Germanium dioxide as internal standard for simplified trace determination of bromate, bromide, iodate and iodide by on-line coupling ion chromatography-inductively coupled plasma mass spectrometry

The use of elemental mass spectrometry as detection for ion chromatography allows sensitive determination of several bromine and iodine species at a reasonable time scale. Lowest concentrations observable are 66 ng L(-1) for bromate, 45 ng L(-1) for iodate, 74 ng L(-1) for bromide and 151 ng L(-1) for iodide. A major drawback of previous IC-ICP-MS applications is the high consumption of time and thus the running costs. The use of GeO2 as internal standard not only allows improved external calibration, but also semiquantitative determination of bromate, bromide, iodate and iodide without any calibration procedure. Furthermore, GeO2 can be used for all known types of anion exchange columns regardless of their construction principles. It is shown, that the analyte-to-GeO2 ratio of four bromine and iodine species was nearly constant over 4 months and almost independent from the ICP-MS instrumental settings. The quantification by means of the analyte-to-GeO2 ratio for samples taken from a bromate round robin test shows that the values obtained are in excellent agreement with calibration curve and isotope dilution results.     

离子色谱-紫外检测法同时分析碘酸根、碘离子、溴酸根和溴离子

建立了同时分析碘酸根、碘离子、溴酸根和溴离子的离子色谱-紫外检测分析方法。用季铵型阴离子交换柱,以柠檬酸-乙腈为流动相,采用紫外检测器实现了4种离子的同时分离和检测。研究了检测波长和流动相种类、浓度、pH值等因素对4种离子分离和测定的影响,探讨了保留规律,优化了色谱分析条件。在检测波长为210 nm、流动相为1.0 mmol/L柠檬酸-乙腈（85：15,v/v;pH 5.0）、流速为0.9 mL/min、柱温为40 ℃条件下,4种离子完全分离,且系统峰不干扰测定。4种离子的检出限（S/N=3）为0.07~0.16 mg/L,连续5次进样测定的峰面积和保留时间的相对标准偏差均在1%以下。将此方法用于离子液体样品及地下水样品的分析,结果准确、可靠。     

Separation of bromide, bromate, iodide, iodate, nitrite, nitrate and selenite anions by capillary zone electrophoresis

Summary Capillary zone electrophoresis (CZE) has been used for the separation of bromide, bromate, iodide, iodate, nitrite, nitrate and selenite anions. The separation was achieved using a fused silica capillary (72 cm long x 50 m i.d.) filled with an acidic phosphate buffer (pH=3, 25 mmol/l), and with on-column UV detection at 200 nm. The influence of different experimental parameters such as pH, ionic strength and voltage, was studied. The nitrate concentration of a Rhine water sample was then determined under selected conditions and the results were compared to those obtained by high performance ion chromatography (HPIC).On leave from the Universitat de Barcelona (postdoctoral fellowship from ECC-BCR).     

Spectrophotometric determination of periodate, iodate and bromate mixtures based on their reaction with iodide.

A rapid, simple, precise and accurate method is proposed for the determination of ternary mixtures of periodate-iodate-bromate based on their reaction with iodide ion at different pH values. The absorbance was measured at 352 nm. Three sets of reaction conditions were developed. In the first set of conditions, only periodate reacted with iodide, but in the second set the periodate and iodate reacted with iodide and in the third set the three ions reacted with iodide during the first 3 min after initiation of the reaction. The method could be used for individual determinations of periodate, iodate and bromate in the concentration range of 0.05-8.0 microg/ml, 0.05-5.0 microg/ml and 0.2-12 microg/ml, respectively. The data were evaluated by simultaneous equations.     

Comparative study of the vicinal functionalization of olefins with 2:1 bromide/bromate and iodide/iodate reagents

A comparative evaluation was made on the syntheses of vicinal halohydrins, halo methyl ethers, and halo acetates from olefins using 2:1 Br⁻/BrO₃⁻ and I⁻/IO₃⁻ reagents. In many cases both reagents afforded products selectively in high yields. The highest halogen atom efficiencies attained were 97% and 93% for Br⁻/BrO₃⁻ and I⁻/IO₃⁻, respectively. Of the two reagents, I⁻/IO₃⁻ was established to be the preferred reagent for vicinal functionalization of linear alkenes and also for halo acetate preparation. However, only Br⁻/BrO₃⁻ was effective for vicinal functionalization of trans-stilbene and chalcones.     

Kinetic study of the iodate—iodide and chlorate—iodide reactions in acidic solutions,and a method for the microdetermination of bromide

The iodate—iodide and chlorate—iodide reactions were studied spectrophotometrically in acidic solutions by stopped-flow techniques. Intermediate products(I⁺)were followed; reaction rate constants and activation energies of the reactions were determined. A method of determining bromide was developed on the basis of its accelerating effect on the iodate—iodide reaction ; microamounts of bromide in the range 16–320 μg (10^-4–2 × 10^-3M) were determined with relative errors and relative standard deviation of about 2%.bl]     

Screening for sarin in air and water by solid-phase microextraction-gas chromatography-mass spectrometry.

A method of screening air and water samples for the chemical-warfare agent Sarin is developed using solid-phase microextraction (SPME)-gas chromatography (GC)-mass spectrometry (MS). The SPME field kit sampler is ideal for collecting air and water samples in the field and transporting samples safely to the laboratory. The sampler also allows the sample to be introduced into the GC-MS system without further sample preparation. Results of the tests with Sarin using the SPME technique indicate that a sample collection time of 5 min is sufficient to detect 100 ng/L of Sarin in air. For water samples, Sarin is detected at a concentration of 12 microg/mL or higher. This method is ideal for screening samples for quick response situations.     

Ion chromatographic determination of trace iodate, chlorite, chlorate, bromide, bromate and nitrite in drinking water using suppressed conductivity detection and visible detection

An ion chromatography method for the simultaneous determination of trace iodate, chlorite, chlorate, bromide, bromate and nitrite in drinking water has been developed using an anion-exchange column and the suppressed conductivity detector, followed by post-column addition of reagent to enhance visible absorbance detection of ions. A high capacity anion exchange Ion Pac9-HC column (250 mm x 4 mm I.D.) was used. Eight millimole per liter sodium carbonate was used as eluent, an auto-suppression external water mode was selected, 0.5 g/l o-dianisidine.2HCl (ODA)+4.5 g/l KBr+25% methanel+5.6% nitric acid was used as post-column reagent. The post-column reaction (PCR) temperature was at 60 degrees C, and the visible absorbance detected wavelength at 450 nm. The sample's pH and coexist anions had no influence on determination. The method enjoyed a wide linear range and a good linear correlation coefficient (r>0.999). The method detection limits were between 0.023 and 2.0 microg/l. The average recoveries ranged from 87.5 to 110.0%, and the relative standard deviations (RSD) were in the range of 1.1-4.6%. The analytical results by the method of post-column addition of reagent to enhance visible absorbance detection of anions was compared with that of the suppressed conductivity detection, and the former was proved to be better in sensitivity and selectivity. The results showed that this method was accurate, sensitive and might be good for application and suitable for trace analysis at the level of mug/l.     

On the determination of cerium(IV) by iodate and bromate

Analytical and Bioanalytical Chemistry - Determination of cerium(IV), based upon its reduction by a measured excess of KSCN solution and titration of the excess against standard iodate or bromate,...     

Full automation of derivatization--solid-phase microextraction-gas chromatography-mass spectrometry with a dual-arm system for the determination of organometallic compounds in aqueous samples

The determination of organometallic compounds in aqueous samples by in-vial derivatization and headspace solid-phase microextraction (SPME)-gas chromatography (GC)-mass spectrometry (MS) has been fully automated using a Twin PAL dual-arm robotic system. Linearity, accuracy, sensitivity for a series of n-methyl, n-ethyl, and n-phenyl metal substituted chloride compounds of tin, lead, and mercury were investigated. The automated method was compared to similar manual methods and improved precision, speed and throughput was achieved. By originally programming the Twin PAL dual-arm system with the supplier's software (Cycle Composer, Version 1.5.0) the arms on the robot were only able to work in sequence. However, in order to have a flexible system and exploit time efficiently the robotic arms must work simultaneously. This was accomplished by programming the robot with the new software package called Cruise Control 4-2 for Twin PALs. Compared to Cycle Composer, Cruise Control 4-2 enhanced the speed and throughput of the automated system further. In addition, with a built-in crash prevention protocol and an improved user interface a more user-friendly system was obtained.     

Spectrophotometric determination of iodate,iodide and acids by flow injection analysis

The production of iodine by reaction of iodate and iodide in acidic solution is used for the spectrophotometric determination of 1–6 × 10^?5 M iodate, 2–8 × 10^?3 M iodide, and ca. 10^?3 M acids. The sample is injected into a carrier stream containing the other two ions. The injection rate is ca. 100 h^?1.     

Analysis of tetramethylene disulfotetramine in foods using solid-phase microextraction-gas chromatography-mass spectrometry

An automated solid-phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS) method for the determination of tetramethylene disulfotetramine in foods was developed. A comparison of direct immersion (DI) and headspace (HS) extraction techniques using a 70microm carbowax/divinylbenzene (CW/DVB) fiber is presented. The optimized DI-SPME method provided an aqueous extraction limit of detection (LOD) of 9.0ng/g while the HS-SPME LOD was 2.7ng/g. In both SPME modes, recovery was highly matrix dependent and quantification requires standard addition calibrations. Analysis of foods using DI-SPME encountered many obstacles including fiber fouling, low recovery and poor reproducibility. HS-SPME was successfully applied to food analysis with minimal interferences. Standard addition calibration curves for foods gave high linearity (R2>0.98), reproducibility (RSD<12%) and sensitivity with LODs ranging from 0.9 to 4.3ng/g.     

Quick analytical method for the determination of iodide and iodate ions in aqueous solutions

An analytical quick-test method was developed to determine iodide and iodate ions in aqueous solutions using solid phase extraction cartridges for sample preparation. Work was focussed on finding simple, but efficient conditions for quantitative separation of iodate and iodide. Iodine amounts were then determined by standard methods. Ion-exchange absorbers in cartridge form were used. Selectivity and yield of the species separation were studied at pH value of 5-10 and various solution compositions using ¹³¹I radioactive tracer. The electrolytes used were diluted alkaline, nitrate and boric acid-borate solutions. Application to nuclear reactor cooling water analysis or environmental investigations and monitoring is proposed.     

Solid-phase microextraction-gas chromatography-mass spectrometry of biologically active substances in water samples

High-flow pneumatically assisted electrospray ionization mass spectrometry (ESI-MS) has been extensively used for the characterization and determination of peptides and peptide hormones available for biomedical research and therapeutic applications. The aim of this study was to optimize a method of characterization and determination of a mixture of peptide hormones with therapeutic interest by liquid chromatography (LC) coupled to ESI-MS. In this work the linear solvation energy relationship methodology was used in order to optimize the mobile phase to be used in the LC separation of the peptide hormone series and the operational parameters of the source and analyzer of ESI were also optimized to obtain the best signal stability and the highest sensitivity. To validate the proposed method for peptide hormone analysis, quality parameters were determined and satisfactory results were obtained. Likewise, the method detection limit was picomole level for most of the peptides employing selected-ion monitoring of the [M+nH]n+ ions.     

Determination of terpenes in tequila by solid phase microextraction-gas chromatography-mass spectrometry

Solid phase microextraction and capillary gas chromatography-mass spectrometry were used for the determination of seven terpenes in tequila. The method was selected based on the following parameters: coating selection (PA, PDMS, CW/DVB, and PDMS/DVB), extraction temperature, addition of salt, and extraction time profile. The extraction conditions were: PDMS/DVB fiber, Headspace, 100% NaCl, 25 degrees C extraction temperature, 30 min extraction time and stirring at 1200 rpm. The calibration curves (50-1000 ng/ml) for the terpenes followed linear relationships with correlation coefficients (r) greater than 0.99, except for trans,trans-farnesol (r = 0.98). RSD values were smaller than 10% confirmed that the technique was precise. Samples from 18 different trade brands of "Aged" tequila analyzed with the developed method showed the same terpenes in different concentrations. The analytical procedure used is selective, robust (more than 100 analyses with the same fiber), fast and of low-cost.     

Screening of Brazilian fruit aromas using solid-phase microextraction-gas chromatography-mass spectrometry

Manual headspace solid-phase microextraction (SPME) coupled to gas chromatography-mass spectrometry (GC-MS) was used for the qualitative analysis of the aromas of four native Brazilian fruits: cupuassu (Theobroma grandiflorum, Spreng.), cajá (Spondias lutea. L.), siriguela (Spondias purpurea, L.) and graviola (Anona reticulata, L). Industrialized pulps of these fruits were used as samples, and extractions with SPME fibers coated with polydimethylsiloxane, polyacrylate, Carbowax and Carboxen were carried out. The analytes identified included several alcohols, esters, carbonyl compounds and terpernoids. The highest amounts extracted, evaluated from the sum of peak areas, were achieved using the Carboxen fiber.     

Optimization of experimental parameters in single-drop microextraction-gas chromatography-mass spectrometry for the determination of periodate by the Malaprade reaction, and its application to ethylene glycol

The aim of present work was to optimize the experimental parameters in single drop microextraction under solution immersion (SDME) and headspace (HS-SDME) extraction modes for the determination of periodate using guaifenesine [3-(2′-methoxyphenoxy)-1,2-propane diol] and norephedrine (phenylpropanolamine) as new and alternative reagents for the Malaprade reaction. The reactions were complete within 5 min resulting in the formation of 2-(2′-methoxyphenoxy)-acetaldehyde and benzaldehyde, respectively. SDME/HS-SDME of oxidation products with 2 μl of anisole or 1 μl of toluene, respectively, has permitted the determination of periodate at μg l⁻¹ concentration levels. The results indicated that HS-SDME (range 0.01-10 mg l⁻¹, r² = 0.9990; limit of detection 1.55 μg l⁻¹) was more sensitive than SDME (range 0.05-50 mg l⁻¹, r² = 0.9984; limit of detection 3.42 μg l⁻¹), and was inexpensive, rapid and convenient. Tolerance of excess of iodate has permitted the application of this method in the determination of ethylene glycol in motor oil; the average recovery on spiked sample was 98.6% with R.S.D. of 4.2%.     

Determination of polycyclic aromatic hydrocarbons in water by solid-phase microextraction-gas chromatography-mass spectrometry

A solid-phase microextraction (SPME)-gas chromatography (GC)-mass spectrometry (MS) analytical method for the simultaneous separation and determination of 16 polycyclic aromatic hydrocarbons (PAHs) from aqueous samples has been developed, based on the sorption of target analytes on a selectively sorptive fibre and subsequent desorption of analytes directly into GC-MS. The influence of various parameters on PAH extraction efficiency by SPME was thoroughly studied. Results show that the fibre exposure time and the use of agitation during exposure are critical in enhancing SPME performance. The presence of colloidal organic matter (as simulated by humic acid) in water samples is shown to significantly reduce the extraction efficiency, suggesting that SPME primarily extracts the truly dissolved compounds. This offers the significant advantage of allowing the differentiation between freely available dissolved compounds and those associated with humic material and potentially biologically unavailable. The method showed good linearity up to 10 μg/l. The reproducibility of the measurements expressed as relative standard deviation (R.S.D.) was generally <20%. The method developed was then applied to extract PAHs from sediment porewater samples collected from the Mersey Estuary, UK. Total PAH concentrations in porewater were found to vary between 95 and 742 ng/l with two to four ring PAHs predominating. Results suggest that SPME has the potential to accurately determine the dissolved concentrations of PAHs in sediment porewater.     

Solid-phase microextraction-gas chromatography-mass spectrometry for the analysis of selective serotonin reuptake inhibitors in environmental water

The continuous contamination of surface waters by pharmaceuticals is of most environmental concern. Selective serotonin reuptake inhibitors (SSRIs) are drugs currently prescribed for the treatment of depressions and other psychiatric disorders and then, they are among the pharmaceuticals that can occur in environmental waters. Solid-phase microextraction (SPME) coupled to gas chromatography-mass spectrometry has been applied to the extraction of five SSRIs--venlafaxine, fluvoxamine, fluoxetine, citalopram and sertraline--from water samples. Some of the analytes were not efficiently extracted as underivatized compounds and so, an in situ acetylation step was introduced in the sample preparation procedure. Different parameters affecting extraction efficiency such as extraction mode, fiber coating and temperature were studied. A mixed-level fractional factorial design was also performed to simultaneously study the influence of other five experimental factors. Finally, a method based on direct SPME at 100 degrees C using polydimethylsiloxane-divinylbenzene fibers is proposed. The performance of the method was evaluated, showing good linearity and precision. The detection limits were in the sub-ng/mL level. Practical applicability was demonstrated through the analysis of real samples. Recoveries obtained for river water and wastewater samples were satisfactory in all cases. An important aspect of the proposed method is that no matrix effects were observed. Two of the target compounds, venlafaxine and citalopram, were detected and quantified in a sewage water sample.