Various Current Responses of Single Silver Nanoparticle Collisions on a Gold Ultramicroelectrode Depending on the Collision Conditions

Collisions of silver nanoparticles (NPs) with a more electrocatalytic gold or platinum ultramicroelectrode (UME) surface have been observed by using an electrochemical method. Depending on the applied potential to the UME, the current response to the collision of Ag NPs on the UME resulted in various shape changes. A staircase decrease, a blip decrease, and a blip increase of the hydrazine oxidation current were obtained at an applied potential of 0.33, 0.80, and 1.3 V, respectively. Different collision behaviors of Ag NPs on the UME surface were suggested for each shape of current response. Ag NP attachment, which hindered the diffusion flux to the UME, caused a staircase decrease of the electrocatalytic current. Instantaneous blocking of the hydrazine oxidation by Ag NP collision and, following recovery of the current by means of oxidation of Ag NP, caused a blip decrease of the electrocatalytic current. The formation of a higher oxidation state of Ag on the Ag NP and its electrocatalytic hydrazine oxidation resulted in a blip increase of the electrocatalytic current. The analysis of the current response of a single NP collision experiment can be a useful tool to understand the various behaviors of NPs on the electrode surface.     

DNA analysis by application of Pt nanoparticle electrochemical amplification with single label response

This study demonstrates a highly sensitive sensing scheme for the detection of low concentrations of DNA, in principle down to the single biomolecule level. The previously developed technique of electrochemical current amplification for detection of single nanoparticle (NP) collisions at an ultramicroelectrode (UME) has been employed to determine DNA. The Pt NP/Au UME/hydrazine oxidation reaction was employed, and individual NP collision events were monitored. The Pt NP was modified with a 20-base oligonucleotide with a C6 spacer thiol (detection probe), and the Au UME was modified with a 16-base oligonucleotide with a C6 spacer thiol (capture probe). The presence of a target oligonucleotide (31 base) that hybridized with both capture and detection probes brought a Pt NP on the electrode surface, where the resulting electrochemical oxidation of hydrazine resulted in a current response.     

Observation of Single Pt Nanoparticle Collisions: Enhanced Electrocatalytic Activity on a Pd Ultramicroelectrode

Single Pt nanoparticle (NP) collisions on an electrode surface were detected by using an electrocatalytic amplification method with a Pd ultramicroelectrode (UME). Pd is not a preferred material for UMEs for the detection of single Pt NP collisions, because Pd shows similar electrocatalytic activity compared with Pt for hydrazine oxidation, thus resulting in a high background current level. However, a Pt NP colliding on the Pd UME shows greatly enhanced activity compared with a Pt NP on an inert UME, such as a Au UME, which is usually used for the detection of single Pt NP collisions. The use of an electroactive UME material instead of an inert one facilitated the study of single‐NP activity on the various solid supports, which is important in many NP applications.     

Combined Blip and Staircase Response of Ascorbic Acid‐Stabilized Copper Single Nanoparticle Collision by Electrocatalytic Glucose Oxidation

The current response of the collision of ascorbic acid‐stabilized copper (Cu) single nanoparticles (NPs) on a gold (Au) ultramicroelectrode (UME) surface was observed by using an electrocatalytic amplification method. Here, the glucose oxidation electrocatalyzed by oxidized Cu NPs was used as the indicating reaction. In this system, the NP collision signals were obtained simultaneously by both direct particle electrolysis and electrocatalytic amplification. For example, when the applied potential was high enough for Cu NP oxidation, a blip response combined with a staircase response was observed as a current signal. The blip part in the single Cu NP collision signal indicates the self‐oxidation of a Cu NP, and the staircase part indicates the steady‐state electrocatalytic reaction by oxidized Cu NP.     

A Snapshot of the Properties of Single Nanoparticles at the Moment of a Collision

Direct electrochemical characterization of freely moving nanoparticles (NPs) at the individual particle level is challenging. A method is presented that can achieve this goal based on the collision between a NP and an ultramicroelectrode (UME). By applying a sinusoidal potential to the UME and monitoring the current response in the frequency domain, a sudden change in the phase angle indicates the arrival of a NP at the UME. The response induced by the collision can be isolated and used to explore the properties of the NP. This method, analogous to a high‐speed camera, can obtain a snapshot of the properties of the single NP at the moment of a collision. The proposed method was employed to investigate the properties of both the hard catalytic Pt NP and soft electroactive emulsion droplets, and many new insights were revealed thereafter. The method also has the potential to be applied in many other fields, where the interested signals appear as discrete events.     

Study of Electron Transfer Reactions Between a Water／1,2-Dichloro-ethane Interface by Scanning Electrochemical Microscopy

Electron transfer (ET) from ascorbic acid (AA) in aqueous to ferrocene (Fc) in 1,2-dichloroethane (DCE) was probed by the scanning electrochemical microscopy (SECM). Therate constants were extracted from the dependence of the steady-state current at ultramicro- electrode (UME, tip) on the distance between the tip and the phase boundary by comparison to theoretical working cures.     

Microelectrodes modification through the reduction of aryl diazonium and their use in scanning electrochemical microscopy (SECM)

This work is devoted to the study of the electrochemical grafting of nitrophenyl groups onto platinum ultramicroelectrode (UME). The grafting was made using the electrochemical reduction of nitrophenyldiazonium. Our results demonstrate the possibility to reduce the diazonium onto Pt UME. As consequence the electrochemical reduction leads to the attachment of nitrophenyl groups onto the UME surface. Following that, the modified UME was characterized using electrochemical techniques. In addition, the electrochemical response of the modified UME in the presence of reversible redox couple, ferrocene, has been studied. The main remark is that the steady state current observed at the UME is not affected by the presence of the nitrophenyl layers. Finally, from this last point we demonstrate the possibility to achieve scanning electrochemical microscopy (SECM) using modified platinum UME.     

Impacts of Forced Convection Generated via High Precision Stirring on Scanning Electrochemical Microscopy Experiments in Feedback Mode

In this study, the effects of forced convection on scanning electrochemical microscopy (SECM) experiments in feedback mode using ferrocenemethanol as redox mediator are presented. Forced convection, which enhances the mass transfer inside the system, was generated via an electrical high precision stirrer integrated into the SECM setup. A thin‐film interdigitated array electrode serving as model substrate was investigated with probe scan curves in z‐direction and SECM imaging in constant height mode utilizing ultramicroelectrodes (UME) with diameters (d_probe) of 25 μm and 12.5 μm. It was found that forced convection increased the overall current during SECM imaging without distorting distinctive features of the imaged structure when working with a 25 μm UME at substrate‐to‐tip distances of 14 μm and 11 μm. Furthermore, the electrochemical contrast was improved under hydrodynamic conditions for a substrate‐to‐tip distance of 11 μm and scan rates of 5 μm s^?1, 10 μm s^?1, 20 μm s^?1 and 40 μm s^?1. When further decreasing the gap between the UME and the substrate to 9 μm almost no effects of the forced convection were observed. Consequently, for a 25 μm UME, forced convection led to higher currents and improved performance during SECM experiments in feedback mode at substrate‐to‐tip distances of 14 μm and 11 μm, whereas no effects were observed for a 12.5 μm UME at a distance of 8 μm.     

单个Nafion@Ru和Au-Nafion@Ru纳米粒子的电化学和电化学发光碰撞行为研究

通过静电作用在Nafion和Au-Nafion纳米粒子(NPs)上负载钌联吡啶(Ru(bpy)32+)分别制得Nafion@Ru和Au-Nafion@Ru NPs.分析并比较了Au-Nafion@Ru和Nafion@Ru NPs在金超微电极(Au UME)上随机碰撞产生电流响应峰的平均峰大小、峰电量和单峰持续时间,建立...     

Imaging the stomatal physiology of somatic embryo-derived peanut leaves by scanning electrochemical microscopy

The stomatal physiology, chlorophyll distribution and photosynthetic activity of somatic embryo (SE)- and seedling-derived peanut plants grown in vitro (test tube-grown) and extra vitrum (soil-grown) are investigated using scanning electrochemical microscopy (SECM). This SECM imaging is performed in two different feedback modes, corresponding to oxygen evolution and chlorophyll distribution. More specifically, the oxygen evolution profiles of the in vitro leaves indicate important differences in leaf anatomy between the SE- and seedling-derived leaves. On the other hand, the chlorophyll distribution images show individual stomata of size ca. 27 ± 5μm. Further studies on senescing (aged) leaves reveal interesting voltammograms that vary widely over the stomatal complexes and the surrounding tissues, probably due to the release of electroactive metabolites during chlorophyll breakdown when the leaves turn yellow. Thus, the present investigation could open up new opportunities for characterizing botanical systems using electroanalytical techniques. In addition, it could provide further insights into various areas of current relevance, including signal transduction, cell fate/differentiation and developmental biology. Schematic representation of SECM imaging used in this investigation. The SECM probe is a Pt UME disk (25 μm diameter) embedded in an insulating glass sheath so that the ratio of the diameter of the death to that of the electrode surface (RG) is 7. RE denotes the reference electrode Ag/AgCl, sat. KCl and CE refers to the counter electrode, a Pt wire. Oxygen evolving from the leaf surface during photosynthesis diffuses into the electrolyte (0.1 M KCl) and gets reduced at the Pt UME, biased to a potential of −0.5 V, at a diffusion-limited rate to produce a change in the tip-current     

Surface interrogation mode of scanning electrochemical microscopy for oxidation study of adsorbed CO generated from serine on platinum

We report a new method for detection and oxidation of adsorbed carbon monoxide(CO_（ads）) generated from serine on a polycrystalline platinum ultramicroelectrode（UME） by bromine（Br₂） using in situ surface interrogation（SI） mode of scanning electrochemical microscopy（SECM）.In the SI mode,tip and substrate are both Pt UMEs,and CO_（ads） on Pt substrate,generated from serine,can be oxidized by the tip-generated Br₂ giving a positive response.Dosing CO_（ads） from serine instead of purging CO gas expands the newly introduced reaction of Br₂ with CO_（ads） and further enhances the hope to get rid of CO_（ads） on Pt for fuel cells.     

On the diffusion of ferrocenemethanol in room-temperature ionic liquids: an electrochemical study

The electrochemical behaviour of ferrocenemethanol (FcMeOH) has been studied in a range of room-temperature ionic liquids (RTILs) using cyclic voltammetry, chronoamperomery and scanning electrochemical microscopy (SECM). The diffusion coefficient of FcMeOH, measured using chronoamperometry, decreased with increasing RTIL viscosity. Analysis of the mass transport properties of the RTILs revealed that the Stokes-Einstein equation did not apply to our data. The "correlation length" was estimated from diffusion coefficient data and corresponded well to the average size of holes (voids) in the liquid, suggesting that a model in which the diffusing species jumps between holes in the liquid is appropriate in these liquids. Cyclic voltammetry at ultramicroelectrodes demonstrated that the ability to record steady-state voltammograms during ferrocenemethanol oxidation depended on the voltammetric scan rate, the electrode dimensions and the RTIL viscosity. Similarly, the ability to record steady-state SECM feedback approach curves depended on the RTIL viscosity, the SECM tip radius and the tip approach speed. Using 1.3 μm Pt SECM tips, steady-state SECM feedback approach curves were obtained in RTILs, provided that the tip approach speed was low enough to maintain steady-state diffusion at the SECM tip. In the case where tip-induced convection contributed significantly to the SECM tip current, this effect could be accounted for theoretically using mass transport equations that include diffusive and convective terms. Finally, the rate of heterogeneous electron transfer across the electrode/RTIL interface during ferrocenemethanol oxidation was estimated using SECM, and k(0) was at least 0.1 cm s(-1) in one of the least viscous RTILs studied.     

结合光学成像技术研究单颗粒碰撞电化学

近年来,单颗粒碰撞技术在纳米电化学领域受到广泛关注. 该技术通常控制超微电极处于某一电位,检测单个纳米颗粒随机碰撞到电极表面后产生的瞬时电流. 通过分析电流信号,可以研究单个纳米颗粒的性质. 尽管该技术可以检测单个纳米颗粒的电化学或电催化电流,但是传统的单颗粒碰撞技术缺乏空间分辨率,难以识别和表征特定的纳米颗粒. 因此,结合光学成像技术研究单颗粒碰撞电化学来补充电化学技术缺失的空间信息已成为一种趋势. 本文首先简要综述了单颗粒碰撞技术的三种检测原理,主要介绍了近年来单颗粒碰撞技术与荧光显微镜、表面等离激元共振显微镜、全息显微镜和电致化学发光相结合的研究进展,最后展望了单颗粒碰撞技术未来的发展趋势.     

Mathematical Modelling of the Influence of Ultra‐micro Electrode Geometry on Approach Curves Registered by Scanning Electrochemical Microscopy

Scanning electrochemical microscopy (SECM) is an emerging electroanalytical sensing technique, used to investigate the electrochemical properties of the sample by ultra‐micro‐electrode(UME) scanning probe. UME signal usually is the current, which depends not only on the properties of the evaluated system but also on UME characteristics such as geometry. Variations of UME geometry can decrease accuracy of the measurement, and then correct analysis of the SECM data becomes almost impossible. In the present work, we studied the precision of measurements with three different the most frequent types of defected UME's ((i) recessed‐UME, (ii) outwarded‐UME, (iii) cone‐UME). Measurement results were compared with that obtained with not defected standard‐plane‐UME. Computational experiment was performed with SECM model using diffusion equations with non‐rectangular border conditions to calculate estimated currents for these three types of defected UMEs and to compare them with that for standard‐plane‐UME. In order to test the correctness of the model, computations for recessed‐UME model were compared with data of real‐recessed‐UME experiment.     

Observation of single metal nanoparticle collisions by open circuit (mixed) potential changes at an ultramicroelectrode

Single nanoparticle (NP) collisions were successfully observed by a potentiometric measurement. The open circuit potential (OCP) of a measuring Au ultramicroelectrode (UME) changes when Pt NPs collide with the UME in a hydrazine solution. The OCP change is related to the redox processes, the concentration of particles, particle size, and electrode size. Compared with the amperometric technique, this approach has several advantages: higher sensitivity, simpler apparatus, fewer problems with NP decomposition, and contamination.     

Scanning electrochemical microscopy (SECM) studies of catalytic EC' processes: theory and experiment for feedback, generation/collection and imaging measurements

This paper describes the use of scanning electrochemical microscopy (SECM) in the tip generation/substrate collection (TG/SC), or feedback, mode and substrate generation/tip collection (SG/TC) mode to measure homogeneous kinetics in the catalytic EC' process. Theoretical analyses of both configurations have been developed numerically to allow the optimal conditions for sensitive kinetic measurements to be determined. This is shown to involve collection efficiency measurements as a function of tip-substrate electrode distance in the case of TG/SC measurements and tip (collector current) images in a plane normal to the substrate electrode for the SG/TC mode. An important consideration for the SECM configuration (particularly for TG/SC and feedback measurements) is that the electroinactive co-reactant may be depleted more significantly than with other electrode geometries, because of cycling of the redox couple in the tip/substrate electrode gap, while the co-reactant can only enter this gap by hindered diffusion. The approaches described are examined through studies of the oxidation of amidopyrine by electrogenerated Fe(CN) in 0.5 mol dm(-3) aqueous KOH solution. A second-order rate constant of 390 ± 80 dm(3) mol(-1) s(-1) is obtained from TG/SC measurements, consistent with SG/TC quantitative imaging measurements. The consistency of the kinetic measurements confirms the validity of the approaches described. The kinetic constant is lower than expected based on previous ultramicroelectrode (UME) studies, and this is attributed to the fact that background currents for the direct heterogeneous oxidation of amidopyrine are more significant with conventional UME measurements, which will tend to enhance the current measured and may therefore lead to an overestimation of kinetic constants. The TG/SC approach, on the other hand, provides a means of making dual-electrode collection efficiency measurements with diffusional feedback of the redox couple, leading to superior voltammetric responses and enabling more accurate kinetic determination.     

Fabrication of Prussian Blue modified ultramicroelectrode for GOD imaging using scanning electrochemical microscopy

A Prussian Blue (PB) film modified disk ultramicroelectrode (UME) was fabricated by electrochemical deposition technique on a Pt-disk UME. The electrocatalytical reductions of hydrogen peroxide derived from glucose oxidase (GOD) on this modified UME were investigated. The enzymatic biochemical reactivity was imaged by scanning electrochemical microscopy (SECM) utilizing the PB film modified UME. It is evident that sensitivity and spatial resolution for hydrogen peroxide measurement were improved obviously. SECM images obtained clearly revealed the concentration profile of the reaction products around the enzymes. The PB film modified microelectrode is in the nature of simple preparation, high catalytic activity on hydrogen peroxide and substrate selectivity for SECM etc.     

Electrochemical detection of reduced graphene oxide nanoparticles in aqueous solution

We have demonstrated electrochemical detection of reduced graphene oxide (rGO) nanoparticles on an ultramicroelectrode (UME) in aqueous solution using rGO collision events. The collision phenomena are detected by monitoring a current–time transient. To attract the rGO to the UME surface, a positive electric field was developed near the UME using a redox reaction. As model systems, ferrocenemethanol and ferrocyanide oxidation reactions were adopted. Amperometric current measurements showed a staircase current response after attachment of rGO on the UME surface. The magnitude of the staircase current is given by the stepwise increase in current, which can provide insight into the size distribution of the rGO colliding with the UME. In the presence of higher concentrations of rGO, multiple collision events happened sequentially on the UME. In this case, an increasing current trend, rather than a single staircase current, was observed. The overall current increment for a given time is a measure of the concentration of rGO in solution. By using this method, charged conductive materials in an aqueous solution can be sensitively detected and/or accumulated.     

Scanning electrochemical microscopy #54. Application to the study of heterogeneous catalytic reactions-hydrogen peroxide decomposition

A scanning electrochemical microscopy (SECM) approach for the analysis of heterogeneous catalytic reactions at solid-liquid interfaces is described and applied. In this scheme, reactant, generated at a tip, undergoes a reaction (e.g., disproportionation) at the substrate. The theoretical background for this study, performed by digital simulations using a finite difference method, considers a chemical reaction at the substrate with general stoichiometry. In this case, the fraction of regenerated mediator (nu(S)) may differ with respect to a substrate reaction that is the reverse of the tip reaction, resulting in an asymmetric mediator loop. Simulated tip current transients and approach curves at different values of the kinetic rate constant for reactions where nu(S) < 1 were used to analyze this new SECM situation. This approach was used to study the catalytic decomposition of hydrogen peroxide (HO2- --> 1/2O2 + OH-), where nu(S) = 0.5, on supported catalysts. A gold-mercury amalgam tip was used to quantitatively reduce dissolved O2 (mediator) to HO2-, which was decomposed back to oxygen at the catalyst substrate. Rate constants for the decomposition reaction on immobilized catalase and Pt particles were measured at different pH values by the correlation of experimental approach curves with the theoretical dependencies.     

Stochastic electrochemistry with electrocatalytic nanoparticles at inert ultramicroelectrodes--theory and experiments

Collisions of several kinds of metal or metal oxide single nanoparticles (NPs) with a less catalytic electrode surface have been observed through amplification of the current by electrocatalysis. Two general types of current response, a current staircase or a current blip (or spike) are seen with particle collisions. The current responses were caused by random individual events as a function of time rather than the usual continuous current caused by an ensemble of a large number of events. The treatment of stochastic electrochemistry like single NP collisions is different from the usual model for ensemble-based electrochemical behaviour. Models for the observed responses are discussed, including simulations, and the frequency of the steps or blips investigated for several systems experimentally.