Synthesis and properties of poly(arylene ether phenyl-s-triazine)s

A series of new poly(arylene ether phenyl-s-triazine)s was prepared by the nucleophilic aromatic substitution polymerization of the potassium salt of bisphenols with 2,4-bis (halophenyl)-6-phenyl-s-triazine in N-methyl-2-pyrrolidone at elevated temperature. The polymers with inherent viscosities exceeding 0.5 were obtained after polymerization for 1 h using 2,4-bis(fluorophenyl)-6-phenyl-s-triazine as a monomer. The glass transition temperatures of the resulting polymers ranged from 200 to 260°C depending on the bisphenol used in the polymer synthesis. The poly(arylene ether phenyl-s-triazine)s demonstrated excellent thermal stabilities in excess of 490°C (5% weight loss in air). The isothermal TGA measurements (400°C under air or nitrogen atmosphere) revealed that the 4,4'-biphenol- and hydroquinone-based poly(arylene ether phenyl-s-triazine)s belong to the most superior class of heat resistant polymers, such as polyimide Kapton?. The mechanical properties of these polymers are also described. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(arylene ether)s derived from 4,4′‐bishydroxybiphenyl and 4,4′‐bishydroxyterphenyl

A series of poly(arylene ether)s were successfully prepared by aromatic, nucleophilic substitution reactions with various perfluoroalkyl‐activated bisfluoromonomers with 4,4′‐bishydroxybiphenyl and 4,4′‐bishydroxyterphenyl. 4,4′‐Bishydroxyterphenyl was synthesized through the Grignard coupling reaction of magnesium salt of 4‐bromoanisole with dibromobenzene followed by demethylation with pyridine–hydrochloride. The products obtained by the displacement of fluorine atoms exhibited good inherent viscosity, up to 0.77 dL/g, and number‐average molecular weights up to 69,300. These poly(arylene ether)s showed very good thermal stability, up to 548 °C for 5% weight loss according to thermogravimetric analysis under synthetic air, and high glass‐transition temperatures, up to 259 °C according to differential scanning calorimetry, depending on the exact repeat unit structure. These polymers were soluble in a wide range of organic solvents, such as N‐methylpyrrolidone, dimethylformamide, tetrahydrofuran, toluene, and CHCl₃, and were insoluble in dimethyl sulfoxide and acetone. Thin films of these poly(arylene ether)s showed good transparency and exhibited tensile strengths up to 132 MPa, moduli up to 3.34 GPa, and elongations at break up to 84%, depending on their exact repeating unit structures. These values are comparable to those of high‐performance thermoplastic materials such as poly(ether ether ketone) (PEEK) and Ultem poly(ether imide) (PEI). These poly(arylene ether)s exhibited low dielectric constants. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 55–69, 2002     

Poly(arylene ether)s and poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)- phthalazinone moiety

A series of new high molecular weight poly(arylene ether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have been synthesized. The inherent viscosities of these polymers are in the range of 0.33–0.64 dL/g. They are amorphous and readily soluble in chloroform, DMF, and DMAc. The glass transition temperatures of the polymers range from 241 to 320°C and the 5% weight loss temperatures in nitrogen atmosphere range from 473 to 517°C. The hydroxy group in the monomer 1,2-dihydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one has been selectively transformed into the N,N′-dimethylthiocarbamate group, which was then rearranged to give the S-(N,N′-dimethylcarbamate) group via the Newman–Kwart rearrangement reaction. A series of poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have also been synthesized via two types of reactions, a N C coupling reaction and a one-pot reaction between the S-(N,N′-dimethylcarbamate) and activated dihalo compounds, in diphenyl sulfone in the presence of a cesium carbonate and calcium carbonate mixture. These poly(arylene thioether)s also have high glass transition temperatures (ranging from 217–303°C) and high thermal stabilities. Compared with their poly(ether) analogs, the poly(arylene thioether)s have glass transition temperatures several degrees lower, which is attributed to the more flexible C S C bonds. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36 : 455–460, 1998     

Synthesis and characterization of soluble polyimides derived from 2′,5′‐bis(3,4‐dicarboxyphenoxy)‐p‐terphenyl dianhydride

A novel bis(ether anhydride) monomer, 2′,5′‐bis(3,4‐dicarboxyphenoxy)‐p‐terphenyl dianhydride, was synthesized from the nitro displacement of 4‐nitrophthalonitrile by the phenoxide ion of 2′,5′‐dihydroxy‐p‐terphenyl, followed by alkaline hydrolysis of the intermediate bis(ether dinitrile) and cyclodehydration of the resulting bis(ether diacid). A series of new poly(ether imide)s bearing laterally attached p‐terphenyl groups were prepared from the bis(ether anhydride) with various aromatic diamines via a conventional two‐stage process that included ring‐opening polyaddition to form the poly(amic acid)s followed by thermal or chemical imidization to the poly(ether imide)s. The inherent viscosities of the poly(amic acid) precursors were in the range of 0.62–1.26 dL/g. Most of the poly(ether imide)s obtained from both routes were soluble in polar organic solvents, such as N,N‐dimethylacetamide. All the poly(ether imide)s could afford transparent, flexible, and strong films with high tensile strengths. The glass‐transition temperatures of these poly(ether imide)s were recorded as between 214 and 276 °C by DSC. The softening temperatures of all the poly(ether imide) films stayed in the 207–265 °C range according to thermomechanical analysis. For all the polymers significant decomposition did not occur below 500 °C in nitrogen or air atmosphere. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1008–1017, 2004     

Synthesis and properties of poly(ether imide)s based on a benzonorbornane bis(ether anhydride)

A novel bis(ether anhydride) monomer, 3,6‐bis(3,4‐dicarboxyphenoxy)benzonorbornane dianhydride, was synthesized from the nitro displacement of 4‐nitrophthalonitrile with 3,6‐dihydroxybenzonorbornane in the presence of potassium carbonate, followed by the alkaline hydrolysis of the intermediate bis(ether dinitrile) and the cyclodehydration of the resulting bis(ether diacid). A series of poly(ether imide)s bearing pendant norbornane groups were prepared from the bis(ether anhydride) with various aromatic diamines via a conventional two‐stage process that included ring‐opening polyaddition to form the poly(amic acid)s followed by thermal imidization to the poly(ether imide)s. The inherent viscosities of the poly(amic acid) precursors were 0.81–1.81 dL/g. The poly(ether imide) with m‐phenylenediamine as a diamine showed good organosolubility. Most of the cast poly(ether imide) films have had high tensile strengths and moduli. The glass‐transition temperatures of these poly(ether imide)s, except for those from rigid p‐phenylenediamine and benzidine, were recorded between 211 and 246 °C by differential scanning calorimetry. The softening temperatures of all the poly(ether imide) films stayed within 210–330 °C according to thermomechanical analysis. No polymers showed significant decomposition before 500 °C in a nitrogen or air atmosphere. A comparative study of the properties with the corresponding poly(ether imide)s without pendant substituents was also made. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1712–1725, 2002     

Synthesis of Poly(arylene ether amine)s from a Monomer Containing an Electron‐Donating Amine Group in a Nucleophilic Aromatic Substitution Reaction

Summary: Poly(arylene ether amine)s were synthesized by a nucleophilic aromatic substitution polycondensation of bis[4‐fluoro‐3‐(trifluoromethyl)phenyl]amine with several bisphenols. Even though the monomer has an electron‐donating diphenylamine moiety, which normally deactivates a nucleophilic aromatic substitution (S_NAr) reaction, the polymerization proceeded by a S_NAr reaction to give high‐molecular‐weight polymers. The polymers show good solubility in common organic solvents and have T_gs in the range of 123 °C to 177 °C.

High‐molecular‐weight poly(arylene ether amine)s synthesized by a S_NAr reaction with the monomer containing an electron‐donating diphenylamine moiety.     

BLUE LIGHT EMITTING COPOLY-(ARYLENE ETHER)S CONTAINING A 3,6- DIALKOXYPHTHALIMIDE GROUP

ABSTRACT

Four new bisphenols containing 3,6-dialkoxyphthalimide moieties were prepared in high yields. They were copolymerized with BPA or 2,5-bis(4-hydroxyphenyl)oxadiazole by reaction with decafluorobiphenyl and with NaH as base to give novel copoly(arylene ether)s. The resulting copolymers have glass-transition temperatures (Tg) ranging from 153 to 235°C and very good thermal stabilities with 5% wt loss temperatures (TGA) ranging from 378 to 499°C. These polymers show strong blue light emission in wavelengths ranging from 420 to 430 nm, while their UV absorption peaks vary from 368 to 383 nm. They have excellent solubility in common organic solvents.     

Synthesis and properties of new organo‐soluble and strictly alternating aromatic poly(ester‐imide)s from 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide and bisphenols

A series of new strictly alternating aromatic poly(ester‐imide)s having inherent viscosities of 0.20–0.98 dL/g was synthesized by the diphenylchlorophosphate (DPCP) activated direct polycondensation of the preformed imide ring‐containing diacid, 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide (I), with various bisphenols in a medium consisting of pyridine and lithium chloride. The diimide–diacid I was prepared from the condensation of 3,3‐bis[4‐(4‐aminophenoxy)phenyl]phthalide and trimellitic anhydride. Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents such as N‐methyl‐2‐pyrrolidone (NMP) and N,N‐dimethylacetamide (DMAc). Transparent and flexible films of these polymers could be cast from their DMAc solutions. The cast films had tensile strengths ranging 66–105 MPa, elongations at break from 7–10%, and initial moduli from 1.9–2.4 GPa. The glass‐transition temperatures of these polymers were recorded between 208–275 °C. All polymers showed no significant weight loss below 400 °C in the air or in nitrogen, and the decomposition temperatures at 10% weight loss all occurred above 460 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1090–1099, 2000     

Thiol–ene polymerizations using imide‐based monomers

New diene and dithiol monomers, based on aromatic imides such as benzophenone‐3,3′,4,4′‐tetracarboxylic diimide were synthesized and used in thiol‐ene polymerizations which yield poly(imide‐co‐thioether)s. These linear polymers exhibit limited solubility in various organic solvents. The molecular weights of the polymers were found to decrease with increasing imide content. The glass transition temperature (T_g) of these polymers is dependent on imide content, with T_g values ranging from ?55 °C (with no imide) up to 13 °C (with 70% imide). These thermal property improvements are due to the H‐bonding and rigidity of the aromatic imide moieties. Thermal degradation, as studied by thermogravimetric analysis, was not significantly different to the nonimide containing thiol‐ene polymers made using trimethyloylpropane diallyl ether and 3,5‐dioxa‐1,8‐dithiooctane. It is expected that such monomers may lead to increased glass transition temperatures in other thiol‐ene polymer systems as these normally exhibit low glass transition temperatures. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4637–4642     

Synthesis and characterization of aromatic poly(ether sulfone)s containing pendant sodium sulfonate groups

Poly(ether sulfone)s containing pendant sodium sulfonate groups were prepared by the aromatic nucleophilic substitution reaction of 4,4′-dichlorodiphenylsulfone ( 1 ) and sodium 5,5′-sulfonylbis (2-chlorobenzenesulfonate) ( 2 ) with bisphenols ( 3 ) in the presence of potassium carbonate in N,N-dimethylacetamide. A new monomer 2 containing the sodium sulfonate groups was synthesized by the sulfonation of 1 with fuming sulfuric acid. The polycondensation proceeded smoothly at 170°C and produced the desired poly(ether sulfone)s containing the sodium sulfonate with inherent viscosities up to 1.2 dL/g. The polymers were quite soluble in strong acid, dipolar aprotic solvents, m-cresol, and dichloromethane. The thermogravimetry of the polymers showed excellent thermal stability, indicating that 10% weight losses of the polymers were observed in the range above 460°C in nitrogen atmosphere. Both the glass transition temperatures and hydrophilicity of the polymers increased with increasing their concentrations of sodium sulfonate groups. © 1993 John Wiley & Sons, Inc.     

Highly phenylated poly(aryl ether phthalazine)s

Two series of novel amorphous poly(aryl ether phthalazine)s have been prepared via an intramolecular ring closure reaction of poly(aryl ether ketone)s (PAEKs) with hydrazine monohydrate. Fluorinated PAEKs, which display solubility in solvents incorporating a ketone functionality such as acetone or ethyl acetate, were converted to poly(aryl ether phthalazine)s to observe if these polymers would display similar solubility characteristics. The poly(aryl ether phthalazine)s have glass transition temperatures in the range of 278–320°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. The fluorinated poly(aryl ether phthalazine)s were not soluble in ketonic solvents. A series of poly(aryl ether phthalazine)s incorporating pendant 2-naphthalenyl moieties has been prepared in an attempt to produce amorphous, thermally stable polymers with high glass transition temperatures. The polymers have glass transition temperatures in the range of 287–334°C and show 5% weight loss points greater than 500°C in air and nitrogen atmospheres. Poly(aryl ether phthalazine)s undergo an exothermic reaction above the glass transition temperature. The major product of this reaction is a rearrangement of the phthalazine moieties to quiazoline moieties, however some crosslinking of the polymers occurs. Cured samples of the poly(aryl ether phthalazine)s show a small increase in the polymer T_g and are insoluble in all solvents tested. © 1996 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 34:1897–1905, 1996     

Co‐poly(aryl ether sulfone)s containing phthalimidine moiety in the main chain

Several new co‐poly(arylene ether sulfone)s have been prepared by the reaction of 4,4′‐fluorodiphenyl sulfone (FDS) with different bisphenols namely 4,4′‐isopropylidenediphenol (BPA), 4,4′‐hexafluoroisopropylidenediphenol (6F‐BPA), and N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine(PA). The homo‐poly(arylene ether sulfone)s are named as 1a, 2a, and 3a. The copolymers namely 2b, 2c, 2d and 3b, 3c, 3d have been prepared, respectively, on reaction of FDS with BPA or 6F‐BPA using different molar ratios of PA such as 25, 50, and 75. The poly(aryl ether sulfone)s 1a containing PA unit in the main chain showed a very high glass transition temperature of 280°C and an outstanding thermal stability up to 510°C for 5% weight loss under synthetic air. Depending on the mole% of PA, the glass transition temperatures of the copolymers can be varied. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 84 MPa and Young's modulus up to 3.16 GPa. The films of these polymers showed low water absorption of 0.24%. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and properties of aromatic poly (ether sulfone)s and poly (ether ketone)s based on methyl-substituted biphenyl-4,4′-diols

Novel methyl-substituted aromatic poly (ether sulfone)s and poly (ether ketone)s were synthesized from combinations of 3,3′,5,5′-tetramethylbipheny-4,4′-diol and 2,2′,3,3′,5,5′-hexamethylbiphenyl-4,4′-diol, and 4,4′-dichlorodiphenyl sulfone and 4,4′-difluorobenzo-phenone by nucleophilic aromatic substitution polycondensation. The polycondensations proceeded quantitatively in a N-methyl-2-pyrrolidone-toluene solvent system in the presence of anhydrous potassium carbonate to afford the polymers with inherent viscosities between 0.86 and 1.55 dL/g. The methyl-substituted poly (ether sulfone)s and poly (ether ketone)s showed good solubility in common organic solvents such as chloroform, tetrahydrofuran, pyridine, m-cresol, and N,N-dimethylacetamide. The tetramethyl- and hexamethyl-substituted aromatic polyethers had higher glass transition temperatures than the corresponding unsubstituted polymers, and did not decompose below 350°C in both air and nitrogen atmospheres. The films of the methyl-substituted poly (ether ketone)s became insoluble in chloroform by the irradiation of ultraviolet light, indicating the occurrence of photochemical crosslinking reactions. © 1994 John Wiley & Sons, Inc.     

Side-Chain Sulfonated Poly(arylene ether)s for Fuel Cell Applications

Summary: Poly(arylene ether sulfone)s of high molecular weight and narrow molecular weight distribution were obtained by melt polycondensation of 4,4′-difluorodiphenyl- sulfone and trimethylsilylethers of 4,4′-dihydroxydiphenylsulfone and phenylhydroquinone using CsF as catalyst. Although a block-like structure of the polymers could be expected from the course of reaction, only a single T_g ranging from 190 °C to 230 °C could be detected by DSC and which depended on the copolymer composition. Contrary to the sulfonation of similar poly(ether ether ketone)s the poly(arylene ether sulfone)s here reported were sulfonated both in the side chain and the main chain. Nonetheless the sulfonated poly(arylene ether sulfone)s showed high hydrolytic stability in water at 130 °C.     

Perfluorocyclohexenyl aryl ether polymers via polycondensation of decafluorocyclohexene with bisphenols

A novel class of semifluorinated perfluorocyclohexenyl (PFCH) aryl ether homo/copolymers was successfully synthesized with high yield through the step‐growth polymerization of commercially available bisphenols and decafluorocyclohexene in the presence of a triethylamine base. The synthesized polymers exhibit variable thermal properties depending on the functional spacer group (R). PFCH aryl ether copolymers with random and alternating architectures were also prepared from versatile bis‐perfluorocyclohexenyl aryl ether monomers. The PFCH polymers show high thermal stabilities with a 5% decomposition temperature ranging from 359 to 444 °C in air and nitrogen atmosphere. These semifluorinated PFCH aromatic ether polymers contain intact enchained PFCH olefin moieties, making further reactions such as crosslinking and application specific functionalization possible. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 232–238     

Synthesis and characterization of poly(aryl ether imide)s containing electroactive perylene diimide and naphthalene diimide units

The synthesis and polymerization of two new electroactive bisphenols derived from 3,4,9,10‐perylenetetracarboxylic dianhydride and 1,4,5,8‐naphthalenetetracarboxylic dianhydride with 2‐(4‐aminophenyl)‐2‐(4‐hydroxyphenyl)propane, respectively, are described. Copolymerization using the two new bisphenols and 4,4′‐isopropylidenediphenol with bis(4‐fluorophenyl)sulfone and 4,4′‐difluorobenzophenone, afforded a series of soluble electrochromic poly(aryl ether imide)s with glass‐transition temperatures ranging from 160 to 315 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3467–3475, 2000     

New poly(arylene ether)s with pendant phosphonic acid groups

Soluble brominated poly(arylene ether)s containing mono‐ or dibromotetraphenylphenylene ether and octafluorobiphenylene units were synthesized. The polymers were high molecular weight (weight‐average molecular weight = 115,100–191,300; number‐average molecular weight = 32,300–34,000) and had high glass‐transition temperatures (>279 °C) and decomposition temperatures (>472 °C). The brominated polymers were phosphonated with diethylphosphite by a palladium‐catalyzed reaction. Quantitative phosphonation was possible when 50 mol % of a catalyst based on bromine was used. The diethylphosphonated polymers were dealkylated by a reaction with bromotrimethylsilane in carbon tetrachloride followed by hydrolysis with hydrochloric acid. The polymers with pendant phosphonic acid groups were soluble in polar solvents such as dimethyl sulfoxide and gave flexible and tough films via casting from solution. The polymers were hygroscopic and swelled in water. They did not decompose at temperatures of up to 260 °C under a nitrogen atmosphere. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3770–3779, 2001     

Synthesis and characterization of poly(ether naphthalimide)s

A series of new poly(ether imide)s containing the naphthalimide moiety were prepared from bis(4-fluorobenzoyl)naphthalimides and several bisphenols by aromatic nucleophilic displacement polymerization. These polyimides had inherent viscosities in the range of 0.31–1.04 dL/g in chloroform and glass transition temperatures of 283.0–341.6°C by differential scanning calorimetry. The onset temperature for 5% weight loss for all the polymers was over 448°C, as assessed by thermogravimetry at a heating rate 10°C/min in nitrogen. In addition, these novel polyimides exhibited good solubility in organic solvents including N-methyl-2-pyrrolidone, N,N-dimethylformamide, N,N-dimethylacetamide, 1,1,2,2-tetrachloroethane and chloroform. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3227–3231, 1999     

Synthesis of poly(ether-ketone-amide)s by palladium-catalyzed polycondensation of aromatic dibromides containing ether ketone structure,aromatic diamines,and carbon monoxide

Aromatic poly(ether-ketone-amide)s were prepared by the palladium-catalyzed polycondensation of aromatic dibromides containing ether ketone units, aromatic diamines, and carbon monoxide. Polymerizations were carried out in N,N-dimethylacetamide (DMAc) in the presence of palladium catalyst, triphenylphosphine, and 1,8-diazabicyclo [5,4,0]-7-undecene (DBU), and resulted in poly(ether-ketone-amide)s with inherent viscosities up to 0.82 dL/g under mild conditions. The polymers were quite soluble in strong acid, dipolar aprotic solvents, and pyridine. Thermogravimetry of the polymers showed excellent thermal stability, indicating that 10% weight losses of the polymers were observed in the range above 400°C in nitrogen atmosphere. The glass transition temperatures of the polymers were about 200°C, which are higher than those of poly(ether-ketone) analogues. These polymers also showed good tensile strength and tensile modulus. © 1994 John Wiley & Sons, Inc.     

Synthesis and properties of poly(ether imide)s derived from 2,6-bis(3,4-dicarboxyphenoxy)naphthalene dianhydride and aromatic diamines

A new naphthalene unit-containing bis(ether anhydride), 2,6-bis(3,4-dicarboxyphenoxy)naphthalene dianhydride, was synthesized in three steps starting from the nucleophilic nitrodisplacement reaction of 2,6-dihydroxynaphthalene and 4-nitrophthalonitrile in N,N-dimethylformamide (DMF) solution in the presence of potassium carbonate, followed by alkaline hydrolysis of the intermediate bis(ether dinitrile) and subsequent dehydration of the resulting bis(ether diacid). High-molar-mass aromatic poly(ether imide)s were prepared using a conventional two-step polymerization process from the bis(ether anhydride) and various aromatic diamines. The intermediate poly(ether amic acid)s had inherent viscosities of 0.65–2.03 dL/g. The films of poly(ether imide)s derived from two rigid diamines, i.e. p-phenylenediamine and benzidine, crystallized during the thermal imidization process. The other poly(ether imide)s belonged to amorphous materials and could be fabricated into transparent, flexible, and tough films. These aromatic poly(ether imide) films had yield strengths of 104–131 MPa, tensile strengths of 102–153 MPa, elongation to break of 8–87%, and initial moduli of 1.6–3.2 GPa. The glass transition temperatures (T_g's) of poly(ether imide)s were recorded in the range of 220–277°C depending on the nature of the diamine moiety. All polymers were stable up to 500°C, with 10% weight loss being recorded above 550°C in both air and nitrogen atmospheres. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1657–1665, 1998