DEHYDROGENATION AND AROMATIZATION OF METHANE IN THE ABSENCE OF OXYGEN OVER DOPED Mo/HZSM-5 CATALYSTS

研究了在Ｍｏ／ＨＺＳＭ－５催化剂上添加助剂以及不同的反应预处理温度对甲烷无氧脱氢芳构化反应的影响。实验结果表明，由于第二组分的添加，Ｍｏ／ＨＺＳＭ－５催化剂的活性和选择性都得到了较大程度的改善。预处理温度是影响催化剂反应性能的关键因素。Ｍｏ－Ｒｕ／ＨＺＳＭ－５催化剂经过８７３Ｋ空气预处理后，甲烷在９７３Ｋ的转化率约为１０％，催化剂的稳定性也得到较大程度的提高。ＴＰＳＲ实验结果表明，Ｒｕ的加入降低了芳烃生成的温度。ＴＰＯ和ＤＴＡ实验结果表明，在Ｍｏ－Ｒｕ／ＨＺＳＭ－５催化剂上可生成较多的碳物种，结合反应结果，可以认为反应过程中生成的碳物种对甲烷的无氧脱氢芳构化反应是起积极作用的     

Enhanced Stability of Mo-Promoted Zn/HZSM-5 Catalyst for Methanol to Aromatics

A Mo-promoted Zn/HZSM-5 catalyst was prepared by isometric impregnation method (IM). The physicochemical properties of catalysts were characterized by X-ray diffraction, registration of N₂ adsorption-desorption isotherms, transmission electron microscopy, NH₃ temperature-programmed desorption and IR spectroscopic study of pyridine adsorption. The results show that by doping zeolite with Mo species it is possible to tune the microstructures, acidity and crystallinity of the catalyst. Additionally, it was found that the 1%Mo(IM)–5%Zn(IE)/HZSM-5 catalyst had a high catalytic activity and stability for methanol to aromatics (MTA) reaction. The yield of aromatics reached 77.3% at 450°C and TOS = 3 h. When the TOS = 98 h, the yield of total aromatics remains at a 60.4% level. The lifetime of catalysts was influenced by the synergetic effect of Brønsted and Lewis acid sites, so the modification with Mo may bring an opportunity to prolong the lifetime of Zn/HZSM-5 catalyst in the MTA reaction. The metal components are sintered and lost in continuous reaction-regeneration cycles. Accordingly, the activity of deactivated catalyst cannot be completely restored to the initial level.     

Methane to Liquid Hydrocarbons over Tungsten-ZSM-5 and Tungsten Loaded Cu/ZSM-5 Catalysts

Metal containing ZSM-5 can produce higher hydrocarbons in methane oxidation. Many researchers have studied the applicability of HZSM-5 and modify ZSM-5 for methane conversion to liquid hydrocarbons, but their research results still lead to low conversion, low selectivity and low heat resistance. The modified HZSM-5, by loading with tungsten (W), could enhance its heat resistant performance, and the high reaction temperature (800℃) did not lead to a loss of the W component by sublimation. The loading of HZSM-5 with tungsten and copper (Cu) resulted in an increment in the methane conversion as well as CO2 and C5 selectivities. In contrast, CO, C2-3 and H2O selectivities were reduced. The process of converting methane to liquid hydrocarbons (C5 ) was dependent on the metal surface area and the acidity of the zeolite. High methane conversion and C5 selectivity, and low H2O selectivity are obtained over W/3.0Cu/HZSM.     

Non-oxidative dehydro-oligomerization of methane to higher molecular weight hydrocarbons at low temperatures

The non-oxidative dehydro-oligomerization of methane to higher molecular weight hydrocarbons such as aroma tics and C2 hydrocarbons in a low temperature range of 773-973 K with Mo/HZSM-5,Mo-Zr/HZSM-5 and Mo-W/HZSM-5 catalysts is studied.The means for enhancing the activity and stability of the Mo-containing catalysts under the reaction conditions is reported.Quite a stable methane conversion rate of over 10% with a high selectivity to the higher hydrocarbons has been obtained at a temperature of 973 K.Pure methane conversions of about 5.2% and 2.0% have been obtained at 923 and 873 K,respectively.In addition,accompanied by the C2-C3 mixture,tht- methane reaction can be initiated even at a lower temperature and the conversion rate of methane is enhanced by the presence of tne initiator of C2-C3 hydrocarbons.Compared with methane oxidative coupling to ethylene,the novel way for methane transformation is significant and reasonable for its lower reaction temperatures and high selectivity to the desired prod     

Methane dehydroaromatization with periodic CH_4-H_2 switch:A promising process for aromatics and hydrogen

Long-term stability test of Mo/HZSM-5-N catalysts(HZSM-5-N stands for nano-sized HZSM-5) in methane dehydroaromatization(MDA)reaction has been performed with periodic CH4-H2 switch at 1033-1073 K for more than 1000 h.During this test,methane conversion ranges from 13% to 16%,and mean yield to aromatics(i.e.benzene and naphthalene) exceeds 10%.N2-physisorption,XRD,NMR and TPO measurements were performed for the used Mo/HZSM-5 catalysts and coke deposition,and the results revealed that the periodic hydrogenation can effectively suppress coke deposition by removing the inert aromatic-type coke,thus ensuring Mo/HZSM-5 partly maintained its activity even in the presence of large amount of coke deposition.The effect of zeolite particle size on the catalytic activity was also explored,and the results showed that the nano-sized zeolite with low diffusion resistance performed better.It is recognized that the size effect was enhanced by reaction time,and it became more remarkable in a long-term MDA reaction even at a low space velocity.     

Solid state 13C NMR studies of methane dehydroaromatization reaction on Mo/HZSM-5 and W/HZSM-5 catalysts

Methane dehydroaromatization on Mo/HZSM-5 and W/HZSM-5 catalysts was studied by solid state 13C NMR spectroscopy, both variation of the state of transition metal component and products such as ethane, benzene, ethene adsorbed on or in zeolite were observed after high temperature (900-1000 K) reaction.     

Catalytic Oxidation of Methane by Nitrous Oxide on H[Al]ZSM-5 Zeolite, Silicalite, and Amorphous SiO2 Modified by Iron, Silver, and Gadolinium Ions

Methane oxidation by an excess of N₂O on the catalytic sites formed in HZSM-5 zeolite, silicalite, and SiO₂ after modification with iron, silver, and gadolinium cations in different combinations is studied. Introduction of iron and silver ions into H[Al]ZSM-5 zeolite is shown to result in the formation of the sites that are active in methane oxidation, while the systems obtained on the basis of crystalline silicalite or amorphous SiO₂ demonstrate poor or no catalytic activity, respectively. Complete oxidation of methane with 100% conversion is observed on the Fe/HZSM-5 and Ag/HZSM-5 catalysts at temperatures higher than 350 and 450°C, respectively. A decrease in the reaction temperature and in the methane conversion is accompanied by coking of the catalysts and, in the case of Fe/HZSM-5, by the appearance of trace amounts of methanol and formic acid in the gas phase. The temperature dependence of the activity and selectivity for the Ag/HZSM-5 and (Ag + Gd)/HZSM-5 catalysts exhibits a pronounced hysteresis at 330–480°C, and the formation of coke proceeds much faster than in the case of iron-containing samples. Catalytic properties of (Fe + Ag)/HZSM-5 are similar to those of Fe/HZSM-5. The introduction of Gd does not influence significantly the activity and selectivity of the catalysts. ESR and TG–DTA were used to determine the state and distribution of Fe, Ag, and Gd in the samples and to examine the processes of coke formation.     

强酸促进的W/HZSM-5基催化剂上甲烷非氧化脱氢芳构化

甲烷非氧化催化脱氢芳构化制芳烃是近年来甲烷优化利用的新研究方向之一"－'．迄今已报道的催化剂多为以HZSM－5分子筛为载体的过渡金属（如Pd、I't、Re和MO等）氧化物,其中以改进型的MO／HZSM－5基催化剂效果最佳［'－'j．按化学反应计量式6CH。--C6H。＋gH;进行热力学计算,结果表明：在773K温度下,甲烷平衡转化率（KC。。。,衡）仅为卫·8％;在叮3K和】023K时,xCH。平。分别为】1·3％和15·8％;若使Xo。。,Y＆达25％以上,则要求反应温度不低于1123K（在1123K和1173K时,XCH。,y＆分别为27·2％和33·196）·然…     

沸石载体结构对甲烷无氧芳构化性能的影响

考察了担载MoO₃的沸石催化剂上甲烷的无氧芳构化性能,并与沸石结构相关联.结果表明,孔径与苯分子动态直径相当的ZSM-5、ZSM-8、ZSM-11和β沸石等是甲烷无氧芳构化催化剂的良好载体,其中3%MoO₃/HZSM-11具有最高的甲烷芳构化活性和稳定性,973K下的转化率和苯选择性分别为8.0%和90.9%;6%MoO₃/HZSM-8与7%MoO₃/H-β芳构化性能相当.以HMCM-41和HSAPO-34为载体时芳构化活性很低,以HMOR、HX和HY为载体时仅有少量乙烯生成,而以HSAPO-5和HSAPO-11为载体时未检测到烃类生成.     

FT-IR evidence for the participation of protonic sites in the heterolytic cleavage of C?H bonds of methane over HZSM-5 zeolite

It has been observed by FT-IR spectroscopy that both kinds of Brönsted acid protons present in HZSM-5 zeolite may be involved in the adsorption of methane at low temperature (173 K) and exchange with CH₄ or CD₄ at high temperature (>500°C). The sites which can adsorb methane at low temperature are the active sites for methane conversion at high temperature. Over HZSM-5 zeolite, the activation of methane is suggested to occur via a heterolytic cleavage of C–H bond with the assistance of protons.     

Direct conversion of natural gas to higher hydrocarbons: A review

Direct conversion of methane to higher hydrocarbons is an effective process to solve the problem of natural gas utilization. Although remarkable progress has been achieved on the dehydro-aromatization of methane (DAM), low conversion caused by severe thermodynamic limitations, coke formation, and catalysis deactivation remain important drawbacks to the direct conversion process. Molybdenum catalysts supported on HZSM-5 type zeolite support are among the most promising catalysts. This review focuses on the aspects of direct methane conversion, in terms of catalysts containing metal and support, reaction conditions, and conversion in different types of reactors. The reaction mechanism for this catalytic process is also discussed.     

Pt改性分子筛催化剂上丙烷与苯的烷基化反应

研究了不同分子筛负载的Pt催化剂上丙烷与苯的烷基化反应.结果表明,Pt/HZSM-5具有较好的催化性能.在0~0.3%范围内提高Pt负载量可以提高催化剂的催化活性和生成C9以及C10 芳烃的选择性,降低非芳烃产物的选择性.较低的反应温度、较高的苯/丙烷摩尔比和较高的空速有利于烷基芳烃的生成.     

Dual-Bed Catalytic System for Direct Conversion of Methane to Liquid Hydrocarbons

A dual-bed catalytic system is proposed for the direct conversion of methane to liquid hydrocarbons. In this system, methane is converted in the first stage to oxidative coupling of methane (OCM) products by selective catalytic oxidation with oxygen over La-supported MgO catalyst. The second bed, comprising of the HZSM-5 zeolite catalyst, is used for the oligomerization of OCM light hydrocarbon products to liquid hydrocarbons. The effects of temperature (650-800℃), methane to oxygen ratio (4 10), and SiO2/Al2O3 ratio of the HZSM-5 zeolite catalyst on the process are studied. At higher reaction temperatures, there is considerable dealumination of HZSM-5, and thus its catalytic performance is reduced. The acidity of HZSM-5 in the second bed is responsible for the oligomerization reaction that leads to the formation of liquid hydrocarbons. The activities of the oligomerization sites were unequivocally affected by the SiO2/Al2O3 ratio. The relation between the acidity and the activity of HZSM-5 is studied by means of TPD-NH:j techniques. The rise in oxygen concentration is not beneficial for the C5 selectivity, where the combustion reaction of intermediate hydrocarbon products that leads to the formation of carbon oxide (CO CO2) products is more dominant than the oligomerization reaction. The dual-bed catalytie system is highly potential for directly converting methane to liquid fuels.     

程序升温技术研究Mo/HZSM-5催化剂上甲烷无氧芳构化反应积炭的化学特性

对经过程序升温表面甲烷无氧芳构化反应(TPSR)后的Mo/HZSM-5催化剂上的积炭进行了程序升温加氢反应(TPH)和程序升温CO₂反应(TPCO₂),并对相应催化剂上的积炭进行了程序升温氧化反应(TPO)和热重(TG)实验.TPH实验及TPCO₂实验表明,H₂主要对高温烧炭峰发生作用.CO₂则可同时对这两种烧炭峰产生影响,对低温峰积炭的影响尤其明显.对不同Mo含量的催化剂进行上述实验的结果表明,Mo担载量的变化及不同的实验过程都会影响催化剂上两种温峰的积炭在总积炭量中所占的比例.由TG实验数据计算出的动力学结果说明,无论是TPH还是TPCO₂实验都可以降低烧炭过程的一级反应起始温度,并减少其活化能.此外,催化剂中Mo担载量的变化也会对开始温度和烧炭活化能产生明显影响.     

27Al和29Si MAS-NMR对Mo/HZSM-5催化剂的研究

使用＾２９Ａｌ固体离分辨核磁技术对甲烷无氧芳构化催化剂Ｍｏ／ＨＺＳＭ－５分子筛进行了研究，发现ＨＺＳＭ－５分子筛本体中仅含有少量非骨架Ａｌ，Ｍｏ物种与分子筛骨架Ａｌ的相互作用随Ｍｏ担载量以及焙烧的温度的升高而增加，在高温焙烧下，Ｍｏ物种会使分子筛骨架严重脱铝，并且生成Ａｌ２（ＭｏＯ４）３新相，最终导致分子筛骨架塌陷，催化性能下降。     

用于乙烯芳构化反应的Zn/HZSM-5催化剂失活机制研究

采用浸渍法制备了Zn负载量（质量分数）分别为1%、2%、3%的Zn/HZSM-5分子筛催化剂,通过XRD、N₂吸附-脱附、NH₃-TPD、Py-FTIR、XPS、TG-DTA等技术,系统考察Zn/HZSM-5分子筛在乙烯芳构化反应的失活机制。结果表明,积炭是催化剂失活的主要原因,HZSM-5中Zn的添加在较大程度上抑制了催化剂的积炭行为;低Zn含量时催化剂失活缓慢,但Zn含量较高时,由于催化剂比表面积和孔体积极剧下降,催化剂失活加剧。反应过程中,分子筛上Zn物种存在迁移和流失行为,迁移行为体现为催化剂表面Zn的富集和相对比例的变化;Zn流失速率在不同反应阶段保持恒定,但受到Zn含量的影响,Zn含量越高、流失速率越大。外表面ZnO是分子筛催化剂Zn流失的主要物种,且随Zn负载量升高变化趋势愈加明显,其含量与积炭速率存在一定关联。     

Non-Oxidative Aromatization of CH4-C_3H_8 over La-Promoted Zn/HZSM-5 Catalysts

The non-oxidative aromatization of mixed CH4 with C3H8 over La-promoted Zn/HZSM-5 catalysts was studied in a fixed-bed reactor at 823 K with space velocity 600 h-1 and CH4/C3H8 (mol ratio)=5:1. The propane conversion and the aromatic selectivities were up to 99% and 60% over the catalyst respectively, while methane conversion had an induction period with the highest conversion of 30%. The structure and surface acidity of the catalysts were characterized by XRD, NH3-TPD and TG-DTA. The influences of reaction and regenerative conditions on the activity and selectivity were also investigated.     

甲烷在Mo/HZSM-5催化剂上的脱氢聚合反应

对不同Mo含量的Mo／HZSM－5催化剂的结构进行了表征，并对这些催化剂的甲烷非氧气氛下的转化反应进行了考察．催化剂的BET比表面积及酸性随Mo含量的增加而降低，当Mo含量大于5％时，Mo对ZSM－5分子筛的晶型有影响，并出现MoO3物相．甲烷在700℃时可高选择性地生成苯和乙烯，最佳Mo含量大约为2％．纯的MoO3或HZSM－5上该反应几乎不进行，因此，可能是分散的钼氧离子和分子筛的酸中心是甲烷转化的活性中心，只有二者的协同作用才能促进甲烷的转化．反应后催化剂中的钼物种被还原了．催化剂上的积炭可能是催化剂失活的主要原因之一，烧炭后催化剂活性基本恢复．     

甲烷在Mo/HZSM-5催化剂上的脱氢聚合反应

对不同Mo含量的Mo／HZSM－5催化剂的结构进行了表征，并对这些催化剂的甲烷非氧气氛下的转化反应进行了考察．催化剂的BET比表面积及酸性随Mo含量的增加而降低，当Mo含量大于5％时，Mo对ZSM－5分子筛的晶型有影响，并出现MoO3物相．甲烷在700℃时可高选择性地生成苯和乙烯，最佳Mo含量大约为2％．纯的MoO3或HZSM－5上该反应几乎不进行，因此，可能是分散的钼氧离子和分子筛的酸中心是甲烷转化的活性中心，只有二者的协同作用才能促进甲烷的转化．反应后催化剂中的钼物种被还原了．催化剂上的积炭可能是催化剂失活的主要原因之一，烧炭后催化剂活性基本恢复．     

Cu-Pd/MCM-22催化剂上二甲醚低温水解反应

 考察了分子筛的类型、硅铝比及Cu和Pd改性对分子筛催化剂上二甲醚低温水解活性的影响. 结果表明,酸性的MCM-22和HZSM-5分子筛催化剂具有较高的二甲醚水解活性,且其活性随着分子筛硅铝比的增加而降低. 这表明分子筛的类型及酸性对催化剂性能有重要影响,具有超笼结构的MCM-22分子筛上B酸中心的良好可接近性,使得该分子筛催化剂的水解活性较相同硅铝比的HZSM-5分子筛高. 与改性前相比, Cu和Pd改性后的MCM-22催化剂显示出更高的二甲醚水解活性.