Langmuir probe measurements of electron temperature in an inductively coupled plasma

The feasibility of using double Langmuir probes to measure electron temperature (T_e) in an Ar inductively coupled plasma (ICP) was evaluated. Experimental methods for probing the plasma and for reducing rf interference were devised. Despite these measures, the probe signal was noisy and erratic if the ICP had the normal analytical configuration with a hole through its center, so measurements were restricted to an ICP without an axial channel. Theoretical criteria indicated that Langmuir probe measurements in an atmospheric pressure ICP were in a borderline regime in which the measured T_e values may have been depressed somewhat (relative to the actual T_e values in the ICP) due to cooling of electrons as they approached the probe. The T_e values obtained from the center of the ICP were 7500 K at a forward power of 1.0 kW and 10 000 K at 1.25 kW for a measurement position 8 mm above the load coil. Electron density (n_e) measurements by the Langmuir probe method were comparable to or higher than n_e values calculated from the Saha equation at the measured T_es. The T_e and n_e values were high enough to indicate that, if electron cooling and ion-electron recombination occurred near the probes, these effects were not extreme and/or the use of two probes compensated for them in some fashion. The probe measurements also indicated that T_e increased with the potential difference between the probes. This latter observation provided tentative evidence that the electron kinetic energy distribution was non-Maxwellian with an excess of higher energy electrons relative to lower energy electrons.     

Effects of sampler-skimmer separation in inductively coupled plasma-mass spectrometry

The effects of varying the sampler-skimmer spacing in an inductively coupled plasma-mass spectrometer are illustrated. The signals for a number of species were monitored including background ions (ArN⁺, ArO⁺, ArOH⁺, Ar₂⁺, Ar₂H⁺), background continuum, analyte ions (Cu⁺, Ce⁺, La⁺), analyte oxide ions (CeO⁺, LaO⁺), and matrix induced ions (ArNa⁺). As the sampler-skimmer spacing is increased over that normally used, the signal for some species decreases in intensity while the signal for others increases in intensity. There is a wide range of differential behavior and in some cases the signal changes are quite dramatic.

In addition to presenting results for an Ar plasma, measurements are also presented for a N₂-Ar mixed gas plasma. For some species, the signal changes observed when the sampler-skimmer spacing is increased are quite different with the N₂-Ar mixed gas plasma than with the Ar plasma and are, in some cases, opposite to signal changes observed with the Ar plasma. It appears that a larger sampler-skimmer spacing is more appropriate for a N₂ mixed gas plasma than the spacing normally used for a pure Ar plasma. Finally the effect of sampler-skimmer spacing on matrix effects is presented and it appears that matrix effects are not induced in the zone between the sampler and the skimmer.     

Determination of U in environmental samples by single extraction chromatography coupled to triple-quadrupole inductively coupled plasma-mass spectrometry

In order to measure trace ²³⁶U and ²³⁶U/²³⁸U in environmental samples with a high matrix effect, a novel and simple method was developed that makes the digestion and purification procedures compatible with advanced triple-quadrupole inductively coupled plasma-mass spectrometry. A total dissolution of sample with HF + HNO₃ + HClO₄ was followed by chromatographic separation with a single resin column containing normal type DGA resin (N,N,N′,N’-tetra-n-octyldiglycolamide) as the extractant system. The analytical accuracy and precision of ²³⁶U/²³⁸U ratios, measured as ²³⁶U¹⁶O⁺/²³⁸U¹⁶O⁺, were examined by using the reference materials IAEA-135, IAEA-385, IAEA-447, and JSAC 0471. The low method detection limit (3.50 × 10⁻⁶ Bq kg⁻¹) makes it possible to perform routine monitoring of environmental ²³⁶U due to global fallout combined with the Fukushima Daiichi Nuclear Power Plant accident fallout (>10⁻⁵ Bq kg⁻¹). Finally, the developed method was successfully applied to measure ²³⁶U/²³⁸U ratios and ²³⁶U activities in soil samples contaminated by the accident. The low ²³⁶U/²³⁸U atom ratios ((1.50–13.5) × 10⁻⁸) and ²³⁶U activities ((2.25–14.1) × 10⁻² mBq kg⁻¹) indicate ²³⁶U contamination was mainly derived from global fallout in the examined samples.     

Fundamental aspects of ion extraction in inductively coupled plasma mass spectrometry

The present understanding of the ion extraction process in inductively coupled plasma mass spectrometry (ICP-MS) is reviewed critically. Topics include ion production in the ICP, origins of polyatomic ions, causes of and remedies for the secondary discharge, properties of the supersonic jet and of the beam leaving the skimmer, space charge effects, and matrix interferences. Areas of recent interest are also described from the perspective of the ion extraction process. These recent topics include “cool” plasmas, the three-aperture interface, ion extraction from helium plasmas, and ion sampling considerations unique to magnetic sector, time-of-flight, and ion trap mass spectrometers.     

Automatic selection of internal standards in inductively coupled plasma-mass spectrometry

The automatic selection of internal standards in inductively coupled plasma-mass spectrometry was performed using a cluster analysis algorithm. The samples contained 25 analytes, spanning the atomic mass and ionization potential ranges, and a single interfering element. The interferents examined were Na, Mg, K, Zn, Ba, and Pb. The cluster analysis algorithm used kinetic energy, ionization potential, oxide bond strength, hydride bond strength, and electronegativity, to group the analytes. These variables were weighted differently in the various matrices. The performance of the clustering method and selection of internal standards was good for most analytes in the various matrices.     

On-line coupling of gel electrophoresis and inductively coupled plasma-mass spectrometry

The on-line coupling of gel electrophoresis with inductively coupled plasma-mass spectrometry (GE-ICP-MS) is a powerful tool for simultaneous separation, detection and quantification of bio-molecules, and has been applied to the determination of phosphorus in DNA, phosphoproteins, and phosphopeptides, gold in nano-particles, iron in metalloproteins, and iodine in aerosols, and cisplatin-oligonucleotide interactions. However, since the first report in 2005, relatively few papers have been published, perhaps reflecting the lack of familiarity with the benefits of this promising methodology. So, here for the first time, we critically review the applications of GE-ICP-MS, and explore the advantages and the limitations of the technique for various applications. Such scrutiny may be useful in not only the development of the technique but also highlighting its potential in proteomics, genomics and metallomics.     

浊点萃取-电感耦合等离子体质谱法测定植物样品中的痕量铂与钯

建立了浊点萃取电感耦合等离子体质谱法测定植物样品中痕量铂与钯的方法,方法检出限分别为0.17 ng/g和0.10 ng/g,样品加标回收率在85%～110%之间。利用建立的方法对采自北京环路旁的植物样品进行了测定,铂与钯含量范围分别为0.35～5.35 ng/g和1.95～10.85 ng/g,钯的含量普遍高于铂的含量。     

电感耦合等离子体质谱法测定地球化学样品中镉

采用HF-HClO4-HNO3-H2SO4分解样品,王水提取,选用4个国家一级标准物质制备成标准系列校准,ICP-MS法直接测定地球化学样品中的Cd。选择103Rh为内标,确定了仪器的最佳分析条件,研究了Zr,Sn对Cd的干扰,选择114Cd作为测定同位素,采用数学公式校正了Sn对Cd的同质异位素干扰,方法检测限(3s)为6.3×10-3μg/g,RSD(n=12)为3.9%～6.6%。经国家一级标准物质验证,测定值与标准值吻合较好。该方法适用于地球化学样品中的微量Cd的测定。     

Microwave assisted extraction of iodine and bromine from edible seaweed for inductively coupled plasma-mass spectrometry determination

The feasibility of microwave energy to assist the solubilisation of edible seaweed samples by tetramethylammonium hydroxide (TMAH) has been investigated to extract iodine and bromine. Inductively coupled plasma-mass spectrometry (ICP-MS) has been used as a multi-element detector. Variables affecting the microwave assisted extraction/solubilisation (temperature, TMAH volume, ramp time and hold time) were firstly screened by applying a fractional factorial design (2^5-1 + 2), resolution V and 2 centre points. When extracting both halogens, results showed statistical significance (confidence interval of 95%) for TMAH volume and temperature, and also for the two order interaction between both variables. Therefore, these two variables were finally optimized by a 2² + star orthogonal central composite design with 5 centre points and 2 replicates, and optimum values of 200 °C and 10 mL for temperature and TMAH volume, respectively, were found. The extraction time (ramp and hold times) was found statistically non-significant, and values of 10 and 5 min were chosen for the ramp time and the hold time, respectively. This means a fast microwave heating cycle. Repeatability of the over-all procedure has been found to be 6% for both elements, while iodine and bromine concentrations of 24.6 and 19.9 ng g⁻¹, respectively, were established for the limit of detection. Accuracy of the method was assessed by analyzing the NIES-09 (Sargasso, Sargassum fulvellum) certified reference material (CRM) and the iodine and bromine concentrations found have been in good agreement with the indicative values for this CRM. Finally, the method was applied to several edible dried and canned seaweed samples.     

Arsenic speciation in water and biota samples at trace levels by ion chromatography inductively coupled plasma-mass spectrometry

A sensitive, reliable, simple and rapid analytical method was developed for the determination of arsenite [As(III)], arsenate [As(V)] and arsenobetaine (AsB) species using ion chromatography combined with inductively coupled plasma-mass spectrometry (IC-ICP-MS). Inorganic and organic arsenic species were separated with an anion exchange column (Dionex AS9) and a 50 mM sodium bicarbonate mobile phase (pH 10) at a flow rate of 1.0 mL min^?1. %RSD values were found to be lower than 5.1% for all arsenic species. The limits of detection (LOD) obtained for As(III), As(V) and AsB were 16.5 ng L^?1, 14.1 ng L^?1 and 6.2 ng L^?1, respectively. The developed analytical method was tested using AsB certified reference material (NMIJ CRM 7901-a), and spring water certified reference material (UME CRM 1201) for accuracy check. This method was applied for the quantitative determination of arsenic species in different water samples and chicken samples as a solid matrix.     

Determination of metals in composite diet samples by inductively coupled plasma-mass spectrometry

A study was conducted to evaluate the applicability of inductively coupled plasma-mass spectrometry (ICP-MS) techniques for determination of metals in composite diets. Aluminum, cadmium, chromium, copper, lead, manganese, nickel, vanadium, and zinc were determined by this method. Atmospheric pressure microwave digestion was used to solubilize analytes in homogenized composite diet samples, and this procedure was followed by ICP-MS analysis. Recovery of certified elements from standard reference materials ranged from 92 to 119% with relative standard deviations (RSDs) of 0.4-1.9%. Recovery of elements from fortified composite diet samples ranged from 75 to 129% with RSDs of 0-11.3%. Limits of detection ranged from 1 to 1700 ng/g; high values were due to significant amounts of certain elements naturally present in composite diets. Results of this study demonstrate that low-resolution quadrupole-based ICP-MS provides precise and accurate measurements of the elements tested in composite diet samples.     

High resolution studies of the origins of polyatomic ions in inductively coupled plasma-mass spectrometry,Part I. Identification methods and effects of neutral gas density assumptions,extraction voltage,and cone material

Common polyatomic ions (ArO⁺, NO⁺, H₂O⁺, H₃O⁺, Ar₂⁺, ArN⁺, OH⁺, ArH⁺, O₂⁺) in inductively coupled plasma-mass spectrometry (ICP-MS) are identified using high mass resolution and studied using kinetic gas temperatures (T_gas) determined from a dissociation reaction approach. Methods for making accurate mass measurements, confirming ion identifications, and correcting for mass bias are discussed. The effects of sampler and skimmer cone composition and extraction voltage on polyatomic ion formation are also explored. Neutral species densities at several locations in the extraction interface are estimated and the corresponding effects of the T_gas value are calculated. The results provide information about the origins of background ions and indicate possible locations for their formation or removal.     

Measurements of contaminant elements of wines by inductively coupled plasma-mass spectrometry: A comparison of two calibration approaches

The aim of the present work was to develop and validate an accurate method by ICP-MS focalized to the measurement of contaminant elements in wines, in special those with legal importance. In addition, we intended to evaluate the suitability of ICP-MS semi-quantitative methodology in order to reduce the time and cost of analysis. Twenty-six contaminant elements of wine (Li, Be, Al, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, As, Se, Rb, Sr, Ag, Cd, In, Cs, Ba, Hg, Tl, Pb, Bi and U) were measured using quantitative and semi-quantitative calibration approaches, in diluted white and red wines. In an early step potential interferences caused by Cl and Ca species were evaluated, in order to establish suitable mathematical corrections. For validation of ICP-MS procedures a few elements were determined by flame and electrothermal AAS. Reference wines from 1992 year, with provisional values, were analyzed and the results showed satisfactory agreement. The semi-quantitative calibration provided slightly higher limits of detection than those obtained by the quantitative calibration, and always lower than 0.1 μg l⁻¹, except for Fe and Zn. For most elements the recovery percentages (between 90 and 100%) and precision of the results (R.S.D. (%) < 4) were similar for both modes. Differences lower than 20% of concentration was obtained for most elements. Both methodologies offer valuable alternatives to wine characterization and comparison purposes. For legal requirements control purposes, with reference to the importance of accurate results, quantitative approach is the most suitable alternative.     

Considerations of particle vaporization and analyte diffusion in single-particle inductively coupled plasma-mass spectrometry

The intensity of individual gold nanoparticles with nominal diameters of 80, 100, 150, and 200 nm was measured using single-particle inductively coupled plasma-mass spectrometry (ICP-MS). Since the particles are not perfectly monodisperse, a distribution of ICP-MS intensity was obtained for each nominal diameter. The distribution of particle mass was determined from the transmission electron microscopy (TEM) image of the particles. The distribution of ICP-MS intensity and the distribution of particle mass for each nominal diameter were correlated to give a calibration curve. The calibration curves are linear, but the slope decreases as the nominal diameter increases. The reduced slope is probably due to a smaller degree of vaporization of the large particles.In addition to the degree of particle vaporization, the rate of analyte diffusion in the ICP is an important factor that determines the measured ICP-MS intensity. Simulated ICP-MS intensity versus particle size was calculated using a simple computer program that accounts for the vaporization rate of the gold nanoparticles and the diffusion rate and degree of ionization of the gold atoms. The curvature of the simulated calibration curves changes with sampling depth because the effects of particle vaporization and analyte diffusion on the ICP-MS intensity are dependent on the residence time of the particle in the ICP. Calibration curves of four hypothetical particles representing the four combinations of high and low boiling points (2000 and 4000 K) and high and low analyte diffusion rates (atomic masses of 10 and 200 Da) were calculated to further illustrate the relative effects of particle vaporization and analyte diffusion. The simulated calibration curves show that the sensitivity of single-particle ICP-MS is smaller than that of the ICP-MS measurement of continuous flow of standard solutions by a factor of 2 or more. Calibration using continuous flow of standard solution is semi-quantitative at best.An empirical equation is formulated for the estimation of the position of complete vaporization of a particle in the ICP. The equation takes into account the particle properties (diameter, density, boiling point, and molecular weight of the constituents of the particle) and the ICP operating parameters (ICP forward power and central channel gas flow rate). The proportional constant and exponents of the variables in the equation were solved using literature values of ICP operating conditions for single-particle inductively coupled plasma-mass spectrometry (ICP-MS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES) measurements of 6 kinds of particles in 12 studies. The calculated position is a useful guide for the selection of sampling depth or observation height for ICP-MS and ICP-AES measurements of single particles as well as discrete particles in a flow, such as laser-ablated materials and airborne particulates.     

Determination of trace elements in organic material by inductively coupled plasma-mass spectrometry

Summary For purposes of trace element analysis of organic materials a combined analytical procedure is tested. It consists of a pressure decomposition by nitric acid at 220° C in quartz vessels. The measurements are performed in the diluted digests by inductively coupled plasma/mass spectrometry. Analytical figures of merit are given.Dedicated to Prof. Dr. Karl Winsauer on the occasion of his 60th birthday.     

Multielemental analysis of food and agricultural matrixes by inductively coupled plasma-mass spectrometry

The suitability of quadrupole inductively coupled plasma-mass spectrometry (ICP-MS) for multielemental analysis of food following microwave closed vessel digestion of samples was evaluated in relation to analytical challenges presented by some major food and agricultural matrixes. Fifteen key analytes (Al, As, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Se, Sn, V, Zn) were determined in 9 reference materials representative of 3 major groups of staple foods (cereals, seafood, and meat). For all measurements, the method of external calibration was used and Rh was selected as internal standard. Matrix-induced interferences were evaluated for each material, and suitable methods to overcome them were applied. Spectral interferences caused by C, Cl, and Ca content of digestates were quantitated and corrected by entering a simple system of mathematical correction equations into the instrument software before each analytical run. Full mastering of interferences together with adoption of a series of measures to control the reliability of analytical measurements produced accurate results for all the analytes. A standard analytical protocol is outlined for the benefit of both research and routine high-throughput laboratories that perform ICP-MS analyses of food.     

Determination of seven arsenic species in seafood by ion exchange chromatography coupled to inductively coupled plasma-mass spectrometry following microwave assisted extraction: method validation and occurrence data

The determination of seven arsenic species in seafood was performed using ion exchange chromatography on an IonPac AS7 column with inductively coupled plasma mass spectrometry detection after microwave assisted extraction. The effect of five parameters on arsenic extraction recoveries was evaluated in certified reference materials. The recoveries of total arsenic and of arsenic species with the two best extraction media (100% H₂O and 80% aqueous MeOH) were generally similar in the five seafood certified reference materials considered. However, because MeOH co-elutes with arsenite, which would result in a positively biased arsenite concentration, the 100% H₂O extraction conditions were selected for validation of the method. Figures of merit (linearity, LOQs (0.019-0.075 mg As kg⁻¹), specificity, trueness (with recoveries between 82% (As(III)) and 104% (As(V) based on spikes or certified concentrations), repeatability (3-14%), and intermediate precision reproducibility (9-16%) of the proposed method were satisfactory for the determination of arsenite, monomethylarsonic acid, dimethylarsinic acid, arsenate, arsenobetaine and arsenocholine in fish and shellfish. The performance criteria for trimethylarsine oxide, however, were less satisfactory. The method was then applied to 65 different seafood samples. Arsenobetaine was the main species in all samples. The percentage of inorganic arsenic varied between 0.4-15.8% in shellfish and 0.5-1.9% at the utmost in fish. The main advantage of this method that uses only H₂O as an extractant and nitric acid as gradient eluent is its great compatibility with the long-term stability of both IEC separation and ICP-MS detection.     

高效色谱-电感耦合等离子体质谱法分析海藻类海产品中砷的形态

采用阴(Hamilton PRP-X100柱)阳(Dionex Ionpac CS-10柱)离子交换色谱-电感耦合等离子体质谱联用技术,分别以pH 10.3的20 mmol/L NH4HCO3和pH 2.0的5 mmol/L吡啶溶液为流动相,建立了As(Ⅲ)、As(Ⅴ)、一甲基砷酸(MMA)、二甲基砷酸(DMA)、砷甜菜碱AsB、砷糖PO4、砷糖OH、砷糖SO3、砷糖SO4砷形态的分析方法。采用微波消解法和超声溶剂提取法对不同海域10种紫菜和海带产品进行前处理,对As含量及其化学形态进行分析。实验表明,样品总砷的质量分数为1.7～38.7 mg/kg,样品萃取物中,As糖PO4和As糖OH为As的主要形态,其含量分别占可提取As的6.5%～67.7%和12.9%～86.2%,海带样品萃取物中还有As糖SO3和DMA被检测,其含量分别占可提取As的13.0%～52.1%和5.9%～17.4%。在紫菜和海带海藻类产品中,含As的化合物主要是毒性较低的有机砷。     

Ion trajectories through the input ion optics of an inductively coupled plasma-mass spectrometer

A commercial program (MacSimion) has been used to model the einzel lens and bessel box input lens system of an inductively coupled plasma-mass spectrometer (ICP-MS). A number of plots are presented illustrating the effect of various lens voltages on ion trajectories. The trajectories are dependent on ion kinetic energy and since ion kinetic energy is mass dependent in ICP-MS, these plots clarify the mass dependence of ion lens voltage settings. Plots are also presented illustrating the interdependence of some lens voltage settings and how, in fact, different lens voltage settings can result in similar ion throughput. The model can be used to predict relative signal intensities for a range of ion masses as a function of lens potentials and these are shown to agree with experimentally measured data.