Reverse Homogeneous Liquid–Liquid Extraction as a Miniaturized Method for Extraction of Aflatoxins from Pistachio and Wheat and LC Post-column Derivatization-Fluorescence Detection

A rapid and simple quantitative method for the simultaneous determination of the four aflatoxins (AFs) B1, B2, G1 and G2 was developed using reverse homogeneous liquid–liquid extraction (RHLEE) and HPLC post-column derivatization-fluorescence (HPLC-FL) detection. The method based on the rapid extraction of AFs from a methanolic sample into chloroform after addition of water containing KBr, with a method we called reverse homogeneous liquid–liquid extraction. Recoveries were in the range of 88–125% and the limits of detection were between 0.001–0.042 ng g^?1 for different AFs. Wheat and pistachio were chosen for the analysis of real samples and the method was also successfully applied to a FAPAS^® TEST MATERIAL (T04151).     

Liquid–liquid miscibility and volumetric properties of aqueous solutions of ionic liquids as a function of temperature

The volumetric properties of seven {water + ionic liquid} binary mixtures have been studied as a function of temperature from (293 to 343) K. The phase behaviour of the systems was first investigated using a nephelometric method and excess molar volumes were calculated from densities measured using an Anton Paar densimeter and fitted using a Redlich–Kister type equation. Two ionic liquids fully miscible with water (1-butyl-3-methylimidazolium tetrafluoroborate ([C₁C₄Im][BF₄]) and 1-ethyl-3-methylimidazolium ethylsulfate ([C₁C₂Im][EtSO₄])) and five ionic liquids only partially miscible with water (1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C₁C₂Im][NTf₂]), 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C₁C₄Im][NTf₂]), 1-butyl-3-methylimidazolium hexafluorophosphate ([C₁C₄Im][PF₆]), 1-butyl-3-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([C₁C₄Pyrro][NTf₂]), and butyltrimethylammonium bis(trifluoromethylsulfonyl)imide ([N₄₁₁₁][NTf₂])) were chosen. Small excess volumes (less than 0.5 cm³ · mol^?1 at 298 K) are obtained compared with the molar volumes of the pure components (less than 0.3% of the molar volume of the pure ionic liquid). For all the considered systems, except for {[C₁C₂Im][EtSO₄] + water}, positive excess molar volumes were calculated. Finally, an increase of the non-ideality character is observed for all the systems as temperature increases.     

Determination of Aristocularine Enantiomers by Dispersive Liquid–Liquid Microextraction and Chiral High-performance Liquid Chromatography

Here is reported a novel analytical approach for the extractive separation and determination of enantiomeric ratios of aristocularine in bovine serum albumin. The results demonstrate suitable analytical performances. The separation was performed by chiral high-performance liquid chromatography with a 5-µm column using a mobile phase of 1:1 n-hexane:ethanol at a flow rate of 0.7?mL?min^?1 with ultraviolet–visible absorption, circular dichroism, and polarimetric detection. The enantiomers were eluted at 13.2 and 15.6?min for (+) and (?)-aristocularine, with a resolution of 1.58 and a separation factor of 1.27. The analytical parameters for the dispersive liquid–liquid microextraction were optimized; under these conditions, the extraction recoveries were from 88.6% to 93.9% for a two-step extraction. The precision, reported as the percent relative standard deviation, had values from 2.9% to 3.2% for 0.5?µg?mL^?1 of analyte for five replicate measurements using ultraviolet–visible absorption and circular dichroism detection. The limits of detection were between 0.05 and 0.08?µg?mL^?1 with enrichment ratios up to a value of 12.     

Separation and Quantification of Key Starting Materials of Irbesartan Using Liquid Chromatography–Mass Spectrometry as a Separation and Identification Tool

Abstract

A liquid chromatography–mass spectrometry (LC-MS) method was developed and validated for determining the levels of 4-methyl-2-cyano biphenyl and 4-bromomethyl-2-cyano biphenyl, which are key starting materials of an antihypertensive drug substance, irbesartan. An active pharmaceutical ingredient of irbesartan was synthesized by using these two starting materials for its therapeutic use. We have explicated the LC-MS method to separate and quantify these two compounds in irbesartan at nanogram levels. The method was capable of separating irbesartan and its starting materials, which were monitored for their absence in the finished product of irbesartan. The separation was carried out at 40°C on a 150- × 4.6-mm cyano column by using the mobile phase containing 60 volumes of water adjusted to pH 3.2 with formic acid and 40 volumes of acetonitrile. The detection wavelength was 220 nm. The MS involved an electrospray ionization (ESI) probe and ion-trap analyzer and was validated with respect to its specificity, accuracy, and precision.     

Dynamic and Rheological Properties of Span 80 at Liquid–Liquid Interfaces

The adsorption characteristics of Span 80 at liquid/liquid interfaces were investigated. The equilibrium interfacial tension values were successfully fitted with a Langmuir isotherm resulting in the determination of a mean molecular area from 25 to 35 Å²/mol. The measured interfacial tension values and deduced adsorption parameters depend on the experimental technique used to obtain them, either Du Noüy ring or profile analysis tensiometry. Two possible explanations to such phenomenon are provided. Adsorption kinetics of Span 80 at liquid/liquid interfaces were studied, and it was concluded that the diffusion of Span 80 molecules from the bulk is the rate determining step of the adsorption. Finally the interfacial rheology properties were investigated and compared to the Lucassen–van den Tempel model. A good match was obtained when the isotherm parameters determined by profile analysis tensiometry were used.      

Absorption and Capture of Methane into Ionic Liquid

A reversible storage-release process switched by a temperature difference of 10℃around room temperature can be realized. This fast, recyclable, energy efficient, low cost and green system within a wide range of temperature and pressure is reported here for the first time. The system is believed to open up a new route for the storage and homogeneous utilization of methane.     

Liquid Chromatographic Determination of Glyoxal and Methylglyoxal from Serum of Diabetic Patients using Meso‐Stilbenediamine as Derivatizing Reagent

Abstract

Meso‐stilbenediamine has been used as derivatizing reagent for liquid chromatographic (LC) determination of glyoxal (Go), methylglyoxal (MGo), and dimethylglyoxal (DMGo) at pH 3. Liquid chromatographic elution and separation was carried out from the column Kromasil 100 C‐18, 5 µm (15×0.46 mm i.d.) with methanol: water:acetonitrile (59:40:1, v/v/v) with a flow rate of 1 mL/min and ultraviolet detection at 254 nm. The linear calibration curves were obtained for Go, MGo, and DMGo within 0.97–4.86 µg/mL, 1.52–7.6 µg/mL, and 1.41–7.08 µg/mL with detection limits of 48 ng/mL, 76 ng/mL, and 70.8 ng/mL, respectively. The method was applied for the determination of Go and MGo from serum of patients suffering from diabetes and ketosis. The amounts of Go and MGo found were 0.150–0.260 µg/mL and 0.160–0.270 µg/mL with coefficient of variation (C.V.) 2.6–4.7% and 2.5–4.6%, respectively. The results obtained were compared with normal subjects with Go and MGo contents of 0.025–0.065 µg/mL and 0.030–0.070 µg/mL with C.V 1.5–4.9% and 1.6–4.8% in the serum.     

A Dissipative Reaction Network Drives Transient Solid–Liquid and Liquid–Liquid Phase Cycling of Nanoparticles

Transient states maintained by energy dissipation are an essential feature of dynamic systems where structures and functions are regulated by fluxes of energy and matter through chemical reaction networks. Perfected in biology, chemically fueled dissipative networks incorporating nanoscale components allow the unique properties of nanomaterials to be bestowed with spatiotemporal adaptability and chemical responsiveness. We report the transient dispersion of gold nanoparticles in water, powered by dissipation of a chemical fuel. A dispersed state that is generated under non-equilibrium conditions permits fully reversible solid–liquid or liquid–liquid phase transfer. The molecular basis of the out-of-equilibrium process is reversible covalent modification of nanoparticle-bound ligands by a simple inorganic activator. Activator consumption by a coupled dissipative reaction network leads to autonomous cycling between phases. The out-of-equilibrium lifetime is tunable by adjusting the pH value, and reversible phase cycling is reproducible over several cycles.     

Ionic Liquid–Liquid Extraction and Supported Liquid Membrane Analysis of Lipophilic Wood Extractives from Dissolving-Grade Pulp

In this study, the extraction of lipophilic wood extractives from dissolving pulp samples using ionic liquid–liquid extraction and a two phase hollow fibre supported liquid membrane was investigated. Ionic liquids are capable of dissolving a range of organic and polymeric compounds and are biodegradable, with a negligible vapour pressure. Pulp samples were dissolved in a suitable amount of molten 1-butyl-3-methylimidazolium chloride to give 5 % cellulose solution. Pure cellulose was regenerated by adding water and filtered off. The ionic liquid-aqueous filtrate was first extracted for lipophilic extractives using liquid–liquid extraction. Then, a two phase hollow fibre supported liquid membrane extraction of lipophilic extractives was performed to extract the derivatized compounds prior to analysis by gas chromatography mass spectrometry. The operational parameters of this sample preparation approach were optimised using sterols and fatty acid methyl esters. The variation of enrichment factors and extraction efficiency with respect to liquid membrane, extraction time, stirring speed and sample pH were observed and used to get the optimal parameters. The approach was used in the analysis of oxygen bleached dissolving pulp samples in which main compounds identified were fatty acids, sterols, fatty alcohols, steroid hydrocarbons and ketones. These compounds were similar to those obtained using molecular solvent extraction method, which indicated the absence of chemical reaction between extractives and ionic liquid used.

     

Effect of a Nematic Liquid Crystalline Polymer as Highly Active β-Nucleator on Crystallization Structure and Morphology of Isotactic Polypropylene

The effects of nematic liquid crystalline polymer as a new β-nucleator (LCP-N) on crystallization structure and morphology of isotactic polypropylene (iPP) were investigated using wide-angle X-ray diffraction and polarized optical microscopy. The experimental results showed that LCP-N could lead to substantial changes in the crystallization structure and morphology of iPP. The nucleating activity of LCP-N mainly depended on its content, mesogenic molecules, and thermal history of processing. A high content of β-form (K _β) was obtained by the combined effect of the optimum LCP-N content and crystallization temperature. The maximum K _β reached 84% when the LCP-N content and crystallization temperature and time were 0.4 wt.%, 125°C, and 1 h, respectively. In addition, the birefringence of β spherulite was stronger than that of α spherulite; this difference is related to their particular way of growing and lamellar morphology. Due to its particular sheaf-like growth, the β spherulite was brighter and more colorful.     

Determination of Aflatoxins in Plant-based Milk and Dairy Products by Dispersive Liquid–Liquid Microextraction and High-performance Liquid Chromatography with Fluorescence Detection

The consumption of plant-based milk has increased due to their nutritional attributes. However, these products may contain aflatoxins if contaminated raw materials were used, although little concern is present in international regulation regarding this topic. In this work, dispersive liquid–liquid microextraction (DLLME) was used for the determination of the most important aflatoxins (B₁, B₂, G₁, and G₂) in oat, rice, coconut, almond, and birdseed plant-based milk and milk-based products enriched with oats, almonds, and walnuts using high-performance liquid chromatography (HPLC) with photochemical derivatization and fluorescence detection. Calibrations in matrix were performed for all of the samples, obtaining satisfactory linearity, with correlation coefficients exceeding 0.994 for all of the aflatoxins. The precision in terms of repeatability and intermediate precision, expressed as the relative standard deviation, was lower than 9.7%, and recoveries ranged between 82 and 104%, fulfilling current legislation for the determination of aflatoxins. In addition, the limits of quantification were 0.5?µg?L^?1 for the aflatoxins, allowing the determination of these compounds below the maximum levels established by European Commission in these commodities. Finally, 23 commercial products were analyzed to characterize the presence of these toxins.     

Synthesis and Characterization of New UV-curable Liquid Crystalline Diacrylates

A series of UV-curable liquid crystalline diacrylates were synthesized by using 4, 4‘-(terephthaloyldioxy) dibenzoic acid as a mesogen unit.     

O/W Emulsions with Liquid Crystals as Vehicles of β-Escin

Aescin is an important active substance composed of saponin glucosides topical employed in the treatment of inflammatory and edematous conditions. A particular kind of skin care product called α-gel lamellar phases emulsion was developed, containing β-escin. Detailed knowledge of the lamellar phases behavior has been obtained by DSC, rheological measurements and polarized-light optical microscopy. Moreover the effects of lamellar phases on β-escin release profiles have been studied.     

Synthesis of a New Liquid Crystalline Polymer as a Highly Active β-Nucleator and Its Effect on Melting and Crystallization Behaviors of Isotactic Polypropylene

A new nematic liquid crystalline polymer as a highly active β-nucleator (LCP-N) of isotactic polypropylene (iPP) was synthesized and characterized. The effect of LCP-N on thermal behavior of the iPP was investigated with differential scanning calorimetry. LCP-N showed a melting transition at 85.0°C and a nematic to isotropic phase transition at 278.0°C. The incorporation of LCP-N could lead to substantial changes in the thermal behavior of the iPP. The nucleating activity of LCP-N mainly depended on its content, mesogenic molecular structure, and thermal history of processing. A high content of β-form could be obtained by the combined effect of the optimum LCP-N concentration and crystallization temperature and time. The Φ_β reached 77% when the LCP-N content, crystallization temperature, and crystallization time were 0.4 wt.%, 125°C, and 1 h, respectively.     

Determination of Phthalate Esters in Wine Using Dispersive Liquid–Liquid Microextraction and Gas Chromatography

A simple and rapid efficient method was developed for the determination of phthalate esters using dispersive liquid–liquid microextraction followed by gas chromatography with flame ionization detection. A mixture of isopropanol (0.75 mL, dispersant) and carbon tetrachloride (30 µL, extractant) with sodium chloride (1%, w/v) was used for extraction. Under optimum conditions, the method provided linear calibration curves between 0.5 and 200 µg L^?1 for dibutyl phthalate, and 1.0 and 200 µg L^?1 for butyl benzyl phthalate, diethyl phthalate, and diisooctyl phthalate. The relative standard deviations for intra-day and inter-day analyses were less than 5.8% and 6.9%, respectively, with enrichment factors between 229 and 424. Two wine samples were analyzed with recoveries between 70.1% and 119.3%.     

Chromatographic and Spectroscopic Studies on β-Cyclodextrin Functionalized Ionic Liquid as Chiral Stationary Phase: Enantioseparation of Flavonoids

In this study, β-cyclodextrin functionalized ionic liquid was prepared by adding 1-benzylimidazole onto 6-monotosyl-6-deoxy-β-cyclodextrin (β-CDOTs) to obtain β-CD-BIMOTs. β-CD-BIMOTs were then bonded onto the modified silica to produce chiral stationary phases (β-CD-BIMOTs-CSP). The performance of β-CD-BIMOTs-CSP was evaluated by observing the enantioseparation of flavonoids. The performance of β-CD-BIMOTs stationary phase was also compared with native β-CD stationary phase. For the selected flavonoids, flavanone and hesperetin obtained a high resolution factor in reverse phase mode. Meanwhile, naringenin and eriodictyol attained partial enantioseparation in polar organic mode. In order to understand the mechanism of separation, the interaction of selected flavonoids and β-CD-BIMOTs was studied using spectroscopic methods (¹H NMR, NOESY and UV–Vis spectrophotometry). The enantioseparated flavanone and hesperetin were found to form an inclusion complex with β-CD-BIMOTs. However, naringenin and eriodictyol were not enantioseparated due to the formation of hydrogen bonding at exterior torus of β-CD-BIMOTs.

     

Magnetic Solid-Phase Extraction and Ionic Liquid Dispersive Liquid–Liquid Microextraction Coupled with High-Performance Liquid Chromatography for the Determination of Hexachlorophene in Cosmetics

An efficient, simple, and fast method based on ionic liquid dispersive liquid–liquid microextraction (IL-DLLME) followed by magnetic solid-phase extraction (MSPE) was developed as a new technique for extracting and purifying hexachlorophene (HCP) in cosmetics prior to high-performance liquid chromatography (HPLC) determination. In this method based on IL-DLLME and MSPE, 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) is used as the extraction solvent and Fe₃O₄ nanoparticles are used to remove hydrophobic additives in the cosmetics by physical adsorption. The main parameters affecting the efficiency of the IL-DLLME and MSPE of HCP were investigated and optimized. Under the optimum conditions, the method was linear in the range 0.5–40 µg mL^?1 with a correlation coefficient (R ²) of 0.9976 and had a detection limit of 0.14 µg mL^?1 at a signal-to-noise ratio (S/N) of 3. The recoveries of HCP in three cosmetic samples using the proposed method were in the range 74.5–97.7%, and the relative standard deviations (RSD, n = 5) were in the range 3.8–6.7%. The developed method was successfully applied to the determination of HCP in cosmetics.