small amount of the BT, however, at higher BT contents, the W_∞ increased with the increase of the amount of clay. It was found that a concentration of 14 wt.% Na⁺-BT gave the best results absorption (955 g/g). Moreover, the amount of swelling for these absorbents in saline solution was smaller than that in deionized water. These hydrogels were characterized by X-ray diffraction and scanning electron microscopy. Finally, the thermogravimetric analysis indicated that introduction of clay to the polymer network resulted in an increase in thermal stability.     

The effect of solvent composition on swelling and shrinking properties of poly(acrylamide-co-itaconic acid) hydrogels

The peculiarities of the equilibrium swelling ratio and swelling-shrinking kinetics of polyelectrolyte copolymeric hydrogels consisting of acrylamide and itaconic acid (AAm/IA) have been studied in water/nonsolvent (acetone, methanol, ethanol and 1-butanol) mixtures as a function of solvent composition and IA content in the hydrogel. The phase transition of these hydrogels was generated by changing the solvent composition by progressive substitution of water by the nonsolvent. For all P(AAm/IA) hydrogels, the form of the shrinking curves was determined to be strongly dependent on the type of the nonsolvent used. The rate of shrinking of these hydrogels increased in the order 1-butanol < ethanol < methanol < acetone.     

Swelling behaviour of thermo-sensitive hydrogels based on oligo(ethylene glycol) methacrylates

The thermo-sensitive swelling behaviour of hydrogels based on 2-(2-methoxyethoxy)ethyl methacrylate (MEO₂MA) and synthesized by free radical polymerization has been investigated. The homopolymer hydrogel presents a low critical solution temperature (LCST) close to room temperature, which can be modulated by copolymerization with longer oligo(ethylene glycol) side chain methacrylates (OEG_xMA). Then, three series of copolymeric hydrogels synthesized with MEO₂MA and several low ratios of OEG_xMA with M_n = 475 g mol⁻¹ (OEG₈MA), M_n = 1100 g mol⁻¹ (OEG₂₃MA) and M_n = 2080 g mol⁻¹ (OEG₄₅MA) were studied. In addition to conventional tetra(ethylene glycol) dimethacrylate (TEGDMA) crosslinker, the use of biodegradable oligo(caprolactone) dimethacrylate (OCLDMA) was also tested. The hydrophilic/hydrophobic balance, function of the short and the long OEG side chains, establishes a swelling behaviour depending on monomer composition, side chain length and temperature. The swelling at equilibrium increases with increasing the amount of OEG_xMA in the copolymer and, at the same time, the collapsing moves progressively to higher temperature. The temperature dependent volumetric response of some of these hydrogels can be compare with the most extended thermo-sensitive hydrogel, which is based on poly(N-isopropylacrylamide) (P(N-iPAAm)). Therefore, they are potential candidates to replace it in applications where biocompatibility is required.     

Effects of synthesis-solvent on swelling and elastic properties of poly(N-isopropylacrylamide) hydrogels

Thermosensitive N-isopropylacrylamide (NIPA) hydrogels were synthesized by a free radical copolymerization with N,N′-methylenebisacrylamide (MBAA) in four solvents: water, ethanol, acetone and N,N-dimethylformamide. The swelling and elastic properties of the hydrogels were affected by the synthesis-solvents; the hydrogels (e.g. NIPA/MBAA = 1000/50 mol/m³-pre-gel solution) synthesized in water have smaller swelling volume and larger shear modulus at 10 °C than those synthesized in amphiphilic solvents. The network structure of hydrogels was estimated in terms of the conversion and two sorts of effective crosslinking density based on the Flory theory and the concentration of crosslinker. The hydrogels synthesized in water can have the microscopic inhomogeneous network arising from the entanglement of polymer chains, while the hydrogels synthesized in amphiphilic solvents can have the homogeneous network arising from the polymer concentration lower than the pre-gel solution and can be similar in network structure to the lightly crosslinked hydrogel synthesized in water.     

Four-coordinate boron compounds derived from 2-(2-pyridyl)phenol ligand as novel hole-blocking materials for phosphorescent OLEDs

Four-coordinate boron compounds of Ph₂B · 1 (2) and (C₆F₅)₃B(1 · H) (3) were prepared from the reaction of 2-(2-pyridyl)phenol (1 · H) ligand with triarylborane starting materials, BPh₃ and B(C₆F₅)₃, respectively, and tested as hole-blocking layer (HBL) materials in phosphorescent OLEDs. While the crystal structure of 2 reveals the pseudo-tetrahedral geometry around the boron center with bidentate [N,O] chelation by 1, 3 is characterized as the zwitterionic four-coordinate system where the ligand 1 · H acts as monodentate [O] chelator with N-protonation. UV-Vis absorption and PL spectra of 2 and 3 are consistent with the ligand-centered, HOMO-LUMO electronic transitions with charge transfer from a phenoxide ring to a pyridine, which was further supported by time dependent DFT calculation for 2. Both compounds are found to possess the HOMO-LUMO energy gap of 3.1 eV appropriate for hole-blocking materials for phosphorescent OLEDs. The devices incorporating 2 and 3 as HBL materials displayed stable green phosphorescence of Ir(ppy)₃ (ppy = 2-phenylpyridine) with low turn-on voltage of 3.2 and 3.4 V, respectively, indicating that 2 and 3 function as HBL materials. Although both devices show the short lifetime (<1 h) probably owing to the low thermal stability, the device based on 2 displays better performances in terms of luminance, power and luminance efficiency, and external quantum efficiency in a wide range of current densities (0.1-100 mA/cm²) than the reference device incorporating BAlq as HBL materials.     

Water sorption and polymer dynamics in hybrid poly(2-hydroxyethyl-co-ethyl acrylate)/silica hydrogels

This work probes the hydration properties and molecular dynamics of hybrid poly(hydroxyethyl-co-ethyl acrylate)/silica hydrogels. Two series of hybrid copolymers were prepared by simultaneous polymerization and silica preparation by sol-gel method, the first with hydroxyethyl acrylate/ethyl acrylate (HEA/EA) composition at 100/0, 90/10, 70/30, 50/50, 30/70, 10/90 and fixed silica content at 20 wt.%, and the second with fixed HEA/EA organic composition at 70/30 and 0, 5, 10 and 20 wt.% of silica. The hydration properties of these systems were studied at 25 °C by exposure to several controlled water vapor atmospheres (water activities 0-0.98) in sealed jars and by immersion in distilled water. Finally, the molecular dynamics of the hydrated hybrids at several levels of hydration was probed with Thermally Stimulated Depolarization Currents (TSDC) in the temperature interval between −150 and 20 °C. The results indicate that a critical region of silica content between 10 and 20 wt.% exists, above which silica is able to form an inorganic network. This silica network prevents the expansion of water clusters inside the hydrogels and subsequently the total stretching of the polymer network without obstructing the water sorption at the first stages of hydration from the dry state. As concerns the copolymer composition, the presence of EA reduces water sorption and formation of water clusters affecting directly to the hydrophilic regions. The TSDC thermograms reveal the presence of a single primary main broad peak denoted as α_cop relaxation process, which is closely related to the copolymer glass transition, and of a secondary relaxation process denoted as β_sw relaxation, which originates from the rotational motions of the lateral hydroxyl groups with attached water molecules. The single α_cop implies structural homogeneity at the nanoscale in HEA-rich samples (x_HEA > 0.5), while for high EA content (x_EA ? 0.5) phase separation is detected. Both relaxation processes show strong dependence on water content and organic phase composition.     

Alkaline earth metal poly(hydrogen fluorides) hexafluoroarsenates(V) and hexafluorophosphate(V): M2(H2F3)(HF2)2(AF6) (M = Ca, A = As; M = Sr, A = As, P)

New compounds of the type M₂(H₂F₃)(HF₂)₂(AF₆) with M = Ca, A = As and M = Sr, A = As, P) were isolated. Ca₂(H₂F₃)(HF₂)₂(AsF₆) was prepared from Ca(AsF₆)₂ with repeated additions of neutral anhydrous hydrogen fluoride (aHF). It crystallizes in a space group P4₃22 with a = 714.67(10) pm, c = 1754.8(3) pm, V = 0.8963(2) nm³ and Z = 4. Sr₂(H₂F₃)(HF₂)₂(AsF₆) was prepared at room temperature by dissolving SrF₂ in aHF acidified with AsF₅ in mole ratio SrF₂:AsF₅ = 2:1. It crystallizes in a space group P4₃22 with a = 746.00(12) pm, c = 1805.1(5) pm, V = 1.0046(4) nm³ and Z = 4. Sr₂(H₂F₃)(HF₂)₂(PF₆) was prepared from Sr(XeF₂)_n(PF₆)₂ in neutral aHF. It crystallizes in a space group P4₁22 with a = 737.0(3) pm, c = 1793.7(14) pm, V = 0.9744(9) nm³ and Z = 4. The compounds M₂(H₂F₃)(HF₂)₂(AF₆) gradually lose HF at room temperature in a dynamic vacuum or during being powdered for recording IR spectra or X-ray powder ray diffraction patterns. All compounds are isotypical with coordination of nine fluorine atoms around a metal center forming a distorted Archimedian antiprism with one face capped. This is the first example of the compounds in which H₂F₃⁻ and HF₂⁻ anions simultaneously bridge metal centers forming close packed three-dimensional network of polymeric compounds with low solubility in aHF. The HF₂⁻ anions are asymmetric with usual F?F distances of 227.3-228.5 pm. Vibrational frequency (ν₁) of HF₂⁻ is close to that in NaHF₂. The anion H₂F₃⁻ exhibits unusually small F?F?F angle of 95.1°-97.6° most probably as a consequence of close packed structure.     

Swelling and network parameters of crosslinked thermoreversible hydrogels of poly(N-ethylacrylamide)

Samples of Poly(N-ethylacrylamide) (PEA) have been synthesized by free radical polymerization in water using N,N′-methylene bis-acrylamide (BIS) as crosslinker. Hydrogels obtained by swelling them in water, 15 wt% KCl and 1 wt% sodium dodecyl sulphate (SDS) were examined by gravimetric, dimensional and compression-strain measurements to afford values of swelling ratio, polymer-solvent interaction parameters, elastic moduli and effective crosslinking density ν_e. Crosslinking inefficiency is evidenced by the low value (0.23) of ν_e relative to the theoretical crosslinking density ν_t based on the content of BIS in the synthesis. A small but finite extrapolated value of ν_e at ν_t = 0 is indicative of hydrophobic physical interactions. In water at 298 K increasing the content of BIS leads to a decrease in swelling and increases in values of elastic moduli and polymer-water interaction parameter. At a fixed content of BIS the values of ν_e and the elastic moduli exhibit an unusual increase with temperature, the crosslinking thus being thermally reversible. It is proposed that this results from a balance between hydrophobic interaction and breakage of hydrophilic hydrogen bonding. Although KCl in the medium decreases the swelling compared with that in water, the opposite effect occurs on incorporation of SDS, which is assumed to confer some polyelectrolyte character to the PEA chains. The finding, that these two swelling media reduce the values of ν_e and elastic moduli cf the value in water, has not been resolved satisfactorily.     

Novel oxorhenium complexes with 2-(2′-hydroxyphenyl)-2-benzothiazolinato ligand: X-ray studies,spectroscopic characterization and DFT calculations

The [ReOX₂(hbt)(EPh₃)] (X = Cl, Br; E = As, P) chelates have been prepared in the reactions of [ReOX₃(EPh₃)₂] complexes (X = Cl, Br; E = P, As) with 2-(2′-hydroxyphenyl)-2-benzothiazole (hbtH) in acetone. From the reactions of [ReOX₃(PPh₃)₂] with hbtH two kind of crystals [ReOX₂(hbt)(PPh₃)] · MeCN and [ReOX₂(hbt)(PPh₃)] with different arrangement of halide ions (cis and trans) were isolated, whereas the [ReOX₃(AsPh₃)₂] oxocompounds react with hbtH to give only cis-halide isomers. The complexes were structurally and spectroscopically characterised. The electronic structures of both [ReOBr₂(hbt)(PPh₃)] isomers have been calculated with the density functional theory (DFT) method. The TDDFT/PCM calculations have been employed to produce a hundred of singlet excited-states starting from the ground-state geometry optimized in the gas phase of cis- and trans-halide isomers of [ReOBr₂(hbt)(PPh₃)] and the UV–Vis spectra of these complexes have been discussed on this basis.     

Poly(ester imide)s possessing low coefficients of thermal expansion (CTE) and low water absorption (III). Use of bis(4-aminophenyl)terephthalate and effect of substituents

A variety of poly(ester imide)s (PEsIs) were prepared using bis(4-aminophenyl)terephthalate (BPTP) and substituted BPTP (BPTP series) for applications to novel base film materials in flexible printed circuit boards (FPC). BPTP series were all highly reactive with various tetracarboxylic dianhydrides and led to considerably high molecular weights of PEsI precursors. The thermally imidized BPTP-based PEsI films achieved lower extents of water absorption (W_A) than the corresponding 4-aminophenyl-4′-aminobenzoate (APAB)-based PEsI systems while keeping other target properties, in particular, the linear coefficient of thermal expansion (CTE) much lower than that of copper foil as a conductive layer in FPC. The lower W_A is attributed to the decreased imide contents in the structure by using BPTP. The considerably low CTE can be explained in terms of intimate stacking between the p-aromatic ester fragments with an extended conformation. The BPTP-based PEsI system also exhibited a considerably low dissipation factor (tan δ = 1.91 × 10⁻³) at a high-frequency electric field of 18.3 GHz, comparable to a liquid-crystalline polyester. An effect of substituents on the film properties was also investigated in this work. Incorporation of methyl substituents on BPTP was very effective for property improvement, whereas methoxy substituents on BPTP, as well as methyl substituents onto hydroquinone bis(trimellitate anhydride) (TAHQ), showed a trend to significantly increase the CTE. Copolymerization with an adequate amount of a typically flexible monomer, 4,4′-oxydianiline (4,4′-ODA), allowed the CTE matching with copper foil and the film toughness improvement at the same time. The PEsI copolymer prepared from TAHQ (10 mmol) with methyl-substituted BPTP (7 mmol) and 4,4′-ODA (3 mmol) achieved excellent combined properties, namely, a very high T_g at 410 °C, a slightly lower CTE (10.0 ppm/K) than that of copper foil, suppressed water absorption (0.35%), an extremely low linear coefficient of humidity expansion (CHE = 3.4 ppm/RH%), and good film toughness (the elongation at break, ε_b = 50.7%). Thus, BPTP- and methyl-substituted BPTP-based PEsI systems can be promising candidates as a next generation of FPC base film materials.     

1-(2′-Pyridylazo)-2-naphtholate (PAN) complexes of rhodium(III): Synthesis,structure and spectral studies

The ligating properties 1-(2′-pyridylazo)-2-naphthol (HPAN) toward Rh(III) have been examined. The reaction of RhCl₃·3H₂O with HPAN in presence of excess PPh₃ afforded trans-[Rh(PAN)Cl(PPh₃)₂]PF₆ (3PF₆). Intermediate cis-[Rh(PAN)Cl₂(PPh₃)] (4) has also been isolated. Solid state structures were authenticated by X-ray analyses revealing that monoanionic PAN is coordinated to rhodium in meridional fashion. Both the compounds were spectroscopically characterized in both solution and solid states, which include IR, NMR (¹H and ³¹P), and optical spectra. The diamagnetic complexes show multiple CT transitions in the visible region. Low-energy transitions (λ ≈ 550–650 nm) occurred in the absorption spectra are predominantly ligand centered in nature. The rhodium(III)–PAN compounds are red emissive (λ_em ≈ 650 nm) at room temperature and the nature of the emission level is probably an ILCT level. Complexes are electro-active in acetonitrile and display irreversible oxidative and reductive waves and these responses are ascribed to be PAN ligand centered in character.     

Thermoresponsive poly(N-isopropylacrylamide) nanogels/poly(acrylamide) nanostructured hydrogels

Here we report the preparation and characterization of nanostructured thermo-responsive poly(acrylamide) (PAM)-based hydrogels. The addition of slightly crosslinked poly(N-isopropylacrylamide) (PNIPA) nanogels to AM reactive aqueous solution produces nanostructured hydrogels that exhibit a volume phase transition temperature (T_VPT). Their swelling kinetics, T_VPT's and mechanical properties at the equilibrium-swollen state (H_eq) are investigated as a function of the concentration of PNIPA nanogels in the nanostructured hydrogels. Nanostructured hydrogels with PNIPA nanogels/AM mass ratios of 20/80 and above exhibit higher H_eq and longer time to reach the equilibrium swelling than those of the conventional PAM hydrogels. However, the PNIPA nanogels possess thermo-responsive character missing in conventional PAM hydrogels. The T_VPT of nanostructured hydrogels depends on PNIPA nanogel content but their elastic and Young moduli are larger than those of conventional hydrogels at similar swelling ratios. Swelling kinetics, T_VPT, and mechanical properties are explained in terms of the controlled in-homogeneities introduced by the PNIPA nanogels during the polymerization.     

Synthesis, characterization and thermoreversible behaviours of poly(dimethyl siloxane)/poly(N-isopropyl acrylamide) semi-interpenetrating networks

Simultaneous and sequential poly(N-isopropyl acrylamide) (PNIPAAm)/poly(dimethyl siloxane) (PDMS) semi-interpenetrating polymer networks (IPNs) with different linear PDMS contents were prepared by free radical polymerization method. Their phase morphologies have been characterized by FTIR, DSC and SEM. The simultaneous semi-IPNs exhibited phase transition temperatures (T_pt) shifted higher temperature from glass transition temperatures (T_g) of their respective homopolymers, suggesting a heterophase morphology and only physical entanglement between the PNIPAAm network and linear PDMS with high molecular weight (Mn≈9000 g/mol). For sequential semi-IPNs, the shift of T_pts towards lower temperature suggested that the chemical interaction between the constituents of the IPNs increased with increasing PDMS content in the network. In addition, these semi-IPNs were characterized for their thermo-sensitive behaviour by equilibrium swelling studies. The results showed that incorporation of hydrophobic PDMS polymer into the thermo- and pH-sensitive PNIPAAm and P(NIPAAm-co-IA) (itaconic acid) hydrogels by semi-IPN formation decreased swelling degrees of IPNs without affecting their LCSTs whereas addition of acrylated PDMS (Tegomer V-Si 2250) as crosslinker instead of N,N^′-methylenebisacrylamide (BIS) into the structures of these hydrogels changed their LCSTs along with their swelling degrees.     

Rh-complexes of ditopic bis(pyrazol-1-yl)borate ligands: Assessment of their catalytic activity towards phenylacetylene polymerization

Two dinuclear Rh^I-cyclooctadiene complexes [1,4-(cod)Rh(B(R’)pz₂)-C₆H₄-(B(R’)pz₂)Rh(cod)], linked by a ditopic scorpionate ligand, have been prepared and fully characterized (R′ = Ph (2), C₆F₅ (2^F); pz = pyrazolide). Both compounds were tested as catalysts for phenylacetylene polymerization but showed no catalytic activity. Attempts at the synthesis of corresponding complexes of the sterically more demanding ligands (R′ = Ph (4), C₆F₅ (4^F); pz^Ph = 3-phenylpyrazolide) resulted in B-N bond cleavage and formation of the dinuclear complex [(cod)Rh(μ-pz^Ph)₂Rh(cod)] (5). Complex 5 proved to be an efficient catalyst for the preparation of highly stereoregular head-to-tail cis-transoidal poly(phenylacetylene).     

1-(2′-Pyridylazo)-2-naphtholate complexes of ruthenium: Synthesis,characterization, and DNA binding properties

Reaction of 1-(2′-pyridylazo)-2-naphthol (Hpan) with [Ru(dmso)₄Cl₂] (dmso = dimethylsulfoxide), [Ru(trpy)Cl₃] (trpy = 2,2′,2″-terpyridine), [Ru(bpy)Cl₃] (bpy = 2,2′-bipyridine) and [Ru(PPh₃)₃Cl₂] in refluxing ethanol in the presence of a base (NEt₃) affords, respectively, the [Ru(pan)₂], [Ru(trpy)(pan)]⁺ (isolated as perchlorate salt), [Ru(bpy)(pan)Cl] and [Ru(PPh₃)₂(pan)Cl] complexes. Structures of these four complexes have been determined by X-ray crystallography. In each of these complexes, the pan ligand is coordinated to the metal center as a monoanionic tridentate N,N,O-donor. Reaction of the [Ru(bpy)(pan)Cl] complex with pyridine (py) and 4-picoline (pic) in the presence of silver ion has yielded the [Ru(bpy)(pan)(py)]⁺ and [Ru(bpy)(pan)(pic)]⁺ complexes (isolated as perchlorate salts), respectively. All the complexes are diamagnetic (low-spin d⁶, S = 0) and show characteristic ¹H NMR signals and intense MLCT transitions in the visible region. Cyclic voltammetry on all the complexes shows a Ru(II)–Ru(III) oxidation on the positive side of SCE. Except in the [Ru(pan)₂] complex, a second oxidative response has been observed in the other five complexes. Reductions of the coordinated ligands have also been observed on the negative side of SCE. The [Ru(trpy)(pan)]ClO₄, [Ru(bpy)(pan)(py)]ClO₄ and [Ru(bpy)(pan)(pic)]ClO₄ complexes have been observed to bind to DNA, but they have not been able to cleave super-coiled DNA on UV irradiation.     

Mechanistic studies on the Pd–Cl cleavage of dichloro-[1-alkyl-2-(naphthylazo)imidazole]palladium(II) complexes by 8-quinolinol

8-Quinolinol (HQ) reacts with [Pd(α-/β-NaiR)Cl₂] [α-/β-NaiR = 1-alkyl-2-(naphthyl-α-/β-azo)imidazole] in acetonitrile (MeCN) solution to give [Pd(α-/β-NaiR)(Q)](ClO₄). The products are characterized by spectroscopic techniques (FT-IR, UV–Vis, NMR). The reaction kinetics show a first order dependence of rate on each of the concentration of the metal complex and HQ. Addition of LiCl to the reaction retarded the rate of reaction and has proved the cleavage of the Pd–Cl bond as the rate-determining step. Thermodynamic parameters (Δ^‡H^° and Δ^‡S^°) are determined from variable temperature kinetic studies. The magnitude of the second order rate constant, k₂, increases as in the order: Pd(NaiEt)Cl₂ < Pd(NaiMe)Cl₂ < Pd(NaiBz)Cl₂ as well as Pd(β-NaiR)Cl₂ < Pd(α-NaiR)Cl₂.     

Reactivity studies of cyclopentadienyl ruthenium(II), osmium(II) and pentamethylcyclopentadienyl iridium(III) complexes towards 2-(2′-pyridyl)imidazole derivatives

The reaction of [CpRu(PPh₃)₂Cl] and [CpOs(PPh₃)₂Br] with chelating 2-(2′-pyridyl)imidazole (N ∩ N) ligands and NH₄PF₆ yields cationic complexes of the type [CpM(N ∩ N)(PPh₃)]⁺ (1: M = Ru, N ∩ N = 2-(2′-pyridyl)imidazole; 2: M = Ru, N ∩ N = 2-(2′-pyridyl)benzimidazole; 3: M = Ru, N ∩ N = 2-(2′-pyridyl)-4,5-dimethylimidazole; 4: M = Ru, N ∩ N = 2-(2′-pyridyl)-4,5-diphenylimidazole; 5: M = Os, N ∩ N = 2-(2′-pyridyl)imidazole; 6: M = Os, N ∩ N = 2-(2′-pyridyl)benzimidazole). They have been isolated and characterized as their hexafluorophosphate salts. Similarly, in the presence of NH₄PF₆, [Cp∗Ir(μ-Cl)Cl]₂ reacts in dry methanol with N ∩ N chelating ligands to afford in excellent yield [Cp∗Ir(N ∩ N)Cl]PF₆ (7: N ∩ N = 2-(2′-pyridyl)imidazole; 8: N ∩ N = 2-(2′-pyridyl)benzimidazole). All the compounds have been characterized by infrared and NMR spectroscopy and the molecular structure of [1]PF₆, [2]PF₆ and [7]PF₆ by single-crystal X-ray structure analysis.     

Potentiometric membrane sensor based on 6-(4-nitrophenyl)-2,4-diphenyl-3,5-diaza-bicyclo[3.1.0]hex-2-ene for detection of Sn(II) in real samples

A Sn²⁺ ion-selective electrode which was prepared with a polymeric membrane based on 6-(4-nitrophenyl)-2,4-diphenyl-3,5-diaza-bicyclo[3.1.0]hex-2-ene (NDDBH) as a ionophore. Effects of experimental parameters such as membrane composition, nature and amount of plasticizer, the amount of additive and concentration of internal solution on the potential response of Sn²⁺ sensor were investigated. The electrode exhibited a Nernstian slope of 28.8 ± 1.1 mV/decade of Sn²⁺ over a concentration range of 1.0 × 10⁻⁵ to 1.0 × 10⁻¹ M of Sn²⁺ in an acidic solution (pH 1). The limit of detection was 4.0 × 10⁻⁶ M. The results show that this electrode can be used in ethanol media until 20% (v/v) concentration without interference. It can be used for more than 6 weeks without any considerable divergence in the potentials. The proposed membrane electrode revealed very good selectivity for Sn(II) ions over a wide variety of other cations and could be used in acidic media. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the electrode. The stability constant (log K_s) of the Sn(II)-ionophore complex was determined at 25 °C by potentiometric titration in mixed aqueous solution. It was used as indicator electrode in potentiometric determination of Sn(II) ion in real samples.