Crystallization and melting behavior of liquid crystalline copolyesters based on poly(ethylene terephthalate)

A series of copolyesters were prepared by the incorporation of p‐hydroxybenzoic acid (HBA), hydroquinone (HQ), and terephthalic acid (TA) into poly(ethylene terephthalate) (PET). On the basis of viscosity measurements, high molar mass copolyesters were obtained in the syntheses, and ¹H‐NMR analyses indicated the total insertion of comonomers. They exhibit nematic phase above melting temperature, as observed by polarized light microscope (PLM). Their crystallization and melting behaviors were also studied by differential scanning calorimetry (DSC) and wide angle X‐ray diffraction (WAXD). It was found that these copolyesters are more crystalline than copolyesters prepared from PET and HBA. Introduction of HQ/TA disrupts longer rigid‐rod sequences formed by HBA, and thus enhances molecular motion and increases crystallization rate and crystallinity. Isothermal crystallization at solid phase polymerization conditions (up to 24 h at 200°C) resulted in increased copolymer randomness (by NMR) and higher melting point, the latter attributed to structural annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 369–377, 1999     

New insight into melting and crystallization behavior in semicrystalline poly(ethylene terephthalate)

After isothermal crystallization, poly(ethylene terephthalate) (PET) showed double endothermic behavior in the differential scanning calorimetry (DSC) heating scan. During the heating scans of semicrystalline PET, a metastable melt which comes from melting thinner lamellar crystal populations formed between the low and the upper endothermic temperatures. The metastable melt can recrystallize immediately just above the low melting temperature and form thicker lamellae than the original ones. The thickness and perfection depends on the crystallization time and crystallization temperature. The crystallization kinetics of this metastable melt can be determined by means of DSC. The kinetics analysis showed that the isothermal crystallization of the metastable PET melt proceeds with an Avrami exponent of n = 1.0 ∼ 1.2, probably reflecting one‐dimensional or irregular line growth of the crystal occurring between the existing main lamellae with heterogeneous nucleation. This is in agreement with the hypothesis that the melting peaks are associated with two distinct crystal populations with different thicknesses. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 53–60, 2000     

Synthesis and characterization of poly(ethylene glycol) methyl ether endcapped poly(ethylene terephthalate)

Linear and branched poly(ethylene terephthalate) (PET) copolymers with polyethylene glycol) (PEG) methyl ether (700 or 2000 g/mol) end groups were synthesized using conventional melt polymerization. DSC analysis demonstrated that low levels of PEG end groups accelerated PET crystallization. The incorporated PEG end groups also decreased the crystallization temperature of PET dramatically, and copolymers with a high content of PEG (>17.6 wt%) were able to crystallize at room temperature. Rheological analysis demonstrated that the presence of PEG end groups effectively decreased the melt viscosities and facilitated melt processing. XPS and ATR-FTIR revealed that the PEG end groups tended to aggregate on the surface, and the surface of compression molded films containing 34.0 wt% PEG were PEG rich (85 wt% PEG). PEG end-capped PET (34.0 wt% PEG) and PET films were immersed into a fibrinogen solution (0.7 mg/mL BSA) for 72 h to investigate the propensity for protein adhesion. XPS demonstrated that the concentration of nitrogen (1.05%) on the surface of PEG endcapped PET film was statistically lower than PET (7.67%). SEM analysis was consistent with XPS results, and revealed the presence of adsorbed protein on the surface of PET films.     

Study of the Crystallization Kinetics. Poly(ethylene oxide) and a blend of poly(ethylene oxide) and poly(bisphenol A-co-epichlorohydrin)

A kinetic study of the crystallization of poly(ethylene oxide) (PEO) and of a blend of PEO+poly(bisphenol A-co-epichlorohydrin) (PBE) was performed by using DSC in a non-isothermal program at constant cooling rates. The curves obtained were analyzed by the Kissinger, Ozawa and Friedman methods, with determination of the kinetic parameters in each case. As a consequence of the presence of PBE, the kinetic parameters were altered, leading to the conclusion that PBE has some influence on the crystallization of PEO, modifying its mechanism. This revised version was published online in July 2006 with corrections to the Cover Date.     

聚丙烯/聚对苯二甲酸乙二酯共混自增强材料的研究(Ⅰ)

本文根据聚丙烯（ＰＰ）与聚对苯二甲酸乙二醇酯（ＰＥＴ）共混对在熔 融状态下．流动粘度差阳溶度参数差大的特点，用挤出造粒的方法制得 共熔成纤目增强材料。通过扫描电镜观察．证实ＰＰ／ＰＥＴ比从９５／５到 ８０／２０时。ＰＥＴ均以纤维状结构分布在ＰＰ基质中。该共熔成纤体具有 良好的机械性能。在未加偶联剂时，拉伸强度虽略比纯ＰＰ低．但抗冲击 强度与纯ＰＰ相当。该结果可用于指导ＰＰ的改性和ＰＥＴ废料再生利用 工作。     

Crystallization kinetics of poly(trimethylene terephthalate)

The isothermal crystallization kinetics of poly(trimethylene terephthalate) (PTT) have been investigated using differential scanning calorimetry (DSC) and polarized light microscopy (PLM). Enthalpy data of exotherm from isothermal crystallization were analyzed using the Avrami theory. The average value of the Avrami exponent, n, is about 2.8. From the melt, PTT crystallizes according to a spherulite morphology. The spherulite growth rate and the overall crystallization rate depend on crystallization temperature. The increase in the spherulitic radius was examined by polarized light microscopy. Using values of transport parameters common to many polymers (U* = 1500 cal/mol, T_∞= T_g − 30 °C) together with experimentally determined values of T (248 °C) and T_g (44 °C), the nucleation parameter, k_g, for PTT was determined. On the basis of secondary nucleation analyses, a transition between regimes III and II was found in the vicinity of 194 °C (ΔT ≅ 54 K). The ratio of k_g of these two regimes is 2.1, which is very close to 2.0 as predicted by the Lauritzen–Hoffman theory. The lateral surface‐free energy, σ = 10.89 erg/cm² and the fold surface‐free energy, σ_e = 56.64 erg/cm² were determined. The latter leads to a work of chain‐folding, q = 4.80 kcal/mol folds, which is comparable to PET and PBT previously reported. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 934–941, 2000     

Fast crystallization of poly(ethylene terephthalate)

The crystallization of poly(ethylene terephthalate) (PET) was studied in the presence of nucleating agents and promoters. The effect of both by themselves and in concert was investigated using differential scanning calorimetry. The aim of this work is to find conditions of fast crystallization of PET. Sodium benzoate(SB) and Surlyn® (S) substantially increase the crystallization rate of PET at higher temperature owing to a reduction in the energy barrier towards primary nucleation, but they accelerate crystallization even more at lower temperature with an additional improvement of the molecular mobility of PET chains. Chain scission of PET caused by the reaction with the nucleating agents was proven by determination of molecular weight. The addition of S alone led to a lower reduction in molecular weight. A series of N-alkyl-p-toluenesulfonamides (ATSAs) were shown to effectively promote molecular motion of the PET chains, leading to an increase in crsytallization rate at lower temperature. A remarkable acceleration of crystallization of PET was attained at lower temperature when S and ATSA were added together. When the content of ATSA is low, S has the dominant influence due to its dual effect of decreasing energy barrier towards nucleation and promoting molecular motion of PET chains. A further increase of crystallization rate of PET was found only after an addition of ATSA of above 5 wt.%.Dedicated to Professor Bernhard Wunderlich on the occasion of his 65th birthdayThis work was supported by State Science and Technology Commission, and partially by National Science Foundation.     

High‐pressure DTA of poly(butylene terephthalate), poly(hexamethylene terephthalate), and poly(ethylene terephthalate)

Pressure effect on the melting behavior of poly(butylene terephthalate) (PBT) and poly(hexamethylene terephthalate) (PHT) was studied by high‐pressure DTA (HP‐DTA) up to 320 and 530 MPa, respectively. Cooling rate dependence on the DSC melting curves of the samples cooled from the melt was shown at atmospheric pressure. Stable and metastable samples were prepared by cooling from the melt at low and normal cooling rates, respectively. DTA melting curves for the stable samples showed a single peak, and the peak profile did not change up to high pressure. Phase diagrams for PBT and PHT were newly determined. Fitting curves of melting temperature (T_m) versus pressure expressed by quadratic equation were obtained. Pressure coefficients of T_m at atmospheric pressure, dT_m/dp, of PBT and PHT were 37 and 33 K/100 MPa, respectively. HP‐DTA curves of the metastable PBT showed double melting peaks up to about 70 MPa. In contrast, PHT showed them over the whole pressure region. HP‐DTA of stable poly(ethylene terephthalate) (PET) was also carried out up to 200 MPa, and the phase diagram for PET was determined. dT_m/dp for PET was 49 K/100 MPa. dT_m/dp increased linearly with reciprocal number of ethylene unit. The decrease of dT_m/dp for poly(alkylene terephthalate) with increasing a segmental fraction of an alkyl group in a whole molecule is explained by the increase of entropy of fusion. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 262–272, 2000     

The effect of annealing on the crystallization of poly(ethylene terephthalate)/polycarbonate blends

The effect of annealing on the morphology and subsequent crystallization kinetics of poly (ethylene terephthalate)/polycarbonate blends have been investigated using differential scanning calorimetry (DSC), polarized light microscopy, and scanning electron microscopy (SEM). During annealing transesterification and phase coarsening occurred, and the final properties were compromizes between these two competing effects. Initially, the effect of phase separation dominated and the rate of cold crystallization of PET increased. Transesterification, however, became increasingly important and the rate of crystallization decreased progressively until finally the blend completely lost the ability to crystallize. At this stage in the reaction a single glass transition was observed and uniform glassy material observed in the SEM. The maximum crystallinity of the blend achieved on heating showed the same trend in first increasing and then decreasing with annealing time. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2129–2136, 2004     

Heterogeneous nucleation on the crystallization poly(ethylene terephthalate)

The crystallization behavior of poly(ethylene terephthalate) (PET) with disodium terephthalate (DST) as nucleating agent was investigated. A detailed analysis of the crystallization course from the melt was made with the Avrami expression. The results demonstrated that DST additive can promote the PET crystallization rate in its entire crystallizable temperature range, and the acceleration degree of DST decreases with increasing temperature after a temperature higher than 180 °C. The values of the Avrami exponent indicated that the crystallization mode in Avrami theory is not suitable for the crystallization of these polymers, and the mechanism of the heterogeneous nucleation on PET crystallization is discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2135–2144, 2003     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

New insight into the crystallization behavior of poly(ethylene terephthalate)/clay nanocomposites

Crystallization behavior of poly(ethylene terephthalate) (PET)/clay nanocomposites has been investigated in terms of differential scanning calorimeter (DSC) analysis, polarizing optical microscopy (POM), and scanning electron microscopy (SEM) observation. The nanocomposites for investigation were prepared via in situ polycondensation. Crystalline morphologies were observed through POM and SEM. The nonisothermal and isothermal crystallization rates of different samples were determined for comparison based on DSC data. Secondary nucleation analysis was also performed based on bulk crystallization data derived from DSC analysis. The results revealed that nucleating abilities of montmorillonites (MMT) depended on the dispersion state of clay in matrix, the surface modification status, and the metallic derivatives released from MMT during in situ synthesis. The quantities of metallic elements released were measured by inductively coupled plasma (ICP) analysis. The results showed that the release of these metallic derivatives was also affected by surfactant molecules anchored on the surface of MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2380–2394, 2008     

Isothermal crystallization kinetics and melting behavior of poly(ethylene terephthalate)/barite nanocomposites

Poly(ethylene terephthalate) (PET)/Barite nanocomposites were prepared by direct melt compounding. The effects of PET‐Barite interfacial interaction on the dynamic mechanical properties and crystallization were investigated by DMA and DSC. The results showed that Barite can act as a nucleating agent and the nucleation activity can be increased when the Barite was surface‐modified (SABarite). SABarite nanoparticles induced preferential lamellae orientation because of the strong interfacial interaction between PET chains and SABarite nanoparticles, which was not the case in Barite filled PET as determined by WAXD. For PET/Barite nanocomposites, the Avrami exponent n increased with increasing crystallization temperature. Although at the same crystallization temperature, the n value will decrease with increasing SABarite content, indicating of the enhancement of the nucleation activity. Avrami analyses suggest that the nucleation mechanism is different. The activation energy determined from Arrhenius equation reduced dramatically for PET/SABarite nanocomposite, confirming the strong interfacial interaction between PET chains and SABarite nanoparticles can reduce the crystallization free energy barrier for nucleus formation. In the DSC scan after isothermal crystallization process, double melting behavior was found. And the double endotherms could be attributed to the melting of recrystallized less perfect crystallites or the secondary lamellae produced during different crystallization processes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 655–668, 2009     

Random copolymers of poly(butylene terephthalate): Effect of thiodiethylene terephthalate units on melting behaviour and crystallization kinetics

The melting behavior and the crystallization kinetics of poly(butylene terephthalate/thiodiethylene terephthalate) copolymers were investigated by DSC technique. The multiple endotherms were influenced both by T _c and composition. By applying the Hoffman—Weeks' method, T _m ⁰ the of the copolymers was derived. The isothermal crystallization kinetics was analyzed according to the Avrami's treatment. Values of the exponent n close to 3 were obtained, independently of T _c and composition. The introduction of thiodiethylene terephthalate units decreased the PBT crystallization rate. H _m was correlated to c _p for samples with different degree of crystallinity and the results were interpreted on the basis of the existence of an interphase.This revised version was published online in November 2005 with corrections to the Cover Date.     

Conformation of the ground-state dimer in poly(ethylene terephthalate)

Absorbance, excitation, and emission measurements have been performed with methyl benzoate and five model compounds, C₆H₅COO (CH₂)_xOOCC₆H₅, x = 2–6. Under appropriate conditions, three of the model compounds (those with x = 3, 4, 5) show evidence for the formation of intramolecular ground-state dimers. The model compound with x = 5 can form two types of dimers which emit with different energies. The model compound with x = 3 forms one of these dimers, and the model compound with x = 4 prefers the other ground-state dimer. Molecular modeling of the dimers suggests that the two conformations of the ground-state dimers differ in the orientation of the two C?O bonds. In the one dimer these two bonds are nearly parallel, but in the other they make an angle of about 120°. © 1993 John Wiley & Sons, Inc.     

Structural features of crystallized poly(ethylene terephthalate) polymers

Polyethylene terephthalate (PET) is a widely used polymeric material. In this work, the microstructural features before and after the solid‐state polymerization (SSP) of several DuPont PET products were investigated by low‐voltage scanning electron microscopy (LV‐SEM) and atomic force microscopy (AFM). The microstructural features on the cross section of various PET samples included crystallites, voids, boundaries, defects, and amorphous phases. The SEM images revealed layered and stepped structural features at the micron and 10‐micron scales that are highly crystallized at the near‐edge region of the cross section for both linear and branched PET samples after the SSP process. The AFM images demonstrate that the degree of crystallization for the linear and branched PET samples increases gradually from the central area to the edge on the cross section. The linear crystallized PET has a higher degree of orientation than the branched crystallized PET in the 10‐micron to micron scales, but their crystalline structures have no significant differences in the submicron to nanometer scales. The PET crystallization process occurs when the molecular chains in the amorphous phase are aligned and folded to form straight molecular chains at the nanometer scale, and small crystallites are formed. The crystallites aggregate and align together into a polygon rod‐like‐shaped crystallites at the submicron scale. Finally, large crystallites at the micron size are formed that appear on the edge area of the cross section. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 245–254, 2002     

Miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) blends by transesterification

The effects of transesterification on the miscibility of poly(ethylene terephthalate)/poly(ethylene 2,6-naphthalate) were studied. Blends were obtained by solution precipitation at room temperature to avoid transesterification during blend preparation. The physical blends and transesterified products were analyzed by wide-angle x-ray scattering, differential scanning calorimetry, and nuclear magnetic resonance spectroscopy. It was found that the physical blends are immiscible and when the extent of transesterification reaches 50% of the completely randomized state, independent of blend composition, the blends are not crystallizable and show a single glass transition temperature between those of starting polymers. The interchange reactions were significantly influenced by annealing temperature and time but negligibly by blend composition. © 1996 John Wiley & Sons, Inc.     

Crystallization behavior and morphology of poly(propylene terephthalate) copolymers containing neopenthyl glycol moieties

The melting behavior and the crystallization kinetics of random poly(propylene/neopenthyl terephthalate) copolymers (PPT‐PNT) were investigated by means of differential scanning calorimetry and hot‐stage optical microscopy. Multiple endotherms were evidenced in the PPT‐PNT samples, due to melting and recrystallization processes, similarly to PPT. By applying the Hoffman‐Weeks' method, the T_m° of the copolymers was derived. Baur's equation described well the T_m‐composition data. The isothermal crystallization kinetics was analyzed according to the Avrami's treatment. The introduction of NT units decreased the crystallization rate in comparison to pure PPT. Values of the Avrami's exponent close to three were obtained in all cases, regardless of T_c, in agreement with a crystallization process originating from predeterminated nuclei and characterized by three dimensional spherulitic growth. As a matter of fact, space‐filling spherulites were observed by optical microscopy at all T_cs. Banded spherulites were found for PPT‐PNT5 and PPT‐PNT10, the band spacing being affected by both T_c and composition. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 818–830, 2008     

A differential scanning calorimetry study on poly(ethylene terephthalate) isothermally crystallized at stepwise temperatures: multiple melting behavior re-investigated

The multiple melting behavior of poly(ethylene terephthalate) (PET) was investigated with differential scanning calorimetry (DSC) by examining PET samples having been subjected to special schemes of crystallization and annealing treatment at multiple descending temperatures. Upon such step-wise annealing in decreasing temperatures, the existence of doublet melting peaks in addition to a series of multiple minor peaks in the PET has been demonstrated using carefully designed thermal schemes. Using the Hoffman theory, multiple lamellae populations, might be suggested to be simultaneously present in the PET subjected to such thermal treatments. However, direct experimental evidence has yet to be provided. The low-temperature minor crystals simply melt during normal scanning without having time enough to reorganize into higher-melt crystals. Nevertheless, the effect of scanning on non-isothermal crystallization does exist but is primarily confined to the temperature range much below the main melting region where the crystallization of polymer chains can progress at a reasonable rate. At higher temperatures near the main melting region, annealing for extended times is required in order to result in relative changes of the melting endotherms of the upper and lower peaks in the main melting doublet. In all we have shown that interpretations of the multiple melting phenomenon in semicrystalline polymers can be better refined.     

Poly(ethylene terephthalate) copolymers containing nitroterephthalic units. I. Synthesis and characterization

The synthesis, microstructure, and thermal behavior of a series of poly(ethylene terephthalate) (PET) copolymers containing nitroterephthalic units are described. These novel copolyesters were synthesized by transesterification followed by melt copolycondensation of dimethyl terephthalate and dimethyl nitroterephthalate mixtures with ethylene glycol. The molar ratio of the two comonomers in the feed varied from 95/5 to 25/75. Furthermore, PET and poly(ethylene nitroterephthalate) homopolymers were synthesized with the same method and comparatively studied. Copolyester compositions were practically the same as in the feed, and weight‐average molecular weights ranged from 10,000 to 60,000. The two monomeric units were randomly distributed along the polymer chain, and the experimentally determined average sequence lengths were in accordance with ideal copolycondensation statistics. Melting temperatures and enthalpies of the copolyesters decreased with increasing content in nitroterephthalic units, and they all showed a single glass‐transition temperature superior to that of PET. They appeared to be stable up to 300 °C, and thermal degradation occurred in two well‐differentiated steps. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3761–3770, 2000