Synthesis and characterization of aromatic poly(ether sulfone imide)s derived from sulfonyl bis(ether anhydride)s and aromatic diamines

Two sulfonyl group-containing bis(ether anhydride)s, 4,4′-[sulfonylbis(1,4-phenylene)dioxy]diphthalic anhydride ( IV ) and 4,4′-[sulfonylbis(2,6-dimethyl-1,4-phenylene)dioxy]diphthalic anhydride (Me- IV ), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of the bisphenolate ions of 4,4′-sulfonyldiphenol and 4,4′-sulfonylbis(2,6-dimethylphenol) with 4-nitrophthalonitrile in N,N-dimethylformamide (DMF). High-molar-mass aromatic poly(ether sulfone imide)s were synthesized via a conventional two-stage procedure from the bis(ether anhydride)s and various aromatic diamines. The inherent viscosities of the intermediate poly(ether sulfone amic acid)s were in the ranges of 0.30–0.47 dL/g for those from IV and 0.64–1.34 dL/g for those from Me- IV. After thermal imidization, the resulting two series of poly(ether sulfone imide)s had inherent viscosities of 0.25–0.49 and 0.39–1.19 dL/g, respectively. Most of the polyimides showed distinct glass transitions on their differential scanning calorimetry (DSC) curves, and their glass transition temperatures (T_g) were recorded between 223–253 and 252–288°C, respectively. The results of thermogravimetry (TG) revealed that all the poly(ether sulfone imide)s showed no significant weight loss before 400°C. The methyl-substituted polymers showed higher T_g's but lower initial decomposition temperatures and less solubility compared to the corresponding unsubstituted polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1649–1656, 1998     

Heat-Resistant thermosetting polyamide and polymides with styrlpyridine segments derived from 2,2′-(1,4-phenylenedivinylene) bisaminoquinoline

The nitration of quinaldine by fuming nitric and sulfuric acid afforded nitroquinaldine. It was condensed with a half molar amount of 1,4-benzenedicarbaldehyde in the presence of acetic anhydride to yield 2,2′-(1,4-phenylenedivinylene) bisnitroquinoline. The latter was catalytically hydrogenated to the corresponding diamine, PBAQ. The new polyamide and polymides bearing styrylpyridine segments were prepared utilizing PBAQ as starting material. In addition, a model diamide and diimide were synthesized and characterized IR and ¹H-NMR spectroscopy. Inherent viscosities of polymers ranged from 0.31 to 0.60 dl/g. Certain polymer precursors such as a bismaleimide and bisnadimide were synthesized from the reactions of PBAQ with maleic and nadic anhydride, respectively. Their curing behavior was investigated by DTA. Curing of polyamide, polyimides, and polymer precursors at 240°C for 15 h yielded crosslinked polymers. They were stable up to 329–310°C in N₂ or air and afforded a char yield of 67–62% in N₂ at 800°C. © 1994 John Wiley & Sons, Inc.     

Preparation and properties of aromatic polyamides from 1,4-bis(p-carboxyphenoxy)naphthyl and aromatic diamines

A new aromatic dicarboxylic acid, 1,4-bis (p-carboxyphenoxy)naphthyl ( 3 ), was synthesized by the reaction of p-fluorobenzonitrile with 1,4-naphthalenediol, followed by hydrolysis. Aromatic polyamides having inherent viscosities of 1.27–2.22 dL/g were prepared by the triphenyl phosphite activated polycondensation of diacid 3 with various aromatic diamines. Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents including N,N-dimethyl-acetamide (DMAc), N-methyl-2-pyrrolidone (NMP), and m-cresol. Transparent, tough, and flexible films of these polymers could be cast from the DMAc or NMP solutions. The cast films had tensile strengths ranging from 64–104 MPa, elongations-at-break from 6 to 10%, and initial moduli from 1.52 to 2.14 GPa. These polyamides had glass transition temperatures in the range of 195 to 240°C. Almost all polymers were thermally stable up to 400°C, with 10% weight loss being recorded above 480°C in air and nitrogen atmospheres. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2273–2280, 1997     

Synthesis and properties of soluble and light-colored poly(amide-imide-imide)s based on tetraimide-dicarboxylic acid (TIDA) and various aromatic diamines: TIDA from 4,4′-oxydiphthalic anhydride, 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene, and 3-aminobenzoic acid

A new tetraimide-dicarboxylic acid (TIDA) I was synthesized starting from 3-aminobenzoic acid (m-ABA), 4,4′-oxydiphthalic anhydride (ODPA), and 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene (BAFPB) at a 2:2:1 molar ratio in N-methyl-2-pyrrolidone (NMP). A series of organosoluble, light-colored poly(amide-imide-imide)s (PAII, III_a-j) was prepared by triphenyl phosphite-activated polycondensation from the tetraimide-diacid I with various aromatic diamines (II_a-j). All the polymers were readily soluble in a variety of organic solvents such as NMP, N,N-dimethyl acetamide (DMAc), dimethyl sulfoxide, and even in less polar m-cresol and pyridine. Polymer films cast from DMAc had the cutoff wavelengths between 374 and 384 nm and had the b^∗ values in the range of 14.8-30.2. Polymers III_a-j afforded tough, transparent, and flexible films, which had tensile strengths ranging from 87 to 103 MPa, elongations at break from 11% to 37%, and initial moduli from 1.9 to 2.3 GPa. The glass transition temperatures of these polymers were in the range of 242-274 °C. They had 10% weight loss temperature above 526 °C and showed the char yield more than 55% residue at 800 °C in nitrogen.     

Synthesis of aromatic polyamide-imides from N,N′-bis(trimethylsilyl)-substituted aromatic diamines and 4-chloroformylphthalic anhydride

The polymerization of N,N′-bis(trimethylsilyl)-substituted aromatic diamines with 4-chloroformylphthalic anhydride in various solvents at a temperature range between 10 and 70°C afforded polyamide-amic acid trimethylsilyl esters having inherent viscosities of 0.8–1.4 dL/g. Transparent and flexible films of the silylated precursor polymers were obtained by casting directly from the polymer solutions. Desilylation of the silylated polymers with methanol resulted in the formation of the corresponding polyamide-amic acids. Subsequent thermal imidization of the silylated precursor polymers with the elimination of trimethylsilanol afforded yellow, transparent, and tough films of the aromatic polyamide-imides. The thermal conversion of the silylated precursor polymer to polyamide-imide proceeded almost as rapidly as that of the corresponding polyamide-amic acid prepared by a conventional method from the parent aromatic diamine and 4-chloroformylphthalic anhydride.     

Synthesis and characterization of poly(d,l-lactide-co-glycolide) modified by maleic anhydride and 1,4-butanediamine

Bone tissue engineering is sought to apply strategies for bone defects healing biodegradable porous scaffolds without limitations and shortcomings. In this work, we have developed a novel maleic anhydride (MAH) and 1,4-butanediamine modified poly(lactide-co-glycolide) polymer (BMPLGA). The synthesized polymer was characterized by Fourier transform infrared spectrometry (FTIR), Nuclear magnetic resonance spectra (¹H NMR), gel permeation chromatography (GPC) and contact angle measurements. In addition, cell morphologies in the extracts and cell cytotoxity were also studied. The results showed that the BMPLGA was successfully obtained by introducing MAH and 1,4-butanediamine into PLGA in bulk. The introduction of anhydride and amino groups improved the hydrophilicity of PLGA. Fibroblastic cells showed normal morphologies in BMPLGA extracts, and the BMPLGA materials showed no cell cytotoxicity. The synthetic BMPLGA material may have potentials for biomedical applications due to improving hydrophilicity.     

Synthesis and properties of poly(amide-imide)s derived from trimellitic anhydride, ω-amino acids,and aromatic diamines

Seven imidodicarboxylic acids II -1 to 5, II -10, and II -11 were prepared from trimellitic anhydride and ω-amino acids, such as glycine, β-alanine, 4-aminobutyric acid, 5-aminopentanoic acid, 6-aminohexanoic acid, 11-aminoundecanoic acid, and 12-aminododecanoic acid. Several aliphatic-aromatic poly(amide-imide)s were prepared by triphenyl phosphite promoted polycondensation reaction from the combination of 3-(4-carboxyphthalimido)propionic acid ( II -2) or 6-(4-carboxyphtalimido)hexanoic acid ( II -5) with various aromatic diamines and of all the imidodiacids with p-phenylenediamine or 4,4′-oxydianiline. All poly(amide-imide)s were characterized by inherent viscosity, gel permeation chromatography (GPC) measurements, solubility, tensile test, wide-angle X-ray scatting patterns, differential scanning calorimetry (DSC) measurements, and thermogravimetric (TGA) analyses. Effects of structural changes such as polymethylene length and diamine moieties on the properties of poly(amide-imide)s were studied. © 1994 John Wiley & Sons, Inc.     

Synthesis and thermal stability of the resins prepared from the reactions of 1,4-bis(2,2-dicyanovinyl)benzene with aromatic diamines and electrical conductivity of the resulting materials following pyrolysis

New thermosetting resins were prepared from the reaction of 1,4-bis(2,2-dicyanovinyl)benzene with aromatic diamines in varying molar ratios. The thermal stability of these resins was correlated with their composition and the curing conditions. They were stable in N₂ up to 370–448°C and afforded anaerobic char yields of 73–84% at 800°C after curing at 300°C for 20–60 h. The temperature dependence of the electrical resistivity of all resins pyrolyzed at 700°C for 15 h was studied in the temperature range from ?173–327°C (100–600 K). The results showed that at room temperature the unpyrolyzed polymers have insulating properties, whereas a dramatic decrease in the electrical resistivity is observed following pyrolysis. The temperature dependence of the electrical resistivity suggests that all of the materials studied have semiconducting properties. The observed electrical conductivity is thermally activated with activation energies ranging from 0.03–0.06 eV. © 1994 John Wiley & Sons, Inc.     

Synthesis and properties of new polyamides derived from 1,4-bis(4-aminophenoxy)-2,5-di-tert-butylbenzene and aromatic dicarboxylic acids

The diamine 1,4-bis(4-aminophenoxy)-2,5-di-tert-butylbenzene, containing symmetric, bulky di-tert-butyl substituents and a flexible ether unit, was synthesized and used to prepare a series of polyamides by the direct polycondensation with various aromatic dicarboxylic acids in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. All the polymers were obtained in quantitative yields with inherent viscosities of 0.32–1.27 dL g⁻¹. Most of these polyamides, except II _a , II _d , and II _e , showed an amorphous nature and dissolved in polar solvents and less polar solvents. Polyamides derived from 4,4′-sulfonyldibenzoic acid, 4,4′-(hexafluoro-isopropylidene)dibenzoic acid, and 5-nitroisophthalic acid were even soluble in a common organic solvent such as THF. Most polyamide films could be obtained by casting from their N,N-dimethylacetamide (DMAc) solutions. The polyamide films had a tensile strength range of 49–78 MPa, an elongation range at break of 3–5%, and a tensile modulus range of 1.57–2.01 GPa. These polyamides had glass transition temperatures ranging between 253 and 276°C, and 10% mass loss temperatures were recorded in the range 402–466°C in nitrogen atmosphere. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1069–1074, 1998     

Synthesis and properties of polyimides derived from 1,4-bis(4-aminophenoxy)2,5-di-tert-butylbenzene

Novel aromatic polyimides containing symmetric, bulky di-tert-butyl substituents unit were synthesized from 1,4-bis(4-aminophenoxy)2,5-di-tert-butylbenzene (BADTB) and various aromatic tetracarboxylic dianhydrides by the conventional two-stage procedure that included ring-opening polyaddition in a polar solvent such as N,N-dimethylacetamide to give poly(amic acid)s, followed by cyclodehydration to polyimides. The diamine was prepared through the nucleophilic displacement of 2,5-di-tert-butylhydroquinone with p-chloronitrobenzene in the presence of K₂CO₃, followed by catalytic reduction. Depending on the dianhydrides used, the poly(amic acid)s obtained had inherent viscosities of 0.83–1.88 dL g⁻¹. Most of the polyimides formed transparent, flexible, and tough films. Tensile strength and elongation at break of the BADTB-based polyimide films ranged from 68–93 MPa and 7–11%, respectively. The polyimide derived from 4,4′-hexafluoro-isopropylidenebisphathalic anhydride had better solubility than the other polyimides. These polyimides had glass transition temperatures between 242–298°C and 10% mass loss temperatures were recorded in the range of 481–520°C in nitrogen. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1527–1534, 1997     

Synthesis and evaluation of novel polyimides derived from spirobichroman diether anhydride

A spirobichroman structure-containing diether anhydride (SBCDA), 6,6′-bis(3,4-dicarboxyphenoxy)-4,4,4′,4′,7,7′-hexamethyl-2,2′-spirobichroman dianhydride, was prepared by the nucleophilic nitrodisplacement of 4-nitrophthalonitrile with the phenolate ion of 6,6′-dihydroxy-4,4,4′,4′,7,7′-hexamethyl-2,2′-spirobichroman, followed by alkaline hydrolysis of the intermediate tetranitrile and dehydration of the resulting tetraacid. A series of high molecular weight poly(ether imide)s with inherent viscosities between 0.45 and 1.28 dL/g were synthesized from SBCDA and various aromatic diamines via a conventional two-stage procedure that included ring-opening polyaddition in N,N-dimethylacetamide (DMAc) to give poly(amic acid)s, followed by thermal cyclization to poly(ether imide)s. The intermediate poly(amic acid)s had inherent viscosities of 0.70–1.50 dL/g. Except for the poly(ether imide) obtained from p-phenylenediamine, the other poly(ether imide)s were soluble in various organic solvents and could be solution-cast into transparent, flexible, and tough films. These poly(ether imide)s had glass transition temperatures in the range 175–262°C and showed no significant decomposition below 420°C, with 10% weight loss being recorded above 446°C in nitrogen or air. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2801–2809, 1997     

Novel soluble fluorinated aromatic polyamides derived from 2-(4-trifluoromethylphenoxy)terephthaloyl chloride with various aromatic diamines

A series of novel fluorinated aromatic polyamides derived from a new monomer, 2-(4-trifluoromethylphenoxy)terephthaloyl chloride (TFTPC), with various aromatic diamines were synthesized and characterized. The polyamides were obtained in high yields and moderately high inherent viscosities ranging from 1.07 to 1.16 dL/g. All the polyamides were amorphous and readily soluble in many organic solvents, such as N-methyl-2-pyrrolidinone (NMP), N,N′-dimethylacetamide (DMAc), N,N′-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO), and could afford flexible and tough films via solution casting. The cast films exhibited good mechanical properties with tensile strengths of 82.8-107.3 MPa, elongation at break of 4.1-7.2%, and tensile modulus of 2.26-3.95 GPa. These polyamide films also exhibited good thermal stability with the glass transition temperature of 222-294 °C, the temperature at 5% weight loss of 442-472 °C in nitrogen. They exhibited low dielectric constants ranging from 3.25 to 3.39 (1 MHz), low moisture absorption in the range of 1.32-2.45%, high transparency with an ultraviolet-visible absorption cut-off wavelength in the 330-371 nm range, and excellent electrical properties.     

Preparation and spectral characterization of new macrocyclic Ni(II) and Co(II) complexes derived from 1,4- bis (2-carboxyaldehydephenoxy)butane and various diamines

Six new macrocyclic complexes were synthesized by the template effect from reaction of 1,4-bis(2-carboxyaldehydephenoxy)butane, Ni(NO₃)₂ · 6H₂O or Co(NO₃)₂ · 6H₂O and various diamines. The metal-to-ligand ratios of Ni(II) or Co(II) metal complexes were found to be 1 : 1. Coordination of the Schiff base to Ni(II) and Co(II) through the two nitrogen and two oxygen atom (ONNO) are expected to reduce the electron density in the azomethine link and hydroxyl group. The Ni(II) and Co(II) complexes are proposed to be tetrahedral and are 1 : 2 electrolytes as shown by their molar conductivities (Λ_M) in DMF (dimethyl formamide) at 10^?3 M. The structures are proposed from elemental analysis, FT-IR, UV-VIS, magnetic susceptibility measurements, molar conductivity measurements, and mass spectra.     

Synthesis and properties of poly(ether imide)s derived from 2,6-bis(3,4-dicarboxyphenoxy)naphthalene dianhydride and aromatic diamines

A new naphthalene unit-containing bis(ether anhydride), 2,6-bis(3,4-dicarboxyphenoxy)naphthalene dianhydride, was synthesized in three steps starting from the nucleophilic nitrodisplacement reaction of 2,6-dihydroxynaphthalene and 4-nitrophthalonitrile in N,N-dimethylformamide (DMF) solution in the presence of potassium carbonate, followed by alkaline hydrolysis of the intermediate bis(ether dinitrile) and subsequent dehydration of the resulting bis(ether diacid). High-molar-mass aromatic poly(ether imide)s were prepared using a conventional two-step polymerization process from the bis(ether anhydride) and various aromatic diamines. The intermediate poly(ether amic acid)s had inherent viscosities of 0.65–2.03 dL/g. The films of poly(ether imide)s derived from two rigid diamines, i.e. p-phenylenediamine and benzidine, crystallized during the thermal imidization process. The other poly(ether imide)s belonged to amorphous materials and could be fabricated into transparent, flexible, and tough films. These aromatic poly(ether imide) films had yield strengths of 104–131 MPa, tensile strengths of 102–153 MPa, elongation to break of 8–87%, and initial moduli of 1.6–3.2 GPa. The glass transition temperatures (T_g's) of poly(ether imide)s were recorded in the range of 220–277°C depending on the nature of the diamine moiety. All polymers were stable up to 500°C, with 10% weight loss being recorded above 550°C in both air and nitrogen atmospheres. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1657–1665, 1998     

Synthesis and properties of poly(ether imide)s derived from 2,7-bis(3,4-dicarboxyphenoxy)naphthalene dianhydride and various aromatic diamines

A naphthalene unit-containing bis(ether anhydride), 2,7-bis(3,4-dicarboxyphenoxy)naphthalene dianhydride, was prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 2,7-dihydroxynaphthalene and 4-nitrophthalonitrile in N,N-dimethylformamide (DMF) solution in the presence of potassium carbonate followed by alkaline hydrolysis of the intermediate bis(ether dinitrile) and subsequent dehydration of the resulting bis(ether diacid). High-molar-mass aromatic poly(ether imide)s were synthesized using a conventional two-stage polymerization process from the bis(ether anhydride) and ten aromatic diamines. The intermediate poly(ether amic acid)s had inherent viscosities of 0.95–2.67 dL/g. The films of poly(ether imide)s derived from two rigid diamines, that is, p-phenylenediamine and benzidine, crystallized and embrittled during the thermal imidization process. The other poly(ether imide)s belonged to amorphous materials and could be fabricated into transparent, flexible, and tough films. These poly(ether imide) films had yield strengths of 91–115 MPa, tensile strengths of 89–136 MPa, elongation to break of 11–45%, and initial moduli of 1.7–2.2 GPa. The T_gs of poly(ether imide)s were recorded in the range of 222–256°C depending on the nature of the diamine moiety. All polymers were thermally stable up to 500°C, with 10% weight loss being recorded above 540°C in air and nitrogen atmospheres. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2281–2287, 1997     

Synthesis and spectral studies of macrocyclic Cu(II) complexes by reaction of various diamines,copper(II) perchlorate and 1,4-bis(2-carboxyaldehyde phenoxy)butane

Six macrocyclic complexes, were synthesized by reaction of 1,4-bis(2-carboxyaldehyde phenoxy)butane and various amines and their copper(II) perchlorate complexes were synthesized by template effect reaction of 1,4-bis(2-carboxyaldehyde phenoxy)butane, Cu(ClO₄)₂?·?6H₂O and amines. The metal-to-ligand ratios were found to be 1?:?1. Cu(II) metal complexes are 1?:?2 electrolytes as shown by their molar conductivities (Λ_M) in DMF (dimethyl formamide) at 10^?3?M. The Cu(II) complexes are proposed to be square planar based on elemental analysis, FT–IR, UV–Vis, magnetic susceptibility measurements, molar conductivity measurements, and mass spectra.     

New poly(amide-imide)s syntheses. VIII. Preparation and properties of poly (amide-imide)s derived from 2,3-bis(4-aminophenoxy)naphthalene,trimellitic anhydride,and various aromatic diamines

The new polymer-forming diimide-diacid, 2,3-bis(4-trimellitimidophenoxy) naphthalene (I), was readily obtained by the condensation reaction of 2,3-bis (4-aminophenoxy) naphthalene with trimellitic anhydride. A series of novel aromatic poly (amide-imide)s were prepared by the direct polycondensation of diimide-diacid I with various aromatic diamines using triphenyl phosphite in N-methyl-2-pyrrolidone (NMP)/pyridine solution containing dissolved calcium chloride. The resultant polymers have inherent viscosities in the range of 0.65–1.02 dL/g at 30°C in N, N-dimethylacetamide. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed tensile strength at break up to 86 MPa, elongation to break of 5–9%, and initial moduli up to 2.35 GPa. The wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or p-oxyphenylene group are partially crystalline, and the other polymers are evidenced as amorphous patterns. These polymers show a glass transition in the range of 213–290°C in their differential scanning calorimetry (DSC) traces. The thermal stability of the polymers was evaluated by thermogravimetry analysis, which showed the 10% weight-loss temperatures in the range of 508–565°C in nitrogen and 480–529°C in air atmosphere. © 1994 John Wiley & Sons, Inc.     

New poly(amide-imide)s syntheses. VII. Preparation and properties of poly(amide-imide)s derived from 1,5-bis(4-aminophenoxy) naphthalene,trimellitic anhydride,and various aromatic diamines

New bis(phenoxy)naphthalene-containing poly(amide-imide)s having an inherent viscosity in the range of 0.62–1.09 dL/g were prepared by the direct polycondensation of 1,5-bis(4-trimellitimidophenoxy) naphthalene ( I ) and various aromatic diamines using triphenyl phosphite and pyridine as condensing agents in N-methyl-2-pyrrolidone (NMP) in the presence of calcium chloride. The diimide-diacid (I) was prepared by the condensation of 1,5-bis(4-aminophenoxy) naphthalene and trimellitic anhydride. Most of the polymers were soluble in aprotic solvents such as NMP and N,N-dimethylacetamide (DMAc), and afforded transparent, flexible and tough films upon casting from DMAc solutions. Measurements of wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or oxyphenylene groups were characterized as crystalline polymers. Tensile strength and initial moduli of the polymer films ranged from 61–86 MPa and 1.83–2.21 GPa, respectively. Glass transition temperatures of the polymers were in the range of 231–340°C. The melting points of the crystalline polymers ranged from 375–430°C. The 10% weight loss temperatures were above 512°C in nitrogen and 481°C in air. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of new poly(amide–imide)s from 1,4-bis(4-trimellitimidophenoxy)-2-tert-butylbenzene with various diamines

New poly(amide–imide)s were prepared from a diimide–dicarboxylic acid, 1,4-bis(4-trimellitimidophenoxy)-2-tert-butylbenzene ( BTTB ), with various diamines by the direct polycondensation in N-methyl-2-pyrrolidinone (NMP) using triphenyl phosphite and pyridine as condensing agents. The new diimide–dicarboxylic acid BTTB containing an ether linkage and tert-butyl substituent was synthesized by the condensation reaction of 1,4-bis(4-aminophenoxy)-2-tert-butylbenzene with trimellitic anhydride. All the polymers were obtained in quantitative yields with inherent viscosities of 0.62–1.06 dL g⁻¹. The polymers were amorphous, and most of them were readily soluble in aprotic polar solvents such as NMP, N,N-dimethylacetamide (DMAc), and N,N-dimethylformamide (DMF), as well as in less polar solvents such as dimethyl sulfoxide (DMSO), m-cresol, pyridine, and γ-butyrolactone, and also even in tetrahydrofuran. The glass transition temperatures of the polymers were determined by DSC method, and they were in the range of 238–279°C. These polymers were stable up to 408–449°C in air and 451–483°C in nitrogen and lose 10% weight in the range of 479–525°C in air and 480–528°C in nitrogen atmosphere. The polymer films had a tensile strength range of 71–115 MPa, an elongation at break range of 4–14%, and a tensile modulus range of 2.3–3.1 GPa. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2301–2307, 1998     

New light‐colored poly(ether imide)s based on 2,5‐di‐tert‐butylhydroquinone bis(ether anhydride) and aromatic diamines

A series of poly(ether imide)s (PEIs), III _a–k , with light color and good physical properties were prepared from 1,4‐bis(3,4‐dicarboxypheoxy)‐2,5‐di‐tert‐butylbenzene dianhydride ( I ) with various aromatic diamines ( II _a–k ) via a conventional two‐stage procedure that included a ring‐opening polyaddition to yield poly(amic acid)s (PAA), followed by thermal imidization to the PEI. The intermediate PAA had inherent viscosities in the range of 1.00–1.53 dL g^?1. Most of the PEIs showed excellent solubility in chlorinated solvents such as dichloromethane, chloroform, and m‐cresol, but did not easily dissolve in dimethyl sulfoxide and amide‐type polar solvents. The III series had tensile strengths of 96–116 MPa, an elongation at break of 7–8%, and initial moduli of 2.0–2.5 GPa. The glass‐transition temperatures (T_g) and softening temperatures (T_s's) of the III series were recorded between 232 and 285 °C and 216–279 °C, respectively. The decomposition temperatures for 10% weight loss all occurred above 511 °C in nitrogen and 487 °C in air. The III series showed low dielectric constants (2.71–3.54 at 1 MHz), low moisture absorption (0.18–0.66 wt %), and was light‐colored with a cutoff wavelength below 380 nm and a low yellow index (b^*) values of 7.3–14.8. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1270–1284, 2005