Glass transition temperature and thermal decomposition of cellulose powder

Cellulose powder and cellulose pellets obtained by pressing the microcrystalline powder were studied using differential scanning calorimetry (DSC), differential thermal analysis (DTA), and thermal gravimetry (TG). The TG method enabled the assessment of water content in the investigated samples. The glass phase transition in cellulose was studied using the DSC method, both in heating and cooling runs, in a wide temperature range from −100 to 180 °C. It is shown that the DSC cooling runs are more suitable for the glass phase transition visualisation than the heating runs. The discrepancy between glass phase transition temperature T _g found using DSC and predictions by Kaelbe’s approach are observed for “dry” (7 and 5.3% water content) cellulose. This could be explained by strong interactions between cellulose chains appearing when the water concentration decreases. The T _g measurements vs. moisture content may be used for cellulose crystallinity index determination.     

Effect of Inorganic Solids,Wax to Asphaltene Ratio,and Water Cut on the Stability of Water-in-Crude Oil Emulsions

The formation of stable water-in-crude oil emulsions during petroleum production and refinery may create sever and costly separation problems. It is very important to understand the mechanism and factors contributing to the formation and stabilization of such emulsions for both great economic and environmental development. This article investigates some of the factors controlling the stability of water-in-crude oil emulsions formed in Burgan oil field in Kuwait. Water-in-crude oil emulsion samples collected from Burgan oil filed have been used to separate asphaltenes, resins, waxes, and crude oil fractions. These fractions were used to prepare emulsion samples to study the effect of solid particles (Fe₃O₄) on the stability of emulsions samples. Results indicate that high solid content lead to higher degree of emulsion stability. Stability of emulsion samples under various waxes to asphaltenes (W/A) ratios have also been tested. These tests showed that at low W/A content, the emulsions were very stable. While at a wax to asphaltene ratio above 1 to 1, the addition of wax reduced emulsion stability. Stability of emulsion samples with varying amount of water cut has also been investigated. Results indicated that stability and hence viscosity of emulsion increases as a function of increasing the water cut until it reaches the inversion point where a sharp decline in viscosity takes place. This inversion point was found to be approximately at 50% water cut for the crude oils considered in this study.     

Dehydration studies of Co(II), Cu(II) and Zn(II) methanesulfonates

The dehydration process of Co(II), Cu(II) and Zn(II) methanesulfonates was studied by thermogravimetry/derivative thermogravimetry (TG/DTG) and differential scanning calorimetry (DSC) techniques in dynamic N₂ atmosphere. The TG/DTG curves show that all of them contain four crystallization water molecules, which are lost in two steps. The peak temperature and dehydration enthalpies ΔH were measured from DSC curves for each compound. The effect of procedural variables on the TG and DSC curves was investigated. In this work, the procedural variables included heating rate, Al pan state (unsealed and sealed) and sample mass.     

Thermal analysis of water and magnesium hydroxide content in commercial pharmaceutical suspensions milk of magnesia

A standard protocol was developed to determine the water content by thermal analysis of milk of magnesia (MoM). Differential scanning calorimetry (DSC) and thermogravimetry (TG) were used in a novel manner for examining the physical characteristics of the commercial pharmaceutical suspensions. Moisture analyzer and oven-dry methods validate the proposed protocol. MoM consists primarily of water and magnesium hydroxide [Mg(OH)₂]. Experimental design of the thermal analysis parameters were considered including sample size, flowing atmosphere, sample pan, and heating rate for both DSC and TG. The results established the optimum conditions for minimizing heat and mass transfer effect. Sample sizes used were: (5?C15?mg) for DSC and (30?C50?mg) for TG. DSC analysis used crimped crucibles with a pinhole, which allowed maximum resolution and gave well-defined mass (water) loss. TG analysis used a heating rate of 10?°C/min^?1 in an atmosphere of nitrogen. The heat of crystallization, heat of fusion, and heat of vaporization of unbound water are 334, 334, and 2,257?Jg^?1, respectively (Mitra et al. Proc NATAS Annu Conf Therm Anal Appl 30:203?C208, 2002). The DSC average water content of (MoM) was 80?wt% for name brand and 89.5?wt% for generic brand, based on the relative crystallization, melting and vaporization heats/Jg^?1 of distilled water in the recently purchased (2011) MoM samples. The TG showed a two-step process, losing water at 80?C135?°C for unbound water and bound water (MgO·H₂O) at 376?C404?°C, yielding a total average water loss of 91.9?% for name brand and 90.7?% for generic brand by mass. The difference between the high-temperature TG and the lower-temperature DSC can be attributed for the decomposition of magnesium hydroxide or MgO·H₂O. Therefore in performing this new approach to water analysis by heating to a high temperature decomposed the magnesium hydroxide residue. It was determined that the TG method was the most accurate for determining bound and unbound water.     

Calculation of smoothing factors for the comparison of DSC results

Complex mixtures of long chain organic compounds often show overlapping glass transition temperatures (T _gs) when analyzed by differential scanning calorimetry (DSC) or modulated DSC (MDSC). In such cases, subjective and inconsistent smoothing of data acquired under different conditions can lead to the misinterpretation of results. A quantitative method for the selection of smoothing factors for the analysis and comparison of (M)DSC results is presented. The method is most useful for the analysis of the derivative of the heat capacity, dC _p/dt or dC _p/dT, plots which best highlight overlapping T _gs. Four equations are shown to relate the heating rate and the smoothing factor. The equations allow a comparison of data acquired i) at different heating rates and plotted vs. temperature, ii) at a single heating rate and plotted vs. both time and temperature, i.e., dC _p/dt vs. dC _p/dT, iii) at different heating rates and plotted vs. both time and temperature, and iv) at different heating rates, and shown exclusively in the time domain. Examples of the use of the equations are provided for the analysis of bitumen, a complex mixture of natural origin.     

A statistical model for the optimization of dsc performance in the evaluation of drugs for preformulation studies

Differential scanning calorimetry (DSC) is a thermal analytical tool for preformulation studies. Extrapolated melting temperature (T_P) and heat of fusion (ΔH_f) can be used as parameters for optimizing the DSC performance. Two model pharmaceuticals acetaminophen and nicotinamide are used in this study. Using a factorial design for the experimental model and matrix analysis the results, the effect of sample mass, heating rate and the nitrogen flow rate were evaluated on the ΔH_f values and T_P values. Two levels for each of the procedural variables were used as a balanced experimental design with two sample sizes, two heating rates and two nitrogen flow rates. It was found that the change in the heating rate caused significant changes in the ΔH_f values but not the T_p values for acetaminophen. However, no significant effect was found for the T_p value but ΔH_f value was affected to a certain extent for nicotinamide.     

Interactions and antioxidant stability of sesamol in dry-emulsions

Dry emulsions prepared from saccharose (SAC), Labrafil^? M 1944 CS, sesamol (SEOH), and hydroxypropylmethylcellulose (HPMC) or sodium caseinate (SC) by grinding or dissolution, and different desiccation techniques (spray (SD)- or freeze (FD)-drying, or heating at 60 °C) were investigated to determine possible interactions between mixture components. The goal of this study was to determine the best formulation which will regenerate perfectly, after water dilution of dry emulsions, the initial liquid emulsion with the same characteristics that before drying. The morphological state of SAC and dry emulsions were determined by scanning electron microscopy analysis (SEM) analysis. Glass transition temperature, and melting (endothermic), decomposition (endothermic), oxidation (exothermic) peak temperatures and enthalpies were measured by differential scanning calorimetry (DSC). The antioxidant activity of emulsions was evaluated through their ability to reduce 1,1-diphenyl-2-picrylhydrazil (DPPH) free radical. SEM analysis showed that SD-prepared, SC-containing dry emulsions formed better spherical particles with smooth surface at about 5 μm diameter as compared to emulsion containing HPMC. These former emulsions also showed more thermal stability by DSC. The combined results of the three analytical techniques emphasized the importance of the dry emulsion process regarding the efficiency and the thermal stability of antioxidant substances. A specific physical and/or chemical combination (such as hydrogen bond) sufficiently stable, at about 150 °C, could be suggested when the technique used for dry emulsion preparation was SD. After water dilution, this dry emulsion obtained from quaternary mixture: SAC, Labrafil^?, SEOH and SC, will regenerate the initial liquid emulsion with the same characteristics that before drying.     

Application of hydrophobically modified water‐soluble polyacrylamide conjugated with poly(oxyethylene)‐co‐poly(oxypropylene) surfactant as emulsifier

Hydrophobically modified polyacrylamide (PAAm) was prepared by grafting PAAm with block copolymer of poly(ethylene oxide) and poly(propylene oxide), PEO‐PPO‐PEO, by melt method in the presence of benzoyl peroxide as initiator. The chemical structure of the graft copolymer was determined by FTIR and ¹HNMR analyses. The surface tension, critical micelle concentration, and surface activities were determined at different temperatures. Surface parameters such as surface excess concentration (Γ_max), the area per molecule at interface (A_min), and the effectiveness of surface tension reduction (Π_CMC) were determined at different temperatures from the adsorption isotherms of the prepared surfactants. The prepared surfactant was tested as emulsifier for water with xylene, cyclohexane, or petroleum crude oil synthetic emulsions. Copyright © 2010 John Wiley & Sons, Ltd.     

Ring opening polymerization of epoxides with urea‐derivatives of 4‐aminopyridine as thermally latent anionic initiator

In this study, a series of urea‐derivatives of 4‐aminopyridine (4AP) were evaluated as thermally latent initiators for the anionic ring‐opening polymerization of diglycidyl ether of bisphenol A (DGEBA). The urea‐derivatives were synthesized by the reactions of 4AP with the corresponding iso(thio)cyanates (phenyl isocyanate, tert‐butyl isocyanate, methylene diphenyl diisocyanate, and phenyl isothiocyanate). The ability of the urea‐derivatives as latent initiators was investigated with differential scanning calorimetry (DSC): Upon heating formulations comprised of DGEBA and the urea‐derivatives in a heating rate at 10 °C/min, the resulting DSC profiles indicated exothermic peaks to confirm that DGEBA underwent the polymerization efficiently. The corresponding DSC‐peak top temperatures (T_{peak top}) was higher than that observed for the formulation comprised of DGEBA and pristine 4AP, to clarify that the urea are useful initiators with thermal latency. A possible mechanism for the initiation step involves the thermal dissociation of the urea into 4AP and the corresponding isocyanates. 4AP thus generated readily initiated the ring‐opening polymerization of epoxide. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2518–2522     

Thermal transitions and fat droplet stability in ice-cream mixmodel systems

We studied thermal transitions and physical stability of oil-in-water emulsions containing different milk fat compositions, arising from anhydrous milk fat alone (AMF) or in mixture (2:1 mass ratio) with a high melting temperature (AMF–HMT) or a low melting temperature (AMF–LMT) fraction. Changes in thermal transitions in bulk fat and emulsion samples were monitored by differential scanning calorimetry (DSC) under controlled cooling and reheating cycles performed between 50 and –45°C (5°C min^–1). Comparison between bulk fat samples and emulsions indicated similar values of melting completion temperature, whereas initial temperature of fat crystallization (T_onset) seemed to be differently affected by storage temperature depending on triacylglycerols (TAG) composition. After storage at 4°C, T_onset values were very similar for emulsified and non-emulsified AMF–HMT blend, whereas they were lower (by approx. 6°C) for emulsions containing AMF or mixture of AMF–LMT fraction. After storage at –30°C, T_onset values of re-crystallization were higher in emulsion samples than in bulk fat blends, whatever the TAG fat composition. Light scattering measurements and fluorescence microscopic observations indicated differences in fat droplet aggregation-coalescence under freeze-thaw procedure, depending on emulsion fat composition. It appeared that under quiescent freezing, emulsion containing AMF–LMT fraction was much less resistant to fat droplet aggregation-coalescence than emulsions containing AMF or AMF–HMT fraction. Our results indicated the role of fat droplet liquid-solid content on emulsion stability.     

Thermal properties of freezing bound water restrained by sodium lignosulfonate-based polyurethane hydrogels

In order to develop a new functional product from lignin, sodium lignosulfonate (LS)-based polyurethane (LSPU) hydrogels were prepared from LS and hexamethylene diisocyanate (HDI) derivatives in water. Isocyanate/hydroxyl group ratio (NCO/OH ratio) was varied from 0.05 to 0.8 mol mol⁻¹, and water content (W_c = mass of water/mass of dry sample) of the obtained LSPU hydrogels was varied from 0 to 3.0 g g⁻¹. Phase transition behavior of hydrogels with various W_c’s was investigated by differential scanning calorimetry (DSC) and thermogravimetry (TG). In DSC heating curve of LSPU hydrogels, glass transition, cold crystallization, melting and liquid crystallization were observed. Cold crystallization, two melting peaks and variation of melting enthalpy indicate that three kinds of water, i.e., non-freezing water, freezing bound water and free water, exist in LSPU hydrogel. Glass transition temperature (T_g) decreased from 230 to 190 K in a W_c range where non-freezing water was formed in the hydrogel. T_g increased when freezing bound water was formed in the system. T_g leveled off in a W_c range where normal ice was formed. The effect of NCO/OH ratio on molecular motion of LSPU hydrogel is examined based on T_g and heat capacity difference at T_g (ΔC_p). Water vaporization curve measured by TG also indicates the presence of bound water which evaporates at a temperature higher than ca. 410 K. By atomic force microscopic observation, the size of molecular bundle of LSPU hydrogel is calculated and compared with that of LS-water system. By cross-linking, the height of molecular bundle decreased from ca. 3–1 nm and lignin molecules extend in a flat structure.

     

Performance evaluation of a new nanocomposite polymer gel for water shutoff in petroleum reservoirs

Abstract

A new polymer gel nanocomposite is fabricated for excess water production control (water shut off) in petroleum reservoirs and its rheological behavior is evaluated in the presence of sea water and formation water at the temperature of 100?°C. It is shown that at a high salinity without using SiO₂ nanoparticles, the elastic modulus of synthesized polymer gel in the presence of sea water and formation water are 12.5?Pa and 9.8?Pa respectively. However by incorporation of SiO₂ nanoparticles in the polymer gel matrix, the elastic modulus of synthesized polymer gel in the presence of sea water and formation water can be improved to 13.56?Pa and 11.57?Pa respectively, which is quite interesting from reservoir engineering viewpoint. Equilibrium Swelling Ratio (ESR) of the nanocomposite polymer gel in sea water and formation water decreases as the concentration of the SiO₂ increases. Thermal stability of the polymer gel is investigated by differential scanning calorimetry (DSC) measurements. The inflexion temperature of the polymer gel is improved by incorporation of 2000?ppm SiO₂ nanoparticles. The fabricated polymer gel nanocomposite in this work can have potential application in reduction of excess water production during enhanced oil recovery (EOR) operations in petroleum industry.     

Curing behavior of epoxy resins with a series of novel curing agents containing 4,4′-biphenyl and varying methylene units

A new homologous series of curing agents (LCECAn) containing 4,4′-biphenyl and n-methylene units (n = 2, 4, 6) were successfully synthesized. The curing behaviors of a commercial diglycidyl ether of bisphenol-A epoxy (E-51) and 4,4′-bis(2,3-epoxypropoxy)biphenyl (LCE) by using LCECAn as the curing agent have been investigated by differential scanning calorimetry (DSC), respectively. The Ozawa equation was applied to the curing kinetics based upon the dynamic DSC data, and the isothermal DSC data were fitted using an autocatalytic curing model. The glass transition temperatures (T _g) of the cured epoxy systems were determined by DSC upon the second heating, and the thermal decomposition temperatures (T _d) were obtained by thermogravimetric (TG) analyses. The results show that the number of methylene units in LCECAn has little influence on the curing temperatures of E-51/LCECAn and LCE/LCECAn systems. In addition, the activation energies obtained by the dynamic method proved to be larger than those by the isothermal method. Furthermore, both the T _g and T _d of the cured E-51/LCECAn systems and LCE/LCECAn systems decreased with the increase in the number of methylene units in LCECAn.     

Calorimetric study and thermal analysis of berberine sulphate

The heat capacities of berberine sulphate [(C₂₀H₁₈NO₄)₂SO₄·3H₂O] were measured from 80 to 390 K by means of an automated adiabatic calorimeter. Smoothed heat capacities, H _T-H _298.15 and S _T-S _298.15 were calculated. The loss of crystalline water started at about 339.3±0.2 K, and its peak temperature was 365.8±0.6 K. The peak temperature of decomposition for berberine sulphate was at about 391.4±0.4 K by DSC curve. TG-DTG analysis of this material was carried out in temperature range from 310 to 970 K. TG and DSC curves show that there is no melting in the whole heating process. This revised version was published online in August 2006 with corrections to the Cover Date.     

Following the crystallisation of Bi2Mo2O9 catalyst by combined XRD/QuEXAFS

The formation ofβ-phase Bi₂Mo₂O₉ catalyst from a precursor precipitate has been studied using thein situ combined XRD/QuEXAFS technique and DSC during calcination. Accordingly the precursor was observed to undergo a number of changes in both the molybdenum (VI) coordination and long-range ordering during this heating. Initially the two other forms of bismuth molybdate (α-andγ-phases) were observed to form from the poorly crystalline precursor at about 230°C, however, theβ-phase eventually crystallised after prolonged heating at 560°C. Dedicated to Professor C N R Rao on his 70th birthday     

Glass transition kinetics of some Se-Te-Ag chalcogenide glasses

Summary The present paper reports the Differential Scanning Calorimetric (DSC) study of some Ag doped Se-Te chalcogenide glasses. DSC runs were taken at different heating rates. Well-defined endothermic and exothermic peaks were obtained at glass transition and crystallization temperatures. The variation of glass transition temperature T_gwith Ag concentration has been studied. It has been found that T_gdecreases with increase in Ag concentration. The heating rate dependence of T_gis used to evaluate the activation energy of glass transition (DE_t). The value of<span style='font-size:10.0pt; font-family:"SymbolProp BT";mso-bidi-font-family:"SymbolProp BT"'>DE_thas been found to increase with increase in Ag concentration followed by nearly constant value at higher concentrations of Ag.     

New insights into the multiple melting behaviors of the semicrystalline ethylene‐hexene copolymer: Origins of quintuple melting peaks

A semicrystalline ethylene‐hexene copolymer (PEH) was subjected to a simple thermal treatment procedure as follows: the sample was isothermally crystallized at a certain isothermal crystallization temperature from melt, and then was quenched in liquid nitrogen. Quintuple melting peaks could be observed in heating scan of the sample by using differential scanning calorimeter (DSC). Particularly, an intriguing endothermic peak (termed as Peak 0) was found to locate at about 45 °C. The multiple melting behaviors for this semicrystalline ethylene‐hexene copolymer were investigated in details by using DSC. Wide‐angle X‐ray diffraction (WAXD) technique was applied to examine the crystal forms to provide complementary information for interpreting the multiple melting behaviors. Convincing results indicated that Peak 0 was due to the melting of crystals formed at room temperature from the much highly branched ethylene sequences. Direct heating scans from isothermal crystallization temperature (T_c, 104–118 °C) were examined for comparison, which indicated that the multiple melting behaviors depended on isothermal crystallization temperature and time. A triple melting behavior could be observed after a relatively short isothermal crystallization time at a low T_c (104–112 °C), which could be attributed to a combination of melting of two coexistent lamellar stack populations with different lamellar thicknesses and the melting‐recrystallization‐remelting (mrr) event. A dual melting behavior could be observed for isothermal crystallization with both a long enough time at a low T_c and a short or long time at an intermediate T_c (114 °C), which was ascribed to two different crystal populations. At a high T_c (116–118 °C), crystallizable ethylene sequences were so few that only one single broad melting peak could be observed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2100–2115, 2008     

On the origin of the multiple melting behavior in poly(ethylene naphthalene‐2,6‐dicarboxylate): Microstructural study as revealed by differential scanning calorimetry and X‐ray scattering

In this article a study on the melting behavior and microstructure of semicrystalline poly(ethylene naphthalene‐2,6‐dicarboxylate) (PEN) prepared by crystallization from the glass under different annealing conditions is presented. The influence of the annealing temperature (T_a), annealing time (t_a), and the heating rate (R_h) at which T_a is reached on the endothermic behavior of the samples was investigated by means of differential scanning calorimetry (DSC). A dual melting behavior appeared for low R_h values (2 deg · min⁻¹) within the range of 145 °C < T_a < 250 °C and 1 min ≤ t_a. ≤ 16 h. Samples subjected to fast heating rates (R_h = 200 deg · min⁻¹) to reach a T_a ≥ 230 °C showed DSC traces in which a transition is observed from three peaks to a single melting peak when t_a increases in the 30–240 min range. On the basis of the DSC results, PEN samples were prepared displaying single or dual endothermic behavior. The microstructure of these samples was studied by wide (WAXS) and small‐angle X‐Ray scattering (SAXS) techniques. The SAXS data were analyzed using the correlation function and interface distribution function formalisms, respectively. In samples with a single melting behavior, microstructural parameters such as the long spacing, the amorphous and the crystalline phase thicknesses are consistent with a lamellar stacking model in which the thickness distributions of both phases are almost the same. For samples exhibiting two melting endotherms, a dual lamellar model, which is in agreement with the experimental results is proposed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1167–1182, 2000     

Hydrophilic and hydrophobic copolymer systems based on acrylic derivatives of pyrrolidone and pyrrolidine

This article deals with the synthesis of hydrophilic methacrylic monomers derived from ethyl pyrrolidone [2‐ethyl‐(2‐pyrrolidone) methacrylate (EPM)] and ethyl pyrrolidine [2‐ethyl‐(2‐pyrrolidine) methacrylate (EPyM)] and their respective homopolymers. For the determination of their reactivity in radical copolymerization reactions, both monomers were copolymerized with methyl methacrylate (MMA), the reactivity ratios being calculated by the application of linear and nonlinear mathematical methods. EPM and MMA had ratios of r_EPM = 1.11 and r_MMA = 0.76, and this indicated that EPM with MMA had a higher reactivity in radical copolymerization processes than vinyl pyrrolidone (VP; r_VP = 0.005 and r_MMA = 4.7). EPyM and MMA had reactivity ratios of r_EPyM = 1.31 and r_MMA = 0.92, and this implied, as for the EPM–MMA copolymers, a tendency to form random or Bernoullian copolymers. The glass‐transition temperatures of the prepared copolymers were determined by differential scanning calorimetry (DSC) and were found to adjust to the Fox equation. Total‐conversion copolymers were prepared, and their behavior in aqueous media was found to be dependent on the copolymer composition. The swelling kinetics of the copolymers followed water transport mechanism case II, which is the most desirable kinetic behavior for a swelling controlled‐release material. Finally, the different states of water in the hydrogels—nonfreezing water, freezing bound water, and unbound freezing water—were determined by DSC and found to be dependent on the hydrophilic and hydrophobic units of the copolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 395–407, 2003     

Thermal expansion of liquid crystalline amphiphilic di-block copolymer observed by simultaneous DSC-XRD

Phase transition process of PEO_m-b-PMA(Az)_n was investigated by the simultaneous DSC-XRD measurement using the synchrotron radiation facility. Four endothermic DSC peaks were observed during heating process. These DSC peaks were assigned to the melting of PEO, the transition from SmX, which is a mixture of super-cooled SmC and crystal, to SmC, from SmC to SmA, and from SmA to isotropic liquid state as determined by XRD profiles. In SmC phase, the liner expansion coefficient calculated from the spacing variation of the smectic layer distance was larger than that of the other phases. This result reflected the fact azobenzene moieties in the long-side chains of PMA(Az)_n forming the smectic layers and then they were tilted and stood up during the heating process.