Mesomorphic and luminescent properties of side chain nematic liquid-crystalline polymers containing Ir(III)

Iridium-containing liquid-crystalline polymers were obtained by graft copolymerisation using poly(methylhydrogeno)siloxane, 1-methyl-4-(4-(4-vinylcyclohexyl)cyclohexyl)benzene (M₁) and an iridium complexes monomer (Ir-M₂). The series of polymers contained different molecular fractions of Ir-M₂ from 0% to 1.2%. All of these polymers showed mesomorphic behaviours. The introduction of small amount of iridium ions endowed liquid-crystalline polymers with luminescent properties. The chemical structures were characterised by IR and ¹H NMR. The mesomorphic properties and phase behaviour were investigated by differential scanning calorimetry, thermal gravimetric analysis, polarising optical microscopy and X-ray diffraction. With an increase of iridium complexes units in the polymers, the glass transition temperature (T_g) did not change significantly; the isotropic temperature (T_i) decreased. All polymers showed typical nematic marble textures, which was confirmed by X-ray diffraction. The temperatures at which 5% weight loss occurred (T_d) were greater than 300°C for the polymers. The introduction of iridium complexes units did not change the liquid-crystalline state of polymer systems. With Ir³⁺ ion contents ranging between 0.6 and 2.4 mol%, luminescent intensity of polymers gradually increased.     

Synthesis and characterization of mesogen‐jacketed liquid‐crystal polymers based on 2,5‐bis(4′‐alkoxyphenyl)styrene

A series of novel mesogen‐jacketed liquid‐crystal polymers, poly[2,5‐bis(4′‐alkoxyphenyl)‐styrene] (P‐n, n = 1–11), were prepared via free‐radical polymerization of newly synthesized monomers, 2,5‐bis(4′‐alkoxyphenyl)styrene (M‐n, n = 1–11). The influence of the alkoxy tail length on the liquid‐crystalline behaviors of the monomers and the polymers was investigated with differential scanning calorimetry (DSC), thermogravimetry, polarized optical microscopy (POM), and wide‐angle X‐ray diffraction (WAXD). The monomers with n = 1–4, 9, and 11 were monotropic nematic liquid crystals. All other monomers exhibited enantiotropic nematic properties. Their melting points (T_m's) decreased first as n increased to 6, after which T_m increased slightly at longer spacer lengths. The isotropic–nematic transition temperatures decreased regularly with increasing n values in an odd–even way. The glass‐transition temperatures (T_g's) of the polymers first decreased as the tail lengths increased and then leveled off when n ≥ 7. All polymers were thermally stable and entered the mesophase at a temperature above T_g. Upon further heating, no mesophase‐to‐isotropic melt transition was observed before the polymers decomposed. WAXD studies indicated that an irreversible order–order transition for the polymers with short tails (n ≤ 5) and a reversible order–order transition for those with elongated tails (n ≥ 6) occurred at a temperature much higher than T_g. However, such a transition could not be identified by POM and could be detected by DSC only on heating scans for the polymers with long tails (n ≥ 7). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1454–1464, 2003     

Liquid crystal dimers and the twist-bend nematic phase. The preparation and characterisation of the α,ω-bis(4-cyanobiphenyl-4′-yl) alkanedioates

Eleven members of the homologous series of liquid crystal dimers, the α,ω-bis(4-cyanobiphenyl-4′-yl) alkanedioates, have been synthesised and their transitional properties characterised. These dimers consist of two cyanobiphenyl units connected by an alkyl spacer attached via ester linkages. All eleven members exhibit exclusively nematic behaviour. The nematic–isotropic transition temperatures, T_NI, and associated entropy changes, ?S_NI/R, exhibit pronounced alternations as the length and parity of the spacer is varied; this is characteristic behaviour of liquid crystal dimers. The transitional properties of the ester-linked dimers are compared with the corresponding materials having either ether, methylene or carbonate linkages between the spacer and mesogenic units. For short spacer lengths and both odd- and even-membered dimers, the ester-linked materials show the highest values of T_NI and the methylene-linked the lowest. For longer spacer lengths, T_NI of the carbonate-linked dimers fall between those of the corresponding ester- and ether-linked dimers. The ether-linked materials show the largest alternation in ?S_NI/R on varying spacer length and the carbonate-linked dimers the lowest. This behaviour is interpreted in terms of the molecular geometry and it is suggested that the ether- and ester-linked odd-membered dimers have rather similar shapes. A phase diagram constructed using binary mixtures of the pentyl member of this ester-linked series and the known twist-bend nematogen, 1,7-bis(4-cyanobiphenyl-4′-yl)heptane (CB7CB), is presented. The twist-bend nematic–nematic transition temperature of the mixtures shows a striking convex curvature as the concentration of CB7CB is decreased, and so it is not possible to estimate a virtual twist-bend nematic–nematic transition temperature for the ester-linked material.     

The kerr effect in the vicinity of the transition from the isotropic to smectic a phase

The equilibrium electrooptical effect in the isotropic phase of seven liquid crystalline substances (4-n-decyloxy-4′-cyanobiphenyl, carbosilane dendrimer of the fourth generation with cyanobiphenyl terminal fragments, and the fourth, fifth, sixth, seventh, and tenth members of the homologous series of 4-n-acylphenylene 4′-n-alkoxybenzoates) was studied. The smectic A phases were found to exhibit weaker divergence of the Kerr constant in the vicinity of the T _c isotropic melt-liquid crystal phase transition temperature compared with the nematic phases. The difference between T _c and the temperature T* of the virtual second-order phase transition varied from 3.2 to 19.0 K for the smectic A phases, which substantially exceeded the value (T _c-T*) ≤ 1 K for the nematic phases. A theory of the electrooptical properties of isotropic melts in the vicinity of the T _c temperature of the phase transition from the isotropic to smectic A phase is developed. An equation relating the T _c-T* difference to the phenomenological coefficients of the expansion of the Helmholtz energy of an isotropic melt into a series in powers of the coordination and orientational order parameters is obtained.     

A study of enthalpic relaxation of a liquid crystal

A liquid crystal, BL038, which was observed not to crystallize, has a glass transition at 215 K and a nematic to isotropic transition at 380 K. Samples aged below the glass transition at various temperatures T _a, exhibited an endotherm at the transition which developed with extent of ageing time, t _a. We attribute this endotherm to the relaxation of the glass towards the equilibrium liquid. The progress of the relaxation process was measured using differential scanning calorimetry. On subsequent reheating, the aged glass showed an apparent shift in the glass transition to higher temperatures. The endotherm was used to define the extent of enthalpic relaxation and the maximum value observed was found to increase initially then decrease, with the extent of undercooling from the glass transition temperature, Δ T, passing through a maximum for a Δ T = 15 K. From the temperature dependence of the relaxation times, an apparent activation enthalpy for the relaxation process of 85 ± 10 kJ mol^-1 was determined. The small value of the activation enthalpy compared with that found in the ageing of polymers reflects differences in the molecular species involved in relaxation processes.     

Equilibrium phase diagram of polystyrene and 8CB

The experimental equilibrium phase diagram of a mixture of linear polystyrene of molecular weight M_w = 44,000 g/mol and 4‐cyano‐4′‐n‐octyl‐biphenyl (8CB) is established. The three transitions smectic A‐nematic, nematic‐isotropic, and isotropic‐isotropic are observed. The first two are observed both by optical microscopy and differential scanning calorimetry (DSC) while the isotropic‐isotropic transition could be seen only via optical microscopy. Two series of samples with the same compositions were independently prepared and yielded consistent results both by microscopy and DSC. Measurements of sample compositions with less than 50 weight % of 8CB were influenced by the vicinity of the glass transition temperature (T_g) of the polymer in the mixture. This quantity is also determined by DSC as a function of composition. A single T_g is observed, which decreases with composition of the LC. Other thermodynamic quantities such as the enthalpy variations of LC in the nematic‐isotropic transition and the fraction of LC contained in the droplets are also considered. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1841–1848, 1999     

Pressure and volume dependence of thermal conductivity and isothermal bulk modulus up to 1 GPa for poly(isobutylene)

The thermal conductivity λ and heat capacity per unit volume ρc_p of poly(isobutylene)s, one 2.8 in weight average molecular weight and one 85 kg mol⁻¹ in viscosity average molecular weight (PIB-2800 and PIB-85000), have been measured in the temperature range 170–450 K at pressures up to 2 GPa using the transient hot-wire method. At 297 K and atmospheric pressure, λ = 0.115 W m⁻¹ K⁻¹ for PIB-2800 and λ = 0.120 W m⁻¹ K⁻¹ for PIB-85000. The bulk modulus B_T has been measured in the temperature range 170–297 K up to 1 GPa. At atmospheric pressure, the room temperature bulk moduli B_T are 2.0 GPa for PIB-2800 and 2.5 GPa for PIB-85000 with dB_T/dp = 10 for both. These data were used to calculate the volume dependence of λ, At room temperature and atmospheric pressure (liquid phase) we find g = 3.4 for PIB-2800 and g = 3.9 for PIB-85000, but g depends strongly on temperature for both molecular weights. The difference in g between the glassy state and liquid phase is small and just outside the inaccuracy of g of about 8%. The best predictions for g are given by the theoretical model of Horrocks and McLaughlin. We have found that PIB exhibits two relaxations, where one is associated with the glass transition. The value for dT_g/dp at atmospheric pressure (for the main glass transition) is about 0.21 K MPa⁻¹ for both molecular weights. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1781–1792, 1998     

Cyanobiphenyl-based liquid crystal dimers and the twist-bend nematic phase

ABSTRACT

The synthesis and characterisation of several members of the 1,ω-bis(4-cyanobiphenyl-4′-yl) alkane (CBnCB) and the 1-(4-cyanobiphenyl-4′-yloxy)-ω-(4-cyanobiphenyl-4′-yl) alkane (CBnOCB) homologous series are reported. The new odd members described CB5CB, CB13CB, CB4OCB, CB8OCB and CB10OCB all exhibit twist-bend nematic and nematic phases. The members of these series already reported in literature, CB7CB, CB9CB, CB11CB and CB6OCB, were also prepared in order to allow for a direct comparison of their transitional properties. The properties of these dimers are also compared to those of the corresponding members of the 1,ω-bis(4-cyanobiphenyl-4,-yloxy) alkanes (CBOnOCB). For any given total spacer length, for odd members of these series, the nematic–isotropic transition temperatures and associated entropy changes are greatest for the CBOnOCB dimer and lowest for the CBnCB dimer. These trends are understood in terms of molecular shape. For short spacer lengths, the twist-bend nematic–nematic transition temperature (T_NTBN) is higher for the CBnOCB series than for the CBnCB series but this is reversed as the spacer length increases. Of the CBOnOCB dimers, a virtual value of T_NTBN was estimated for CBO3OCB and T_NTBN was measured for CBO5OCB. These values are considerably lower than those observed for the corresponding members of the CBnCB or CBnOCB series. The dependence of T_NTBN on molecular structure is discussed not only in terms of the molecular curvature but also in the ability of the molecules to pack efficiently. As the temperature range of the preceding nematic phase increases, so the twist-bend nematic–nematic transition entropy change decreases and the transition approaches second order for the longer spacers. For comparative purposes, the transitional behaviour of the even-membered dimers CB6CB, CB5OCB and CBO4OCB is reported and differences accounted for in terms of molecular shape.     

Dielectric studies of liquid crystals under high pressure II. Low frequency relaxation process in 4-n-pentyl-4′-cyanobiphenyl in relation to theories of the nematic state

Abstract

The results of high pressure dielectric studies of 4-n-pentyl-4′-cyanobiphenyl (5CB) are analysed in terms of theories of the nematic state. The retardation factor g∥ = τ∥/τ₀ and the effective, single-particle potential of mean torque were calculated at the nematic–isotropic transition temperature T _NI and along the isothermal, isobaric and isochoric paths within the nematic phase of 5CB. The potential of mean torque is compared with the order parameter known for the same conditions. The values of parameter γ relating the potential to the volume is discussed.     

High-pressure studies on the coacervation of copoly(<Emphasis Type="Italic">N</Emphasis>-vinylformamide–vinylacetate) and copoly(<Emphasis Type="Italic">N</Emphasis>-vinylacetylamide–vinylacetate)

The effects of pressure on the temperature-induced coacervation of copoly( N-vinylformamide–vinylacetate) and copoly( N-vinylacetylamide–vinylacetate) in aqueous solution were investigated by measuring the apparent light scattering, and the effects of the concentrations of polymer and inert salt were also studied. At lower pressures, the apparent temperature of transition, T _c, increased with an increase in the pressure, but further increases in pressure decreased T _c. In contrast, the apparent pressure of transition, P _c, monotonously increased with decreasing fixed temperature. The T– P diagram was elliptical, but the curvature was not large and extrema were not observed in the low-temperature and high-pressure range. Anions with low lyotropic numbers induced an almost linear decrease in the T _c and P _c, whereas anions with a high number increased the T _c and P _c. In both polymers, the T _c and P _c depended on the concentrations of the polymers, reflecting the association/aggregation mechanism of coacervation. This is in contrast to typical thermoresponsive polymers such as poly( N-isopropylacrylamide) and poly( N-vinylisobutyramide), which show the coil-collapse transition as a single molecular event.     

Effects of acrylic acid incorporation on the pressure–temperature behavior and the calorimetric properties of poly(N-isopropylacrylamide) in aqueous solutions

 We studied the effects of pH on the pressure–temperature dependence of coil–collapse transition for aqueous solutions of copolymers of N-isopropylacrylamide and acrylic acid (Ac). At low pressures, the transition temperature (T _tr) increased with pressure, but T _tr decrease with increasing pressure at pressures higher than 50–100 MPa. By increasing the pH, the transition contour shifted to a higher temperature. When the Ac content was increased, the effects of pH became more evident. From a calorimetric study at atmospheric pressure, ΔH _tr was found to become smaller by increasing the portion of the ionized residues in the copolymer. The ratio to the van't Hoff enthalpy changes became larger with an increase in pH, which indicated that the production of charge decreased the cooperative domain size. Received: 19 July 1999 /Accepted in revised form: 7 September 1999     

Transitions and morphology of a thermotropic liquid-crystalline polyester with a flexible spacer

The mesomorphic transitions, crystallization from the mesophase, and the influence of the specimen preparation method on the solid-state structure of an aromatic polyester containing a triad aromatic ester mesogenic group and a decamethylene flexible spacer in the main chain were studied by DSC, SALS, WAXS, polarizing microscopy, torsional braid analysis, and depolarizing transmittance techniques. The specimens obtained from solution were semicrystalline and exhibited nematic mesophase formation above the melting point T_m, whereas the melt-cast specimens were mesomorphic as cast. A transition from the nematic phase to another mesophase, designated M_x, is proposed to occur below T_m, so this transition is monotropic. It appears that the transition to the M_x mesophase occurs before, and may even be a prerequisite for, crystallization of the melt-cast specimens. The thermal expansion coefficient of the anisotropic melt is close to that of the isotropic melt, and the T_g of the supercooled solid mesophase is close to that of the amorphous phase.     

Dynamic mechanical and thermal behavior of thermotropic polyesters based on 4,4-alkane-1-ω-diylbis(4-hydroxybenzoic acid) and 4,4-(pentane-1,5-diyloxy)dibenzoic acid

Thermotropic polyesters based on 4,4^′-alkane-1-ω-diylbis(4-hydroxybenzoic acid) and 4,4^′-(pentane-1,5-diyloxy)dibenzoic acid were studied by dynamic mechanical spectroscopy, X-ray scattering, differential scanning calorimetry and polarizing microscopy. The effect of structure changes in the mesogenic group as well as in the flexible spacer, in particular the incorporation of Cl atoms into the mesogen, introduction of ether oxygen into spacer and the number of CH₂ groups in spacer was investigated. More complex mechanical and thermal behaviour was found on second heating scan than on first cooling of the isotropic melt; higher values of mechanical functions were observed in the isotropic state than in the nematic state of melts. While an even number of CH₂ groups and the presence of ether oxygen in spacer shifts the transition temperatures to higher values, the incorporation of Cl atoms into the mesogen leads to disappearance of ordered structure and the polymers behave as amorphous materials.     

Aqueous solution behavior of thermosensitive (N-isopropylacrylamide-acrylic acid-ethyl methacrylate) terpolymers

A series of N-isopropylacrylamide (NIPAM)-acrylic acid–ethyl methacrylate terpolymers with varied monomer compositions was prepared by radical polymerization. The solution behavior of these polymers was studied in dilute aqueous solution using spectrophotometry, fluorescence spectroscopy and high-sensitivity differential scanning calorimetry. The results obtained revealed that the lower critical solution temperatures depend strongly on the copolymer composition, solution pH and ionic strength. At a high pH, the ionization of acrylic acid (AA) units leads to an increase in solution cloud points (T_c). Solutions of polymers containing 10% or less of AA display a constant T_c for pH above 5.5, with 15% there is a continuous increase in T_c with pH and, for higher AA contents, no clouding was observed within the studied temperature range. Fluorescence probe studies were conducted by following the I ₁/I ₃ ratio of pyrene vibronic bands and the emission of anilinonaphtalene sulfonic acid, sodium salt (ANS), both approaches revealing the existence of hydrophobic domains for polymers with higher ethyl methacrylate content at temperatures lower than T_c, suggesting some extent of aggregation and/or a coil-to-globule transition. Scanning calorimetry measurements showed an endothermic transition at temperatures agreeing with the previously detected cloud points. Moreover, the transition curves became broader and with a smaller transition enthalpy, as both the AA content and the solution pH were increased. These broader transitions were interpreted to be the result of a wider molecular distribution upon polymer ionization, hence, displaying varied solution properties. The decrease in transition enthalpy was rationalized as a consequence of reminiscent hydration of NIPAM units, even after phase separation, owing to the presence of electric charges along the polymer chain.     

Facile Synthesis of Liquid Crystal Dimers Bridged with a Phosphonic Group

Liquid crystal (LC) dimers with well-defined composition and structure arouse broad attentions for their exhibiting LC properties beyond conventional low molar mass mesogens and serving as fascinating model compounds for LC polymers. Here in this work, a series of LC dimers bridged with a phosphonic group have been synthesized through a facile free radical mediated addition reaction between hypophosphorous acid and vinyl terminated cyanobiphenyl mesogens with variant length alkyl spacers. In addition, two esterified derivatives and a group of mono-addition homologues with a terminal phosphonic acid group have also been prepared for comparison study. All the newly synthesized compounds exhibit monotropic nematic (N) phase with typical schlieren textures except for the LC dimer with the longest eleven-methylene spacer, which surprisingly shows twist-bend nematic (N_TB) phase directly from the isotropic state upon cooling. Moreover, the thermal transition properties such as the nematic-isotropic transition temperatures and associated entropy changes of the series LC dimers display a modest odd-even effect. Furthermore, both the LC dimers and the mono-addition homologues in N phase are quite easy to achieve homeotropic alignment upon annealing thanks to the supramolecular interactions between the introduced phosphonic acid group and the hydroxylated glass surface. This work thus provides a novel synthesis strategy for a class of LC materials bridged with a phosphonic acid group prone to further functionalization, which may serve as promising vertical alignment agents and pave the way for developing a new kind of functionalized LC materials of N_TB phase.     

Thermomechanical trnasitions in polyphosphazenes

Unoriented and oriented samples of two phosphazene homopolymers with chemical structure [NPX₂]_n, where X = CF₃CH₂O and p-CH₃C₆H₄O, and three unfilled and filled alkoxy-type polyphosphazene copolymers, plus one filled aryloxy-type copolymer were examined with a Rheovibron viscoelastometer. Measurements were made from ?120°C to temperatures above the T(1) transition of the respective polymers. The effects of orientation and repeated temperature cycling through the T(1) transition temperatures were studied. The overall physical behavior of these polyphosphazenes was dominated by changes that occurred in the primary softening dispersion and the mesomorphic or T(1) transition region. The enthalpy of the T(1) transition and the T(1) temperature were investigated by differential scanning calorimetry (DSC) as a function of temperature cycling in the T(1) region; for instance, the change in enthalpy in the T(1) region is about an order of magnitude larger than it is at T_m for the unfilled polyphosphazene homopolymers. The T_g's of the polyphosophazenes were also determined. Density measurements were made on oriented and unoriented specimens by the flotation method. Although an increase in density (and crystallinity) was observed when specimens were cycled through the T(1) transition, no significant difference in density was found between oriented and unoriented materials. Some discussion of the molecular origin of the T(1) transition is included.     

Model phase diagrams of binary nematic mixtures. A comparative study between linear and crosslinked polymers

Model calculations of phase diagrams of side chain liquid crystal polymers (SCLCP) and low molecular weight liquid crystals (LMWLC) are presented. The polymer is assumed to have grafted side chain units characterized by a nematic‐isotropic transition temperature T_{NI 2}, and the LMWLC presents also a similar transition at a temperature T_{NI 1} . The model calculations can accommodate for the cases where the latter two temperatures are comparable or widely different. For the sake of illustration, the case T_{NI 1} = 60°C and T_{NI 2} = 80°C is adopted here. The main point of interest here is to perform a comparative study of the equilibrium phase diagrams of SCLCP made either of linear free chains or crosslinked chains forming a single network. To our knowledge this is the first comparative study of the phase behavior of binary nematic mixtures involving linear and crosslinked polymer matrices which permits to clearly identify the effects of crosslinks present in the polymer matrix. The crosslinks attribute elasticity to the polymer constituent which induces important distortions in the phase diagram. To highlight these distortions, examples of hypothetical binary nematic mixtures are chosen involving both linear and crosslinked polymers with side chain mesogen units. The quadrupole interaction parameter between the two nematogens is related to individual parameters via a geometric average ν²₁₂ = κν₁₁ν₂₂ with a coupling parameter κ. Different values of this parameter are considered and the impact of coupling strength on the phase diagram is discussed for crosslinked and linear polymers.     

Effect of pressure on liquid crystal dimers

We report high pressure investigations on a homologous series of liquid crystalline dimeric molecules in which the terminal chain length is kept constant but the length of the methylene spacer connecting the two mesogenic units is varied. We find that unlike the nematic–isotropic transition temperature and associated entropy change, there is no alternation in the slope of the nematic–isotropic phase boundary in the pressure–temperature plane as a function of the length of the spacer group in the molecule. By applying the Clausius–Clapeyron equation we conclude that the volume change at the transition should exhibit a strong odd–even effect. Measurements on the shortest homologue of the series, which is non-mesomorphic, show the expected result that the application of pressure induces mesomorphism in non-mesomorphic compounds.     

LC-polyimides XXXIV. Noncrystalline thermotropic copoly(ester-imide)s based on PET

Four series of copoly(ester-imide)s (co-PEIs) were prepared by transesterification of poly(ethylene terephthalate), PET, with N-(4-carboxyphenyl)trimellitimide and an acetylated diphenol. Methylhydroquinone, tert. butylhydroquinone, phenylhydroquinone, and 2,7-dihydroxynaphthalene were used as diphenols. The chemical structures of these co-PEIs were characterized by chemical analyses, ¹H-, and ¹³C-NMR spectra. A low degree of crystallinity was observed when the PET content was above 85% mol %. Between 60 and 80 mol % PET all co-PEIs are biphasic, whereas below 60 mol % the co-PEIs form a homogeneous nematic melt and below the glass transition temperature (T_g) a nematic glass. The T_gs vary continously with the molar composition but the mechanical properties drop sharply when the nematic phase changes to an isotropic one. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1813–1820, 1998     

新型含氧亚甲基和亚胺桥键的液晶化合物的合成及介晶性

报道一类新的、结构通式为MeO₂CC₆H₄CH₂OC₆H₄CH＝NC₆H₄Y, Y＝OC_nH_2n＋1, Me, Cl, Br, NO₂, H 的棒状液晶化合物的合成. 通过DSC和偏光显微镜对其介晶性研究发现, 除Y＝H外, 这些化合物均具有介晶性. 当Y为非烷氧基时, 呈向列相液晶; 当Y为较短的烷氧基时(n＝1～3), 液晶化合物具有向列相(N); Y为较长烷氧基时(n＝4～16 ), 液晶化合物只有近晶B相(S_B)和近晶A相(S_A); S_A-I相变的熵变随烷氧链原子数而奇-偶变化, 但与N-I相变的“奇-偶效应”相反.