A REVIEW OF OXYGEN-CONTAINING SURFACE GROUPS AND SURFACE MODIFICATION OF ACTIVATED CARBON

This review focused on the recent reports related to the function, characterization and modification of axygen-containing surface groups of activated carbon (AC). The Oxygen-containing surface groups were briefly described, and the most frequently used techniques for characterization of the oxygen-containing surface groups on .ACs were also briefly stated .4 detailed discussion of the effects of the oxygen-containing snrface groups on the adsorptive capacity of .4C was given. The recent progresses in modification of the oxygen-containing surface groups of AC were also reviewed     

EFFECT OF HYPERCROSSLINKED RESINS SURFACE CHEMISTRY ON THE ADSORPTION OF PHENOL FROM AQUEOUS SOLUTION

Two hypercrosslinked resins with similar physical characters but different surface chemistry were synthesized and used to remove phenol from aqueous solutions. The FTIR spectra, elemental analysis and the Boehm titration were used to characterize the chemical properties of the resins. The adsorption experiments were carried out using the bottle-point technique, and the effects of the surface chemistry on the adsorption were discussed. The adsorption data fit well with the Freundlich model, indicating the heterogeneity of the resins surface. It could be seen from the experimental results that the adsorption capacity increased with the increase in the total surface concentration of oxygen-containing groups. The pH dependence and the effects of ionic strength were also discussed. The kinetic adsorption data fit well with the pseudo-second order model, and the results showed that the surface oxygen-containing groups have little effect on the adsorption rate.     

神木煤显微组份的表面特性

煤表面亲水性是影响水煤浆(CWS)流变性能的重要因素。关于表面活性剂和煤岩组成对煤亲水性影响的研究比较少,本文在这方面进行了一些工作,旨在弄清神木煤配CWS的制约因素。1.实验部分煤样采自神府煤田神木区四门沟矿3~(-1)层。用手选法选出镜煤和丝炭,经破碎、筛分制成80—180目研究样品。     

过硫酸铵水溶液对聚乙烯表面作用的研究

本文利用X光电子能谱(XPS)及其它技术对过硫酸铵水溶液处理聚乙烯表面改进粘合性的作用机理进行了研究。结果表明,过硫酸铵的氧化作用使聚乙烯表面引入酮、醛、羧基等含氧基团,使其粘合强度显著提高。高密度聚乙烯表面的氧化深度小于40,低密度聚乙烯的均匀氧化深度在40—90之间。处理后的聚乙烯表面未发现明显的交联产物。     

椰壳活性炭氧化后负载硅基复合氧化物低温脱硝催化剂的研究

椰壳活性炭经硝酸氧化处理后做载体,采用浸渍法负载含SiO_2的复合氧化物,用做低温脱硝催化剂.在锰氧化物中添加Ti O2,可以提高催化剂的抗硫性能,但低温脱硝活性降低.然而在锰氧化物中添加SiO_2,不仅提高了催化剂的抗硫性能,而且也提高了脱硝活性.TEM结果表明加入SiO_2可以有效的减小复合氧化物晶粒尺寸,更提高了其在载体上的分散度.NH_3-TPD结果显示加入SiO_2后催化剂表面酸性显著增强.XPS分析发现加入SiO_2还增大了催化剂表面Mn~(4+)的相对含量.此外,经硝酸氧化处理过的椰壳活性炭,表面含氧基团增加,从而也大大提高了对NH_3及NO的吸附容量.在相同脱硝条件下,与原料活性炭负载的催化剂比较,硝酸氧化处理后的活性炭负载的催化剂具有更高的脱硝效率.     

活性炭表面含氧基团的生成及对NO的还原作用

活性炭表面含氧基团的生成及对ＮＯ的还原作用＊高志明杨向光吴越＊＊（中国科学院长春应用化学研究所，长春１３００２２）关键词活性炭，一氧化氮，氧化铜，还原，氧化近几年，随着环保研究的开展，活性炭被用于同时脱硫脱硝反应［１］．活性炭的表面化学性质就成为需要...     

对甲苯磺酸/活性炭/双氧水体系选择氧化苯乙烯生成苯甲醛(英文)

以双氧水为氧化剂,研究了对甲苯磺酸和活性炭体系选择氧化苯乙烯生成苯甲醛反应性能。考察了反应时间、温度、催化剂用量、苯乙烯和双氧水摩尔比等对苯乙烯选择氧化性能的影响.结果表明,对甲苯磺酸和活性炭的用量和用量比是一个重要因素,但对甲苯磺酸的酸性对氧化反应活性影响不大.对甲苯磺酸和双氧水相互作用,经非自由基过程氧化苯乙烯.通过分解双氧水产生氢氧自由基,活性炭显著提高对甲苯磺酸和双氧水体系氧化苯乙烯活性.在惰性或还原气氛中高温处理活性炭能降低其表面含氧基团数量,增加碱性,有效分解双氧水,产生相对较多的OH自由基.与未处理的活性炭相比,高温处理的活性炭进一步提高了对甲苯磺酸和双氧水体系氧化苯乙烯活性,但降低了苯甲醛选择性.经磺化,在活性炭表面引入的–SO_3H基团比含氧基团(–OH,–COOH)更有效与双氧水作用氧化苯乙烯.     

活性炭的表面含氧官能团及其对吸附影响的研究进展

对活性炭表面含氧官能团的种类,生成原因以及活性炭含氧官能团的定性定量分析方法进行了综述。含氧官能团改变了活性炭的表面性质和表面行为,导致活性炭对金属离子和有机物的吸附性能发生变化,介绍了吸附金属离子和有机物时含氧官能团参与的作用机理,并对含氧官能团影响的研究提出了一些建议。     

Influence of surface functionalization via chemical oxidation on the properties of carbon nanotubes

The surface of carbon nanotubes (CNTs) was functionalized in different chemical oxidants, hydrogen peroxide, mixed concentrated HNO(3)/H(2)SO(4) and acidic KMnO(4) solution. The influences on the properties of CNTs were systematically investigated, such as the structure, the kinds and the contents of the formed surface oxygen-containing functional groups, the pH(PZC) values and the surface hydrophilicity using XRD, HREM, FTIR and chemical titration. The results show that the kinds and the contents of the surface oxygen-containing groups are dependent on the functionalization methods. The formation of the oxygen-containing groups can decrease pH(PZC) values and improve surface hydrophilicity of CNTs. The dispersion of the supported Pd-Pt particles on the functionalized CNTs and their catalytic activity in the profile reaction of naphthalene hydrogenation to tetralin are both promoted due to the presence of these oxygen-containing groups.     

3种酸氧化法制备的功能化多壁碳纳米管中含氧官能团含量的比较

通过定量测定碳纳米管表面含氧官能团对其功能化程度进行了评估.采用3种方法制备了酸氧化多壁碳纳米管(c-MWNTs),并对比了其分散稳定性,通过扫描电镜(SEM)和红外光谱法(FTIR)对其进行定性表征,分别用NaHCO3,Na2CO,及NaOH选择性地与c-MWNTs表面不同的酸性位点发生反应,利用酸碱滴定法定量测定其...     

聚醚硅油表面迁移行为对聚苯乙烯表面极性的影响

利用变角衰减全反射傅立叶变换红外光谱(ATR-FTIR)法和接触角,分析了聚醚硅油在聚苯乙烯共混物薄膜表面的选择性富集行为及对其表面结构和表面极性的影响,认为接触介质的表面性质是影响共混物中各组分产生选择性迁移扩散的重要影响因素.强极性介质的诱导作用可以在共混物表面层中产生剧烈变化的浓度梯度,而弱极性介质所产生的表面浓度梯度比较缓和.     

多壁碳纳米管的纯化及其表面含氧基团的表征

用兼具酸性和氧化性的HNO3水溶液可方便地除去残留在原生态多壁碳纳米管(CNT)上的Ni-MgO催化剂组分,同时在其表面产生某些含氧官能团,使原生态多壁碳纳米管的疏水性表面变为亲水性表面.采用Boehm中和滴定法以及X射线衍射(XRD)、热脱附谱(TPD)、傅里叶变换红外(FTIR)光谱和X射线光电子能谱(XPS)等技术对HNO3处理过的多壁碳纳米管的相组成和表面含氧官能团进行测量和表征.结果表明:所生成表面含氧官能团的总量以经7.0mol·L-1硝酸378K处理24h的CNT为最高;3种主要表面含氧官能团的含量高低顺序为,羧基内酯型羧基酚型羟基.     

pH-dependence of pesticide adsorption by wheat-residue-derived black carbon

The potential of black carbon as an adsorbent for pesticides in soils may be strongly influenced by the properties of the adsorbent and pesticides and by the environmental conditions. This study evaluated the effect of pH on the adsorption of diuron, bromoxynil, and ametryne by a wheat (Triticum aestivum L.) residue derived black carbon (WC) as compared to a commercial activated carbon (AC). The pH drift method indicated that WC had a point of zero charge of 4.2, much lower than that of 7.8 for AC. The density of oxygen-containing surface functional groups, measured by the Boehm titration, on WC was 5.4 times higher than that on AC, resulting in a pesticide adsorption by WC being 30-50% of that by AC, due to the blockage of WC surface by the waters associated with the functional groups. A small decrease (5.5%/unit pH) in diuron adsorption by WC with increase in pH resulted from increased deprotonation of surface functional groups at higher pH values. A much larger decrease (14-21%/unit pH) in bromoxynil adsorption by WC with increase in pH resulted from the deprotonation of both the adsorbate and surface functional groups of the adsorbent. The deprotonation reduced the adsorptive interaction between bromoxynil and the neutral carbon surface and increased the electrical repulsion between the negatively charged WC surface and bromoxynil anions. Deprotonation of ametryne with increase in pH over the low pH range increased its fraction of molecular form and thus adsorption on WC by 15%/unit pH. Further increase in pH resulted in a 20%/unit pH decrease in ametryne adsorption by WC due primarily to the development of a negative charge on the surface of WC. The pH-dependent adsorption of pesticides by black carbon may significantly influence their environmental fate in soils.     

Adsorption of ammonia and water on functionalized edge-rich carbon nanofibers

The preparation, characterization and ammonia and water adsorption properties of edge-rich carbon nanofibers (CNFs) were studied, including platelet CNFs (PCNFs) and cup-stacked CNFs (CSCNFs). Since PCNFs and CSCNFs have many chemically active exposed edges, functionalization by oxidizing the edges was carried out by ozone stream and by nitric acid. Transmission electron microscopy, N₂ adsorption isotherms and temperature-programmed desorption analysis showed that the nitric acid treatment partly destroyed the graphite structure of the PCNFs and created acid functional groups and micropores, whereas the ozone treatment created functional groups without damaging the structure. Ammonia adsorption isotherms clarified that NH₃ adsorption on PCNFs and CSCNFs occurred mainly on oxygen-containing groups, whereas the adsorption on activated carbon fibers (ACFs) occurred on both oxygen-containing groups and the carbon surface without the functional groups, and the CSCNFs showed larger amounts of adsorbed ammonia compared to the PCNFs. Especially at a relatively low pressure range (<0.2 atm), the PCNFs/CSCNFs/ACFs showed the same ammonia adsorption mechanism; that is, the one-to-one interaction between oxygen atoms in the functional groups and hydrogen atoms in ammonia molecules. In addition, the adsorption on the ACFs appeared to occur mainly by interaction with the carbon surface at relatively high pressure (0.3–1.0 atm). Our experimental results and previous findings suggest that NH₃ adsorption on PCNFs is due mainly to NH…O hydrogen bonding between oxygen-containing groups and ammonia rather than to chemical bonding.     

Adsorption of valeric acid from aqueous solution onto activated carbons: role of surface basic sites

Adsorption of valeric acid was studied on two activated carbons of different origins, wood and bituminous coal. The effect of oxidation on the adsorption uptake was investigated. Both initial samples were oxidized with nitric acid, which caused the introduction of a significant number of oxygen-containing groups onto the carbon surface. Boehm titration, potentiometric titration, thermal analysis, and sorption of nitrogen were used for detailed surface characterization. Valeric acid adsorption from aqueous solution was measured at 333 K. The calculated isotherms showed a good fitting to the Freundlich equation. The capacity coefficients revealed a direct correlation with the number of basic groups present on the surface. The amount of valeric acid adsorbed at its low concentration is dependent on the number of basic groups, whereas at high concentration the amount adsorbed depends on the volume of micropores smaller than 10 A, where the adsorption potential is the strongest.     

Adsorption of Cd(II) ion and its complex compounds from solution on the surface of charcoal treated with an oxidation-negative ionizing method

The adsorption characteristics of Cd(II) from electrolytic solution by activated charcoal have been investigated. It was found that the amount of adsorption of Cd(II) depends mainly on the pH value of the solution, the number of added inorganic ions, and oxygen-containing groups on the surface. The activated charcoal was treated with the oxidation-negative ionizing (OA) method to produce more oxygen-containing groups on the surface. The adsorption amount of Cd(II) on the treated activated charcoal increased remarkably. It was also found that the more powerful the acidity of the surface and the larger the adsorption amount of Cd(II), so the charged groups on the surface of activated charcoal are considered as the main adsorption-activated sites for inorganic ions. The adsorption characteristics of various complexes of Cd(II) on the surface of activated charcoal have also been investigated. Three types of adsorption configuration of the complexes of Cd(II) on the surface of activated charcoal were suggested according to the experimental results.     

碳纳米纤维的酸处理及其负载Pd-Pt的催化萘加氢活性

采用浓硝酸和浓硫酸混和液(90、120、150 ℃)处理鱼骨类和平行类碳层排布的碳纳米纤维. 运用高分辨电镜、红外光谱和离子交换对碳纳米纤维的表面性质进行了表征，并考察了以两种碳纳米纤维为载体的Pd-Pt催化萘加氢活性. 结果表明，碳纳米纤维的碳层排布不同使混酸处理的鱼骨类表面生成的极性含氧基团的量明显高于平行类表面，以前者为载体得到Pd-Pt催化剂金属颗粒的分散程度明显高于后者，其负载的Pd-Pt催化萘加氢活性也较高.     

SURFACE RHEOLOGY OF POLYMERIC SOLIDS

Surface molecular motions of amorphous polymeric solids have been directly measured on the basis of scanningviscoelasticity microscopic (SVM) and lateral force microscopic (LFM) measurements. SVM and LFM measurements werecarried out for films of conventional monodisperse polystyrene (PS) with sec-butyl and proton-terminated end groups atroom temperature. In the case of the number-average molecular weight, M_n, less than ca. 4.0×10~4, the surface was in a glass-rubber transition state even though the bulk glass transition temperature, T_g was far above room temperature, meaning thatthe surface molecular motion was fairly active compared with that in the bulk. LFM measurements of the, monodisperse PSfilms at various scanning rates and temperatures revealed that the time-temperature superposition was applicable to thesurface mechanical relaxation behavior and also that the surface glass transition temperature, T_g~σ, was depressed incomparison with the bulk one even though the magnitude of M_n was fairly high at 1.40×10~5. The surface molecular motionof monodisperse PS with various chain end groups was investigated on the basis of temperature-dependent scanningviscoelasticity microscopy (TDSVM). The T_g~σs for the PS films with M_n of 4.9×10~6 to 1.45×10~6 measured by TDSVMwere smaller than those for the bulk one, with corresponding M_ns, and the T_g~σs for M_ns smaller than ca. 4.0×10~4 were lowerthan room temperature (293 K). The active thermal molecular motion at the polymeric solid surface can be interpreted interms of an excess free volume near the surface region induced by the surface localization of chain end groups. In the case ofM_n=ca. 5.0×10~4, the T_g~σs for the α, ω-diamino-terminated PS (α,ω-PS(NH_2)_2) and α, ω-dicarboxy-terminated PS (α, ω-PS(COOH)_2) films were higher than that of the PS film. The change of T_g~σ for the PS film with various chain end groups canbe explained in terms of the depth distribution of chain end groups at the surface region depending on the relativehydrophobicity.     

聚苯乙烯胶乳的表面电性质与表面活性离子的吸附

根据电泳与电导的测量得出,聚苯乙烯胶乳质点的ξ电势随电解质浓度增加而变大,主要是质点表面基团与溶液间离子交换的结果。根据Langmuir吸附公式与Stern双电层模型,由电泳数据求出了表面活性阳离子在聚苯乙烯胶乳上的吸附自由能与吸附位数。增大电解质浓度使质点表面吸附位数增加,表面活性阳离子的吸附量也因此变大。     

SURFACE REARRANGEMENTS OF OXYGEN PLASMA TREATED POLYSTYRENE： SURFACE DYNAMICS AND HUMIDITY EFFECT

The time evolution of oxygen plasma treated polystyrene(PS)surfaces was investigated upon storing them in theair under controlled humidity conditions.The methods of water contact angle,X-ray photoelectron spectroscopy(XPS),sumfrequency generation(SFG)vibrational spectroscopy,and atomic force microscopy(AFM)were used to infer the surfaceproperties and structure.Chemical groups containing oxygen were formed on the PS surface with the plasma treatment,demonstrated by water contact angle and XPS.The surface polarity decayed markedly on time,as assessed by steady increasein the water contact angle as a function of storage time,from zero to around 60°.The observed decay is interpreted as arisingfrom surface rearrangement processes to burying polar groups away from the uppermost layer of the surfaces,which is incontact with air.On the other hand,XPS results show that the chemical composition in the first 3 nm surface layer isunaffected by the surface aging,and the depth profile of oxygen is essentially the same with time.A possible change of PSsurface roughness was examined by AFM,and it showed that the increase of water contact angle during surface aging couldnot be attributed to surface roughness.Thus,it is concluded that surface aging is attributable to surface reorganization andthe motion of oxygen containing groups is confined within the XPS probing depth.SFG spectroscopy,which is intrinsicallyinterface-specific,was used to detect the chemical structure of PS surface at the molecular level after various aging times.The results are interpreted as follows.During the aging of the plasma treated PS surfaces,the oxygen containing groupsundergo reorientation processes toward the polymer bulk and/or parallel to the surface,while the CH_2 moiety stands up onthe PS surface.Our results indicate that the surface configuration changes do not require large length scale segmentalmotions or migration of macromolecules.Motions that are responsible for surface configuration changes could be relativelysmall rotational motions.The aging behaviors under different relative humidity conditions were shown to be similar from18% to 91%,whereas the kinetics of surface polarity decays were faster in higher relative humidity.Here,the surfacerearrangement of polystyrene films that were previously treated by oxygen plasma and aged,and was investigated in terms ofcontact angle after the water immersion.The contact angles of the water-immersed samples were found to change andapproach the initial values before the immersion asymptotically.