Dual-phase solid polymer electrolytes prepared from styrene–butadiene copolymer latices

A new dual-phase solid polymer electrolyte system has been proposed. In this system, a network of ion pathways is formed in a low-polarity, host polymer matrix. A series of electrolytes were prepared from styrene-butadiene copolymer latices with dissolved lithium salts. Polymer films were formed from these latices, and then impregnated with γ-butyrolactone (γ-BL) or γ-butyrolactone/dimethoxyethane mixture (γ-BL/DME), giving latex polymer electrolytes. The ionic conductivity of the polymer electrolyte system increased with increasing solvent content, although a distinct percolation threshold was not measured. Ionic conductivity also increased with the use of DME cosolvent, with the highest conductivity being 1.4 × 10^?4S/cm. Complex impedance diagrams are discussed. The diagrams show significant deviations from the ideal. TEM/SEM observations are consistent with the desired dual-phase morphology. © 1993 John Wiley & Sons, Inc.     

Dual-Phase structure of polymer electrolytes comprised of NBR/SBR latex films swollen with lithium salt solution

Dual-phase polymer electrolytes (DPE) that have high ionic conductivity (> 10^?3 S/cm) and good mechanical strength were prepared by mixing NBR and SBR latices and casting films. The latex films absorbed large quantities of lithium salt solution (e.g., 1M lithium perchlorate in γ-butyrolactone) to obtain DPE films but did not dissolve with swelling. The NBR phase is polar and was impregnated selectively with the polar lithium salt solution, whereas the SBR phase is nonpolar and formed a mechanically-supportive matrix. Transmission electron microscopic (TEM), electron energy loss spectral (EELS), and energy-dispersive x-ray (EDX) analyses showed microscopically the dual-phase structure. Evidence for swelling by lithium salt solution was found only in the NBR phase and not in the SBR phase by EDX microanalysis. Ionic conductivity as a function of NBR content or swelling degree showed clearly that a percolation threshold for ionic conductivity exists. © 1994 John Wiley & Sons, Inc.     

Synthesis of ion-free latex particles composed of polybutadiene and poly (vinyl pyrrolidone) as polymer electrolyte materials

The synthesis of polybutadiene (PB) by emulsion polymerization with use of poly (vinyl pyrrolidone) (PVP) stabilizer was investigated. The goal was to prepare flexible latex films that clearly retain particle morphology in the solid state after heat treatment and contain no ionic, hydroxyl, or (primary, secondary) amino groups. The latex particle core composed of PB was nonpolar and rubbery, while the particle shell composed of PVP was polar and glassy. Average particle diameter was measured by the dynamic light scattering technique, and particles were imaged by scanning and transmission electron microscopic analyses. Dialysis of the latices resulted in successful exchange of the dispersion medium without precipitation. © 1994 John Wiley & Sons, Inc.     

Polymeric surfactants in latex technology: polystyrene–poly(ethylene oxide) block copolymers as stabilizers in emulsion polymerization

Polystyrene–poly(ethylene oxide) PS–PEO di- and triblock copolymers have been used as stabilizers in the emulsion polymerization of styrene and styrene–butylacrylate for the preparation of “hairy latexes”. The polymerization kinetics and the efficiency of these polymeric surfactants were correlated with the molecular characteristics of the block copolymer. It was shown that the efficiency decreased with increasing molecular weight and PS content of the block copolymer. The PEO frige, with a thickness of 4–25 nm, on the latex particle surface could be characterized and it was shown by differential scanning calorimetry (DSC) that water is strucured in that PEO layer. Film formation with “hairy latexes” was also examined both by DSC and thermomechanical analysis. The properties and application possibilities, such as in controlled latex flocculation, have been reviewed.     

Ion-free latex films composed of fused polybutadiene and poly (vinyl pyrrolidone) particles as polymer electrolyte materials

Latex films composed of fused polybutadiene (PB) and poly (vinyl pyrrolidone) (PVP) particles that contain no ionic, hydroxyl, or amino groups were swelled with lithium salt solutions to yield new polymer electrolyte materials. The latex particle consists of a nonpolar, rubbery core that contains the PB component and a polar, glassy shell that contains the PVP component. The particle core-shell morphology was retained in the solid state, after the latex dispersion medium was removed and the films dried at high temperatures, due to the high T_g of the PVP shell. The films swelled when immersed in lithium salt solutions, and ionic conductivity of swollen films was greater than 10^-3 S/cm. Swelling and ionic conduction occurred only in the polar PVP component. Extraction of PVP occurred with extended swelling. © 1994 John Wiley & Sons, Inc.     

Effect of unmodified kraft lignin concentration on the emulsion and miniemulsion copolymerization of styrene with n‐butyl acrylate and methacrylic acid to produce polymer hybrid latex

The introduction of non‐modified kraft LignoBoost® lignin (KL) to produce polymer hybrid latex has received much attention in recent years because it is derived from renewable resources. The focus of this work is to develop a polymer hybrid latex by emulsion and miniemulsion copolymerization of styrene with n‐butyl acrylate and methacrylic acid in the presence of different concentrations of KL furnished by the pulp and paper industry. The study intends to substitute a styrene in the system to understand the effect of non‐modified KL on the properties not only of the latexes, but also on the copolymers themselves. Each polymerization was carried out by shot‐process of tertbutyl hydroperoxide and sodium formaldehyde sulfoxylate as the redox system. The polymer latexes were characterized in relation to overall conversion, particle diameter, particle morphology, coagulum formation, surface tension, zeta potential, and atomic force microscopy. The polymers were evaluated through gel permeation chromatography, water absorption, and thermal properties. The results show that the addition of non‐modified KL results in inhibition of the polymerization and that KL acts as a colloid stabilizer. Small particles were generated in the initial stages of the polymerizations. The presence of the KL altered the color of the latexes; the increase in KL concentration resulted in increase in the absorption of water of the polymer films; the increase in KL concentration resulted in decrease of the molar mass of the copolymers.     

Synthesis and properties of soap-free poly(methyl methacrylate-ethyl acrylate-methacrylic acid) latex particles prepared by seeded emulsion polymerization

In order to obtain functional polymer latex particles with clean surface and with surface carboxyl groups, P(MMA-EA) seed particles with the diameter of 335 nm were first synthesized via soap-free batch emulsion polymerization of methyl methacrylate (MMA) and ethyl acrylate (EA), and then the seeded emulsion copolymerization of MMA, EA and MAA (methacrylic acid) onto the seed particles were performed in the absence of emulsifier. Influences of ingredients and conditions on polymerization, latex particle size (D_p) and its distribution were investigated. Results showed that most of the monomers polymerized onto the seed latex particles in the second step of polymerization by using drop-wise addition method, and D_p increased from 483 nm to 829 nm with the mass ratio of core/shell monomers [C]/[S] decreased from 1:2 to 1:15. It was found that D_p decreased with the increase of MAA and initiator amounts, and the size of the latex particles became uniform with the decrease of MAA amount and with the increase of [C]/[S] value.     

Synthesis and characterization of poly (n-butyl acrylate)-poly (methyl methacrylate) latex interpenetrating polymer networks by radiation-induced seeded emulsion polymerization

A series of latex interpenetrating polymer networks (LIPNs) were prepared via a two-stage emulsion polymerization of methyl methacrylate (MMA) or mixture of MMA and n-butyl acrylate (n-BA) on crosslinked poly(n-butyl acrylate)(PBA) seed latex using ⁶⁰Co γ-ray radiation. The particles of resultant latex were produced with diameters between 150 and 250 nm. FTIR spectra identified the formation of crosslinked copolymers of PMMA or P(MMA-co-BA). Dynamic light scattering (DLS) showed that with increasing n-BA concentration in second-stage monomers, the particle size of LIPN increased. Transmission electron microscope(TEM) photographs showed that the morphology of resultant acrylate interpenetrating polymer network (IPN) latex varied from the distinct core-shell structure to homogenous particle structure with the increase of n-BA concentration, and the morphology was mainly controlled by the miscibility between crosslinked PBA seed and second-stage copolymers and polarity of P(MMA-co-BA)copolymers. In addition, differential scanning calorimeter (DSC) measurements indicated the existence of reinforced miscibility between PBA seed and P(MMA-co-BA)copolymer in prepared LIPNs.     

Poly(vinyl acetate‐co‐dibutyl maleate) latex films in the presence of grafted and post‐added poly(vinyl alcohol)

We describe the synthesis and characterization of a series of poly(vinyl acetate‐co‐dibutyl maleate) [P(VAc‐DBM)] latex particles (monomer molar ratio 10.6:1). One set of samples [high‐M and M_250k SDS‐P(VAc‐DBM), gel content 50% and 0%] was prepared in the presence of an anionic surfactant sodium dodecyl sulfate. The other two sets of samples [high‐M and M_250k PVOH–P(VAc‐DBM)] were prepared in the presence of poly(vinyl alcohol) (PVOH). These polymers differ in gel content (50 and 0%) and the extent of PVOH grafting (30 and 15%). Polymer diffusion across cell boundaries in the latex films was monitored by fluorescence resonant energy transfer (ET) experiments. First, we examined M_250k samples in the presence of grafted and post‐added PVOH. The presence of post‐added PVOH (5%) causes a small but detectable retardation on the rate of polymer diffusion, whereas the presence of grafted PVOH (degree of grafting: 15%) significantly promotes the polymer diffusion rate. For the high‐M P(VAc‐DBM), the presence of post‐added PVOH also retards the polymer diffusion. Strikingly, the presence of grafted PVOH (degree of grafting: 30%) in the high‐M PVOH‐P(VAc‐DBM) promotes the polymer diffusion to such an extent that the diffusion was complete in the freshly prepared films. Our data also suggest that under our experimental conditions, the rate of P(VAc‐DBM) diffusion increases with an increase of the degree of PVOH grafting. To confirm these results, we carried out fluorescence microscopy experiments to monitor the fate of PVOH in these latex films and found that in newly formed PVOH–P(VAc‐DBM) films, the PVOH was either uniformly distributed in the P(VAc‐DBM) matrix or the domains were too small to be resolved (i.e., < 0.5 μm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5005–5020, 2004     

Ab initio RAFT emulsion polymerization of butadiene using the amphiphilic poly(acrylic acid‐b‐styrene) trithiocarbonate as both surfactant and mediator

Ab initio reversible addition fragmentation chain transfer (RAFT) emulsion polymerization of butadiene was investigated by using the amphiphilic poly(acrylic acid_n‐b‐styrene₅) trithiocarbonate as both surfactant and mediator. The neutralization on acrylic acid (AA) units played significant influence on the gelation. When half of the AA units were neutralized, the gelation occurred in the early stage of the polymerization so that the highest accessible molecular weight of polybutadiene was as low as 5 kg mol^?1. In the non‐neutralized conditions, the gelation was much retarded so that the highest accessible molecular weight was increased up to 23 kg mol^?1. In the non‐neutralized conditions, potassium persulfate could not initiate the polymerization. When azobisisobutyronitrile was used as initiator, the polymerization mediated by poly(acrylic acid₂₇‐b‐styrene₅) trithiocarbonate could proceed much faster than the solution polymerization did. The latex was stable. Before the gel point, molecular weight agreed well with the theoretical prediction while PDI was relatively high due to the branching reaction. The poly(butadiene‐b‐styrene) core/shell particles could obtained by extending polybutadiene. When the n value in poly (acrylic acid_n‐b‐styrene₅) trithiocarbonate was lower than 20, the coalescence would occur, leading to the formation of some coagulum. On the other hand, when n value was as high as 60, the molecular weight was out of control. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and morphology of Fe3O4/polystyrene/poly(isopropylacrylamide‐co‐methyl acrylate acid) magnetic composite latex – 2,2′‐azobis (2‐methylpropionamidine) dihydrochloride as initiator

In this work, Fe₃O₄/polystyrene/poly(N‐isopropylacryl amide‐co‐methylacrylate acid) (Fe₃O₄/PS/P(NIPAAM‐co‐MAA)) magnetic composite latex was synthesized by the method of two stage emulsion polymerization. In this reaction system, 2,2′‐azobis(2‐methyl propionamidine) dihydrochloride (AIBA) was used as initiator to initiate the first stage reaction and second stage reaction. The Fe₃O₄ particles were prepared by a traditional coprecipitation method. Fe₃O₄ particles were surface treated by either PAA oligomer or lauric acid to form the stable ferrofluid. The first stage for the synthesis of magnetic composite latex was to synthesize PS in the presence of ferrofluid by soapless emulsion polymerization to form the Fe₃O₄/PS composite latex particles. Following the first stage of reaction, the second stage of polymerization was carried out by the method of soapless emulsion polymerization with NIPAAM and MAA as monomers and Fe₃O₄/PS latex as seeds. The magnetic composite particles, Fe₃O₄/PS/P(NIPAAM‐co‐MAA), were thus obtained. The mechanism of the first stage reaction and second stage reaction were investigated. Moreover, the effects of PAA and lauric acid on the reaction kinetics, morphology, and particle size distribution were studied. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3912–3921, 2007     

Synthesis of an alkali‐swellable emulsion and its effect on the rate of polymer diffusion in poly(vinyl acetate‐butyl acrylate) latex films

We describe the synthesis and characterization of a weakly cross‐linked poly(methacrylic acid‐co‐ethyl acrylate) alkali‐swellable emulsion (ASE), as well as an investigation of its influence on the rate of polymer diffusion in latex films. The films examined were formed from poly(vinyl acetate‐co‐butyl acrylate) latex particles containing a small amount of acrylic acid as a comonomer. Polymer diffusion rates were monitored by the energy transfer technique. We found that the presence of the ASE component, either in the acid form or fully neutralized by ammonia or sodium hydroxide, had very little effect on the polymer diffusion rate. However, in the presence of 2 wt % NH₄‐ASE, there was a small but significant increase in the polymer diffusion rate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5632–5642, 2005     

Ionic interaction behavior and facilitated olefin transport in poly(n‐vinyl pyrrolidone):Silver triflate electrolytes; Effect of molecular weight

Interactions of cation/anion and cation/polymer in poly(N‐vinyl pyrrolidone) (PVP):silver triflate (AgCF₃SO₃) electrolytes with different weight‐average molecular weights (M_w's) of 1 × 10⁶ (1 M), 3.6 × 10⁵ (360 K), 4 × 10⁴ (40 K), and 1 × 10⁴ (10 K) have been studied with IR and Raman spectroscopies. According to the change of the C?O peak, coordination of silver ions by C?O in a low M_w (10 or 40 K) PVP matrix tend to be always thermodynamically favorable than high M_w (1 M or 360 K) PVP, demonstrating that the polymer matrix of low M_w dissolves silver salts more effectively. In addition, silver cations interact with both larger SO and smaller CF₃ to form ion pairs, and the former interaction is stronger than the latter in a monomer or low M_w polymer matrix (40 K, 10 K), as demonstrated by theoretical ab initio calculation or experimental spectroscopy, respectively. However, CF₃ interacts more favorably with silver cation than SO in high M_w (1 M and 360 K) PVP, which is ascribed to the steric effect of the bulky SO anion by highly entangled polymer chains. Despite the superior dissolving property of the low M_w polymer matrix, the membranes consisting of low M_w PVP and AgCF₃SO₃ exhibited poor separation performance for propylene/propane mixtures in comparison with those of high M_w, presumably because of the poor mechanical property for membrane formation in low M_w PVP. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1813–1820, 2002     

Block copolymers prepared by emulsion polymerization with poly(ethylene oxide)–azo-initiators

Poly(ethylene oxide)-b-poly(styrene) block copolymers were prepared in the form of latex particles by emulsion polymerization of styrene with poly(ethylene glycol)–azo-initiators as well as with the redox initiation system poly(ethylene glycol)/Ce⁴⁺. The emulsion polymerization can be carried out in the absence of additional stabilizers if the chain length of the poly(ethylene glycol) is greater than 40. The latex particles as well as the copolymers were characterized by capillary hydrodynamic fractionation, ¹³C-nuclear magnetic resonance (NMR) spectroscopy and Fourier transform infrared spectroscopy. By ¹³C-NMR spectroscopy a side reaction of the primary radicals arising from the azo-initiator was found which can contribute to the low efficiency of azo-initiators in emulsion polymerization.     

Synthesis and characterization of fluorine‐containing polyacrylate latex with core–shell structure by UV‐initiated seeded emulsion polymerization

A core–shell fluorine‐containing polyacrylate emulsion was successfully prepared by UV‐initiated seeded emulsion polymerization in two stages in the presence of two photoinitiators. The water‐soluble photoinitiator for the core polymerization and the oil‐soluble photoinitiator was used for the shell polymerization. Both of the two stage polymerizations could be completed within 15 min and displayed a conversion above 94%. The emulsion and the films were characterized by Fourier transformed infrared spectrometry, transmission electron microscopy, dynamic light scattering, X‐ray photoelectron spectroscopy (XPS), contact angle (CA), and thermogravimetry analysis, respectively. The analysis results indicated that the fluorine‐containing latex particles had very small particle size (40 nm) with a core–shell structure and a narrow particle size distribution. XPS analysis revealed that a gradient concentration of fluorine excited in fluorine‐containing emulsion film from the film–air interface to the film–glass interface. In addition, the film formed from the fluorine‐containing emulsion exhibited not only higher thermal stability but also better hydrophobicity than that of the fluorine‐free emulsion. Copyright © 2010 John Wiley & Sons, Ltd.     

Structural changes of silver polymer electrolytes: Comparison between poly(2‐ethyl‐2‐oxazoline) and poly(N‐vinyl pyrrolidone) complexes with silver salt

The difference between the polymer matrices of poly(2‐ethyl‐2‐oxazoline) (POZ) and poly(N‐vinyl pyrrolidone) (PVP) does not have a significant effect on the facilitated propylene transport and propylene solubility in 1:1 polymer/silver salt complex membranes, according to our previous work. In this article, its origin is investigated in terms of both microstructures of silver polymer electrolytes and the coordinative interaction of silver ion with polymer and with the counteranion. Initially different microstructures of POZ and PVP become similar to each other upon dissolving a large amount of silver salt, as evidenced by propane transport properties, specific volume, and Bragg d‐spacing. The dissolution of the silver salt in the polymer solvent strongly depends on the coordinative interaction between silver ion and carbonyl oxygen of POZ and PVP. Thus, the structural similarity upon dissolving silver salts in POZ and PVP is primarily determined by the coordinative interaction between silver ion and carbonyl oxygen, which was confirmed by theoretical structure calculation based on density functional theory and by IR and Raman spectroscopy. Therefore, facilitated olefin transport for silver polymer electrolyte membranes does not strongly depend on the polymeric matrix at high silver concentrations. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 232–237, 2004     

Block copolymers of acrylic acid and butyl acrylate prepared by reversible addition–fragmentation chain transfer polymerization: Synthesis,characterization, and use in emulsion polymerization

Amphiphilic block copolymers of poly(acrylic acid‐b‐butyl acrylate) were prepared by reversible addition–fragmentation chain transfer polymerization in a one‐pot reaction. These copolymers were characterized by NMR, static and dynamic light scattering, tensiometry, and size exclusion chromatography. The aggregation characteristics of the copolymers corresponded to those theoretically predicted for a star micelle. In a butyl acrylate and methyl methacrylate emulsion polymerization, low amounts of these copolymers could stabilize latices with solid contents up to 50%. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 684–698, 2003     

Star-shaped polymers by living cationic polymerization. VII. Amphiphilic graft polymers of vinyl ethers with hydroxyl groups: Synthesis and host–guest interaction

Amphiphilic graft polymers of vinyl ethers (VEs) ( 6 ) where each branch consists of a hydrophilic polyalcohol and a hydrophobic poly(alkyl vinyl ether) segment were prepared on the basis of living cationic polymerization, and their properties and functions were compared with the corresponding amphiphilic star-shaped polymers. In toluene at ?15°C, the HI/ZnI₂-initiated living block polymer 2 of an ester-containing VE (CH₂? CHOCH₂CH₂OCOCH₃) and isobutyl VE (IBVE) was terminated with the diethyl 2-(vinyloxy)ethylmalonate anion [ 3 ; ^ΦC(COOEt)₂CH₂CH₂OCH ? CH₂] ( 2/3 = 1/2 mole ratio) to give a macromonomer ( 4 ), H[CH₂CH(OCH₂CH₂OCOCH₃)] _m-[CH₂CH(OiBu)]_n? C(COOEt)₂CH₂CH₂OCH ? CH₂ (m = 5, n = 15; M?_n = 2600, M?_w/M?_n = 1.13, 1.10 vinyl groups/chain). Subsequently, 4 was homopolymerized with HI/ZnI₂ in toluene at ?15°C. In 3 h, 85% of 4 was consumed and a graft polymer ( 5 ) was obtained [M?_w = 15000, DP_n (for 4 ) = 6]. The apparent M?_w (10,900) of 5 by size-exclusion chromatography (SEC) is smaller than that by light scattering as well as that (18,300) by SEC of the corresponding linear polymer with the almost same molecular weight, indicating the formation of a multi-branched structure. Hydrolysis of the pendant esters in 5 gave the amphiphilic graft polymer 6 where each branch consists of a hydrophilic polyalcohol and a hydrophobic poly(IBVE) segment. The graft polymer 6 was found to interact specifically with small organic molecules (guests) with polar functional groups, and 6 differed in solubility and host-guest interaction from the corresponding star-shaped polymer. © 1993 John Wiley & Sons, Inc.