Temperature dependent surface and spectral modifications of nano V<Subscript>2</Subscript>O<Subscript>5</Subscript> films

Nanocrystalline V₂O₅ films have been deposited on glass substrates at 300°C substrate temperature using thermal evaporation technique and were subjected to thermal annealing at different temperatures 350, 400, and 550°C. X-ray diffraction (XRD) spectra exhibit sharper and broader characteristic peaks respectively indicating the rearrangement of nanocrystallite phases with annealing temperatures. Other phases of vanadium oxides started emerging with the rise in annealing temperature and the sample converted completely to VO₂ (B) phase at 550°C annealing. FESEM images showed an increase in crystallite size with 350 and 400°C annealing temperatures followed by a decrease in crystallite size for the sample annealed at 550°C. Transmission spectra showed an initial redshift of the fundamental band edge with 350 and 400°C while a blue shift for the sample annealed at 550°C, which was in agreement with XRD and SEM results. The films exhibited smart window properties as well as nanorod growth at specific annealing temperatures. Apart from showing the PL and defect related peaks, PL studies also supported the observations made in the transmission spectra.     

An insight into the influence of crystallite size on the performances of microsized spherical Li(Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode material composed of aggregated nanosized particles

Relationships between the performance and the crystallite size of the microsized spherical Li(Ni_0.5Co_0.2Mn_0.3)O₂ cathode material composed of aggregated nanosized primary particles have been comprehensively studied. The cathode material was synthesized by a high-temperature solid-state method. The results obtained by XRD, Rietveld refinement, SEM, HR-TEM, DSC, and galvanostatic test show that the crystallite size (XS) of Li(Ni_0.5Co_0.2Mn_0.3)O₂ is greatly affected by the temperature in the range of 750 to 820 °C. Most of all, the crystallite size plays a unique role in the performance of the material. That is, the electrochemical characteristics of Li(Ni_0.5Co_0.2Mn_0.3)O₂, such as discharge capacity, rate performance, and thermal stability, are closely related to the crystallite size. Furthermore, the retention of discharge capacity is determined by that of crystallite size in Li(Ni_0.5Co_0.2Mn_0.3)O₂ after 100 cycles.     

Magnetic phase separation in the (La<Subscript>0.3</Subscript>Sr<Subscript>0.7</Subscript>)<Subscript>0.5</Subscript>Ca<Subscript>0.5</Subscript>FeO<Subscript>3</Subscript> solid solution with a perovskite structure

The crystal structure and magnetic properties of the (La_0.3Sr_0.7)_0.5Ca_0.5FeO₃ solid solution with a perovskite structure have been investigated. The solid solution has been synthesized according to the high-pressure technique. The unit cell parameters have been refined using the Rietveld full-profile analysis under the assumption of the single-phase crystalline state and the two-phase model corresponding to the parent compositions. It follows from the calculations that the best agreement between the experimental data and the theoretical curve is observed for the two-phase model. The measurement of the magnetic properties also indicates the coexistence of two magnetic phases.     

The magnetic and hyperthermia studies of bare and silica-coated La<Subscript>0.75</Subscript>Sr<Subscript>0.25</Subscript>MnO<Subscript>3</Subscript> nanoparticles

The magnetic nanoparticles of La_0.75Sr_0.25MnO₃ perovskite manganite with a controlled size were prepared via sol–gel procedure, followed by thermal treatment and subsequent mechanical processing of the resulting raw product. The prepared materials were structurally studied by the XRD and TEM methods and probed by DC magnetic measurements. The nanoparticles of the mean crystallite sizes 11–40 nm exhibit T _C in the range of ≈310–347 K and the sample possessing 20-nm crystallites was identified as the most suitable for hyperthermia experiments. In order to obtain a colloidally stable suspension and prevent toxic effects, the selected magnetic cores were further encapsulated into silica shell using tetraethoxysilane. The detailed magnetic studies were focused on the comparison of the raw product, the bare nanoparticles after mechanical processing and the silica-coated nanoparticles, dealing also with effects of size distribution and magnetic interactions. The heating experiments were carried out in an AC field of frequencies 100 kHz–1 MHz and amplitude 3.0–8.9 kA m⁻¹ on water dispersions of the samples, and the generated heat was deduced from their warming rate taking into account experimentally determined thermal losses into surroundings. The experiments demonstrate that the heating efficiency of the coated nanoparticles is generally higher than that of the bare magnetic cores. It is also shown that the aggregation of the bare nanoparticles increases heating efficiency at least in a certain concentration range.     

HgO-added YB<Subscript>a2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7</Subscript>−δ superconductors

The HgO-added YB_a2Cu₃O_7−δ (YBCO) superconductor has been studied for its structural and superconducting properties. Polycrystalline YBCO samples were synthesized through solid-state reaction method by adding HgO in different concentrations without using oxygen annealing. All the samples showed a sharp superconducting transition temperature around 90 K. The X-ray diffraction patterns of all the samples revealed monophasic Y-123 nature. The structural studies were carried out by neutron scattering and Rietveld analysis. The neutron scattering revealed that Hg is not incorporated in the Y-123 system and has shown optimum oxygen concentration. The significant role played by the HgO is to provide oxygen ambient through its decomposition, thus changing the oxygen balance in favour of high Cu-valence state.     

Magnetic and dielectric properties of Mn<Subscript>0.2</Subscript>Ni<Subscript>0.8</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles synthesized by PEG-assisted hydrothermal method

We present a systematic investigation on the structural and magnetic properties of Mn_0.2Ni_0.8Fe₂O₄ nanoparticles synthesized by a polyethylene glycol (PEG)-assisted hydrothermal route. XRD, FT-IR, TEM and VSM were used for the structural, morphological, dielectric properties and magnetic investigation of the products, respectively. Average crystallite size of product was estimated using Line profile fitting as 6 ± 1 nm and particle size as 6.5 ± 1.0 nm from TEM micrographs. Magnetization measurements have shown that the particles have a blocking temperature of 134 K. Magnetization and the coercive field of the sample increase by decreasing the temperature. The conductivity measurements reveal the semiconducting behaviour for the sample. Temperature-dependent dielectric properties: dielectric permittivity (ε) and ac conductivity (σ_ac) for the sample were studied as a function of applied frequency in the range from 1 Hz to 3 MHz. These studies indicated that the dielectric dispersion curve for the sample showed usual dielectric dispersion which can be explained on the basis of Koop’s theory, which is based on the Maxwell–Wagner model for the interfacial polarization of homogeneous double structure.     

Controlled synthesis of photoluminescent Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> nanoparticles from metal-organic polymeric precursor

Bi₄Ti₃O₁₂ (BIT) nanoparticles with a narrow average particle size distribution in the range of 11–46 nm was synthesized via a metal-organic polymeric precursor process. The crystallite size and lattice parameter of BIT were determined by XRD analysis. At annealing temperatures >550 °C, the orthorhombic BIT compound with lattice parameters a = 5.4489 Å, b = 5.4147 Å, and c = 32.8362 Å was formed while at lower annealing temperatures orthorhombicity was absent. Reaction proceeded via the formation of an intermediate phase at 500 °C with a stoichiometry close to Bi₂Ti₂O₇. The particle size and the agglomerates of the primary particles have been confirmed by FESEM and TEM. The decomposition of the polymeric gel was ascertained in order to evaluate the crystallization process from TG-DSC analysis. Raman spectroscopy was used to investigate the lattice dynamics in BIT nanoparticles. In addition, investigation of the dependence of the visible emission band around the blue–green color emission on annealing temperatures and grain sizes showed that the effect of grain size plays important roles, and that oxygen vacancies may act as the radiative centers responsible for the observed visible emission band.     

Formation of new structural states in compressed BaTiO<Subscript>3</Subscript> nanopowders

The structural changes in BaTiO₃ nanocrystal powder and tablets have been probed via X-ray diffraction, scanning electron and transmission microscopy, and differential calorimetry after successive hightemperature annealing in air. It is shown that, beginning with the annealing temperature of 1200°C, significant amount of the Ba₂TiO₄ phase forms in the tablets together with the BaTiO₃ phase. This phase is equilibrium one; it practically vanishes when the annealing temperature decreases to 700–600°C; and this phase practically restored to the initial state when the annealing temperature is again increased to 1200°C. Annealing the powders causes no formation of new phases, but an increase in their crystallite sizes. A probable reason of the emergence of Ba₂TiO₄ phase in tablets and its absence in free powder is discussed, as well.     

Effect of PVA addition on formation of spray-deposited Sm<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>CoO<Subscript>3</Subscript> thin films on CeO<Subscript>2</Subscript> substrates

Nano-crystalline films of Sm_0.5Sr_0.5CoO₃ (SSC) have been formed on CeO₂ substrates by spraying stoichiometric aqueous solution containing Sm, Sr, and Co ions. Effect of polyvinyl alcohol (PVA) addition as a complexing agent in spray solution on stoichiometry, crystallite size, morphology, and transport properties of film are studied. The results showed that the SSC cathode had maximum crystallite size for 40% PVA addition. Electrical performance of film decreases with decrease in the particle size, while the electronic to ionic predominance transition temperature decreases with decreasing particle size. These films are studied for their potential application as a cathodic material in developing intermediate temperature solid oxide fuel cells.     

Metal-insulator transition in a radiation-disordered La<Subscript>0.85</Subscript>Sr<Subscript>0.15</Subscript>MnO<Subscript>3</Subscript> manganite

The temperature dependences of the electrical resistivity ρ(T) and the ac magnetic susceptibility χ(T, H = 0) are thoroughly investigated for a perovskite-like lanthanum manganite, namely, La_0.85Sr_0.15MnO₃, which is preliminarily exposed to neutron irradiation with a fluence _F = 2 × 10¹⁹ cm^?2 and then annealed at different temperatures ranging from 200 to 1000°C. The results of the electrical resistance measurements demonstrate that neutron irradiation of the samples leads to the disappearance of the low-temperature insulating phase. As the annealing temperature increases, the insulating phase is not restored and the manganite undergoes a transformation into a metallic phase. Analysis of the magnetic properties shows that, under irradiation, the ferromagnet-paramagnet phase transition temperature T_C decreases and the magnetic susceptibility is reduced significantly. With an increase in the annealing temperature, the phase transition temperature T_C and magnetic susceptibility χ(_{T, H} = 0) increase and gradually approach values close to those for an unirradiated sample. This striking difference in the behavior of the electrical and magnetic properties of the radiation-disordered La_0.85Sr_0.15MnO₃ manganite is explained qualitatively.     

Influence of heat treatment process in In<Subscript>2</Subscript>O<Subscript>3</Subscript>-MWCNTs as photoanode in DSSCs

Indium oxide-multi-walled carbon nanotubes (In₂O₃-MWCNTs) were prepared by sol-gel method for DSSCs. The synthesis of indium oxide (In₂O₃) was carried out by dissolving indium chloride (InCl₃) in a solvent of 2-methoxyethanol. Different annealing temperatures of 400, 450, 500, 550, and 600 °C were proposed in this study. The changes in the structural properties were analyzed by means of X-ray diffraction (XRD) and atomic force microscopy (AFM) analysis. The XRD spectrum estimated the average crystallite sizes of 3 nm for each sample. AFM results indicated very rough surface area of the films where it increased linearly from 1.8 to 11 nm as the annealing temperature increases. The In₂O₃-MWCNTs-based DSSC exhibited good photovoltaic performance with power conversion efficiency (η), photocurrent density (J _sc ), open circuit voltage (V _oc ), and fill factor (FF) of 1.13 %, 5.5 mA/cm², 0.53 V, and 0.42, respectively. Even though the film annealed at 450 °C exhibited low τ _eff, it achieved the greatest D _eff of 29.67 cm² s^?1 which provides an efficient pathway for the photogenerated electrons with minimum electron recombination loss that increased the J _sc and V _oc in the DSSC. The obtained structural and electron transport analysis was proposed as a suitable benchmark for In₂O₃-MWCNTs-based dye-sensitized solar cell (DSSCs) application. Hence, this study suggests that the optimum temperature for In₂O₃-MWCNTs is at annealing temperature of 450 °C prepared via sol-gel method.     

X-ray photoemission study of MgB<Subscript>2</Subscript> films synthesized from in-situ annealed MgB<Subscript>2</Subscript>/Mg multilayers

Superconducting MgB₂ films were obtained by in-situ annealing of precursor multilayers deposited at low substrate temperature by sputtering from a MgB₂ stoichiometric target and by thermal evaporation of pure Mg. After an in-situ annealing at 500–600 °C, the films showed a zero resistance critical temperature up to 31 K. The as-obtained MgB₂ films were investigated by X-ray photoelectron spectroscopy (XPS) and X-ray auger electron spectroscopy (XAES). The electronic structure was studied by monitoring the B 1s, Mg 2p, O 1s core-levels and the Mg KL₂L₃ Auger line. For comparison, the electronic structure of an MgB₂ commercial superconducting sputtering target, of a not-annealed precursor film and of a sample obtained by direct sputtering from the MgB₂ target have also been investigated. Electron spectroscopy showed that in the superconducting systems the Mg KL₂L₃ Auger line kinetic energy position is always higher by about 0.9 eV with respect to the energy position of the same Auger line measured in the non-superconducting samples. PACS 74.25Jb; 74.78.Bz; 74.70.Ad     

A study of the structure and properties of nanostructured ZrO<Subscript>2</Subscript>-Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powders

The correlation between temperature treatment conditions and the ratio of components in nanostructured fibrous powders with a composition of ZrO₂-Y₂O₃-Al₂O₃ and their porous crystal structure and physicochemical properties is studied. The dependences of the ratio between zirconia tetragonal and monoclynic phases on the treatment temperature and the alumina content are found to have a nonmonotonic character. The growth of zirconia crystallite size is suppressed by introduced nanocrystalline alumina in a temperature range of 600–1200°C, which is caused by the processes of ternary solid solution formation. The bulk and picnometric density values of materials are proportional to the temperature of heat treatment. The temperature dependence of the specific surface and the size of oxide grain particles has an inversely proportional character. With increasing alumina content in the powders, the specific surface increases, while the picnometric and bulk densities decrease.     

Morphology modification of TiO<Subscript>2</Subscript> nanotubes by controlling the starting material crystallite size for chemical synthesis

TiO₂ nanotubes (NTs) were prepared by low-temperature chemical synthesis using anatase TiO₂ particles with different crystallite sizes in a NaOH solution followed by water washing and HCl neutralization. The synthesized TiO₂ NTs showed diverse morphologies depending on the starting materials. The crystallite size of TiO₂ raw materials increased with an increase in annealing temperature, and larger TiO₂ NTs, around 31 nm in diameter, were obtained from large raw powder with a crystallite size of 117 nm. X-ray diffraction and Raman spectroscopy revealed that the obtained TiO₂ NT exhibited lower crystallinity; however, Raman vibration seems to be more likely than a rutile structure.     

Size-Dependent Effects in EPR and Luminescence Spectra of NH<Subscript>4</Subscript>BPh<Subscript>4</Subscript> Excited States: from Bulk to Nanoparticles

Photoexcited states of NH₄BPh₄ (TPhBA) particles embedded in mesoporous frameworks of different pore sizes were studied by combined electron paramagnetic resonance (EPR), optical and photoluminescence techniques. A distribution of triplet states with short and long electron–hole distances was found. While EPR studies on TPhBA bulk sample suggested that the formation of electron–hole pairs upon the excitation was caused by electron capture on electron traps, the samples in mesoporous frameworks exhibit two ways of the pair formation. The first one is attributed to the capture on phenyl rings and another one is to be thought as the capture of electrons on adsorbed oxygen molecules. These results are also consistent with the thermoluminescence spectra and EPR studies of the photoexcited samples during annealing.     

Two-phase paramagnetic-ferromagnetic state of La<Subscript>0.7</Subscript>Pb<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> single-crystal lanthanum manganite

Two phases, paramagnetic and ferromagnetic, were shown by the magnetic resonance method to coexist below the temperature T _C in La_0.7Pb_0.3MnO₃ single crystals exhibiting colossal magnetoresistance. The magnetic resonance spectra were studied in the frequency range 10–78 GHz. The specific features in the behavior of the spectral parameters were observed to be the strongest at the temperatures corresponding to the maximum magnetoresistance in the crystals. The concentration ratios of the paramagnetic and ferromagnetic phases in the samples were found to be sensitive to variations in temperature and external magnetic field. This behavior suggests realization of the electronic phase separation mechanism in the system under study.     

Structural aspects of solid-state amorphization in Eu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript> single crystals

X-ray diffraction studies of Eu₂(MoO₄)₃ single crystals were performed, which demonstrate that, in contrast to polycrystalline samples, these crystals do not exhibit amorphous-like diffraction patterns during the reverse transition from the high-pressure phase into the initial β phase; rather, the diffracted intensity in their diffraction patterns decreases significantly to the background. Such a diffraction pattern can be explained under the assumption that a single crystal is divided into small (nanoscopic) regions inside which the lattice parameters of the high-pressure phase and the initial β phase change continuously. The simultaneous recovery of the single-crystal state of the β phase from this intermediate state in all nanoscopic regions as the annealing temperature increases indicates that nanocrystals in this state are structurally correlated with each other. This result suggests that the halo-type diffraction patterns of polycrystalline samples reflect an intermediate state between the high-pressure phase and the β phase in every initial crystallite (as in the single crystals) rather than being caused by an amorphous structure of the sample. In this case, the total diffraction pattern of differently oriented crystallites gives an amorphous-like diffraction pattern reflecting the contributions from numerous various crystallographic planes involved in diffraction.     

Electronic properties of strain-disordered Ni<Subscript>2.16</Subscript>Mn<Subscript>0.84</Subscript>Ga alloy

The effect of ultrarapid quenching from the melt and severe plastic torsional deformation under high pressure on the crystalline structure and the electrical, optical, and magnetic properties of a Ni_2.16Mn_0.84Ga alloy was studied. The electrical properties are discussed in terms of the Mott two-band model. The peculiarities of the magnetic properties are associated with the magnetism of itinerant electrons. The optical properties correlate with the variations in the electronic spectrum upon disordering of the alloy that follow from the results of the available energy-band-structure calculations.     

Magnetic and Magnetodielectric Properties of Ho<Subscript>0.5</Subscript>Nd<Subscript>0.5</Subscript>Fe<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript>

The magnetic and magnetodielectric properties of Ho_0.5Nd_0.5Fe₃(BO₃)₄ ferroborate with the competing Ho–Fe and Nd–Fe exchange couplings have been experimentally and theoretically investigated. Step anomalies in the magnetization curves at the spin-reorientation transition induced by the magnetic field B ║ c have been found. The spontaneous spin-reorientation transition temperature T_SR ≈ 8 K has been refined. The measured magnetic properties and observed features are interpreted using a single theoretical approach based on the molecular field approximation and calculations within the crystal field model of the rare-earth ion. Interpretation of the experimental data includes determination of the crystal field parameters for Ho³⁺ and Nd³⁺ ions in Ho_0.5Nd_0.5Fe₃(BO₃)₄ and parameters of the Ho–Fe and Nd–Fe exchange couplings.     

Synthesis and microstructure of Co/Ni: MgGa<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

This report discusses the preparation and microstructure of Co/Ni co-doped MgGa₂O₄ nanoparticles. The nanoparticles with the size of 20–55 nm were synthesized by sol-gel method. The phase and crystallinity were confirmed by X-ray powder diffraction (XRD) pattern. The particle size was estimated according to XRD data and transmission electron microscopy. The electronic structure was studied using X-ray photoelectron spectroscopy (XPS). The XPS studies showed that Ga³⁺ ions possess tetrahedral and octahedral sites of spinel structure and the inverse degree (two times of the fraction of tetrahedral Ga³⁺ ions) has increased with the increase of the doping concentration of Co²⁺ and Ni²⁺ ions. For Co/Ni co-doped MgGa₂O₄, two broad absorption bands of 350~500 and 550~700 nm were observed in the absorption spectra. The broad band at 350~500 nm was assigned to the combination of the absorption of octahedral Co²⁺ and Ni²⁺ ions, whereas the absorption band at 550~700 nm is mainly due to tetrahedrally coordinated Co²⁺ ions and octahedrally coordinated Ni²⁺ ions.