Response Time Analysis of a Few Selected Tapered Porous Clad Fiber Gas Sensors

A comparative study has been carried out on the detection of gases with the use of attenuated total internal reflection spectroscopy in a multimode step index, based on parabolic, linear, and exponential-linear tapered fibers with porous cladding. Using geometric optics, an expression has been derived for the time dependent evanescent absorbance as the gas diffuses through the cladding. It has been shown that the relative evanescent absorbance depends on the taper profile and taper ratio. For a given taper profile, as the taper ratio increases, the response time of the sensor decreases. Further, the sensor with the exponential-linear taper profile has less response time than those with the parabolic and linear profiles in cases of a particular taper ratio.     

Refractometer based on a tapered Mach–Zehnder interferometer with Peanut-Shape structure

A novel refractometer based on tapered Mach–Zehnder modal interferometer (MZI) is proposed and experimentally demonstrated. This sensor is composed of a pair of Peanut-Shape structures and an embedded taper – the former excites high-order cladding modes, while the latter enhances the evanescent field. As the effective refractive index (RI) of cladding is based on the changes of surrounding RI, thus extinction ratio will change due to the alteration of the distribution of power in the fiber which is induced by various differences of core and cladding for RI. As a result, the maximum RI sensitivity of 240.78 extinction ratio/RIU (refractive index unit) is achieved within the range from 1.3334 to 1.4081.     

Fiber-optic evanescent field absorption sensor: A theoretical evaluation

A comparative study of the fiber-optic evanescent field absorption sensors based on parabolic, linear, and exponential-linear taper profiles has been carried out. The expressions for the effective evanescent absorption coefficient of the fluid have been derived for a diffuse source as well as a collimated source-microscope objective combination. It has been shown that the sensitivity of the sensor depends on the taper profile and the type of the source used in addition to the numerical aperture of the fiber and the refractive index of the fluid. For a given taper profile, the sensitivity is more in the case of the collimated source-microscope objective combination as compared to the diffuse source illumination. Further, the sensor with the exponential-linear taper profile is more sensitive than those having parabolic and linear profiles in the case of both sources.     

Fiber-optic evanescent field absorption sensor: A theoretical evaluation

Abstract

A comparative study of the fiber-optic evanescent field absorption sensors based on parabolic, linear, and exponential-linear taper profiles has been carried out. The expressions for the effective evanescent absorption coefficient of the fluid have been derived for a diffuse source as well as a collimated source–microscope objective combination. It has been shown that the sensitivity of the sensor depends on the taper profile and the type of the source used in addition to the numerical aperture of the fiber and the refractive index of the fluid. For a given taper profile, the sensitivity is more in the case of the collimated source–microscope objective combination as compared to the diffuse source illumination. Further, the sensor with the exponential-linear taper profile is more sensitive than those having parabolic and linear profiles in the case of both sources.     

Experimental Studies on the Response of the Fiber Optic Evanescent Field Absorption Sensor

In the present study the response of the fiber optic evanescent field absorption sensor has been analyzed experimentally. The dependence of evanescent absorbance on sample (dye) concentration has been found to be nonlinear, in contradiction to theoretical predictions. The amount of nonlinearity as well as evanescent absorbance has been found to depend on the pH of the sample. As the pH decreases, the amount of nonlinearity and evanescent absorbance decrease. It has been shown that the nonlinearity and high evanescent absorbance at high pH value occur because of the adsorption of the positively charged dye molecules on the surface of the silica core of the plastic-clad silica (PCS) fiber, which is generally used for the sensor. A linear response has been obtained at pH close to 2.0, at which the presence of a tremendous amount of H ions in the sample restricts the adsorption of the dye molecules. The following empirical relation has been found to fit the experimental data: gamma 1.1C 1.6(pH)32C 1 3, where gamma is the evanescent absorption coefficient and C is the concentration of the dye. The first term is due to the simple Beer's law while the second term is the contribution of the pH dependent dye adsorption. In addition, we have found that the increase in core diameter increases the contribution of adsorption.     

An effective attenuation coefficient for evanescent wave spectroscopy using multimode fiber

An attenuation coefficient for evanescent wave spectroscopy on the core of a multimode step index fiber in contact with an absorbing species is derived in terms of the range of incident angles of the meridional rays to the interface. An expression, for the fractional power outside the core as a function of incident angles is also given. Their ratio is discussed for the case of a fiber sensor having a porous cladding in contact with a gaseous absorbing species and one in which a section of cladding has been removed and replaced by an absorbing liquid.     

Fiber-optic sensor based on evanescent wave absorbance around 2.7 μm for determining water content in polar organic solvents

The feasibility of sapphire fiber-optic sensors based on evanescent wave absorption spectroscopy in the infrared range for quantitative determination of water content in polar organic solvents has been investigated. Evanescent wave absorption spectra of sapphire fiber-optic sensors in glycerol, ethanol, and glycol with different water concentrations obtained and analyzed, respectively. Evanescent absorbance of the sensors in those organic solvents has been utilized to implement for in situ monitoring water concentration in organic solvents. The evanescent absorbance of sensors in glycerol and glycol has been found to vary linearly with water content in the range 0–30 % and in ethanol in the range 0–10 %, respectively. The fiber-optic sensors based on evanescent absorbance for monitoring water concentrations in those organic solvents are acceptably accurate, cost-effective, and reliable. Some methods to improve the accuracy of predicated water content in those organic solvents are also suggested. Overall, the results demonstrate that the sapphire fiber-optic sensor based on evanescent absorption spectroscopy is a promising candidate for prediction of water content in polar organic solvents in on-line and remote situation.     

Efficient evanescent coupling design for GeSi electro-absorption modulator

Efficient coupling from the silicon waveguide to the GeSi layer is the key to success in the GeSi electro-absorption （EA） modulator based on evanescent coupling. A lateral taper in the upper GeSi layer has room for increasing the modulating efficiency and alleviating the sensitivity of the extinction ratio （ER） and insertion loss （IL） to the length of the active region. The light behavior and the effect of the taper are explored in detail using the beam propagation method （BPM）. After optimization, the light can nearly be totally confined in the GeSi layer without any oscillation. The modulator with the designed taper can achieve low IL and high ER.     

光纤倏逝波型石英增强光声光谱技术

采用块状光学准直聚焦透镜组的传统石英增强光声光谱(QEPAS)技术存在体积难以缩减,结构稳定性不佳,无法适应空间狭小、振动复杂的特殊环境等缺点.基于此,将光纤倏逝波技术与QEPAS技术相结合,提出了一种新型微纳结构光纤QEPAS痕量气体检测技术.实验中,为了提高QEPAS系统信号幅值,优化了石英音叉与激光束的空间位置、激光波长调制深度,同时对比了两种不同共振频率的石英音叉,最终采用共振频率较低的30.720 kHz石英音叉作为声波探测元件,获得的检测极限为6.25×10~(-4)(体积分数),归一化噪声等效吸收系数为4.18×10~(-7)cm~(-1).W·Hz~(-1/2).     

空芯带隙型光子晶体光纤整体空气孔包层导光特性研究

 传统光纤包层中仅存在泄漏的倏逝波,能量较小,不利于包层传感的应用。增大包层中的能量,实现整体包层导光是提高光纤传感灵敏度的有效途径。从理论上分析了利用空芯带隙型光子晶体光纤(HC-PCF)包层进行导光的机理。在实验上选用带隙外的冷光源和激光对一种典型结构的HC-PCF进行了空气孔包层的导光实验,并利用折射率引导型光子晶体光纤和单模光纤进行对比实验。结果表明,带隙范围外光波在HC-PCF中传输时将不受禁带效应的约束泄露至包层中重新分布。包层中SiO2与空气孔的周期型结构将光波约束在高折射率介质中,实现HC-PCF整体空气孔包层中光波的稳定传输。PBG-PCF包层的整体导光在传感上有提高灵敏度的潜在价值。     

Compact and broadband waveguide taper based on partial bandgap photonic crystals

Partial bandgap characteristics of parallelogram lattice photonic crystals are proposed to suppress the radiation modes in a compact dielectric waveguide taper so as to obtain high transmittance in a large wavelength range. Band structure of the photonic crystals shows that there exists a partial bandgap, The photonie crystals with partial bandgap are then used as the cladding of a waveguide taper to reduce the radiation loss efficiently. In comparison with the conventional dielectric taper and the complete bandgap photonic crystal taper, the partial bandgap photonic crystal taper has a high transmittance of above 85% with a wide band of 170 nm.     

Influence of tapering process on changes of optical fiber refractive index distribution along a structure

Investigations of internal structure changes along an optical fiber during the manufacture of biconical taper have been described. Basing on the constant volume theory, classification of biconical structures manufactured on a special set-up is presented and discussed. The interferometric tomography method has been used for determination of 3D geometry and refractive index distribution in manufactured optical fiber tapers. The experiments provide detailed information on external (diameter of cladding) as well as internal (core diameter and refractive index profile) changes along the taper region. The results have been discussed in relation to the parameters of the manufacturing process.     

A rigorous analysis of the distribution of power in plastic clad linear tapered fibers

An analytical investigation is presented of the propagation of power in a step-index plastic clad tapered optical fiber operating in the infrared region of the electromagnetic (EM) spectrum. The chosen materials are widely used in low cost optical links. It is assumed that the taper section has a linear profile. Following rigorous analytical approach, the general expressions for power in the core and the cladding sections are derived, and a study is presented of the variation of the relative power along the propagation direction in respect of different (meriodinal and skew) lower order modes. It is observed that, in general, the confinement of power is fairly high in the core section, and the confinement increases with the increase in the taper length and/or mode index. In the cladding region, the confinement decreases for higher taper lengths.     

Designing of Optical Fiber Sensing Probe

Evanescent wave configuration has been extensively used in the development of fiber-optic sensor for different biomedical applications. In the present investigation we have theoretically proposed the designing of single-mode and multimode optical fiber sensing probes, which can be prepared by removing a few centimeters of cladding near the distal end of the step index optical fiber. In this theoretical study, we found that the removal of cladding causes V-number mismatching and this has led to the loss of signal acquisition from the sensing region. Therefore, to minimize these losses we have proposed to reduce the radius by step etch and tapering technique. It was found that step etching and tapering enhances the strength and penetration depth of the evanescent wave significantly.     

利用导波耦合角度实时控制光刻胶光栅掩模的占宽比

研究一种控制多层介质膜上的光刻胶光栅掩模占宽比(线宽与周期之比)的新方法。该方法基于下面的原理:如果某泄漏模在包层中的隐失尾较强,那么它的等效折射率受光刻胶光栅占宽比变化的影响就大,从而可以利用耦合角度来实时控制光栅占宽比。在光栅制作的显影阶段,采用实时监测技术,根据耦合角度和占宽比之间的关系预设入射光角度,在出现共振反常的时刻停止显影来控制占宽比。实验结果表明,固定适当的入射角度可以得到特定的占宽比;改变入射角度,占宽比按照预计的规律变化,因此定性地验证了这种占宽比控制方法的可行性。文中给出了监控装置和具体的实验方法,并讨论了误差来源和影响。     

Propagation characteristics of the silica and silicon subwavelength-diameter hollow wire waveguides

The basic propagation properties of the silica and silicon subwavelength-diameter hollow wire waveguides have been investigated by comparison. It shows that the silica and silicon subwavelength-diameter hollow wire waveguides have some interesting properties, such as enhanced evanescent field in the cladding, enhanced intensity in the hollow core, and large waveguide dispersion. For the different confinement ability, the enhanced field in the hollow core and cladding of the silica subwavelength-diameter hollow wire is much stronger than that of the silicon one for the same size.     

基于薄芯光纤模态干涉技术的折射率 传感特性实验研究

报道了一种具有微结构缺陷的折射率传感器,并对其折射率特性进行了实验研究.将一部分薄芯光纤熔接于标准单模光纤中,由于插入的薄芯光纤和单模光纤纤芯失配,导致包层的高次模被激发并与纤芯模在单模光纤内形成干涉仪.通过减小薄芯光纤的包层直径,以增强包层中的传输模在环境中的倏逝场,从而提高对环境折射率测量的灵敏度.实验表明,该折射率传感器具有损耗低、成本低、灵敏度高和线性度好等特点.     

Designing of Optical Fiber Sensing Probe

Evanescent wave configuration has been extensively used in the development of fiber-optic sensor for different biomedical applications. In the present investigation we have theoretically proposed the designing of single-mode and multimode optical fiber sensing probes, which can be prepared by removing a few centimeters of cladding near the distal end of the step index optical fiber. In this theoretical study, we found that the removal of cladding causes V-number mismatching and this has led to the loss of signal acquisition from the sensing region. Therefore, to minimize these losses we have proposed to reduce the radius by step etch and tapering technique. It was found that step etching and tapering enhances the strength and penetration depth of the evanescent wave significantly.     

Cladding index modulated fiber grating

A new type of fiber grating with only cladding index modulation is presented. Characteristics of both cladding index modulated short-period fiber grating (FBG) and long-period fiber grating (LPFG) are analyzed. The calculation of the modes involved in this paper is based on a model of three-layer step-index fiber geometry. Transmission of a mode guided by the core through a cladding index modulated grating when evanescent field coupling occurs is analyzed with couple-mode theory. Evanescent field coupling causes a power flowing from the core to the cladding, so the attenuation of the new grating is analyzed as well. Lower attenuation, flexible spectral characteristics are demonstrated in comparison with traditional fiber core index modulated grating.     

A novel probe for an evanescent wave fibre-optic absorption sensor

A novel, highly sensitive probe consisting of a uniform region sandwiched between two linear tapers for an evanescent wave fibre-optic absorption sensor is proposed. The diameter of the uniform region is chosen to be equal to the minimum allowed diameter of the taper's output end. The first taper is used to bring the angles of the rays in the input fibre close to the critical angle of the sensing region while the second taper reconverts the angles into their initial values so that they can propagate in the output fibre. It has been shown that the sensitivity of the sensor depends on the length of the uniform region of the probe, the refractive index of the fluid and the numerical aperture of the fibre. The sensitivity increases with increase in the length of the uniform region and also with decrease in the numerical aperture of the fibre. In addition, the sensitivity of the proposed probe can be further increased by launching the selected rays into the input fibre.