Design and evaluation of an on-line microcolumn pre-concentration technique for graphite furnace atomic absorption spectrometry

Summary A simple method is described for trace element pre-concentration on a microcolumn of inner diameter 1 mm and 25 mm length. The column packed with methacrylate gel with bound 8-quinolinol groups (Spheron Oxin) is incorporated into the tip of the sampling arm of the autosampler. The sample solution, water, eluent and air streams are switched with an eight-port valve. The flow-rate at pre-concentration is about 0.14 ml/min. After washing out the residues of the sample matrix from the column, the collected elements are eluted with 1 mol/l HNO₃ directly into the graphite tube of the atomizer. The reproducibility of the method was found to be better than 5%. The method was used for the determination of Pb in NaCl.

---

Entwurf und Abschätzung einer on-line Mikrosäulen-Vorkonzentrierungstechnik für die Graphitofen-Atomabsorptionsspektrometrie

     

Determination of Hg in seawater by inductively coupled plasma mass spectrometry after on-line pre-concentration

A method for the determination of Hg in seawater by inductively coupled plasma mass spectrometry, after an on-line separation and pre-concentration, is described. The matrix separation was accomplished by retention of the Hg complex with the ammonium salt of O,O-diethyl dithiophosphoric acid on C₁₈ immobilized on silica in a micro-column. Before pre-concentration, the seawater sample was acidified with HNO₃ to 0.14 mol l⁻¹. Methanol was used as the eluent, which was introduced into the conventional pneumatic nebulizer of the instrument. External calibration with aqueous analytical solutions, submitted to the same procedure, was used. An enhancement factor of 16 was obtained, and the limit of detection was 5 ng l⁻¹. The sample consumption was 2.3 ml per determination, and the sampling frequency was 21 h⁻¹. The accuracy was tested by comparison with vapor generation inductively coupled plasma mass spectrometry. The agreement between the Hg concentrations measured by the two methods in the seawater samples was good.     

Rapid radiochemical separation in neutron activation analysis : Part 1. The use of C18-bonded silica gel and selective complexation for determinations of manganese,copper and zinc in biological materials

A rapid radiochemical separation method based on the removal of metal ions by columns of C₁₈-bonded silica gel after selective complexation by 8-quinolinol, ammonium pyrolidinedithiocarbamate or cupferron is described for the determination of manganese, copper and zinc in neutron-activated biological materials. The removal of the metal ions, either by adsorption or by a combination of filtration and adsorption on columns of C₁₈-bonded silica gel, was investigated to optimise the separation procedure. Analysis of several National Bureau of Standards and International Atomic Energy Agency biological reference materials demonstrated the effectiveness of this technique. The method is simple and reliable and readily adaptable in all radiochemical laboratories. Furthermore, columns of C₁₈-bonded silica gel have been successfully recycled a number of times without deterioration.     

Separation and preconcentration by flow injection coupled to tungsten coil electrothermal atomic absorption spectrometry

A flow injection system coupled to a tungsten coil electrothermal atomizer has been developed for on-line separation and preconcentration, using lead as a model element. The system utilizes three-way solenoid valves for sampling, buffering, washing and reconditioning solution management, and the resin column is inserted in the tip of the autosampler arm of a Varian GTA-96. The solenoid valves and tungsten coil power supply were controlled by a computer program written in Visual Basic, interfaced with the built-in Varian software. The system performance was tested by loading the resin column with the sample flowing at 3 ml min⁻¹ for 60 s. Elution was performed automatically by sampling 20 μl of the eluent from a sample cup of the autosampler, and this aliquot was delivered into a 150 W tungsten coil. With Chelex-100 resin, the separation of concomitants was tested with lead in the presence of as much as 1000 mg l⁻¹ of Ca, Mg, Na or K. The model system presented an enrichment factor of 64 at a sampling rate of 30 samples per hour.     

In situ continuous derivatization/pre-concentration of carbonyl compounds with 2,4-dinitrophenylhydrazine in aqueous samples by solid-phase extraction: Application to liquid chromatography determination of aldehydes

A rapid and straightforward continuous solid-phase extraction system has been developed for in situ derivatization and pre-concentration of carbonyl compounds in aqueous samples. Initially 2,4-dinitrophenylhydrazine, the derivatizing agent, was adsorbed on a C₁₈ mini-column and then 15-ml of sample were continuously aspirated into the flow system, where the derivatization and pre-concentration of the analytes (low-molecular mass aldehydes) were performed simultaneously. Following elution, 20 μl of the extract were injected into a LC-DAD system, in which hydrazones were successfully separated in 12 min on a RP-C₁₈ column using a linear gradient mobile phase of acetonitrile-water of 60-100% acetonitrile for 8 min, flowing at 0.5 ml/min. The whole analytical process can be accomplished within ca. 35 min. Under optimum conditions, limits of detection were obtained between 0.3 and 1.0 μg/l and RSDs (inter-day precision) from 1.2 to 4.6%. Finally, some applications on water samples are presented with recoveries ranged from 95.8 to 99.4%.     

N-Methylimidazolium ionic liquid-functionalized silica as a sorbent for selective solid-phase extraction of 12 sulfonylurea herbicides in environmental water and soil samples

A novel material for solid-phase extraction (SPE) was synthesized by chemical immobilization of a functionalized N-methylimidazolium ionic liquid on silica gel. Cartridges packed with the synthetic material were successfully applied to the pre-concentration of trace-level thifensulfuron-methyl, metsulfuron-methyl, chlorsulfuron, sulfometuron-methyl, rimsulfuron, ethametsulfuron, tribenuron-methyl, bensulfuron-methyl, prosulfuron, pyrazosulfuron, chlorimuron-ethyl and primisulfuron from environmental water and soil samples. The 12 sulfonylurea herbicides (SUs) obtained a good resolution in less than 50 min using HPLC with a UV detector. The recovery studies using the ionic liquid-functionalized silica as a sorbent were performed by three consecutive extractions of water and soil samples at two spiked levels. The average recovery for each analyte was in the range of 53.8–118.2% for the water samples and 60.9–121.3% for the soil sample, with RSDs lower than 11.3% in all cases. The ionic liquid-functionalized silica cartridges showed higher selectivity for the SUs than commercially available C₁₈ cartridges did.     

Sorption and preconcentration of copper and cadmium on silica gel modified with 3-aminopropyltriethoxysilane

3-Aminopropyltriethoxysilane, (C₂H₅O)₃ Si(CH₂)₃NH₂, loaded on silica gel was used as a pre-concentration sorbent for copper and cadmium prior to their determination by flame atomic absorption spectrometry (FAAS). Both batch and column methods were used for the separation of the above metals. The analytes are quantitatively retained on the proposed adsorbent at pH 6.5. The complexation capacity of the collector is 0.032 mmol Cu/g silica. In the batch method, the effects of shaking time and the ratio of metal/silica on the retention by the asorbent were investigated. Columns filled with the collector provided quantitative recovery of the above metals from standardized samples as well as from sodium chloride solutions.     

Determination of Selected Persistent Organochlorine Pollutants in Human Serum by Solid-phase Disk Extraction and Dual-Column Capillary Gas Chromatography with Electron Capture Detection

Abstract

An improved clean-up method by solid-phase disk extraction was developed to isolate and concentrate trace levels of POPs (persistent organochlorine pollutants) in human serum prior to gas chromatography with electron capture detection on two different capillary columns, providing an improved selectivity. An Empore^TM C₁₈ bonded silica extraction disk cartridge is used for the initial extraction and enrichment of the analytes. Subsequent clean-up is achieved by concentrated sulphuric acid and silica gel adsorption chromatography. Recoveries for selected POPs are ranging from 62 to 74% and a good reproducibility (RSD < 14%) is demonstrated. Human samples analysed under these conditions, show a similar relative concentration profile.     

Use of direct injection precolumn techniques for the high-performance liquid chromatographic determination of the retinoids acitretin and 13-cis-acitretin in plasma.

A previously developed highly sensitive high-performance liquid chromatographic method for the determination of retinoids, using direct injection of large plasma volumes, on-line solid-phase extraction and ultraviolet detection, was improved and fully validated for the determination of acitretin and 13-cis-acitretin in plasma samples. The addition of acetonitrile to improve the recovery was performed on-line by a T-piece, avoiding any cis-trans isomerization which could occur when acetonitrile was added prior to storage in the autosampler. About 30 injections could be made onto one precolumn despite the large injection volume (1 ml of plasma containing the internal standard). Full automation was attained by the use of automated precolumn replacement. In addition, forward- and back-flush purging of the precolumn enhanced the longevity of the analytical column. This consisted of three coupled C18 columns of 125 mm length each. The quantification limit was 0.3 ng/ml, using ultraviolet detection at 360 nm, and the mean inter-assay precision was 3.8% for the two compounds.     

Determination of arsenic(III) and arsenic(V) by electrothermal atomic absorption spectrometry after complexation and sorption on a C-18 bonded silica column

A flow injection procedure for the separation and pre-concentration of inorganic arsenic based on the complexation with ammonium diethyl dithiophosphate (DDTP) and sorption on a C-18 bonded silica gel minicolumn is proposed. During the sample injection by a time-based fashion, the As³⁺-DDTP complex is stripped from the solution and retained in the column. Arsenic(V) and other ions that do not form complexes are discarded. After reduction to the trivalent state by using potassium iodide plus ascorbic acid, total arsenic is determined by electrothermal atomic absorption spectrometry (ETAAS). Arsenic(V) concentration can be calculated by difference. After processing 6 ml sample volume, the As³⁺-DDTP complexes were eluted directly into the autosampler cup (120 μl). Ethanol was used for column rinsing. Influence of pH, reagent concentration, pre-concentration and elution time and column size were investigated. When 30 μl of eluate plus 10 μl of 0.1% (w/v) Pd(NO₃)₂ were dispensed into the graphite tube, analytical curve in the 0.3–3 μg As l⁻¹ range was obtained (r=0.9991). The accuracy was checked for arsenic determination in a certified water, spiked tap water and synthetic mixtures of arsenite and arsenate. Good recoveries (97–108%) of spiked samples were found. Results are precise (RSD 7.5 and 6% for 0.5 and 2.5 μg l⁻¹, n=10) and in agreement with the certified value of reference material at 95% confidence level.     

The potential of pre-columns to improve detection properties in high-performance liquid chromatography

Summary The potential of pre-columns to increase the selectivity and sensitivity in high-performance liquid chromatography is demonstrated by some case studies. An on-line pre-column of 5 cm was used for the determination of fluvoxamine and clovoxamine in plasma. In this example, the principle of using different packing materials in precolumn and analytical column is shown to be promising for certain applications of pre-columns for clean-up and pre-concentration. An on-line pre-column containing a 1–2 mm layer of stationary phase was successfully applied for the determination of secoverine in plasma and serum. Direct injection of 200–1000 l of the sample is possible. This study illustrates the high selectivity obtained by the combined use of a pre-column and an extraction detector. Sep-Pak C₁₈ cartridges were used both for clean-up and pre-concentration of soil extracts in order to isolate radio-labelled pesticides. In this way, the pretreatment of such complex samples is very rapid and simple.     

Solid phase extraction of amines

The objective of this paper is to provide information about solid phase extraction (SPE) as an alternative to liquid-liquid extraction of amines from several matrices. Different sorbents ranging from non-polar phases, such as C₁₈ silica to more polar such as cyanopropylsilica (CN) have been tested for analysis of aliphatic amines as monoamines, diamines and polyamines. Phenylalkylamines such as amphetamine or methamphetamine and heterocyclic amines such as histamine or cephalosporins (which also contain a carboxylic group), have also been studied. The different steps involved in the extraction procedure have been tested (conditioning, retention, pre-concentration, washing and elution) in order to obtain extracts free of interferences and enough sensitivity. C₁₈ silica (100 mg) was selected as optimal phase with recoveries nearly of 100%. The elution of more polar amines was performed in acidic conditions while less polar amines required organic solvents. Cephalosporin retention was performed in acid condition by using disk cartridges EM C_18, which gave better selectivity. The optimised clean-up procedures have been discussed to the quantification of the corresponding amines in real samples (urine, water and beer). The accuracy and precision were outlined.     

An integrated coupled column liquid chromatography system for the determination of leukotriene metabolites in biological samples

Summary A fully integrated chromatographic system was developed for the determination of leukotrienes in biological samples using photodiode-array detection (PDAD), which eliminates time consuming manual sample handling steps. A special solid phase extraction, (SPE) methodology for leucotriene metabolite stability was developed which increased the recoveries and eliminates the contamination risk of biological samples. The inherent instability (autooxidation) of many of the leukotriene mediators, and the adsorption effects onto exposed surfaces in vials and in the chromatographic system were found to be very important parameters to control in order to circumvent high loss of sample analytes. By binding the cell supernatants to the functionalities of the SPE support stabilised these mediators. Cell culture samples were eluted through a disposable C₁₈ SPE column. The SPE columns were allowed to thaw and deposited in an automated sample handling unit (ASPEC XL). Desorption of the analytes was followed by a second on-line SPE step, to eliminate remaining interfering matrix compounds. Typical recoveries when stored at −70°C were in-between 55–97% except for (LTE₄) which was found to be around 40% after 72 days of storage. Seven reversed-phase packings were studied. Selectivity factors, as well as the separation efficiencies, were found to differ for the various C₁₈ bonded silica stationary phases. This integrated on-line column liquid chromatographic system was applied to the determination of leukotriene B₄, leukotriene C₄, leukotriene D₄, leukotriene and E₄ in human cell extracts using prostaglandin B₂ as the internal standard. More than 1500 biological samples were analysed. Some validation data are presented for unattended operations.     

Selective separation behavior of silica gel for zirconium in simulated high level radioactive liquid waste

Zirconium in simulated high level radioactive liquid waste (HLLW) was selectively adsorbed and separated by self-made high adsorption activity silica gel. The selective adsorption mechanism was analyzed according to the structure character of self-made silica gel and performance of zirconium in acid simulated HLLW. The results show that the adsorption selectivity of self-made silica gel for zirconium is strong, because zirconium has higher positive charge and zirconium ion hydrolyzes easily. Distribution coefficient of self-made silica gels for zirconium is 53.5 ml/g. There are 6.5 (OH)/nm² on the surface on self-made silica gels which provide more adsorption activity places, thus self-made silica gels have higher adsorption capacity for zirconium (31.4 mg/g). The elution rate of the adsorption of zirconium on self-made silica gel by 0.2 mol/l H₂C₂O₄ is more than 99%. The solubility of the self-made silica gel in nitric acid is low, the chemical stability of self-made silica gel is very strong.     

Determination of cadmium in water by ICP-AES with on-line adsorption preconcentration using DPTH-gel and TS-gel microcolumns

Two flow injection inductively coupled plasma atomic emission spectrometric methods for the preconcentration and determination of trace amounts of cadmium in sea-water and waste-water samples are described based on the adsorption of the metal ion on a micro-column placed in the injection valve of the FI manifold and packed with silica gel funtionalised with 1,5-bis(di-2-pyridyl) methylene thiocarbohydrazide (DPTH-gel) and silica gel functionalised with methylthiosalicylate (TS-gel), respectively. Various parameters and chemical variables affecting the preconcentration and determination of this metal by ICP-AES are evaluated. The DPTH-gel preconcentration method has a linear calibration range from 5 to at least 100 ng ml(-1) of cadmium, with a R.S.D. of 1.1% for ten independent analyses of 100 ng ml(-1), a detection limit of 1.1 ng ml(-1) and a throughput of 40 samples per hour using a 60 s preconcentration time. The TS-gel preconcentration method shows a linear range between 10 and 100 ng ml(-1), with a R.S.D. of 2.5% for ten independent analyses of 100 ng ml(-1), a detection limit of 4.3 ng ml(-1) and a sample throughput of 24 samples per hour for a preconcentration time of 120 s. Validation was carried out against a certified reference water sample and by determining the analyte content in spiked synthetic sea-water, sea-water and waste-water.     

On-line SFE-GC for determination of PCBs in human milk and blood serum

On-line coupled supercritical fluid extraction and gas chromatography (SFE-GC) has been utilized for the determination of PCBs and other organochlorine compounds in human milk and blood serum. The procedure involved preconcentration of the sample on C₁₈-silica sorbent in an extraction cell: after precipitation of the proteins up to 20 ml of human milk was concentrated on 0.5 g of sorbent. Serum (up to 5 ml) was applied to the C₁₈ material without pretreatment. Basic alumina was utilized as a selective adsorbent for lipids in the on-line SFE-GC system. The method was used to analyze milk and serum spiked with 0.5 and 10 ng of Aroclor 1260 and the results compared with those obtained by liquid–liquid extraction of serum.     

Extraction of uranium by amine, amide and benzamide grafted covalently on silica gel

Organic complexing moieties such as amine, 2°-amide and benzamide functional groups were covalently linked to silica gel by performing organomodification on commercially available silica gel. The extraction of uranium as a function of pH, time, concentration of uranium and the effect of ions such as Fe²⁺, Co²⁺, Ni²⁺ and CO₃ ^2- on the distribution coefficient of uranium by sorbent was studied. The data was fitted into Langmuir adsorption isotherm. The selectivity of the sorbents towards uranium were found to decrease in the order gel-amine >> gel-benzamide ≅ gel-2°-amide at all pHs. The presence of metal ions such as Fe²⁺, Co²⁺, Ni²⁺ and CO₃ ^2- were found to decrease the distribution coefficients (K _d, ml/g) of uranium and the decrease was very high when Fe²⁺ was present. The performance of the sorbent, gel-amine, under a given column condition was tested by following the breakthrough curve of uranium up to C/C ₀ = 0.025. The sorbent was found to be good for the quantitative pre-concentration of uranium from a large amount of sodium. This revised version was published online in July 2006 with corrections to the Cover Date.     

Determination of cadmium, lead and copper in water samples by flame atomic-absorption spectrometry with preconcentration by flow-injection on-line sorbent extraction

Cadmium, lead and copper were determined in synthetic sea-water, drinking water and the NBS 1643b Trace Elements in Water standard reference material at mug/l. levels by flame atomic-absorption spectrometry after on-line preconcentration by sorbent extraction with a flow-injection system. Bonded silica with octadecyl functional groups packed in a micro column of 100 mul capacity was used to collect diethylammonium diethyldithiocarbamate complexes of the heavy metals in the aqueous samples. The sample loading time was 20 sec at a flow-rate of 3.3 ml/min. Ethanol or methanol was used to elute the adsorbed analytes into the spectrometer. The sample loading rate, elution rate and pH were optimized. Enrichment factors of 19-25 for Cd, Pb and Cu were achieved at sampling frequencies of 120/hr with precisions of 1.4, 1.0 and 1.3% rsd (n = 11), respectively. The detection limits (3sigma) for Cd, Pb and Cu were 0.3, 3 and 0.2 mug/l., respectively. Determination of Cd, Pb and Cu in NBS SRM 1643b showed good agreement with the certified values. Recoveries of Cd and Pb added to sea-water were 95 and 102%, respectively.     

Determination of Lead in Heavy Oil by Flow Injection-Flame Atomic Absorption Spectrometry

A simple on-line flow injection analysis pre-concentration technique has been developed. The flow injection system consisted of a 4-channel peristaltic pump, two 6-way rotary injection valves containing a microcolumn of Chelex-100 resin, and a flame atomic absorption spectrometer, allowing the determination of lead at a concentration as low as ppb. The degree of pre-concentration depended on the injected sample volume. Lead contained in NBS 1634b and other heavy oil samples was determined using the system. Samples were ashed directly in a furnace at 550°C for two hours, dissolved with perchloric acid and then injected into the system. The sampling frequency also depended on the injected sample volume.