Microwave-assisted extraction combined with dispersive liquid-liquid microextraction as a new approach to determination of chlorophenols in soil and sediments

A new method was applied for extraction of five chlorophenols from soil and marine sediment samples. Microwave-assisted extraction coupled with dispersive liquid-liquid microextraction followed by semi-automated in-syringe back-extraction technique was used as an extraction technique. Microwave-assisted extraction was performed by using 2.0 mL of alkaline water at pH 10.0. After extraction, the pH of extraction solution was adjusted at 6.0 and dispersive liquid-liquid microextraction procedure was done using 1.0 mL of acetone as a disperser solvent and 37.0 μL of chlorobenzene as extraction solvent. About 20.0 ± 0.5 μL sedimented phase was collected after centrifugation step. Then, chlorophenols were back extracted into 20 μL of alkaline water at pH 12.0 within the microsyringe. Finally, 20.0 μL of aqueous solution was injected into high performance liquid chromatography with ultra violet detection for analysis. The obtained recovery and preconcentration factors for the analytes were in the range of 68.0-82.0% and 25-30, respectively, with relative standard deviations ≤7.6%. The limits of the detection were found in the range of 0.0005-0.002 mg/kg. The method provides a simple and fast procedure for the extraction and determination of chlorophenols in soil and marine sediment samples.     

Determination of phenols in waters by stir membrane liquid-liquid-liquid microextraction coupled to liquid chromatography with ultraviolet detection

A simple and rapid method for the determination of eleven phenols in water samples is presented. The target analytes are isolated by stir membrane liquid-liquid microextraction working under the three-phase mode. An alkaline aqueous solution is used as extractant phase while octanol is selected as supported liquid membrane solvent. The target analytes are separated and determined by liquid chromatography (LC) with ultraviolet detection (UV). All the variables involved in the extraction process have been studied in depth. Low detection limits (in the range from 82.1 ng/L for phenol to 452 ng/L for 2,4,5-trichlorophenol) were obtained. The repeatability, expressed as relative standard deviation (RSD), varied between 1.3% (for 4-nitrophenol) and 8.0% (for 4-chlorophenol). The enrichment factors were in the range from 168 (for 2,4,5-trichlorophenol) to 395 (for 3-chlorophenol). The proposed procedure was applied for the direct determination of the eleven phenols in some real water samples including river, well and tap waters. The accuracy was evaluated by means of a recovery study, the results being in the range of 87-120%.     

pH‐assisted homogeneous liquid–liquid microextraction using dialkylphosphoric acid as an extraction solvent for the determination of chlorophenols in water samples

In this study, a new pH‐assisted homogeneous liquid–liquid microextraction combined with HPLC with UV detection was developed for the determination of chlorophenols in water samples. In this approach, bis(2‐ethylhexyl) phosphate was used for the first time as the low‐density extraction solvent. In particular, 60 μL of bis(2‐ethylhexyl) phosphate was injected into the sample solution (5 mL) and dissolved completely in the sample solution while the pH was increased to 9. Afterwards, the pH of the sample solution was lowered to 1, and a cloudy solution was formed. At this stage, hydrophobic interactions between the analytes and the long double hydrocarbon chains of extraction solvent were expected to be the main forces driving extraction. A series of parameters that influence extraction were investigated systematically. Under the optimized conditions, the LODs and LOQs for the chlorophenols were 1.4–2.7 and 4.7–9.1 ng/mL, respectively. RSDs based on five replicate extraction of 100 ng/mL of each chlorophenols were <4.7% for intraday and 7.4% for interday precision. This method has been also successfully applied to analyze real water samples at two different spiked concentrations, and satisfactory recoveries were achieved.     

Comparison and application of two microextractions based on syringe membrane filter

Two proposed syringe membrane filter solid phase microextraction and syringe membrane filter liquid/solid phase microextraction, coupled separately with high performance liquid chromatography, were developed for simultaneous enrichment and determination of the trace level of flavonoids in traditional Chinese medicine. In syringe membrane filter solid phase microextraction, the membrane of syringe membrane filter was served as a solid adsorption film to adsorb target analytes. And in syringe membrane filter liquid/solid phase microextraction, the membrane of syringe membrane filter was used as not only an adsorption phase, but also as a holder of extraction solvent to realize liquid‐solid synergistic extraction. The simple operation, rapid extraction, and little or no organic solvent consumption make the two approaches very interesting. To evaluate the two proposed approaches, the crucial parameters affecting the enrichment factors of target analytes were investigated and optimized, and the two microextractions were intercompared. Moreover, their microextraction mechanisms were analyzed and described. Under the optimized conditions, both the new approaches achieved good linearities, accuracies, precisions, and low limits of detection, and the two methods were successfully applied for concentration of the flavonoids in traditional Chinese medicines.     

Determination of pesticides in water by cone-shaped membrane protected liquid phase microextraction prior to micro-liquid chromatography

A new sample pre-treatment technique termed cone-shaped membrane liquid phase microextraction (CSM-LPME) was developed and combined with micro-liquid chromatography (micro-LC) for the determination of selected pesticides in water samples. Four pesticides (hexaconazole, procymidone, quinalphos and vinclozolin) were considered as target analytes. Several important extraction parameters such as types of extraction solvent, agitation rate, pH value, total exposure time and effect of salt and humic acids were optimized. Enrichment factors of > 50 folds were easily achieved within 20 min of extraction. The analytical data demonstrated relative standard deviations for the reproducibility of the optimized CSM-LPME method ranging from 6.3 to 7.5%. The correlation coefficients of the calibration curves were at least 0.9995 across a concentration range of 2-100 microg/L. The detection limits for all the analytes were found to be in the range of 1.1-1.9 microg/L.     

Hollow‐fiber solvent bar microextraction with gas chromatography and electron capture detection determination of disinfection byproducts in water samples

A liquid‐phase microextraction method that uses a hollow‐fiber solvent bar microextraction technique was developed by combining gas chromatography with electron capture detection for the analysis of four trihalomethanes (chloroform, dichlorobromomethane, chlorodibromomethane, and bromoform) in drinking water. In the microextraction process, 1‐octanol was used as the solvent. The technique operates in a two‐phase mode with a 5 min extraction time, a 700 rpm stirring speed, a 30°C extraction temperature, and NaCl concentration of 20%. After microextraction, one edge of the membrane was cut, and 1 μL of solvent was collected from the membrane using a 10 μL syringe. The solvent sample was directly injected into the gas chromatograph. The analytical characteristics of the developed method were as follows: detection limits, 0.017–0.037 ng mL⁻¹; linear working range, 10–900 ng mL⁻¹; recovery, 74 ± 9–91 ± 2; relative standard deviation, 5.7–10.3; and enrichment factor, 330–455. A simple, fast, economic, selective, and efficient method with big possibilities for automation was developed with a potential use to apply with other matrices and analytes.     

Determination of chlorophenols in water using dispersive liquid–liquid microextraction coupled with water‐in‐oil microemulsion electrokinetic chromatography in normal stacking mode

The current routes to couple dispersive liquid–liquid microextraction with capillary electrophoresis are the evaporation of water immiscible extractants and the back‐extraction of analytes. In this study, a new methodology for this combination using water‐in‐oil microemulsion electrokinetic chromatography coupled with normal stacking mode on‐line sample concentration was developed to analyze chlorophenols in water samples. The analytes were extracted with tributyl phosphate and the extractant dilution (3×) was directly injected into an electrophoresis buffer (7.7 cm) containing 5% sodium dodecyl sulfate, 78% 1‐butanol, 2% 1‐heptane, and 15% sodium acetate solution (pH 8.0). This proposed method is very simple and convenient compared to the conventional procedures. The key parameters affecting separation and concentration were systematically optimized. Under the optimized conditions, dispersive liquid–liquid microextraction contributed an enrichment factor of 45–50, and the overall sensitivity improvement was 312–418‐fold. Limits of detection between 1.4 and 3.0 ng/mL and limits of quantification between 4.5 and 10.2 ng/mL were achieved. Acceptable repeatability lower than 3.0% for migration time and 9.0% for peak areas were obtained. The developed method was successfully applied for analysis of the chlorophenols in real water samples.     

Fabrication of a novel hydrophobic/ion‐exchange mixed‐mode adsorbent for the dispersive solid‐phase extraction of chlorophenols from environmental water samples

A novel mixed‐mode adsorbent was prepared by functionalizing silica with tris(2‐aminoethyl)amine and 3‐phenoxybenzaldehyde as the main mixed‐mode scaffold due to the presence of the plentiful amino groups and benzene rings in their molecules. The adsorption mechanism was probed with acidic, natural and basic compounds, and the mixed hydrophobic and ion‐exchange interactions were found to be responsible for the adsorption of analytes. The suitability of dispersive solid‐phase extraction was demonstrated in the determination of chlorophenols in environmental water. Several parameters, including sample pH, desorption solvent, ionic strength, adsorbent dose, and extraction time were optimized. Under the optimal extraction conditions, the proposed dispersive solid‐phase extraction coupled with high‐performance liquid chromatography showed good linearity range and acceptable limits of detection (0.22∽0.54 ng/mL) for five chlorophenols. Notably, the higher extraction recoveries (88.7∽109.7%) for five chlorophenols were obtained with smaller adsorbent dose (10 mg) and shorter extraction time (15 min) compared with the reported methods. The proposed method might be potentially applied in the determination of trace chlorophenols in real water samples.     

Application of tandem dispersive liquid–liquid microextraction for the determination of doxepin,citalopram, and fluvoxamine in complicated samples

A new type of dispersive liquid–liquid microextraction is used for the determination of doxepin, citalopram, and fluvoxamine in aqueous matrices. This method is based upon the tandem utilization of dispersive liquid–liquid microextraction, and by providing a high sample clean‐up, it efficiently improves the applicability of the method in complicated matrices. For this purpose, in the first step, the analytes contained in an aqueous sample solution (8.0 mL) were extracted into an organic solvent, and then these analytes were simply back‐extracted into an aqueous acceptor phase (50 μL). The overall extraction time was 7 min, and very simple tools were required for this aim. Optimization of the variables affecting the method such as the type and volume of the organic solvent used and effect of ionic strength was carried out to achieve the best extraction efficiency. Under the optimized experimental conditions, tandem dispersive liquid–liquid microextraction with high‐performance liquid chromatography and UV detection showed a good linearity in the range of 10–5000 ng/mL. The limits of detection were in the range of 3–10 ng/mL. The Intra‐day precisions (relative standard deviation) were 9.2, 4.5, and 4.8, and the recoveries were 58.5, 52.9, and 39.3% for citalopram, doxepin, and fluvoxamine, respectively.     

Solid‐based disperser liquid–liquid microextraction for the preconcentration of phthalate esters and di‐(2‐ethylhexyl) adipate followed by gas chromatography with flame ionization detection or mass spectrometry

A new approach for the development of a dispersive liquid–liquid microextraction followed by GC with flame ionization detection was proposed for the determination of phthalate esters and di‐(2‐ethylhexyl) adipate in aqueous samples. In the proposed method, solid and liquid phases were used as the disperser and extractant, respectively, providing a simple and fast mode for the extraction of the analytes into a small volume of an organic solvent. In this method, microliter levels of an extraction solvent was added onto a sugar cube and it was transferred into the aqueous phase containing the analytes. By manual shaking, the sugar was dissolved and the extractant was released into the aqueous phase as very tiny droplets to provide a cloudy solution. Under optimized conditions, the proposed method showed good precision (RSD less than 5.2%), high enrichment factors (266–556), and low LODs (0.09–0.25 μg/L). The method was successfully applied for the determination of the target analytes in different samples, and good recoveries (71–103%) were achieved for the spiked samples. No need for a disperser solvent and higher enrichment factors compared with conventional dispersive liquid–liquid microextraction and low cost and short sample preparation time are other advantages of the method.     

Poly(vinylidene fluoride) membrane based thin film microextraction for enrichment of benzoylurea insecticides from water samples followed by their determination with HPLC

Thin-film microextraction(TFME),a new geometry for solid-phase microextraction,has become an attractive sample-preparation technique.Compared to other microextraction approaches,the sensitivity of this technique was enhanced without sacrificing the sampling time due to the high surface area-tovolume ratio together with the increase of extraction-phase volume.In this paper,a new TFME method based on poly(vinylidene fluoride) membrane was developed for the extraction of benzoylurea insecticides(diflubenzuron,triflumuron,hexaflumuron and teflubenzuron) from water samples followed by their determination with high performance liquid chromatography-diode array detection.Under the optimal conditions,good linearity was observed over the concentration range of 0.5-100.0 ng/mL with correlation coefficient greater than 0.9994.The limits of detection(S/N = 3) of the method for the target analytes were 0.1 ng/mL.Mean recoveries ranged from 87.7% to 103.9% with relative standard deviations lower than 6.5%.The results indicated that the developed TFME method is simple,efficient,and cost effective.     

Application of liquid-liquid-liquid microextraction and ion-pair liquid chromatography coupled with photodiode array detection for the determination of chlorophenols in water

A method termed as liquid-liquid-liquid microextraction was utilized to extract chlorophenols from water. The extracted chlorophenols, present in anionic form, were then separated, identified, and quantitated by ion-pair high-performance liquid chromatography with photodiode array detection (HPLC/DAD). For trace chlorophenol determination using HPLC/DAD, the chlorophenolate anion provides a better ultraviolet spectrum for quantitative and qualitative analyses than does uncharged chlorophenol. This is due to the auxochromic effect of the phenolate anion. In the study, experimental conditions such as organic phase identity, acceptor phase volume, sample agitation, extraction time, acceptor phase NaOH concentration, donor phase HCl concentration, salt addition, and UV absorption wavelength were optimized. Relative standard deviations (RSD, 2.3-5.4%), coefficients of determination (r2 0.9994-0.9999), and detection limits (0.049-0.081 ng mL(-1)) of the proposed method were investigated under the selected conditions. The method was successfully applied to analyses of reservoir and tap water samples, and the relative recoveries of chlorophenols from the spiked reservoir and tap water samples were 94.1-100.4% and 87.8-101.2%, respectively. The proposed method is capable of identifying and quantitating each analyte to 0.5 ng mL(-1), confirming the HPLC/DAD technique to be quite robust for monitoring trace levels of chlorophenols in water samples.     

Application of fabric phase sorptive extraction with gas chromatography and mass spectrometry for the determination of organophosphorus pesticides in selected vegetable samples

In the present work, a high‐efficiency and solvent minimized microextraction technique, fabric phase sorptive extraction followed by gas chromatography and mass spectrometry analysis is proposed for the rapid determination of four organophosphorus pesticides (terbufos, malathion, chlorpyrifos, and triazofos) in vegetable samples including beans, tomato, brinjal, and cabbage. Fabric phase sorptive extraction combines the beneficial features of sol‐gel derived microextraction sorbents with the rich surface chemistry of cellulose fabric substrate, which collectively form a highly efficient microextraction system. Fabric phase sorptive extraction membrane, when immersed directly into the sample matrix, may extract target analytes even when high percentage of matrix interferents are present. The technique also greatly simplifies sample preparation workflow. Most important fabric phase sorptive extraction parameters were investigated and optimized. The developed method displayed good linearity over the concentration range 0.5–500 ng/g. Under optimum experimental conditions, the limits of detection were found in the range of 0.033 to 0.136 ng/g. The relative standard deviations for the extraction of organophosphorus pesticides were < 5%. Subsequently, the new method was applied to beans, tomato, brinjal, and cabbage samples. The results from the real sample analysis indicate that the method is green, rapid, and economically feasible for the determination of organophosphorus pesticides in vegetable samples.     

Determination of Diuretics in Urine Using Immobilized Multi‐Walled Carbon Nanotubes in Hollow Fiber Liquid‐Phase Microextraction Combined with Liquid Chromatography‐Tandem Mass Spectrometry

A novel technique utilizing the adsorptive potential of immobilized multi‐walled carbon nanotubes (I‐MWCNT) in hollow fiber liquid‐phase microextraction (HF‐LPME) was developed for the determination of diuretics in urine. In this study, the potential of carbon nanotubes as a sorbent for three‐phase liquid‐phase microextraction of diuretics from urine samples was evaluated. Analysis was performed using liquid chromatography‐tandem mass spectrometry (LC‐MS/MS). A novel method was applied to detect acetazolamide (AAA), chlorothiazide (CTA), hydrochlorothiazide (HCT), hydroflumethiazide (HFT), clopamide (CA), trichlormethiazide (TCM), althiazide (AT) and bendroflumethiazide (BFT) in urine. Two‐step extractions using different times and temperatures for each step were adopted. Parameters influencing the extraction efficiency, including the extraction solvent, sample pH, salt concentration, extraction time and extraction temperature were systematically optimized. Under the resulting optimal extraction conditions, this method showed good linearity over an analytes concentration range of 1 to 1000 ng/mL, high extraction repeatability with relative standard deviations of less than 6%, and low detection limits (0.09 to 0.51 ng/mL). The application of the methods to the determination of diuretics in real samples was tested by analyzing urine samples of patient.     

Determination of non-steroidal anti-inflammatory drugs in urine by the combination of stir membrane liquid–liquid–liquid microextraction and liquid chromatography

A stir membrane liquid phase microextraction procedure working under the three-phase mode is proposed for the first time for the determination of six anti-inflammatory drugs in human urine. The target compounds are isolated and preconcentrated using a special device that integrates the extractant and the stirring element. An alkaline aqueous solution is used as extractant phase while 1-octanol is selected as supported liquid membrane solvent. After the extraction, all the analytes are determined by liquid chromatography (LC) with ultraviolet detection (UV). The analytical method is optimized considering the main involved variables (e.g., pH of donor and acceptor phases, extraction time, stirring rate) and the results indicate that the determination of anti-inflammatory drugs at therapeutic and toxic levels is completely feasible. The limits of detection are in the range from 12.6 (indomethacin) to 30.7 μg/L (naproxen). The repeatability of the method, expressed as relative standard deviation (RSD, n = 5) varies between 3.4% (flurbiprofen) and 5.7% (ketoprofen), while the enrichment factors are in the range from 35.0 (naproxen) to 72.5 (indomethacin).     

Ultrapreconcentration and determination of organophosphorus pesticides in water by solid‐phase extraction combined with dispersive liquid–liquid microextraction and high‐performance liquid chromatography

Solid‐phase extraction coupled with dispersive liquid–liquid microextraction was developed as an ultra‐preconcentration method for the determination of four organophosphorus pesticides (isocarbophos, parathion‐methyl, triazophos and fenitrothion) in water samples. The analytes considered in this study were rapidly extracted and concentrated from large volumes of aqueous solutions (100 mL) by solid‐phase extraction coupled with dispersive liquid–liquid microextraction and then analyzed using high performance liquid chromatography. Experimental variables including type and volume of elution solvent, volume and flow rate of sample solution, salt concentration, type and volume of extraction solvent and sample solution pH were investigated for the solid‐phase extraction coupled with dispersive liquid–liquid microextraction with these analytes, and the best results were obtained using methanol as eluent and ethylene chloride as extraction solvent. Under the optimal conditions, an exhaustive extraction for four analytes (recoveries >86.9%) and high enrichment factors were attained. The limits of detection were between 0.021 and 0.15 μg/L. The relative standard deviations for 0.5 μg/L of the pesticides in water were in the range of 1.9–6.8% (n = 5). The proposed strategy offered the advantages of simple operation, high enrichment factor and sensitivity and was successfully applied to the determination of four organophosphorus pesticides in water samples.     

Direct determination of chlorophenols present in liquid samples by using a supported liquid membrane coupled in-line with capillary electrophoresis equipment

Actually there is a great trend on the development of effective analytical methods for monitoring trace levels of various phenols which can indicate, among others compounds, the water quality. A simple, inexpensive supported liquid membrane (SLM) device was used in combination with commercially available capillary electrophoresis (CE) equipment for the direct determination of chlorophenols in surface water samples. The manifold was used simultaneously to extract and preconcentrate the analytes from liquid samples. In the extraction set-up, the donor phase (4 mL) was placed in the CE vial, where a micro-membrane extraction unit (MMEU) accommodating the acceptor phase (100 μL) in its lumen was immersed. The supported liquid membrane was constructed by impregnating a porous Fluoropore Teflon (PTFE) membrane with a water-immiscible organic solvent (dihexyl ether). The extraction process was optimized with regard to the pH of the donor and acceptor phases, membrane liquid, extraction time and voltage applied to the inlet or outlet vial during extraction. The chlorinated phenols pentachlorophenol (PCP), 2,3,6 trichlorophenol (TCP) and 2,6 dichlorophenol (DCP) were thus efficiently separated by CE, using tris(hydroxymethyl)aminomethane (Tris) and an NaH₂PO₄ solution containing 1% (v/v) methanol at pH 10.5 as running buffer.     

Determination of chlorophenols in landfill leachate using headspace sampling with ionic liquid-coated solid-phase microextraction fibers combined with gas chromatography–mass spectrometry

A new microextraction technique based on ionic liquid solid-phase microextraction (IL-SPME) was developed for determination of trace chlorophenols (CPs) in landfill leachate. The synthesized ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄MIM][PF₆]), was coated onto the spent fiber of SPME for extraction of trace CPs. After extraction, the absorbed analytes were desorbed and quantified using gas chromatography–mass spectrometry (GC/MS). The term of the proposed method is as ionic liquid-coated of solid-phase microextraction combined with gas chromatography–mass spectrometry (IL-SPME-GC/MS). No carryover effect was found, and every laboratory-made ionic liquids-coated-fiber could be used for extraction at least eighty times without degradation of efficiency. The chlorophenols studied were 2,4-dichlorophenol (2,4-DP), 2,4,6-trichlorophenol (2,4,6-TCP), 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP), and pentachlorophenol (PCP). The best results of chlorophenols analysis were obtained with landfill leachate at pH 2, headspace extraction for 4 min, and thermal desorption with the gas chromatograph injector at 240 °C for 4 min. Linearity was observed from 0.1 to 1000 μg L⁻¹ with relative standard deviations (RSD) less than 7% and recoveries were over 87%. The limit of detection (LOD) for pentachlorophenol was 0.008 μg L⁻¹. The proposed method was tested by analyzing landfill leachate from a sewage farm. The concentrations of chlorophenols were detected to range from 1.1 to 1.4 μg L⁻¹. The results demonstrate that the IL-SPME-GC/MS method is highly effective in analyzing trace chlorophenols in landfill leachate.     

Determination of acidic drugs in biological and environmental matrices by membrane‐based dual emulsification liquid‐phase microextraction followed by high‐performance liquid chromatography

A simple method is introduced providing a highly clean microextraction for the determination of some anti‐inflammatory drugs as the model analytes in human urine and environmental matrices. This method is based upon the implementation of two consecutive emulsification liquid‐phase microextractions, which are separated by a syringe filtration step. In this method, the organic extraction solvent (dihexyl ether) is dispersed into the aqueous sample solution (20 mL), and the resulting cloudy mixture is passed through a hydrophilic polytetrafluoroethylene syringe filter. By this action, the extraction phase containing the analytes and many interfering species that could be transferred into the organic phase is retained behind the hydrophilic membrane. The filter is then detached from the syringe and attached to another syringe containing an aqueous solution (pH 12.0, 150 μL), and by the in‐syringe dispersion of the organic phase into the aqueous phase, the analytes are selectively back‐extracted into the aqueous phase. The developed method is centrifuge‐free and very simple, and provides a high sample clean‐up in a few minutes. Under the optimized experimental conditions, the developed method provided a linearity in the range of 2.0–2000 ng/mL, a low limit of detection (0.5 ng/mL), and enrichment factors of 47–53.     

Headspace solid phase micro extraction GC-ECD determination of volatile organic chlorinated hydrocarbons in soils

Soil samples were suspended in a suitable aqueous solvent and a solid phase microextraction (SPME) fibre was used to sample the headspace (HS) for five volatile chlorinated compounds (VOX). Their determination was made by GC-ECD technique in the splitless mode. Preliminary studies on the effects of methanol and of the sand/clay ratio on the fibre extraction were made. Four experimental factors, namely, extraction time, extraction temperature, pH and NaCl%, able to affect distribution of the analytes among the four different phases, were varied in suitable ranges. A multivariate approach applied to the face centred cube (FCC) experimental design, was used to try to optimise the overall sample response. The suitable set of factors found for the determination of chloroform, 1,2-dichloroethane, trichloroethylene, 1,1 ,2-trichloroethane, 1,1,2,2-tetrachloroethane, was a compromise among the relevant optimal factor sets of the single analytes. Detection limits of 0.003 ng, 0.022 ng, 0.001 ng, 0.015 ng and 0.002 ng were found respectively for the five cited analytes. The method was successfully used to determine the analyte contents in two real soils sampled in an industrial area.