An approach for decontamination of beta-lactam antibiotic residues or contaminants in the pharmaceutical manufacturing environment

An effective procedure for decontamination of beta-lactam antibiotic residues or contaminants in the pharmaceutical manufacturing environment was investigated. Decontamination with solutions of hydrochloric acid, sodium hydroxide, hydrogen peroxide and hydroxylamine as agents for degradation was assessed. According to the results, the beta-lactam antibiotics were significantly degraded with sodium hydroxide and hydroxylamine. From the structural analysis of the degradation products of a cephem antibiotic, cefpodoxime proxetil, it was found that hydroxylamine degraded the beta-lactam structure under mild conditions, while sodium hydroxide did not. Therefore, hydroxylamine was considered an appropriate decontamination agent for beta-lactam antibiotics.     

Simultaneous determination of different antibiotic residues in bovine and in porcine kidneys by solid-phase fluorescence immunoassay

Parallux, a solid-phase fluorescence immunoassay (SPFIA) developed for antibiotic residue detection in milk, was used for analysis of bovine and porcine kidney tissue. Four tetracyclines, 2 broad-spectrum cephalosporins, 3 beta-lactam antibiotics, and cephapirin were detected in one run after minimal sample preparation. This commercially available test system is designed as cartridges, each with a combination of 1-4 tests. One cartridge can be used to detect 4 analytes in the same sample, or 1 or 2 analytes in different samples. The cartridge with the combination tetracyclines-ceftiofur-penicillin-cephapirin was selected because tetracyclines, beta-lactam antibiotics as well as cephalosporins, are registered for oral or parenteral use in bovines and pigs in Europe. The test is qualitative and is recommended only for screening. Tetracycline, oxytetracycline, chlortetracycline, and doxycycline were easily detected at 300 ppb with the tetracyclines channel; ceftiofur at 1000 ppb and cefquinome at 200 ppb with the ceftiofur channel; penicillin G, ampicillin, and amoxicillin at 50 ppb with the penicillin channel; and cephapirin at 100 ppb with the cephapirin channel. These levels are equal to or lower than the corresponding maximal residue limits in kidney tissue. Cephalexin was not detected. The SPFIA test can be used as an alternative to classical inhibition tests and for post-screening inhibitor- positive kidneys, because it detects 3 specific groups of antibiotics, which enables selection of specific confirmatory methods for identification and quantification.     

Determination of beta-lactam antibiotics in water by fluorescence quenching of mercurochrome, and application for simple investigation of potency

The fluorescence quenching reaction between fluorescein mercury or halogeno-fluorescein mercury compounds (fl. Hg, 2,7- or 2,4-dichloro-fl.Hg, 3',4',5',6'-tetrachloro-fl.Hg, mercurochrome) and beta-lactam antibiotics (ampicillin (AB-PC) and cephalexin (CEX] was investigated, and mercurochrome was selected for the detection of beta-lactam antibiotics; the detection limit was about 0.8 micrograms/ml. A fluorimetric assay of beta-lactam antibiotics was established by measuring the fluorescence of mercurochrome and mercurochrome-beta-lactam antibiotics solutions in weakly basic media to determine the degree of fluorescence quenching. The maximum emission wavelength of mercurochrome solution was at 544 nm with excitation at 470 nm. The calibration graphs were linear over the ranges of about 0-6 micrograms/ml beta-lactam antibiotics penicillins (AB-PC, penicillin G, sulbenicillin, amoxicillin, cyclacillin, oxacillin, hetacillin and piperacillin) and cepham antibiotics (CEX, cefazolin, cephaloglycin, cephaloridine and cefpyramide), and the relative standard deviation was 2.7% for 1.4 micrograms/ml of AB-PC (n = 5). This fluorescence quenching reaction between mercurochrome and beta-lactam antibiotics was applied in a survey of decomposition and remaining potency of beta-lactam antibiotics.     

Estimation of the molecular volumes of the reaction products between beta-lactam antibiotics and aminoglycoside antibiotics, and those of the degradation products of beta-lactam antibiotics by isotachophoresis

The correlative equations between the molecular volume and the qualitative indication (hR) for beta-lactam antibiotics, the reaction products between beta-lactam antibiotics and kanamycin, and the degradation products of beta-lactam antibiotics were hR = 0.32 + 0.080 VA2/3//Z/(N = 15, r = 0.972 for penicillins) and hR = 0.04 + 0.072 VA2/3//Z/(N = 12, r = 0.987 for cephems). Where VA is van der Waals volume (A3/molecule), hR is the relative step height in the isotachopherogram, and Z is the electric change, respectively. According to these equations, the molecular volumes of the reaction products between beta-lactam antibiotics and the other aminoglycoside antibiotics, and those of the degradation products of beta-lactam antibiotics can be estimated from the value of hR. Also according to the step height in the isotachopherogram, the reaction products or the degradation products may be estimated directly when the electric charge is known. It was confirmed that a molecule of aminoglycoside antibiotics reacted with a molecule of beta-lactam antibiotics. Therefore, the inactivation of aminoglycoside antibiotics is much greater than for beta-lactam antibiotics when the clinical doses of these antibiotic combinations are used.     

Detection of antibiotics in muscle tissue with microbiological inhibition tests: effects of the matrix.

The effects of the tissue matrix on detection limits of antibiotics with microbiological inhibition tests, intended for muscle tissue, were measured. Pieces of frozen meat were laid directly on top of paper disks impregnated with aqueous antibiotic solutions. Inhibition zones were compared with those obtained by the same standard solution without tissue. Only tetracyclines were detected as efficiently with as without muscle tissue. Inhibition zones of the beta-lactam antibiotics ampicillin and penicillin G, and the fluoroquinolone antibiotics enrofloxacin and ciprofloxacin were smaller when muscle tissue was added to low levels of standard solution. At higher levels the differences were not substantial. Inhibition zones of tylosin were smaller and irregular or had disappeared completely, while ceftiofur, sulfadimidine, erythromycin, lincomycin, and streptomycin were not detected in spiked muscle tissue at concentrations fivefold higher than the detection limits without tissue. These results indicate that ceftiofur, sulfonamides, streptomycin and some macrolide antibiotics cannot be detected in intact meat with the plates and bacterial strains prescribed in the European Four Plate Test, a test which was initially intended as a multi-residue method for muscle tissue. Two plates of this system are not suitable for screening purposes; a third one detects tetracyclines and beta-lactam antibiotics in spiked tissue; the fourth one is sensitive for beta-lactam antibiotics and for some but not all macrolides. Samples spiked with the fluoroquinolones enrofloxacin and ciprofloxacin can be detected with an additional plate, not included in the Four Plate Test.     

Trace determination of beta-lactam antibiotics in surface water and urban wastewater using liquid chromatography combined with electrospray tandem mass spectrometry

A sensitive and reliable method using liquid chromatography-electrospray tandem mass spectrometry has been developed and validated for the trace determination of beta-lactam antibiotics in natural and wastewater matrices. Water samples were enriched by solid-phase extraction. The analytes included amoxicillin (AMOX), ampicillin (AMP), oxacillin (OXA), cloxacillin (CLOX) and cephapirin (CEP). Average recoveries of beta-lactams (BLs) in fortified samples were generally above 75% (except amoxicillin) with the standard deviations lower than 10% in water matrices. Amoxicillin was not quantified due to poor recovery (less than 40%) in the investigated water matrices. Matrix effects were found to be minimal when measuring these compounds in water matrices. The accuracy, within- and between-run precision of the assay fell within acceptable ranges of 15% absolute. The method detection limit (MDL) was estimated to range between 8 and 10 ng/L in surface water, 13 and 18 ng/L in the influent and 8 and 15 ng/L in the effluent from a wastewater treatment plant. A large number of actual water samples were analyzed using this method in order to evaluate the occurrence of the beta-lactams in a river and a wastewater treatment plant in northern Colorado. Most of the samples were negative for all analytes. These compounds were found at 15-17 ng/L in the three influent samples and at 9-11 ng/L in three surface water samples out of a total of 200 samples. This indicates that contamination by beta-lactam antibiotics is of minor importance to the small mixed-watershed.     

Stability of frozen stock solutions of beta-lactam antibiotics, cephalosporins, tetracyclines and quinolones used in antibiotic residue screening and antibiotic susceptibility testing

The stability of frozen stock solutions of antibiotics belonging to three different families was evaluated using an agar diffusion test, with Bacillus subtilis as a test strain. Diameters of inhibition zones were measured at monthly intervals during 6 months, and the decline in active substance was calculated. Penicillin and amoxicillin lost nearly half of their potency, the cephalosporins ceftiofur and cefapirin one quarter, but ampicillin was more stable. The quinolones flumequine, enrofloxacin and marbofloxacin were relatively stable; the loss of activity was less than 10% after 6 months of preservation at -20 degrees C. This was also the case for doxycycline and chlortetracycline, while oxytetracycline and tetracycline lost about 25% of their potency. When used in microbiology, i.e. for residue testing or for determination of minimum inhibitory concentrations, a diminution of activity less than 25% will not be noticed. For these applications, the four tetracyclines and three quinolones tested can be kept for 6 months at -20 degrees C, while the beta-lactam antibiotics should be discarded after 3 months. Standard stock solutions of beta-lactam antibiotics and cephalosporins should preferably be used the same day when they are intended for quantitative residue analysis.     

Experiences with an identification and quantification program for inhibitor-positive milk samples

Beta-lactam antibiotics (penicillins, cephalosporins) are still the most commonly used antibiotics for dairy cows in Germany. In routine milk testing, according to the German milk quality regulation, a positive result obtained for bulk tank milk by microbiological inhibitor tests needs no further confirmation, but results in reduced milk payment of 0.05 euros kg(-1) for one month. In some cases, however, further identification of the causative agent can be of interest, either if antimicrobial drugs have not knowingly been used recently, or if improper use of such drugs is denied. As a service for milk producers, our laboratory offers further analyses of violative milk samples, aiming at the identification and quantification of the inhibitor(s). In this program, a panel of microbiological inhibitor tests, receptor tests, and enzyme immunoassays (EIA) is used in a step-by-step analysis, which primarily focusses on beta-lactams, but also includes other compounds such as sulfonamides or tetracyclines, respectively. Here we report results for violative milk samples (n=63) analysed between 2003 and 2005. In most cases (95%), beta-lactam antibiotics could be identified, although not always at levels exceeding the respective MRL values. Penicillin G (mostly together with benzylpenicilloyl metabolites) could be identified in 74.6% of all samples. Other compounds identified were, in decreasing order, ceftiofur (11%), ampicillin/amoxicillin (6.3%), isoxazolyl penicillins (3.2%), and sulfonamides (1.6%). The results indicate that penicillin G is still the predominant antibiotic responsible for violative bulk tank milk samples as detected during regulatory control.     

Cold-temperature stability of five beta-lactam antibiotics in bovine milk and milk extracts prepared for liquid chromatography-electrospray ionization tandem mass spectrometry analysis

The stability of five major beta-lactam antibiotics (amoxicillin, ampicillin, cloxacillin, oxacillin, and penicillin G) in fortified milk and in milk extracts prepared for LC-ESIMS/MS analysis was studied at varying cold temperatures (4, -20, and -76 degrees C). Storage of milk samples at 4 degrees C resulted in measurable losses of all beta-lactams after 6 days (>50% in most cases). Slow degradation of penicillin G, cloxacillin, and oxacillin was observed in milk stored at -20 degrees C, but no losses were recorded at -76 degrees C over 4 weeks. All antibiotics showed good stability at all temperature tested in milk extracts prepared for LC-ESIMS/MS analysis. The results of this study emphasize adherence to adequate sample handling and storage protocols as to reflect residue levels at the time of sample submission.     

Validation of the Charm MRL-3 for fast screening of beta-lactam antibiotics in raw milk

The biochemicals utilized in the Charm MRL beta-Lactam test (8 min test) were applied to faster flowing lateral components to create a new 3 min, one-step beta-lactam test called Charm MRL-3 (Charm Sciences Inc., Lawrence, MA). This new test was validated at T&V-ILVO according to Commission Decision 2002/657/EC. The following analytical parameters were checked: test specificity, detection capability, and test robustness (impact of deviation of the test protocol, and impact of the milk composition, batch differences of reagents). Further, the suitability of the Charm MRL-3 to screen heat-treated milk or milk from animal species other than the cow was also tested. Finally, the test was integrated in the monitoring of dairy samples to check the occurrence of false-negative or false-positive results, and the test was also included in a national ring trial and an international proficiency study. The results proved that the Charm MRL-3 is a fast, simple, and reliable cows' milk test that can be used at the farm level in order to prevent tanker milk contamination, or at the entrance of the dairy plant to screen tanker milk for the presence of beta-lactam antibiotics.     

Trace determination of beta-lactam antibiotics in environmental aqueous samples using off-line and on-line preconcentration in capillary electrophoresis

A sensitive and reliable method using capillary zone electrophoresis with UV-diode array detection (CZE-DAD) has been developed and validated for trace determination of beta-lactam antibiotics in waste, well and river water matrices. Due to the lack of sensitivity of the UV-vis detection, a solvent extraction/solid-phase extraction (SPE) method applied for off-line preconcentration and cleanup of water samples, in combination with an on-line preconcentration methodology named large volume sample stacking (LVSS) have been applied. The analytes included nafcillin, dicloxacillin, cloxacillin, oxacillin, ampicillin, penicillin G and amoxicillin. Average recoveries for water samples fortified with the studied beta-lactams at different concentration levels (1.0, 2.0 and 4.0 microg/L) were ranging between 94 and 99%, with relative standard deviations (RSDs) lower than 10%. The precision, calculated as intra-day and inter-day standard deviations fell within acceptable ranges (3.3-7.2%). The limits of detection were estimated to range between 0.08 and 0.80 microgL(-1) for the studied compounds. All the samples analyzed were negative for all the analytes at these levels of concentration and the method showed its usefulness for the detection of these widely applied beta-lactam antibiotics in different kinds of waters.     

Use of SDS micelles for improving sensitivity, resolution, and speed in the analysis of beta-lactam antibiotics in environmental waters by SPE and CE

This study dealt with the potential of MEKC with LIF detection involving derivatization with sulfoindocyanine succinimidyl ester (Cy5) for the separation and determination of beta-lactam antibiotics (ampicillin, amoxicillin, cephradine, and cephalexin) in environmental water samples. Water samples of 50 mL were enriched by SPE by passage through a weak base-cation Amberlite(R) IRA-93 exchange column. SDS micelles play important roles in the whole analytical process by improving the yield (sensitivity) and the kinetics of the labeling reaction, the elution of the retained antibiotics from the SPE preconcentration system and the electrophoretic resolution of their Cy5-derivatives. The optimum procedure includes a derivatization step of the antibiotics at 25 degrees C for 10 min and direct injection for MEKC analysis, which is conducted within about 15 min using 15 mM SDS in the running buffer (35 mM sodium borate at pH 9.3). LODs from 30 to 45 ng/L and RSDs (within-day precision) from 3.5 to 5.9% were obtained for the antibiotics in water samples with average recoveries ranging from 96.4 to 99.4%. These results indicate that the method proposed is a straightforward and sensitive tool for the determination of these antibiotics in environmental water samples providing similar quantitative results to those using more expensive equipment like LC-electrospray MS/MS.     

Studies on residual antibacterials in foods. IV. Simultaneous determination of penicillin G, penicillin V and ampicillin in milk by high-performance liquid chromatography

A rapid and simple method for the simultaneous determination of penicillin G (PCG), penicillin V (PCV) and ampicillin (ABPC) in milk is described. The retention behaviour of these beta-lactam antibiotics in reversed-phase liquid chromatography with mobile phases containing sodium alkylsulphonate was studied. Good separations were obtained with methanol-water-0.2 M phosphate buffer (pH 4.0) (5:13:2) containing 11 mM sodium 1-heptanesulphonate and a LiChrosorb RP-18 column. The sample was pre-treated with a Sep-Pak C18 cartridge. The peaks corresponding to each beta-lactam antibiotics can be confirmed with the treatment using penicillinase. The recoveries from milk fortified with sodium PCG, potassium PCV and ABCP at levels of 0.5 and 0.1 micrograms/g each were generally better than 87% and the relative standard deviations were 1.17-4.98%. The detection limits corresponded to 0.03 microgram/g of these beta-lactam antibiotics in milk.     

Sequencing of bacitracin A and related minor components by liquid chromatography/electrospray ionization ion trap tandem mass spectrometry

A selective reversed-phase liquid chromatography/mass spectrometry (LC/MS(n)) method is described for the characterization of related compounds in commercial bacitracin samples. Mass spectral data for these polypeptide antibiotics were acquired on a LCQ ion trap mass spectrometer equipped with an electrospray ionization probe operated in the positive and negative ion mode. The LCQ ion trap is ideally suited for the sequencing of those linear side-chain cyclized peptides because it provides on-line LC/MS(n) capability. Using this method bacitracin A, 1-epibacitracin A, bacitracins B(1), B(2), B(3) and bacitracin F were sequenced and previous sequencing was confirmed. Bacitracins C(1), C(2), C(3), D, H(2) and H(3) were resolved chromatographically and their ring portion was sequenced for the first time. Four components not described in the literature (1-epibacitracin B(1), 1-epibacitracin B(2), 1-epibacitracin C(1) and H(4)) were sequenced completely for the first time. The main advantage of this hyphenated LC/MS(n) technique is the characterization of the related substances without time-consuming isolation and purification procedures.     

The potential of monoclonal antibodies against ampicillin for the preparation of a multi-immunoaffinity chromatography for penicillins.

Monoclonal antibodies (Mab) against ampicillin were prepared by immunization of mice with an ampicillin-keyhole limpet hemocyanin conjugate coupled by a glutaraldehyde method. Sensitivity and specificity of these antibodies were tested in a direct competitive enzyme immunoassay, in which an ampicillin-horseradish peroxidase conjugate prepared by a carbodiimide method served as the labelled antigen. According to their cross-reactivities with the other beta-lactam antibiotics, the Mabs could be divided into two groups, which are represented by the clones designated 1D1 and 3B5. While Mab 3B5 (IgG1) showed no major cross-reactions with the other penicillins frequently used in veterinary medicine except for amoxicillin (108%), Mab 1D1 (IgG2a) had marked cross-reactivities with most of the 17 tested beta-lactam antibiotics (e.g., amoxicillin 187%, penicillin G 31%, cloxacillin 30%, dicloxacillin 44%, and oxacillin 14%). The detection limits for ampicillin, calculated from the antibiotic concentration giving 30% binding inhibition, were 11.7 (Mab 3B5) and 16.6 ng ml-1 (Mab 1D1). To prepare multi-immunoaffinity chromatography columns, Mab 1D1 and a previously described antibody against cloxacillin (Mab 1F7) were each coupled to CNBr activated sepharose. The capacity of the resulting immunosorbents was approximately 6.6 and 5.4 micrograms ml-1 gel for ampicillin and cloxacillin, respectively. Recoveries of amoxicillin, ampicillin, cloxacillin, dicloxacillin, penicillin G and oxacillin (in buffer solutions) from the produced immunoaffinity columns were in the range from 67 to 100%.     

A quantitative method for residues of macrolide antibiotics in porcine kidney by liquid chromatography/tandem mass spectrometry

An LC/MS/MS-based multiresidue quantitative method was developed for the macrolides erythromycin A, neospiramycin I, oleandomycin, spiramycin I, tilmicosin, and tylosin A in porcine kidney tissues. The Canadian Food Inspection Agency (CFIA) had as part of its analytical scope an LC/UV method for quantification of residues of two macrolide antibiotics, tilmicosin and tylosin A, in the kidney, liver, and muscle of cattle, swine, and poultry. The method could not reliably detect concentrations below 10 microg/kg. To increase the scope of the CFIA's analytical capabilities, a sensitive multiresidue quantitative method for macrolide residues in food animal tissues was required. Porcine kidney samples were extracted with acetonitrile and alkaline buffer and cleaned-up using silica-based C18 SPE cartridges. Sample extracts were analyzed using LC/MS/MS with positive electrospray ionization. Fitness for purpose was verified in a single-laboratory validation study using a second analyst. The working analytical range was 5 to 50 microg/kg. LOD and LOQ were 0.5 to 0.6 microg/kg and 1.5 to 3.0 microg/kg, respectively. Limits of identification were 0.5 to 2.0 microg/kg. Relative intermediate precisions were 8 to 17%. Average absolute recoveries were 68 to 76%.     

Hydrophobicity of beta-lactam antibiotics. Explanation and prediction of their behaviour in various partitioning solvent systems and reversed-phase chromatography.

beta-Lactam antibiotics tend to undergo self-association in hydrophilic organic solvents, which leads to a strong dependence of their experimentally observable log P values on the partitioning conditions. As a result, most of the earlier obtained log P values for beta-lactam antibiotics cannot be applied as a common hydrophobicity measure, but they proved to be linearly related to each other and to a large body of reversed-phase chromatographic data. The retention of cephalosporins on reversed-phase liquid chromatographic columns is complicated by silanophilic interactions. However, under elution conditions that eliminate these silanophilic interactions, good correlations with log P data are observed, and a unified hydrophobicity scale for 90 penicillin and cephalosporin compounds could be evaluated. The Hansch and Leo additive scheme was shown to be valid for the calculation of hydrophobicities for penicillin and cephalosporin C-6(7) substituents, but it failed when applied to the prediction of cephalosporin C-3-substituent hydrophobicities. The hydrophobic increments for the sixteen most common cephalosporin C-3-substituents were empirically evaluated from literature data, and a simple equation was derived for an overall beta-lactam antibiotic hydrophobicity calculation. The proposed scale is valid for predicting the partitioning of most beta-lactam antibiotics in both hydrophilic and lipophilic organic-water systems, although it should be used with caution when applied to antibiotics containing additionally charged side-chains.     

Verification of cefmetazole and cefpodoxime proxetil contamination to other pharmaceuticals by liquid chromatography-tandem mass spectrometry

Cross-contamination is a critical issue for pharmaceutical manufacturing, especially for beta-lactam antibiotics. Thus, an analytical method for the simultaneous determination of beta-lactam antibiotics cefmetazole (CMZ) and cefpodoxime proxetil (CPDXPR) contaminants in non-beta-lactam pharmaceuticals was developed using high-performance liquid chromatography-tandem mass spectrometry. The developed method was found to be sensitive at the detection limit of 0.002 ppm for both compounds. Mean recoveries of CMZ and CPDXPR from olmesartan medoxomil (OLM) tablets were 96.7 to 102.2% and 88.9 to 94.2%, respectively. The developed method was successfully applied for the verification of CMZ and CPDXPR contamination to actually manufactured OLM tablets.     

Rapid forensic selected reaction monitoring liquid chromatography/mass spectrometry determination of ionophore antibiotics found at toxic levels in animal feeds

A rapid, accurate, and selective method was developed for the forensic determination of ionophore antibiotics in animal feeds. A simple extraction procedure and liquid chromatography/tandem mass spectrometry (LC/MS/MS) in the selected reaction monitoring (SRM) mode were used for rapid identification and confirmation of monensin and lasalocid in feed samples and for quantitation of monensin. Extracts from a homogenous portion of ground feeds were prepared using liquid-solid extraction and liquid-liquid extraction techniques. Feed extracts were further purified by a simple defatting and solvent wash step and then concentrated to dryness. Feed extract residues were reconstituted in 1 mL LC mobile phase and a 2 microL aliquot injected into the SRM LC/MS system. The latter system used a C18, 100 x 2.0 mm, LC column coupled to a PE-Sciex API 2000 tandem triple quadrupole mass spectrometer equipped with a TurbolonSpray LC/MS interface. Feed samples were extracted and analyzed for the determination of monensin and lasalocid within a couple of hours. Control feed samples fortified with monensin at concentrations from 50 ppb to 5 ppm provided a linear response and calibration curve across this range with a correlation coefficient of 0.996.     

Determination of lincomycin and tylosin residues in honey by liquid chromatography/tandem mass spectrometry

A simple and rapid analytical method was developed for the determination of lincomycin and tylosin residues in honey as part of field studies examining the efficacy and target animal safety of these antibiotics to control American foulbrood disease in honey bees. Residues of the antibiotics were determined using liquid chromatography/electrospray ionization tandem mass spectrometry (LC/ESI-MS/MS). Honey samples were diluted and injected directly into the LC/MS/MS system without additional cleanup by solid-phase extraction or liquid-liquid partitioning. A six-port valve system was utilized to selectively route eluant from the LC column into the mass spectrometer only during a relatively short portion of the chromatographic run corresponding to the elution of the analytes of interest. Minimal contamination of the MS source chamber was observed despite the analysis of large numbers of samples. Using internal standard quantitation, excellent accuracy and precision were obtained with no apparent matrix-to-matrix variation. Based on the analysis of fortified replicates, the mean percent deviation from the theoretical concentration and the percent relative standard deviation were both less than 10% for tylosin over an analytical range of 10-1000 microg/kg. Slightly higher mean percent deviations and relative standard deviations were observed for the analysis of lincomycin in fortified replicate samples. The method detection limits were determined to be 5 and 2 microg/kg for lincomycin and tylosin, respectively.