硅丙微乳液共聚物胶膜的热性能

硅丙微乳液共聚物胶膜的热性能;硅氧烷; 丙烯酸酯; 微乳液热分析     

粘土/聚烯烃纳米复合材料研究进展

原位聚合;插层复合;粘土/聚烯烃纳米复合材料研究进展     

聚酰胺/粘土纳米复合材料

聚酰胺／粘土纳米复合材料是一种新型的有机－无机纳米复合材料。在无机物含量远少于常规填充复合材料的情况下就可以具有较好的力学性能、阻隔性能等,热稳定性能也显著提高,并具有阻燃性和各向异性。是一种性能优异的、具有广泛应用前途的纳米复合材料。综述了该纳米复合材料的制备、性能和应用前景等。     

硅丙乳液的表征、性能及其在模拟病害壁画修复中的应用北大核心CSCD

为了在理论上建立起一套完整、客观的性能评价方法,对硅丙乳液的颗粒尺寸、热稳定性、结构和形貌进行了表征,测定了乳液质量分数与其粘度、表面张力等关系。通过用硅丙乳液修复模拟起甲和酥碱的壁画,进一步验证乳液的性能。结果表明,硅丙乳液属于非晶态(无定形态)结构,乳胶粒子形貌接近球形,平均粒径为190 nm,颗粒无团聚现象,较小的粒径可以提高乳液的渗透能力;Si—O—Si键的引入有效提高了硅丙乳液的热稳定性和耐热老化性;随着硅丙乳液质量分数的增大,表面张力下降,相对粘度升高;硅丙乳液的机械稳定性、贮存稳定性、热稳定性和耐盐性较好。硅丙乳液在修复起甲、酥碱壁画后,分别循环20和12次老化,颜料层未发生显著差异,说明硅丙乳液可以作为一种性能优异的胶凝材料用于起甲、酥碱壁画的修复中。     

反相微乳液模板原位聚合制备纳米氯化银/聚甲基丙烯酸甲酯及其结构表征

用甲基丙烯酸甲酯(MMA)作油相,反相胶束微乳液作为模板,制备了纳米氯化银(AgCl)粒子,再进行原位聚合制备了纳米氯化银/聚甲基丙烯酸甲酯(AgCl/PMMA)复合材料.透射电镜(TEM)分析表明,纳米AgCl的尺寸为20～80 nm.扫描电镜(SEM)测试表明纳米AgCl粒子均匀地存在于PMMA基材中.红外分析证明,胶束中水和表面活性剂AOT的羰基在MMA聚合后微观环境发生变化,纳米粒子同聚合物之间有吸附行为.动态力学(DMTA)分析复合材料,发现纳米AgCl粒子与聚合物之间存在强烈相互作用,形成了中间相层(interphase layer),改变了聚合物的动态力学性能.     

室温交联型硅丙微胶乳的合成研究Ⅲ.聚合工艺对聚合稳定性及胶膜性能的影响

采用两种聚合工艺(种子微乳液聚合法和单体预乳化法)分别合成了室温交联型有机硅改性丙烯酸酯聚合物微胶乳，研完了不同工艺条件对聚合稳定性、乳胶粒径和胶膜的结构性能的影响．     

聚酰胺／粘土纳米复合材料的掉备,结构表征及性能研究

聚酰胺／粘土纳米复合材料，由于粘土以纳米悄度均匀地分散在聚酰胺基体中以及粘土与基体间强的化学结合，较常规填充增强聚酰胺复合材料具有更高强度，模量，耐热，气体阻隔等性能，是一种性能优异的聚酰胺材料，本文重点综述了混杂材料的制备，结构表征，特殊的界面相互作用，力学性能，结晶行为及结晶动力学等方面的研究，并展望了该材料的应用前景。     

W／O型乳液的稳定性和水St—DVB乳液悬浮聚合白球的孔结构研究

研究了乳化剂PAG和SPAN复配比例以及某些二价金属离子对W/O型乳液稳定性的影响,同时也研究了St—DVB水乳液的悬浮聚合条件和白球的孔结构。结果表明,水相中存在微量的Mg~(2+)或Zn~(2+),并用适当比例的PAG和SPAN80配制的W/O型乳液具有较好的稳定性;St—DVB水乳液通过悬浮聚合制得的白球部份地具有类似田垄状的孔道结构。     

有机硅改性丙烯酸酯乳液的流变性

聚合物乳液;流变性能;反应性乳液;有机硅改性丙烯酸酯乳液的流变性     

硅丙型核壳结构乳胶粒子的制备及成膜过程

采用分步乳液聚合方法, 分别在不同步骤中将乙烯基硅氧烷单体作为共聚单体引入聚丙烯酸酯类乳液共聚合体系中, 制备出具有窄分布多层核壳结构形态的硅丙型乳胶粒子. 利用透射电子显微镜(TEM)表征, 乳胶粒子具有硅丙型核壳结构; 动态激光散射(DLS)分析得到的乳胶粒子的直径与TEM数据相符; 同时由多频调制差示扫描量热(TOPEM-DSC)技术分析得到的乳胶粒子的3个玻璃化转变温度与实验设计相符, 证实乳液粒子的核壳结构; 利用Horus成膜仪对乳胶粒子成膜过程进行全程监控. 利用多种助剂制得水性木器涂料, 其漆膜的硬度、耐丙酮性、耐水性、耐醇性及耐压痕等性能优异.     

High Solids Content,Soap‐Free,Film‐Forming Latexes Stabilized by Laponite Clay Platelets

High solids content film‐forming poly[styrene‐co‐(n‐butyl acrylate)] [poly(Sty‐co‐BuA)] latexes armored with Laponite clay platelets have been synthesized by soap‐free emulsion copolymerization of styrene and n‐butyl acrylate. The polymerizations were performed in batch in the presence of Laponite and a methyl ether acrylate‐terminated poly(ethylene glycol) macromonomer in order to promote polymer/clay association. The overall polymerization kinetics showed a pronounced effect of clay on nucleation and stabilization of the latex particles. Cryo‐transmission electron microscopy observation confirmed the armored morphology and indicated that the majority of Laponite platelets were located at the particle surface. The resulting nanostructured films displayed enhanced mechanical properties.

     

Structural and Chemical Modification of Polydiene Latexes by Gel Derived Silica

Latex-silicate compositions and unsupported films (green and vulcanized) were prepared by mixing natural Qualitex and synthetic butadiene-styrene (SKSS) latexes with an aqueous solution of sodium silicate modified with a zinc tetrammine complex. The mechanism and efficiency of the inorganic modification of latex structures were investigated by UV-vis and IR spectrophotometry, rotational viscometry of liquid and gelled mixtures as well as by tensile testing of the prepared films. Measurements showed an increase of elastic modulus and tensile strength with silica concentration for all composite films except for the green SKSS-based ones. The improvement of mechanical properties can be related to the formation of interpenetrating organic and silicate networks linked by Zn atoms that can also participate in the vulcanization process.     

核／壳型聚硅氧烷丙烯酸酯复合乳液的制备

采用种子乳液聚合的方法制备了具有核／壳结构的聚硅氧烷丙烯酸酯复合乳液，考察了乳化剂、单体的加入方式及配比对产生乳液粒子的影响。结果表明，乳化剂在核阶段和壳阶段的单体聚合中都起着很重要的作用，当乳化剂分子在乳液粒子上的覆盖率低于４０％时，可制得较理想的核／壳型复合乳液。     

High Solid Acrylic–Melamine Latexes with Tunable Crosslinking Capability

Miniemulsion polymerization is employed to produce high solid content (50%) acrylic/melamine latexes with varied crosslinking capability, for their potential application as waterborne crosslinkable coatings. This synthesis strategy allows the efficient incorporation of a hydrophobic crosslinker, iso‐butylated melamine (iBMF), into polymer particles, and to obtain latexes with different iBMF concentrations and acrylic polymer with varied content of hydroxylic groups (OH–). The involved crosslinking mechanisms and the physical transformations during film thermosetting of acrylic/iBMF nanocomposite are exhaustively investigated by combining thermal, spectroscopic, and thermo‐mechanical analyses. The influence of reactive groups concentration (iBMF and OH– content in the acrylic polymer) on the rate of curing, the crosslinking degree, and consequently onto the sensitive properties of cured films are discussed here.     

用于制备聚氨酯纳米复合物的高岭石粒子的表征

Clay such as kaolinite， is commonly used as an additive to modify the thermal properties of polymer. In this paper， the morphology， composition， shape and structure of kaolinite was characterized by various advanced techniques. The TEM/ EDX data showed that the kaolinite had a larger particle size and a Si/Al ratio of 1.8. The individual particle of kaolinite was a single crystalline. TEM also showed that these particles were always stacked together due to the presence of electrostatic cohesive energy and hydrogen bond between plaletes. The PAS-FTIR spectra showed that no absorbance of hydroxyl group for hydration water in hydrogen bond region or at 1650cm^-1 was observed at room temperature. It meant a little ability to adsorb water for kaolinite particle. Kaolinite clay also showed no change for its PAS-FTIR spectra with increasing temperature. The TGA results revealed that kaolinite almost doesn′t lose weight at 60℃ due to loss of dehydration of absorbed water， however， it will decomposed around 510℃ and lose its hydroxyl functional group in the form of water (dehydroxylation). The result is consistent with that of PAS-FTIR analysis. This suggests that the structural hydroxyl group on the surface of individual kaolinite clay particle is very stable below 500℃， and the kaolinite composed polymer could be got by the reaction of its stable structural hydroxyl group with isocynate group of polyurethane prepolymer.     

Synthesis of Exfoliated MEH-PPV/Clay Nanocomposites

The synthesis of poly（2-methoxy-5-（2＇-ethyl-hexyloxy）-l,4-phenylenevinylene） （MEH-PPV） in the presence of organophilic montmorillonite （OMMT） was reported and the exfoliated MEH-PPV/OMMT nanocomposites was obtained by controlling the ratio of the monomer to the OMMT.     

An Emulsifier‐Free RAFT‐Mediated Process for the Efficient Synthesis of Cerium Oxide/Polymer Hybrid Latexes

Hybrid latexes based on cerium oxide nanoparticles are synthesized via an emulsifier‐free process of emulsion polymerization employing amphiphatic macro‐RAFT agents. Poly(butyl acrylate‐co‐acrylic acid) random oligomers of various compositions and chain lengths are first obtained by RAFT copolymerization in the presence of a trithiocarbonate as controlling agent. In a second step, the seeded emulsion copolymerization of styrene and methyl acrylate is carried out in the presence of nanoceria with macro‐RAFT agents adsorbed at their surface, resulting in a high incorporation efficiency of cerium oxide nanoparticles in the final hybrid latexes, as evidenced by cryo‐transmission electron microscopy.     

Alkoxysilane Functional Acrylic Latexes: Influence of Copolymer Composition on Self-Curing Behavior and Film Properties

Reactive latexes based on acrylic polymers with trimethoxysilyl groups in the side chain were prepared by semi-continuous emulsion copolymerization. The properties of the latex film related to the polymer network structure and their evolution upon thermal curing were studied as a function of the content of the reactive comonomer, trimethoxysilylpropyl methacrylate (TSPMA), ranging between 8 and 25 wt-%. In particular, the sensitivity to both organic solvent (chloroform) and water and the thermomechanical properties were investigated by swelling experiments and dynamic-mechanical analysis (DMA). The results are interpreted in terms of a transition from uniform to microheterogeneous crosslinking regime, possibly as the result of formation of polyorganosilsesquioxane-like (POSS) crosslinking domains at higher TSPMA content.     

有机硅改性丙烯酸酯共聚乳液合成方法及胶膜性能的研究

用一次投料法、单体乳液滴加法和引发剂滴加法有机硅改性丙烯酸酯共聚乳液，聚合过程、胶粒形态及乳液稳定性的观测结果表明：单体乳液滴加法是合成该类乳液的最佳方法，研究了单体乳液滴加法中有机硅含量与聚合反及胶膜性能的关系，结果表明：有机硅含量在１５％以下时，聚合反应可以顺利进行，胶膜性能不仅依赖于聚合时有机硅单体的总量，而且还依赖于有机硅单体中活性硅氧烷所占的比例。     

Preparation of Thermochromic Films from Latexes Made by Miniemulsion Polymerization

Thermosensitive‐thermochromic pigments are classified as smart materials capable of detecting and/or responding to environmental stimuli, and specifically in this study, changes in temperature that induce a change in the color of the material. This study aims to obtain nanoparticles of poly(styrene‐co‐butyl acrylate) and poly(styrene‐co‐methyl methacrylate), containing thermosensitive‐thermochromic pigments that are incorporated into the monomer droplets in miniemulsion polymerization. Miniemulsion polymerization has the advantage that the pigment particles can be dispersed directly in the monomer droplets and are encapsulated when the miniemulsion droplets are polymerized. Using controlled/living radical polymerization (or Reversible Deactivation Radical Polymerization), it is possible to produce polymers with better control of microstructure and narrower molecular weight distributions. Nitroxide‐mediated polymerization (NMP) is conducted using the BlocBuilder initiator, as well as a conventional free radical polymerization (FRP) using potassium persulfate (KPS) and 2,2‐azobis(2‐methylpropionitrile) (AIBN). Stable latexes containing the thermosensitive‐thermochromic pigments are obtained by both NMP and FRP. Films are made from the latexes and shown to exhibit thermochromic behavior.